Snap Mode in AutoCAD

7/25/2019 Snap Mode in AutoCAD

1/24

SNAP MODE IN AUTOCAD

REPRSENTED BY:

ADMEC MULTIMEDIA INSTITUTE

PRESENTED BY:

ANKIT SINGH

A

D

M

E

C


2/24

INFER CONSTRAINT

This optionsshortcut key is ctrl + shift + i.By using this option when we are creating an objectthen geometric constraints is apply on the object

automatically.This option automatically applies geometric

constraints between the object which we arecreating and point attached to object snap. Infer

constraints are applied on object when the objectscondition is constraints. In the inferringconstraints result the objects position are notchanged.


3/24

HOW TO USE THE INFER

CONSTRAINT

Click the Infer button in the status bar.


4/24

When you are on the Infer button then object willmade as same.


5/24

SNAP MODE

Shortcut of Snap mode is F9.For switch on the snap mode we can press the snap

mode button.


6/24

SNAP SPACING

It is stop the cursor movement to specifiedXandYgaping to the location of Rectangular Grid of Snap.

Snap X spacing

If the snap spacing direction isXthen the valuewill be positive.

Snap Y SpacingIf the snap spacing direction isYthen the value

will be positive.


7/24

Specifies the Snap

and Grid Setting


8/24

GRID DISPLAY

Shortcut of Grid Display is F7.For switch on the Grid Display we can press the GRID

button in the status bar.


9/24

When we will click the Grid button then displaypattern would be changed in to rectangular formDot.It is very useful to create the object too fast.


10/24

ORTHO MODE

Shortcut of Ortho mode is F8.For switch on the Ortho mode press the ORTHObutton

in the status bar.


11/24

When we are switch on the Ortho mode then we cancreate the straight line in the direction ofXorY. Itis very useful option.


12/24

POLAR TRACKING

Shortcut of the Polar Tracking is F10.For switch on the Polar Tracking press the POLAR

button in status bar.


13/24

When we are switch on the polar button then wecan maintain the value of length and angle ofthe object easily.


14/24

OBJECT SNAP

Shortcut of the Object Snap is F3.For switch on the Object Snap press the OSNAPbuttonin the status bar.


15/24

It is very useful to create the object. When we areswitch on the OSNAPthen we can see midpoint,nearest, center and endpoint in the object.


16/24

OBJECT SNAP

TRACKINGShortcut of the Object Snap Tracking is F11.

For switch on the Object Snap Tracking press the

OTRACKbutton in the status bar.


17/24

These are OTRACK sub tools and these are

very important to create an object.


18/24

DYNEMIC UCS

Shortcut of the Dynamic UCSis F6.

For switch on the Dynamic UCSpress the DUCSbutton in the status bar.


19/24

This is maintain the length value according toX,Yand Zaxis. DUCSis very useful in3DModeling.


20/24

DYNAMIC INPUT

Shortcut of the Dynamic Input is F12.For switch on the Dynamic Input press the DYNbuttonin the status bar.


21/24

This is maintain the length and angle of theobject it is very useful in3DModeling.


22/24

LINEWEIGHT

For switch on the Line weight press the LWTbuttonon the status bar. Its used to see the weight of the line.


23/24

- Contact Us -

ADMEC MULTIMEDIA INSTITUTE

Leader in Animation & Digital

Media Education

ISO 9001 : 2008 CERTIFIED

Visit Our Websites

www.admecindia.co.in

www.cadtraininginstitute.comPhones: +91-9811-8181-22, +91-9911-7823-50


24/24

THANKYOU

Snap Mode in AutoCAD

Documents

Transcript of Snap Mode in AutoCAD