![W E ? D L J H F : = G ? L B A F D H E ? ; : G B Y B - UTMfizica.utm.md/documents_pdf/Indrumar de lab... · i; ] ^ _ b - . / b p. b g b g b g g n gg - . b b g g z g b b g, z g. b g,](https://static.fdocuments.in/doc/165x107/5ec41a37735be534d03bba1d/w-e-d-l-j-h-f-g-l-b-a-f-d-h-e-g-b-y-b-de-lab-i-b-.jpg)
SMITH JAY R. U M B IN G AN DRANA LOCATION G P L E B …
2
REV. DATE DESCRIPTION BY CKD. BY WEIGHT POUNDS VOLUME CUBIC FEET FIGURE NUMBER LOCATION FIGURE NUMBER DIMENSIONS ARE SUBJECT TO MANUFACTURERS TOLERANCE AND CHANGE WITHOUT NOTICE WE CAN ASSUME NO RESPONSIBILITY FOR USE OF SUPERSEDED OR VOID DATA DRAWN BY: CHECKED BY: APPROVED BY: SCALE: SIZE A DRAWING NUMBER NONE DATE: TBW PJ S9940 B 3-23-18 PJ 9940 9940 9940 6" WIDE ZIP TRENCH™ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov FUNCTION: Used in all surface drainage applications. May be assembled in any length utilizing interlocking tongue and groove ends. This reduces installation times and cost, providing an engineered, sloped solution for drainage requirements. REGULARLY FURNISHED: 3 meter (9.84') 100% Polypropylene with UV Inhibitors Assemled to Coated Steel Frame with Channels Connect with 1 1/4" Overlap Joint. Design has a Built In Slope of 0.6% with Radiused Bottom. Supplied with Secured Grate Per Specification. VARIATIONS: Grate Specifications (See Back) Closing End Cap Shallow -ES Closing End Cap Deep -ED Horizontal Outlet 4" -H4 4" NO-HUB Bottom Outlet -V4 Note: This Trench Drain System is Designed for "On Grade Applications Only" as There are No Provisions for a Flashing Flange or Flashing Clamp OPTIONAL RAIL MATERIAL: Galvanized Steel Type 304 Stainless Steel Universal Closing End Caps Specify Shallow (-ES) or Deep End (-ED) ENLARGED END VIEW 1 2 3 4 5 6 7 8 9 10 11 12 3N 6N 3N1 6N1 9N 12N 9'-10 1/8" (3000) SIDE VIEW TOP VIEW 4 13/16" (122) - 13 13/16" (351) 29 1/2" (749) 59 1/8" (1500) 29 1/2" (749) Bottom Outlet 4" DIA Female End Male End Welded Installation Device For Rebar Support (4 Per Frame) (Rebar Posts By Others) 5 1/8" (130) 12 7/8" (327) 3 5/8" (92) 13/16" (21) 118'-1 11/16" (36 meters) Sloped Non-sloping 3 MeterNeutral Channels NOTE: Dimensions shown in parentheses are in millimeters. JAY R. SMITH MFG. CO. ® MEMBER OF MORRIS GROUP INTERNATIONAL POST OFFICE BOX 3237 MONTGOMERY, ALABAMA 36109-0237 (USA) TEL: 334-277-8520 FAX: 888-377-7818 www.jrsmith.com CUSTOMER DRIVEN SMITH ® MEMBER OF: ASPE ® S A N I T A R Y E N G I N E E R I N G P r e v e n tio n R ath er T h a n C u r e SINCE 1926 P L U M B I N G A N D D R A I N A G E I N S T I T U T E M E M B E R ® MEM B E R Non-sloping 1 Meter Channel Non-sloping 1 Meter Channel 4" Horizontal Outlet End Cap-H4 (Fits Channels #4-12N) A 2-28-20 Added 3N1 & 6N1 MW PJ B 7-7-21 Corrected Dim. on Top View KK PJ
Transcript of SMITH JAY R. U M B IN G AN DRANA LOCATION G P L E B …
REV. DATE DESCRIPTION BY CKD. BY
WEIGHTPOUNDS
VOLUMECUBIC FEET
FIGURE NUMBER
LOCATIONFI
GU
RE
NU
MBE
R
DIM
ENSI
ON
S AR
E SU
BJEC
T TO
MAN
UFA
CTU
RER
S TO
LER
ANC
E AN
D C
HAN
GE
WIT
HO
UT
NO
TIC
EW
E C
AN A
SSU
ME
NO
RES
PON
SIBI
LITY
FO
R U
SE O
F SU
PER
SED
ED O
R V
OID
DAT
A
DR
AWN
BY:
CH
ECKE
D B
Y:AP
PRO
VED
BY:
SCAL
E:SI
ZE AD
RAW
ING
NU
MBE
RN
ON
ED
ATE:
TBW
PJS9
940
B3-
23-1
8PJ
9940
9940
9940 6" WIDE ZIP TRENCH™
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
FUNCTION: Used in all surface drainage applications. May be assembled in any length utilizing interlocking tongue andgroove ends. This reduces installation times and cost, providing an engineered, sloped solution for drainage requirements.
REGULARLY FURNISHED:3 meter (9.84') 100% Polypropylene withUV Inhibitors Assemled to Coated SteelFrame with Channels Connect with 1 1/4"Overlap Joint. Design has a Built In Slopeof 0.6% with Radiused Bottom. Suppliedwith Secured Grate Per Specification.
VARIATIONS:Grate Specifications (See Back)Closing End Cap Shallow -ESClosing End Cap Deep -EDHorizontal Outlet 4" -H44" NO-HUB Bottom Outlet -V4
Note: This Trench Drain System is Designedfor "On Grade Applications Only" as There areNo Provisions for a Flashing Flange or Flashing Clamp
OPTIONAL RAIL MATERIAL:Galvanized SteelType 304 Stainless Steel
Universal Closing End CapsSpecify Shallow (-ES) or Deep End (-ED)
ENLARGED END VIEW
1 2 3 4 5 6 7 8 9 10 11 12
3N 6N
3N1 6N1
9N 12N
9'-10 1/8" (3000)
SIDE VIEW
TOP VIEW
4 13/16" (122) -13 13/16" (351)
29 1/2" (749)59 1/8" (1500) 29 1/2" (749)
Bottom Outlet 4" DIA
Female End Male End
Welded Installation DeviceFor Rebar Support(4 Per Frame)(Rebar Posts By Others)
5 1/8"(130)
12 7/8" (327)
3 5/8"(92)
13/16" (21)
118'-1 11/16" (36 meters) Sloped
Non-sloping3 MeterNeutral Channels
NOTE: Dimensions shown inparentheses are in millimeters.
JAY R.SMITH MFG. CO.®
MEMBER OF MORRIS GROUP INTERNATIONALPOST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 888-377-7818 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
SINCE 1926
PL
UMBING AND DRAINAGE
INSTITUTE
M E M B E R
®
M E M B E R
Non-sloping1 Meter Channel
Non-sloping1 Meter Channel
4" Horizontal Outlet End Cap-H4(Fits Channels #4-12N)
A 2-28-20 Added 3N1 & 6N1 MW PJB 7-7-21 Corrected Dim. on Top View KK PJ
REV. DATE DESCRIPTION BY CKD. BY
WEIGHTPOUNDS
VOLUMECUBIC FEET
FIGURE NUMBER
LOCATIONFI
GU
RE
NU
MBE
R
DIM
ENSI
ON
S AR
E SU
BJEC
T TO
MAN
UFA
CTU
RER
S TO
LER
ANC
E AN
D C
HAN
GE
WIT
HO
UT
NO
TIC
EW
E C
AN A
SSU
ME
NO
RES
PON
SIBI
LITY
FO
R U
SE O
F SU
PER
SED
ED O
R V
OID
DAT
A
DR
AWN
BY:
CH
ECKE
D B
Y:AP
PRO
VED
BY:
SCAL
E:SI
ZE AD
RAW
ING
NU
MBE
RN
ON
ED
ATE:
TBW
PJS9
940B
SD
3-23
-18
PJ99
40B
S
9940BSWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
9940 6" WIDE ZIP TRENCH™Channel Number
Deep End Invert Inch mm
Slope Single ChannelEst. CFS Est. GPM
Weight Lbs.Frame + Channel
0.6% .29 130 38.00 9940-2
141
.31 139 39.00 9940-3
5.56
160 .34 153 40.00
9940-4
6.31
179 .36 162 41.00
9940-5
7.06 198
.39 175 42.00 9940-6
7.81 267
.42 189 44.00
9940-7
8.56
.45 202 45.00 9940-8
256
.47 211 47.00
9940-6N9940-6N1
44.00
9940-9
10.06 275
.49 220 49.00 9940-9N 51.00 9940-10
10.81
313 .53 238 51.50
9940-11
12.31
.56 251 51.00 9940-12 .58 261 51.00 9940-12N
351 51.00
13.81
9940-1
0.0%
0.0%
0.0%
HYDRAULIC CAPACITY SHALLOW / DEEP END DEPTHS 9940 SYSTEM
Note: Channel flow rates based on channels less grates and open ended.
*Supplied with Quick-lok® securing device regularly furnished
9940-3N9940-3N1
40.00 13.00
15.00
0.0%
0.6% 0.6%
0.6% 0.6% 0.6%
0.6% 0.6% 0.6% 0.6% 0.6% 0.6%
179 7.06
236
9.31
236 9.31
294
11.56
294 11.56
332
13.06
351 13.81
Shallow End Invert Inch mm
122 4.81
141 5.56
179
7.06 179 7.06 0.0% 179 7.06
179
7.06
198 7.81
236
9.31 256
10.06
294
11.56
351
13.81
160
6.31
236 0.0% 236 9.31 9.31 236
8.56 267
9.31 275
10.81
294 11.56
313
12.31
332 13.06
*******
**
***
****
*****
*
Light Duty DIN 19580 Load Class A:3500 lbs - 70 psi. For pedestrian,wheelchair and bicycle traffic.
9870-410-GP - 1/4 dia perforated galv. steelgrate (28.30 sq. in.)9870-420-G - 3 1/4 x 3/8 slotted galv. steel grate(35.20 sq. in.)9870-451-SSPA - 1/4 dia perforated stainless steelgrate (28.30 sq. in.)9870-494-PADAB - 1 3/4 x 5/16 longitudinal slotblack polypropylene grate (27.40 sq. in.)9870-494-PADAG - 1 3/4 x 5/16 longitudinal slotgray polypropylene grate (27.40 sq. in.)9870-450-ss - 3 1/4 x 3/8 slotted stainless steelgrate (42.60 sq. in.)
Medium Duty DIN 19580 Load Class B:28100 lbs - 581 psi. For light vehicle traffic.
9870-447-SSADA - 13/16 x 3/16 longitudinalstainless steel slot bar grate (58.40 sq. in.)
Heavy Duty DIN 19580 Load Class C:56,000 lbs - 1,162 psi. For commercial pneumatictire traffic patterns, forklifts (pneumatic tire) andtractor trailers (pneumatic tire).
9870-405-GM - 13/16 x 1/2 longitudinal galv. steelslot bar grate (121.10 sq. in.)9870-411-GPHD - 1/4 dia perforated galv. steelgrate (28.30 sq. in.)9870-425-GHD- 3 1/4 x 3/8 slotted galv. steel grate(35.20 sq. in.)9870-430-SSM - 13/16 x 1/2 longitudinal stainlesssteel slot bar grate (121.10 sq. in.)9870-455-SSHD - 3 1/4 x 3/8 slotted stainless steelgrate (42.60 sq. in.)9870-462-DGC - 3 15/16 x 3/8 ductile iron slottedgrate (24.00 sq. in)9870-465-SSP- 1/4 dia perforated stainless steelgrate (28.30 sq. in.)9870-487-MADAC - 1 3/4 x 5/16 longitudinal ductileiron slotted grate (23.00 sq. in)9870-479-MD - Mosaic pattern ductile iron grate(19.50 sq. in.)9870-481-ID - Iron Decorative pattern ductile irongrate (19.00 sq. in.)9870-492-RC - 1 1/2 x 13/16 slotted resin compositegrate (16.30 sq. in.)
Extra Heavy Duty, DIN 19580 Class E:135,000 lbs - 2,788 psi. For commercial solid tiretraffic patterns, forklifts and impacts from steelstruts or metal wheels.
9870-435-GHDE - 3 1/4 x 3/8 slotted galv. steelgrate (42.60 sq. in.)9870-461-M - 3 15/16 x 3/8 ductile ironslotted grate (21.00 sq. in.)9870-478-MADA - 1 3/4 x 5/16 longitudinalductile iron slotted grate (14.30 sq. in.)9870-490-SSHDE - 1 3/4 x 3/8 slottedstainless steel grate (42.60 sq. in.)
A 6-21-18 Added Grates TBW PJB 3-20-19 Revised Load Class C MW PJC 2-28-20 Revised Table MW PJD 9-15-20 Added Grate (9870-450-SS) MW MD
JAY R.SMITH MFG. CO.®
MEMBER OF MORRIS GROUP INTERNATIONALPOST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 888-377-7818 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
SINCE 1926
PL
UMBING AND DRAINAGE
INSTITUTE
M E M B E R
®
M E M B E R
![g Z H P ? G D : B K D H ? A H G B G G H F B G : G K B J H ...На правах рукописи K l _ i Z g h e H e _ ] h \ g Z H P ? G D : B K D H ? A H G B G G H F B G : G K B J](https://static.fdocuments.in/doc/165x107/60665ac94fb99e770f7b94fb/g-z-h-p-g-d-b-k-d-h-a-h-g-b-g-g-h-f-b-g-g-k-b-j-h-.jpg)
