Skid Steer Quick Hitch SH35 · 11/23/15 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M 1...

Table of Contents

Cover photo may show optional equipment not supplied with standard unit.

Read the Operator’s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!

!© Copyright 2015 Printed

22130

320-019M

SH35 Category 1 & 2

Skid Steer Quick Hitch

Operator’s Manual

11/23/15

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 5Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . 5

Section 1: Assembly & Setup . . . . . . . . . . . . . 6Skid Steer Loader Requirements . . . . . . . . . . . . . . 6Skid Steer Loader Hook-Up . . . . . . . . . . . . . . . . . . . 6Center Hook Adjustment . . . . . . . . . . . . . . . . . . . . . 6Implement Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . 7Spare Bushings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Implement Unhooking . . . . . . . . . . . . . . . . . . . . . . . 8

Section 2: Operating Instructions . . . . . . . . . 9Transporting and Use . . . . . . . . . . . . . . . . . . . . . . . 9Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . 9

Section 3: Maintenance & Lubrication . . . . . 10Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Pivot points . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Section 4: Specifications & Capacities . . . . 11

Section 5: Features & Benefits . . . . . . . . . . . 12

Section 6: Torque Values Chart . . . . . . . . . . 13

Section 7: Warranty . . . . . . . . . . . . . . . . . . . 15

Table of Contents

SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M

© Copyright 2015 All rights Reserved

Land Pride provides this publication “as is” without warranty opreparation of this manual, Land Pride assumes no responsibilityof the information contained herein. Land Pride reserves the righproduct at the time of its publication, and may not reflect the prod

Land

All other brands and product names are

Printed

11/23/15

f any kind, either expressed or implied. While every precaution has been taken in the for errors or omissions. Neither is any liability assumed for damages resulting from the uset to revise and improve its products as it sees fit. This publication describes the state of thisuct in the future.

Pride is a registered trademark.

trademarks or registered trademarks of their respective holders.

in the United States of America.

Important Safety InformationTable of Contents▲

Important Safety Information
These are common practices that may or may not be applicable to the products described in this manual.
!Be Aware of Signal WordsA Signal word designates a degree or level of hazard seriousness. The signal words are:

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded.

! DANGER

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

! WARNING

! CAUTION

For Your Protection▲ Thoroughly read and understand

the “Safety Label” section, read all instructions noted on them.

Avoid Underground Utilities▲ Dig Safe, Call 811.

Always contact your local utility companies (electrical, telephone, gas, water, sewer, and others) before digging so that they may mark the location of any underground services in the area.

▲ Be sure to ask how close you can work to the marks they positioned.

Safety at All TimesThoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.

▲ The operator must not use drugs or alcohol as they can change the alertness or coordination of that person while operating equipment. The operator should, if taking over-the-counter drugs, seek medical advice on whether he/she can safely operate the equipment.

▲ Operator should be familiar with all functions of the unit.

▲ Make sure all guards and shields are in place and secured before operating implement.

▲ Keep all persons away from equipment and work area.

▲ Start skid steer with steering levers and hydraulic controls in neutral.

▲ Operate implement and loader arms from the driver’s seat only.

▲ Dismounting from a moving unit can cause serious injury or death.

▲ Do not allow anyone to stand between skid steer and implement while hooking-up to implement.

▲ Keep hands, feet, and clothing away from power-driven parts.

▲ Watch out for objects overhead and along side such as fences, buildings, wires, trees, limbs, etc., while transporting and operating attached implement.

▲ Detach and store implement in an area where children normally do not play. Secure implement by using blocks and supports.

11/23/15

Parts Manual QR LocatorThe QR (Quick Reference) code on the cover and to the left will take you to the Parts Manual for this equipment. Download the appropriate App on your smart phone, open the App, point your phone on the QR code and take a picture

Look For The Safety Alert SymbolThe SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control, and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.

1SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M

.

Dealer QR LocatorThe QR code on the left will link you to available dealers for Land Pride products. Refer to Parts Manual QR Locator on this page for detailed instructions.

2 SH35 Category 1 & 2 Skid Steer Quick Hitch

Important Safety InformationTable of Contents


Shutdown and Storage

Before leaving operator’s seat:▲ Lower lift arms and put

attachment flat on the ground. ▲ Turn off engine and engage park

brake.▲ If included, raise seat bar and

move controls until both lock.▲ Remove key to prevent

unauthorized starting.▲ Use steps, grab-handles and

skid-resistant surfaces when getting on or off the loader.

▲ Detach and store implements in an area where children normally do not play. Secure implement by using blocks and supports.

OFF

REMOVE

Use Safety Lights and Devices▲ Slow moving tractors,

self-propelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night.

▲ Flashing warning lights and turn signals are recommended whenever driving on public roads.

Transport Safely▲ Comply with state and local laws.▲ Never travel at a speed which does

not allow adequate control of steering and stopping. Some rough terrains require a slower speed.

▲ Avoid contact with any over head utility lines or electrically charged conductors.

▲ Always drive with load on end of loader arms low to the ground.

▲ Always drive straight up and down ramps with load on “uphill” side of skid steer.

▲ Engage park brake when stopped on an incline.

320-019M

▲ IMPORTANT: Do not tow a load that is more than double the weight of the vehicle towing the load.

▲ Use towing vehicle and trailer of adequate size and capacity. Secure equipment towed on a trailer with tie downs and chains.

▲ Sudden braking can cause a towed trailer to swerve and upset. Reduce speed if towed trailer is not equipped with brakes.

Practice Safe Maintenance▲ Understand procedure before doing

work. Use proper tools and equipment, refer to Operator’s Manual for additional information.

▲ Work in a clean dry area.▲ Lower attached implement to the

ground and follow all shutdown procedures before leaving the operator’s seat to perform maintenance.

▲ Allow implement to cool completely before working on it.

▲ Disconnect battery ground cable (-) before servicing or adjusting electrical systems or before welding on implement.

▲ Do not grease or oil implement while it is in operation.

▲ Inspect all parts. Make sure parts are in good condition & installed properly.

▲ Remove buildup of grease, oil, or debris.

▲ Remove all tools and unused parts from implement before operation.

11/23/15

311/23/15 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M



Prepare for Emergencies▲ Be prepared if a fire starts.▲ Keep a first aid kit and fire

extinguisher handy.▲ Keep emergency numbers for

doctor, ambulance, hospital, and fire department near phone.

Wear Protective Equipment▲ Wear protective clothing and

equipment appropriate for the job. Clothing should be snug fitting without fringes and pull strings to avoid entanglement with moving parts.

▲ Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hearing protection such as earmuffs or earplugs.

▲ Operating equipment safely requires the operator’s full attention. Avoid wearing radio headphones while operating machinery.

Use Seat Belt and ROPS▲ Operate only skid steers equipped

with a Roll-Over Protective Structure (ROPS) and seat belt.

▲ Fasten seat belt snugly and securely to help protect against serious injury or death from falling and skid steer overturn.

▲ Wearing protective equipment such as safety shoes, safety glasses, hard hat, and ear plugs is highly recommended.

911

Keep Riders Off Machinery▲ Never carry riders or use

machinery as a person-lift.▲ Riders obstruct operator’s view. ▲ Riders could be struck by foreign

objects or thrown from the machine.

▲ Never allow children to operate equipment.

Tire Safety▲ Tire changing can be dangerous

and should be performed by trained personnel using the correct tools and equipment.

▲ When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly. Use a safety cage if available.

▲ When removing and installing wheels, use wheel handling equipment adequate for the weight involved.

Avoid High Pressure Fluids Hazard▲ Escaping fluid under pressure can

penetrate the skin causing serious injury.

▲ Avoid the hazard by relieving pressure before disconnecting hydraulic lines or performing work on the system.

▲ Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system.

▲ Use a piece of paper or cardboard, NOT BODY PARTS, to check for suspected leaks.

▲ Wear protective gloves and safety glasses or goggles when working with hydraulic systems.

▲ DO NOT DELAY. If an accident occurs, see a doctor familiar with this type of injury immediately. Any fluid injected into the skin or eyes must be treated within a few hours or gangrene may result.


Safety LabelsYour Quick Hitch comes equipped with all safety labels in place. They were designed to help you safely operate your implement. Read and follow their directions.

1. Keep all safety labels clean and legible.2. Refer to this section for proper label placement. Replace

all damaged or missing labels. Order new labels from your nearest Land Pride dealer. To find your nearest dealer, visit our dealer locator at www.landpride.com.

3. Some new equipment installed during repair requires safety labels to be affixed to the replaced component as

4 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M

18440

18441

specified by Land Pride. When ordering new components make sure the correct safety labels are included in the request.

4. Refer to this section for proper label placement.To install new labels:a. Clean surface area where label is to be placed.

b. Spray soapy water onto the cleaned area.

c. Peel backing from label and press label firmly onto the surface.

d. Squeeze out air bubbles with edge of a credit card or with a similar type of straight edge.

11/23/15

818-866CCaution: Pinch Point

838-167CDanger: Crushing Hazard

IntroductionTable of Contents

IntroductionThe parts on your Quick Hitch have been specially Land Pride welcomes you to the growing family of new

product owners.

This Quick Hitch has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance, and safe operating practices will help you get years of satisfactory use from this machine.

ApplicationThe SH35 Series Skid Steer Quick Hitch is designed and built by Land Pride to provide quick and easy three-point attachment to category 1 or 2 implements that are not driven or powered by a PTO shaft. Box blades, landscape rakes, soil pulverizers, hydraulically driven power rakes, and other like implements work extremely well with this hitch. Rental yards, implement dealers, and owners of larger implement fleets will find that the SH35 serves an excellent tool for spotting, relocating, and organizing implements on large lots. This unit also has expanded versatility with use of a class 2 receiver and convenient storage for a ball hitch. An adjustable top hook makes attachment to a broader range of implements even easier.

See “Specifications & Capacities” on page 11 and “Features & Benefits” on page 12 for additional information and performance enhancing options.

Using This Manual• This Operator’s Manual is designed to help familiarize

you with safety, assembly, operation, adjustments, troubleshooting, and maintenance. Read this manual and follow the recommendations to help ensure safe and efficient operation.

• The information contained within this manual was current at the time of printing. Some parts may change slightly to assure you of the best performance.

• To order a new Operator’s or Parts Manual, contact your authorized dealer. Manuals can also be downloaded, free-of-charge, from our website at www.landpride.com

Terminology“Right” or “Left” as used in this manual is determined by facing the direction the machine will travel while in use unless otherwise stated.

Definitions

Owner AssistanceThe Online Warranty Registration should be completed by the dealer at the time of purchase. This information is necessary to provide you with quality customer service.

IMPORTANT: A special point of information related to the following topic. Land Pride’s intention is this information must be read & noted before continuing.

NOTE: A special point of information that the operator should be aware of before continuing.

11/23/15

designed by Land Pride and should only be replaced with genuine Land Pride parts. Contact a Land Pride dealer if customer service or repair parts are required. Your Land Pride dealer has trained personnel, repair parts, and equipment needed to service the implement.

Serial NumberModel No. _____________Serial No. ______________

For quick reference and prompt service, record model and serial number in the spaces provided above and again on warranty page 15. Always provide model number and serial number when ordering parts and in all correspondences with your Land Pride dealer. Refer to Figure 1 for location of your serial number plate.

Serial Number Plate LocationFigure 1

Further AssistanceYour dealer wants you to be satisfied with your new Quick Hitch. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested:

1. Discuss the matter with your dealership service manager making sure that person is aware of any problems you may have and has had the opportunity to assist you.

2. If you are still not satisfied, seek out the owner or general manager of the dealership, explain the problem, and request assistance.

3. For further assistance write to:

Land PrideService Department

P.O. Box 5060Salina, KS 67402-5060

E-mail [email protected]

18441


Section 1: Assembly & SetupTable of Contents

Section 1: Assembly & Setup5. Push skid steer loader release handles down to drive
Skid Steer Loader Requirements
This SH35 Quick Hitch is designed for skid steer loaders.

Skid Steer Loader Hook-UpRefer to Figure 1-1

! CAUTIONDo not stand between skid steer loader and implement during hookup.

1. Drive skid steer loader slowly to the Quick Hitch making sure front hitch plate of the skid steer loader is parallel with the Quick Hitch frame.

2. Tilt top of skid steer loader hitch plate slightly forward.

3. Place top of skid steer loader hitch plate under the top angled bar of the Quick Hitch.

4. Slowly lift skid steer loader hitch until Quick Hitch and skid steer loader hitch have come together.

Skid Loader Hook-UpFigure 1-1

IMPORTANT: Maximum weight of attached implement shall not exceed 2,800 lbs. at 24” from implements’ lower hitch pins.

NOTE: Ballast may need to be added to your skid steer loader to maintain steering control. Refer to your skid steer loader Operator Manual to determine whether or not to add ballast.

IMPORTANT: Some Cat. 1 and Cat. II implements may not meet Quick Hitch standards. Any modification made to the Quick Hitch or implement to accommodate hook-up could void the warranty.

22137

Top Angle Bar

Bottom Slots

Positioning Pins with Cotter Hair Pins


hitch pins through bottom slots in the Quick Hitch frame and to lock release handles down.

Center Hook AdjustmentRefer to Figure 1-2 & Figure 1-3The Quick Hitch top hook normally is adjusted for a standard Category I or Category II configuration. Adjust top hook if implement being attached is not a true standard Category I or II configuration. (See Figure 1-3)

! DANGERCrushing Hazard between Quick Hitch and Implement. Do not allow anyone to stand between the Quick Hitch and implement while backing-up to implement. Never operate hydraulic lift controls while someone is near the lift arms and/or Quick Hitch.

1. Lower skid steer lift arms and carefully move Quick Hitch forward to align its lower support hooks with implement’s lower 3-point hitch pins. Verify upper Quick Hitch top hook also aligns with implement’s center hitch pin. (See Figure 1-3 on page 7.)

2. Skip to Implement Hook-Up if the three hooks align with implement’s three hitch pins.

3. Engage park brake, shut engine off, and remove switch key before dismounting from skid steer loader.

4. Remove hairpin cotter and clevis pins securing Quick Hitch upper hook. Move hook up or down to align with implement’s upper hitch pin.

5. Replace clevis pins and their hairpin cotters.

Upper Hook AdjustmentFigure 1-2

NOTE: Skid steer hook-up is required before proceeding with center hook adjustment.

Clevis Pins

Upper Hook

Hairpin Cotter

22140

11/23/15


Implement Hook-Up

Refer to Figure 1-1Determine hitch category of implement being hooked up.

• Category I hitches will have 7/8” diameter lower hitch pins and a 3/4” diameter upper hitch pin.

• Category II hitches will have 1 1/8” diameter lower hitch pins and a 1” diameter upper hitch pin.

Remove 1/2” x 3” positioning pins to reposition lower 3-point hooks on the Quick Hitch. Move hooks to the inward positions if implement is a Category 1 hitch and to the outward positions if implement is a Category II hitch. Replace 1/2” x 3” positioning pins and secure with cotter hair pins.

! DANGERCrushing Hazard between Quick Hitch and Implement. Do not allow anyone to stand between the Quick Hitch and implement during hook-up operations. Never operate hydraulic lift controls while someone is near the lift arms and/or Quick Hitch.

! DANGERHydraulic fluid under pressure can penetrate skin. Wear protective gloves and safety glasses or goggles when working

NOTE: Hook-up of Quick Hitch to the skid steer loader is required before proceeding with hook-up to implement.

.

11/23/15

ImplementFigur

18442

Release Handle

with hydraulic systems. Use a piece of cardboard or wood rather than hands when searching for hydraulic leaks. If hydraulic fluid is injected into the skin, it must be surgically removed within a few hours by a doctor or gangrene may result.

! CAUTIONRelease Handles have areas where pinching can occur. Keep hands, fingers and other body parts away from pivoting areas of the release handles. Always use handle grips.

Refer to Figure 1-31. Two 320-048D lower bushings are shipped wire tied

to Land Pride Skid Steer Quick Hitch. Place bushings over implement’s lower 7/8” hitch pins. This will provide a tighter and more secure mounting in the two lower Quick Hitch hooks. Do not use bushings when hitching to a Category II implement.

2. Make certain implement’s upper and lower hitch pins are secured.

3. Place Quick Hitch release handles in the down position as shown.

4. With arms of the skid steer loader lowered, carefully move loader up to (Cat. I or Cat. II) implement to align its upper and lower support hooks with implement’s 3-point hitch pins.

5. Slowly raise skid steer loader lift arms until lower Quick Hitch hooks lock over implement’s 3-point hitch pins.


Hook-Upe 1-3

Quick Hitch Bushing

Implement Linchpin

Implement’s Lower Hitch Pin

Standard Category I Connect Top Hook to Lower Center Hitch Pin/Bolt


Spare BushingsAdditional bushings may be purchased from your local Land Pride dealer so that more than one implement is readily available for quick hook-up.

IMPORTANT: Make certain implement’s top 3-point hitch pin is captured by the Quick Hitch top 3-point hook.

Lower BushingsPart No. Part Description

320-034A 2- Stepped Bushings CAT. l to CAT. lll Adapter320-048D Spacer Tube 1.44” O.D. x .91” I.D. x 1 9/32” lg320-044D Spacer Tube 1.44” O.D. x .93” I.D. x 1 5/8” lg.320-045D Spacer Tube 1.44” O.D. x .93” I.D. x 1 15/16” lg.320-050D Spacer Tube 1.44” O.D. x .93” I.D. x 2 3/16” lg.320-051D Spacer Tube 1.44” O.D. x .93” I.D. x 2 7/16” lg.325-017D Spacer Tube 1.44” O.D. x .93” I.D. x 3 15/16” lg.320-052D Spacer Tube 1.44” O.D. x .93” I.D. x 3 1/2” lg.


Release HandleFigur

Implement UnhookingRefer to Figure 1-4

! DANGERCrushing Hazard between Quick Hitch and Implement. Do not allow anyone to stand between Quick Hitch and implement while unhooking from implement. Never operate hydraulic lift controls while someone is directly behind the tractor.

! DANGEREngage parking brake, shut off skid steer loader, and remove key before dismounting.

1. Raise skid steer loader arms so implement is off the ground.

2. Engage park brake, shut engine off, and remove switch key before dismounting from loader.

3. Pull release handles up. See Figure 1-4.

4. Restart skid steer loader, lower loader arms until implement is on the ground, and Quick Hitch is clear of implement’s hitch pins.

5. Pull away from implement.

11/23/15

s Pointing Upe 1-4

22138

Section 2: Operating InstructionsTable of Contents

Section 2: Operating Instructions

Transporting and Use

! CAUTIONComply with all federal, state, and local laws when traveling on public roads.

! DANGERAlways use accessory lights and other available warning devices to alert other vehicle operators of your presence when traveling on public roads night and day.

! DANGERThe release handles should always be rotated down when using the Quick Hitch.

11/23/15

Operating InstructionsOnce you have familiarized yourself with the Operator’s Manual and properly attached your Land Pride SH35 Quick Hitch to the skid steer loader, you should be just about ready to start Quick Hitch “management and handling” of your compatible Category l and Category II 3-point implements.

You will notice we emphasize “management and handling” when we refer to your implements. If you are going to gain the benefit of owning a Land Pride SH35 Skid Steer Quick Hitch you will need to park your implements on a firm surface ensuring that the lower hitch pins and top-link remain upright or oriented for future Quick Hitch alignment and attachment. Allowing the lower hitch pins and top link to tumble forward into the dirt or mud will not be acceptable or compatible with this fast hook-up system. This simply is a better way to manage your time, your implements, and your investment.

Now you are ready to use your Quick Hitch. Put your Quick Hitch release handles in the down and locked position. Start your loader and slowly move forward centering on the implement you want to attach. Lower your three-point so the Quick Hitch lower hooks and top link hook line up under the implements lower hitch pins and top-link pin simultaneously. Slowly raise the Quick Hitch until all three pins are captured and the lower pins automatically lock in place. You should be ready for transport.

When you are ready to detach, position the implement over a firm surface or prepared docking point that will keep the lower hitch pins and top-link properly oriented for future attachment. With the implement still off the ground, set the parking brake, turn off the loader, remove the key, get off the loader, disconnect implement hydraulic hoses if used and raise the Quick Hitch release handles. Now get back on the loader, start the engine, slowly lower the implement until it is on the ground and the Quick Hitch releases. Slowly back-up until you are safely clear. With a little practice you should get very good at hooking and unhooking quickly.


Section 3: Maintenance & LubricationTable of Contents

Section 3: Maintenance & Lubrication

MaintenanceProper servicing and adjustments are key to the long life of any implement. With careful and systematic inspection, you can avoid costly maintenance, time, and repair.

After using your Skid Steer Quick Hitch for several hours, check all bolts to be sure they are tight.

Replace any worn, damaged, or illegible safety labels by obtaining new labels from your Land Pride dealer.

Lubrication


18443

AsRequired

50Hrs

Multi-purpose spray lube

Multi-purpose grease lube

Multi-purpose oil lube

Intervals in hours at whichlubrication is required

LubricationLegend

Pivot points

Multipurpose Spray Lube

Quantity = Generously

11/23/15

Section 4: Specifications & CapacitiesTable of Contents

Section 4: Specifications & Capacities


SH35 Series Skid Steer Quick Hitch

List Specifications & CapacitiesHitch Standard Category 1 & II, 3-point with adjustable top hitch

Overall Width 46 7/8”

Height 25”

Length 15 1/2”

Weight 225 lbs.

Lower 3-Point Automatic Lock

Maximum Lift Capacity 2,800 lbs at 24” from implements’, lower hitch pins.

26875

Section 5: Features & BenefitsTable of Contents

Section 5: Features & Benefits

12 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M 11/23/15

SH35 Series Skid Steer Quick Hitch

Features Benefits

Fits Cat. 1 or 2 implements Easily fits Cat. 1 or 2 non-PTO implements – Fits all Land Pride implements.

Automatic lock on lower 3-point arms

Don’t have to get off of skid steer loader when hooking up to an implement.

Adjustable top hook Helps match up to implement.

Class II receiver and storage for ball hitch

A class II ball hitch can be inserted into the hitch for towing, also can be used for storing a ball hitch.

Universal skid steer plate Fits most skid steer loaders.

Ball Hitch Receiver and Storage RackThe Quick Hitch is equipped so that a ball hitch can be assembled to the hitch. The Quick Hitch can then be used to pull an implement with a ball hitch. The ball hitch may be stored on top of the Quick Hitch when it is not in use.

Figure 4-118445

Section 6: Torque Values ChartTable of Contents

Section 6: Torque Values Chart


Torque Values Chart for Common Bolt SizesBolt Head Identification Bolt Head Identification

Bolt Size (inches) Grade 2 Grade 5 Grade 8

Bolt Size(Metric) Class 5.8 Class 8.8 Class 10.9

in-tpi 1 N · m 2 ft-lb 3 N · m ft-lb N · m ft-lb mm x pitch 4 N · m ft-lb N · m ft-lb N · m ft-lb

1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7

1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11

5/16" - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27

5/16" - 24 17 13 26 19 37 27 M 8 X 1 18 13 28 21 39 29

3/8" - 16 27 20 42 31 59 44 M10 X 1.5 33 24 52 39 72 53

3/8" - 24 31 22 47 35 67 49 M10 X 0.75 39 29 61 45 85 62

7/16" - 14 43 32 67 49 95 70 M12 X 1.75 58 42 91 67 125 93

7/16" - 20 49 36 75 55 105 78 M12 X 1.5 60 44 95 70 130 97

1/2" - 13 66 49 105 76 145 105 M12 X 1 90 66 105 77 145 105

1/2" - 20 75 55 115 85 165 120 M14 X 2 92 68 145 105 200 150

9/16" - 12 95 70 150 110 210 155 M14 X 1.5 99 73 155 115 l215 160

9/16" - 18 105 79 165 120 235 170 M16 X 2 145 105 225 165 315 230

5/8" - 11 130 97 205 150 285 210 M16 X 1.5 155 115 240 180 335 245

5/8" - 18 150 110 230 170 325 240 M18 X 2.5 195 145 310 230 405 300

3/4" - 10 235 170 360 265 510 375 M18 X 1.5 220 165 350 260 485 355

3/4" - 16 260 190 405 295 570 420 M20 X 2.5 280 205 440 325 610 450

7/8" - 9 225 165 585 430 820 605 M20 X 1.5 310 230 650 480 900 665

7/8" - 14 250 185 640 475 905 670 M24 X 3 480 355 760 560 1050 780

1" - 8 340 250 875 645 1230 910 M24 X 2 525 390 830 610 1150 845

1" - 12 370 275 955 705 1350 995 M30 X 3.5 960 705 1510 1120 2100 1550

1-1/8" - 7 480 355 1080 795 1750 1290 M30 X 2 1060 785 1680 1240 2320 1710

1-1/8" - 12 540 395 1210 890 1960 1440 M36 X 3.5 1730 1270 2650 1950 3660 2700

1-1/4" - 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220

1-1/4" - 12 750 555 1680 1240 2730 2010 1 in-tpi = nominal thread diameter in inches-threads per inch

1-3/8" - 6 890 655 1990 1470 3230 2380 2 N· m = newton-meters

1-3/8" - 12 1010 745 2270 1670 3680 2710 3 ft-lb= foot pounds

1-1/2" - 6 1180 870 2640 1950 4290 3160 4 mm x pitch = nominal thread diameter in millimeters x thread pitch1-1/2" - 12 1330 980 2970 2190 4820 3560

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

5.8 8.8 10.9

14 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M 11/23/15

Section 6: Torque Values ChartTable of Contents

Section 7: WarrantyTable of Contents

Section 7: Warranty


Warranty

Land Pride warrants to the original purchaser that this Land Pride product willbe free from defects in material and workmanship beginning on the date ofpurchase by the end user according to the following schedule when used asintended and under normal service and conditions for personal use.

Overall Unit and Driveline: One year Parts and Labor

This Warranty is limited to the repair or replacement of any defective part byLand Pride and the installation by the dealer of any such replacement part, anddoes not cover common wear items such as blades, belts, tines, etc. Land Pridereserves the right to inspect any equipment or parts which are claimed to havebeen defective in material or workmanship.

This Warranty does not apply to any part or product which in Land Pride’sjudgment shall have been misused or damaged by accident or lack of normalmaintenance or care, or which has been repaired or altered in a way whichadversely affects its performance or reliability, or which has been used for apurpose for which the product is not designed. Misuse also specifically includesfailure to properly maintain oil levels, grease points, and driveline shafts.

Claims under this Warranty must be made to the dealer which originally soldthe product and all warranty adjustments must be made through such dealer. LandPride reserves the right to make changes in materials or design of the product atany time without notice.

This Warranty shall not be interpreted to render Land Pride liable for damagesof any kind, direct, consequential, or contingent to property. Furthermore, LandPride shall not be liable for damages resulting from any cause beyond itsreasonable control. This Warranty does not extend to loss of crops, any expenseor loss for labor, supplies, rental machinery or for any other reason.

No other warranty of any kind whatsoever, express or implied, is madewith respect to this sale; and all implied warranties of merchantability andfitness for a particular purpose which exceed the obligations set forth in thiswritten warranty are hereby disclaimed and excluded from this sale.

This Warranty is not valid unless registered with Land Pride within 30 days fromthe date of purchase by the end user.

IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of purchase. This information is necessary to provide you with quality customer service.

Model Number ____________________ Serial Number ____________________

Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

www.landpride.com

Skid Steer Quick Hitch SH35 · 11/23/15 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M 1...

Documents

Transcript of Skid Steer Quick Hitch SH35 · 11/23/15 SH35 Category 1 & 2 Skid Steer Quick Hitch 320-019M 1...