SHED WINDOW INSTALLATION - Advance Metal …amia.com.au/wp-content/uploads/2012/03/Window...Detail 1...
2
SHED W INSTALLING WINDOW A: Refer to Step 1 on Installation Brochure. Measure and cut cladding to fit over Window Frame. e.g. for a 790x589 Window cut opening as shown Slot for Trim Bead (Head & Sill) to be cut as indicated. 5. Trim Bead Installation NOTE: Do n Sill Trim Be 800,0 A-A Install Trim Bead in the following o 1. Sill (refer Section A-A) Silicone Bead to be applied to Trim B after Trim Bead (Sill) has been installe before Trim Bead (Jambs) are installe Be careful to not obstruct Drain Holes B A B C ADDENDUM WINDOW INSTALLATI W TO VERTICAL CORRO PROF n not cut the 10x15mm angular corner aw ead pieces as shown in STEP 5 of the In CRITICAL DIMENSION 2,5 MIN. 789 ±0,50 2,5 MIN. 600,0 1 1 (Opp. Side) C- order: 2. Jambs 3. Head (refe Bead (Sill) Silicone Bead ed and (Head) after T ed. installed. with Silicone. B A C INTERIOR ION FILE CLADDING way from the Head or nstallation Brochure. 15 ±1 Detail 1 SLOTS TO BE CUT -C er Section C-C) d to be applied to Trim Bead Trim Bead (Head) has been B-B EXTERIOR
-
Upload
duongtuong -
Category
Documents
-
view
219 -
download
3
Transcript of SHED WINDOW INSTALLATION - Advance Metal …amia.com.au/wp-content/uploads/2012/03/Window...Detail 1...
SHED WINDOW INSTALLATION
INSTALLING WINDOW
A: Refer to Step 1 on
Installation Brochure.
Measure and cut cladding
to fit over Window Frame. e.g. for a 790x589 Window
cut opening as shown
Slot for Trim Bead
(Head & Sill) to be cut
as indicated.
5. Trim Bead Installation
NOTE: Do not
Sill Trim Bead pieces as shown in
80
0,0
A-A
Install Trim Bead in the following order:
1. Sill (refer Section A-A) Silicone Bead to be applied to Trim Bead (Sill)
after Trim Bead (Sill) has been installed and
before Trim Bead (Jambs) are installed
Be careful to not obstruct Drain Holes with Silicone.
B
A
B
C
ADDENDUM
SHED WINDOW INSTALLATION
INSTALLING WINDOW TO VERTICAL CORRO PROFILE CLADDING
Trim Bead Installation
not cut the 10x15mm angular corner away from the Head or
Sill Trim Bead pieces as shown in STEP 5 of the Installation Brochure
CR
ITIC
AL D
IME
NS
ION
2,5
MIN
.
78
9 ±
0,5
0
2,5
MIN
.
600,0
1
1
(Opp. Side)
C-following order:
2. Jambs 3. Head (refer Section C
be applied to Trim Bead (Sill) Silicone Bead
after Trim Bead (Sill) has been installed and (Head) after Trim Bead (Head) has be
Trim Bead (Jambs) are installed. installed.
Be careful to not obstruct Drain Holes with Silicone.
B
A
C
INT
ER
IOR
SHED WINDOW INSTALLATION
CORRO PROFILE CLADDING
cut the 10x15mm angular corner away from the Head or
of the Installation Brochure.
15 ±1
Detail 1
SLOTS TO BE CUT
-C
refer Section C-C)
Silicone Bead to be applied to Trim Bead
after Trim Bead (Head) has been
B-B
EX
TE
RIO
R
SHED WINDOW INSTALLATION
INSTALLING WINDOW TO
Waterproofing Recommendations Class 10 Buildings
In addition to already indicated, it is our recommendation as a minimum to install
For Class 10 Buildings
For
5. Trim Bead Installation
NOTE: Do not
Sill Trim Bead pieces as
Corrugated Foam Infill
Cut to length between Head
and Sill Trim Beads
(790mm for example given).
Install between FIN of Window Frame
and internal side of cladding
(both sides of window).
Install Trim Bead in the following order:
1. Sill Silicone Bead to be applied to Trim Bead (Sill)
after Trim Bead (Sill) has been installed and
before Trim Bead (Jambs) are installed
Be careful to not obstruct Drain Holes with Silicone.
ADDENDUM
SHED WINDOW INSTALLATION
TO HORIZONTAL CORRO PROFILE CLADDING
A: Refer to Step 1 on Installation Brochure.
Measure and cut cladding to fit over Window
Frame. e.g. for a 790x589 Window
Slot for Trim Bead (Head & Sill) to be cut.
Refer to Detail 1 on previous page.
Waterproofing Recommendations Class 1 Buildings
In addition to the Silicone beads already indicated, it is our recommendation as a minimum to install along jambs:
For Class 10 Buildings Corrugated Foam Infill
For Class 1 Buildings Corrugated Foam Infill +
Window Flashing.
Trim Bead Installation
not cut the 10x15mm angular corner away from the Head or
Sill Trim Bead pieces as shown in STEP 5 of the Installation Brochure
(to suit profile of cladding)
Cut to length between Head & Sill Trim Beads
(790mm for example given).
Flashing & foam should be installed prior to
window placem
applied along vertical length where flashing
Install Trim Bead in the following order:
2. Jambs 3. Head be applied to Trim Bead (Sill) Silicone Bead
rim Bead (Sill) has been installed and (Head) after Trim Bead (Head) has been
Trim Bead (Jambs) are installed. installed.
Be careful to not obstruct Drain Holes with Silicone.
INTERNAL FACE
Note:
Corrugated Foam and Window
Flashing are proprietary items and
are not supplied by AMIA
EXTERNAL FACE
SHED WINDOW INSTALLATION
CORRO PROFILE CLADDING
Refer to Step 1 on Installation Brochure.
Measure and cut cladding to fit over Window
e.g. for a 790x589 Window cut opening as shown
Trim Bead (Head & Sill) to be cut.
Refer to Detail 1 on previous page.
Class 1 Buildings
cut the 10x15mm angular corner away from the Head or
of the Installation Brochure.
Window Flashing
(to suit profile of cladding)
Cut to length between Head & Sill Trim Beads
(790mm for example given).
Flashing & foam should be installed prior to
window placement and a bead of silicone
applied along vertical length where flashing
meets cladding.
Silicone Bead to be applied to Trim Bead
after Trim Bead (Head) has been
INTERNAL FACE
INTERNAL SIDE OF WINDOW
EXTERNAL SIDE OF WINDOW
