8/13/2019 SEM712a_715aEnglishUserManual[1]

http://slidepdf.com/reader/full/sem712a715aenglishusermanual1 1/4

SEM712A/SEM715A Active 12” 2-Way Stage/Floor Speaker

 Active 15” 2-Way Stage/Floor Speaker

Safety Instructions

1. Read all instructions carefully before using your speakers

2. Keep this safety and instruction ier for future reference3. Ensure you follow all instructions carefully4. When used in conjunction with Ampliers or Powered Mixers

ensure you follow the correct procedures in the set up andturning on and off of audio equipment. It is advisable, whenan entire sound system is set up, that the power amplier orpowered mixer that you are using is turned on last (ie. Thatany source equipment, such as guitars, tape decks, etcetera,are turned on rst). After all source equipment is turned on andhave stabilized, ensure the power amp or powered mixer’s levelcontrol is set to a minimal level and then activate, after whichthe level control can be set to a reasonable level. This shouldbe done in reverse when shutting down: turn off the power ampor powered mixer rst, then turn off all other devices. Howevermany professional ampliers feature delayed on/off circuits thatcan perform this automatically.

5. Warning – These Speakers generate extremely high soundpressure levels. Ensure you take care in the placement and

operation to avoid exposure to extremely high sound levels, to

reduce to risk of causing permanent hearing damage.6. Cables – Under no circumstances should you use shielded or

microphone cables for connecting speakers to ampliers. Thesecables are not heavy enough to be able to handle the amplierload and could cause irreversible damage to your system.

7. Mounting – The suspending, rigging and mounting of theSpeakers can cause members of the public to be exposed toserious health risk, as well as the possibility of death. If youare NOT fully qualied and certied to mount these speakersby relevant local, state, or national authorities, do not underany circumstances try to rig, suspend or mount this system.

 All relevant safety regulations must be followed. If you are notcompletely qualied or do not know of said regulations, ensureyou consult qualied personnel for assistance.

8. Servicing – Do not under any circumstances try to service thisproduct by yourself. If servicing is required, contact your localservice center.

Features

l Double duty: use as a oor monitor or mounted as a

raised sound reinforcement speaker 

l Built-in amplier (RMS): 180 W

l Frequency response: 50 Hz - 20 khz

l High sound pressure level, 122 dB SPL @ 1W / 1M

l 15” heavy-duty woofer and piezo tweeter (SEM 715A)

l 12” heavy-duty woofer and piezo tweeter (SEM 712A)

l Built-in handle

l 35 mm stand adapter built-in

l 1/4” jacks & XLR inputs

l Link speakers through XLR output

Introduction

The SEM712A and SEM 715A Active Speakers are 2-way speak-

ers designed to accommodate professional applications that re-

quire both portability and impeccable sound quality. Both models

output up to 180 Watts (RMS) / 360 Watts (program) / 720 Watts

(peak), and feature XLR and 1/4” jacks for input of audio, as well

as an XLR output for linking of speakers. Where the two models

differ, however is that the SEM 712A features a 12” woofer and

piezo tweeter, whereas the SEM 715A features a 15" woofer and

piezo tweeter. Both models work as both raised sound reinforce-

ment speakers and oor monitors, depending on the necessary

application, and are enclosed in a black-carpeted casing.

PHONIC

8/13/2019 SEM712a_715aEnglishUserManual[1]

http://slidepdf.com/reader/full/sem712a715aenglishusermanual1 2/4

Specications

Suggested Setup Methods

Full Range System with Crossover 

Full Range System

SEM 712A SEM 715A

Type12” 2-way Stage/Floor Monitor

Speaker 

15” 2-way Stage/Floor Monitor

Speaker 

Built-in Amplier (Watts) RMS 180 180

Frequency Response 60 ~ 20 kHz 50 ~ 20 kHz

Max SPL @ 1 W / 1 M 120 dB 122 dB

Built-in Crossover  Yes Yes

Dispersion Angle (Degrees) 90 x 40 90 x 40

Box N/A N/A

Appearance Black Carpet Black Carpet

Handles 2 2

Stand Socket 35mm 35mm

Connector  XLR + 1/4” phone jacks XLR + 1/4” phone jacks

Dimensions cm/in. (HxWxD) 540 x 376 x 356 mm (21.3” x 14.8”x 14.0”)

679 x 476 x 388 mm (26.7” x 18.7”x 15.3”)

Net Weight >13 kg >19 kg

8/13/2019 SEM712a_715aEnglishUserManual[1]

http://slidepdf.com/reader/full/sem712a715aenglishusermanual1 3/4

6103 Johns Road #7

8/13/2019 SEM712a_715aEnglishUserManual[1]

http://slidepdf.com/reader/full/sem712a715aenglishusermanual1 4/4