Selective Mechanization in Rice Cultivation for Energy...

Page | 1

For more Information contact: Visit Rice Knowledge Management Portal http://www.rkmp.co.in

Rice Knowledge Management Portal (RKMP)

Directorate of Rice Research,

Rajendranagar, Hyderabad 500030. Email: [email protected], [email protected], [email protected]

Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Selective Mechanization in Rice Cultivation for Energy Saving and

Enhancing the Profitability

T. Vidhan Singh1, R. Mahender Kumar

2 and B.C.Viraktamath

3

1. Senior Scientist, Agril. Engineering,

2. Principal Scientist, Agronomy

3. Project Director

Directorate of Rice Research, Rajendranagar – Hyderabad-500 030

Page | 2





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Introduction

Rice is cultivated in 44 million ha in India and is largest area in the world. During the past

55 years there has been a remarkable increase in the production of rice. The area under rice

increased by 1.5 times while the production increased by over four times to the tune of 99 million

tones. The productivity has increased from 0. 7 t/ha to 2.40 t/ha. To mitigate the growing

population rate rice production should rise to 120 million tones by 2020. This could be achieved

only through selective mechanization and increase of productivity as the area is plateaued.

With depleting natural resources, deteriorating soil health and declining input use

efficiency achieving the target of 120 million tones is an uphill task. Increase in rice production is

achieved mainly due to the improvement of irrigation facilities, introduction of high yielding

varieties and judicious use of critical inputs. Agricultural mechanization is one critical input which

not only facilitates timely completion of operations and thereby increases the production, labour

saving, energy efficiency, productivity and profitability.

Benefits of Mechanization

An expert committee on the agricultural mechanization observed that the productivity is

influenced by mechanization as follows:

1. 5-10% improvement in yield by proper and timely seed bed.

2. 5-30% improvement in yield by efficient control of weeds.

3. Reduces losses by 4-5% through efficient harvesting and threshing.

4. 8 –10% losses reduction by proper post harvest process and storage.

5. Upto 2.5 per cent increase in head rice recovery by efficient milling. .

Page | 3





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Labour saving

Rice is a labour intensive crop. About 850 to 900 man hours of labour is required for cultivating

one hectare. The following table gives the operation wise labour requirement in rice cultivation.

S.No. Operations Percentage of total labour

requirement

1. Puddling 11

2. Transplanting 38

3. Weeding 19

4. Harvesting 20

5. Threshing 12

Transplanting, weeding and harvesting operations consume most of the labour

requirement in rice cultivation and hence thrust should be given for this mechanizing these

operations in order to reduce the labour requirement in rice cultivation. High labor demand

during peak periods adversely affects timeliness of operation, thereby reducing the crop yield.

The steady drift of agricultural labor to industrial sector is adding more to the woes of the rice

farmer. Because of drudgery and notion that the farm operations are below the dignity, labor

availability, in general, has decreased considerably to farm operations. To offset these problems

stress on mechanization is the need of the hour.

Energy in agriculture.

The power consumption for agriculture in developed countries is 3-5 times higher than

what we consume in India. Farm power availability should be raised to 2 – 2.5 KW/ha from the

present 1.15 KW/ha for achieving targeted level of mechanization.

Page | 4





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Percent mechanization of rice production operation

Percent mechanization of field operations

Land

preparati

on

Nursery

raising &

Trans-

planting

Fertilizer

application

Spraying Harvesting Threshing Irrigation

by pump

60 00 25 100 3 20 50

It is satisfying to note that almost all the operations of rice production viz., land

preparation, irrigation and plant protection attained the desired level of mechanization. However

transplanting and harvesting are yet to be fully mechanized to attain the desired level of power

utilization and to ease the rice cultivation

Relief from drudgery:

Farm women contribute significant labour input in various operations of rice cultivation.

The following table gives percentage of women labour contribution in various of rice cultivation.

Sl No. Operation Per cent input

1 Transplanting 80

2 Weeding 80

3 Harvesting 60

Page | 5





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Transplanting, weeding and harvesting are done in the bending posture resulting in spinal

cord related health problems in women.

Reducing cost of cultivation

After the advent of WTA there is every need of competing with the other rice growing

countries and as a result reducing the cost of cultivation takes top priority. Cost of cultivation

could be reduced by using alternatives techniques like direct sowing. There is also every need

to increase the input use efficiency. Placement of urea at appropriate place reduces

volatilization and leaching losses and thereby saving urea up to 30 per cent without

compromising on the yield level.

Constraints of Mechanization of rice farming

Smaller land holding is one of the major constraints for mechanized farming in India. In

India 78.2% of farmers hold cultivable area upto 2 ha.(1990-91)

Number and area of operational holdings by type of holding

Major Size

Classes

Number Area

1980-81 1990-91 1980-81 1990-91

Marginal

(below 1 ha)

50,122

(56.4)

63,389

(59.4)

19,735

(12.0)

24,894

(15.1)

Small

(1 to 2 ha)

16,072

(18.1)

20,092

(18.8)

23,169

(14.2)

28,827

(17.4)

(Figures in parenthesis indicate percentage contribution.)

Page | 6





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

The fragmentation of land holdings limits the free movement of the machinery. This results in loss

of time in turning. It is feared in certain quarters that there will be labour displacement due to

mechanization. Poor investment capacitiy of small and marginal farmers to purchase the

machinery and lack of after sales and services restrict the spread of mechanization. Considering

these aspects, there is a need to adopt selective mechanization to benefit all kinds of farmers.

Improved farm implements and machinery for rice cultivation:

A) Land Preparation Equipment

Puddling is the most important operation in the preparation of soil bed for transplanting rice. The

soil physical properties like soil structure, viscosity, bulk density etc changes due to puddling.

Puddling creates an impervious layer and this assists in reducing the deep percolation losses.

Prerequisite for puddling is preparatory dry tillage.

The indigenous plough is the most prevalent implement used as a puddler in spite of its

poor efficiency. An indigenous plough can cover only about 0.15 ha/day. There are several animal

drawn and power operated puddlers developed in India. Among the power operated puddlers,

power tillers and tractors are popular.

A.P.A.U. Puddler: It is a bullock drawn implement. With the movement of the bullocks, the shaft

rotates the blades, which in turn churn the soil. It is suitable for all types of soils. It is advisable to

puddle the soil twice or thrice. The implement set up has provision for seat for the operator.

Cono puddler: The puddler utilizes a new concept of conical shaped rotors for puddling in soft

paddy soil.

Page | 7





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Cono puddler

It operates in the soil in a horizontal back and forth movement. It can be operated in all types of

soils since this is a lightweight and modular implement.

Power tiller: It is a 12 hp self propelled machine specifically useful for rice fields and orchards as it

can take short turns. It comes with a package of implements like rotavator for puddling, cultivator

for land preparation. It can be used for operations like pumping, threshing and for farm transport.

It takes about 5h to puddle one hectare. Its cost is approximately 1 to 1.5 lakh rupees.

Tractor: Tractors are available in two power ranges. Small power range tractor with 18 HP is

meant for rice cultivation. It is a lightweight tractor with four wheel drive with rotavator used for

puddling. It has a small turning radius. Trafficability problem can be avoided with this tractor due

to its light weight. It can puddle one hectare in 2.5-3h.

B) Seeding and planting Equipment

Direct sowing Row seeder: A row seeder (also known as drum seeder) sows the

pregerminated paddy seeds in the rows at spacing of 20 cm in puddle soil. There is saving in the

cost of cultivation to the tune of 35 per cent by using this device.

Page | 8





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

DRR 8 Row Drum Seeder

The advantages of the machine are

• Lightness of the machine, • Ease of operation with one operator,

• Ease of fabrication at any local workshop, • Low cost,

Direct sowing Row seeder with wider spacing ( 25 cm X 25 cm) SRI - drumseeder: A row

seeder (with a spacing of 25 cm row to row ) sows the pregerminated paddy seeds in the rows at a

spacing of 25 cm in puddle soil. The other principles of SRI can be well adopted with this seeder to

enhance the productivity. The drum seeder is under testing at DRR to save seed and enhance

profitability

6 row drum seeder (SRI drum seeder )

8-Row paddy transplanter (Chinese design): It is a self-propelled machine driven by 3 - 4 hp diesel

engine. The machine transplants at a row spacing of 23 cm with a provision to vary the plant to

plant distance of 10 - 12 cm and vary the depth of planting and number of plants per hill. It

requires mat type nursery. DRR has standardized the size of the mats to be used with this

Page | 9





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

transplanter and developed a suitable frame to prepare the mats, which saves labor in nursery

preparing and cutting of mats and ensures uniformity of seedling density over mats. The machine

can cover about 0.8 ha in a day with a net saving in labor of about 40 per cent. The machine is

more suitable for light textured soils. Further at present , the mechanical transplanters can plant

2 seedlings per hill at a spacing of 24 cm ( row to row ) and 12- 24 cm ( plant to plant) for

adoption of other SRI principles. This will be a very good development in promoting SRI in large

scale.

Chinese model of transplanter Korean model of transplanter

C) Weeding Equipments

Weeds are serious menace to crops as they reduce the yields and farmers income as they

affect crop growth and development in many ways. . Problems associated with weeds can be

enumerated as

• Reduction in yield and quality

• .Increase problems with pest and diseases

Page | 10





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

.

Cono weeder

Weeding requires 120 man hours per hectare. Most work on weeding emphasizes on the

timeliness of operation. Timeliness is the key factor for successful and effective weeding. System

of Rice intensification is paddy cultivation using less seed, less water and less fertilizer. This system

encourages farmer participation and innovation to make it more appropriate to local conditions

and more owned by the users.

Weeding Process in SRI:

In SRI, first weeding is done after 10-12days of transplantation. Subsequently weedings are done

every 10days, until the crop permits operation. Weeding at 10day interval is necessary. The field is

irrigated one day before weeding and atleast half inch water is retained for easy operation.

Weeder is moved front and back between every two rows both vertically and horizontally.

Mechanical weeding alone increased the plant height and enhanced the grain yield by 10.9% as

compared to manual weeding.

Page | 11





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Different types of weeders used in SRI

Tamil Nadu Weeder Single drum weeder

Four Row Weeder Nepali Terai Weeder

Jharkand Weeder

Srilanka Weeder

Tefy Saina Weeder Cambodia Weeder

Mechanized Weeder

Adjustable tow row weeder

Rotating hoe Rotary weeder, Northern India

Cuba weeder

Ariyaratna motorized weeder

Cono Weeder, IRRI design Mandava – Single Row weeder

Mandava – Two Row Weeder

Star (Tarimella) Row Weeder

Kollur Weeder

Three Row Raichur Weeder

KVK Weeder Japan Weeder

English Weeder

Mad double cono-weeder

ATS weeder Rotating hoe – Srilanka and Madagascar

4 Row Weeder – Gopal,

TN Senegal weeder

Wolf-fang weeder Rotating hoe (China)

Use of appropriate weeding equipments coupled with suitable weedicide gives the best results

against weeds. Cono weeder can be used as a package implement for row seeder and extensively

used in the SRI type of cultivation

Page | 12





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

D) Harvesting Equipment

Delayed harvesting due to non availability of labours will lead to yield losses on account of

shattering. Various equipments used for harvesting are as follows

Sickles: In the improved sickles the cutting edge is serrated instead of being plain. The serrated

edged blades facilitate self sharpening and better quality of cut. The handles are made light with a

better grip to improve the operators comfort. Some of the commercially available sickles are

'MAIDC', 'Vaibhav' and 'Naveen'. These sickles harvest 17% more area in a given time in

comparison with traditional sickles

Vertical conveyor reaper: Vertical conveyor reaper (VCR) harvests and windrows the crop to

one side. This augurs well with the farmers' practice where the paddy is left in the field for some

time for proper drying. One of the commercial models available in the market is operated with 3

hp petrol start- kerosene run engine.

It has better maneuverability in the field.

It can harvest about half an acre in one hour. The fuel consumption is only 2 liters of

kerosene/acre. The shattering losses are also minimized. The machine is fully commercialized

Page | 13





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Combine Harvester:

This is self propelled (105 bhp at 2200 rpm) machine which cuts, conveys, threshes, cleans and

bags the produce from the field.. It can harvest even a lodged crop. Wheel and chain

combines are available. The chain combine is having more maneuverability by having lesser

turning radius. It has working width of about 4.2m. It can harvest 0.8-1.2 ha/h of paddy. The

straw disposal and utilization seems to be problematic with the use of combines.

E) Threshing Equipment:

Traditionally threshing is done by treading by bullocks or trampling by tractors. It takes more time

and loss of yield through unthreshed paddy is more. This has been replaced by power operated

threshers of 5 to 15 HP with either diesel or electrical power driven source.

Pedal Operated Thresher It consists of wire-loop type threshing cylinder operated by foot pedal.

It is suitable for threshing rice. It saves 20 percent labour and 40 per cent operating time

compared to conventional method of hand beating on a wooden platform.

Pedal operated thresher Multicrop thresher

Page | 14





Ph: 91-40-24591218, 295 Fax: 91-40-24591217

Technical Specifications of threshers

S.No. Equipment Developed at Power source Total

Weight

(Kgs)

Output

Capacity

(Kg/h)

1. Pedal Thresher IIT, Kharagpur Two persons 36 44

2. Portable rice

thresher

CIAE-IEP

Coimbatore

3 hp motor

5 hp engine

100 100

3 Axial flow multicrop

thresher

GBPUAT,

Pantnagar

25 to 30 hp

tractor

500 1200-312

4. Axial flow rice

thresher

PAU,

Ludhiana

35 hp tractor 730 1300

5. Plot thresher CIAE,

Bhopal

1 hp motor 120 6.5-35.2

6. Multicrop thresher APAU, 5 hp motor 350 350

Conclusions:

Carrying out timely operation and reducing cost of cultivation is the prerequisite for

enhancing the production and productivity of rice and as well as to make rice cultivation

commercially viable and profitable enterprise for the farmers. Selective mechanization can

help to achieve this goal. There is a need to develop suitable weeders for different soil

conditions especially row planted (SRI cultivation) and motorization of the weeder will help for

large scale adoption. The effective utilization of inputs like irrigation water and fertilizer is a

necessity. Reducing losses while in operation of various activities of rice production and

reduction of post harvest losses is essential.

Selective Mechanization in Rice Cultivation for Energy...

Documents

Transcript of Selective Mechanization in Rice Cultivation for Energy...