SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 CALIBRATION · (A2LA Cert. No. 2357.15) Revised...

(A2LA Cert. No. 2357.15) Revised 01/28/2016 of 27

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

& ANSI/NCSL Z540-1-1994

TEKTRONIX SERVICE SOLUTIONS 24301 Catherine Industrial Road, Suite 116

Novi, MI 48375 Rob Ciolino Phone: 248 305 5200

CALIBRATION

Valid to: December 31, 2017 Certificate Number: 2357.15 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations1: I. Chemical Quantities

Parameter/Equipment

Range CMC2 ()

Comments

pH3 Meters

4.01 pH 7.00 pH 10.0 pH

0.049 pH 0.031 pH 0.036 pH

Standard solutions

Conductivity Meters3

(1 to 10) µS (10 to 100) µS (100 to 1000) µS (1 to 20) mS

0.26 µS 1.0 µS 5.4 µS 0.067 mS

Standard solutions

II. Dimensional

Parameter/Equipment

Range CMC2, 5 ()

Comments

Micrometers

(0.05 to 4) in (4 to 12) in (12 to 48) in

(64 + 0.25L) µin (100 + 10L) µin (170 + 19.6L) µin

Grade 2 gage blocks

Calipers3

(0.05 to 4) in (4 to 12) in (12 to 48) in

(64 + 0.25L) µin (90 + 10L) µin (170 + 13L) µin

Grade 2 gage blocks


Parameter/Equipment

Range CMC2 ()

Comments

Length Indicators3 Up to 3 in

68 µin

Grade 1 gage blocks

Height Gages, & Depth Gages3

Up to 12 in (12 to 40) in

110 µin 320 µin

Grade 2 gage blocks

Surface Plate Flatness3

Up to 96 in 48 in 71 µin

Rahn 24-inch planekator

Rulers3

Up to 48 in 9000 µin

Gage blocks

Protractors, Inclinometers & Levels3

0 to 150

170 arc seconds

Sine plate and gage blocks

Angle3

1º 3º 5º 15º 30º 45º

0.00080º 0.00082º 0.00082º 0.00080º 0.00080º 0.00082º

Angle blocks

Surface Flatness3

Up to 24 in 4 µin

Mitutoyo Mu checker w/ head and gage blocks

Pins and Plugs3

Up to 1 in

16 µin

Lasermic w/ master pins

Threaded Plugs3 –

Pitch Diameter

Up to 3 in OD

77 µin

SIP machine

Extensometers3

Length/Displacement

Up to 0.5 in 0.5 to 50 in

31 µin 0.080 in

SIP machine red lion controls PAXI


III. Electrical – DC/Low Frequency

Parameter/Equipment

Range

CMC2, 4 ()

Comments

DC Voltage – Generate3

Up to 220 mV (0.22 to 2.2) V (2.2 to 11) V (11 to 22) V (22 to 220) V (220 to 1100) V 10 V 1.018 V 1.000 V

7.1 µV/V + 0.5 µV 6.5 µV/V 3.4 µV/V 3.3 µV/V 4.9 µV/V 6.6 µV/V 2.2 µV/V 7.7 µV/V 2.2 µV/V

Fluke 5720A Fluke 5720A Fluke 732A

DC Voltage – Measure3

Up to 200 mV (0.2 to 2) V (2 to 20) V (20 to 200) V (200 to 1050) V (1.1 to 40) kV

6.1 µV/V + 0.12 µV 3.0 µV/V 3.8 µV/V 3.8 µV/V 5.2µV/V 26 V

Fluke 8508A Fluke 80K40

DC Current – Generate3

Clamp-On Only

(0 to 2) pA (2 to 20) pA (20 to 200) pA (0.2 to 2) nA (2 to 20) nA (20 to 200) nA (0.2 to 2) A (0.1 to 220) A (0.22 to 2.2) mA (2.2 to 22) mA (22 to 220) mA (0.22 to 2.2) A (2.2 to 11) A (11 to 20.5) A (16.5 to 149.999) A (150 to 1025) A

1.3 mA/A + 0.40 fA 0.84 mA/A + 4.0 fA 0.59 mA/A + 40 fA 0.34 mA/A + 40 fA 0.34 mA/A + 25 fA 0.34 mA/A + 7.0 fA 0.34 mA/A + 4.0 fA 41 µA/A + 7.0 nA 35 µA/A 34 µA/A 43 µA/A 76 µA/A 0.32 mA/A 0.82 mA/A 0.60 % 0.56 %

Fluke 5720A w/ Keithley 5156 Fluke 5720A w/ 5725A Fluke 5520A Fluke 5520A w/5500A/ Coil

DC Power– Generate3

(0.01 to 330) W (0.33 to 2.9) kW (3.0 to 20.5) kW

0.24 mW/W 0.18 mW/W 0.56 mW/W

Fluke 5520A


Parameter/Equipment

Range

CMC2, 4 ()

Comments

DC Current – Measure3

(0 to 200) A (0.2 to 20) mA (2 to 20) mA (20 to 200) mA (0.2 to 2) A (2 to 20) A (20 to 300) A (100 to 1000) A

14 µA/A+ 0.4 nA 15 µA/A 16 µA/A 51 µA/A 0.18 mA/A 0.42 mA/A 0.53 mA/A 0.25 %

Fluke 8508A 8508A w/ L&N 4361 shunt

Empro E1500 100

DC Resistance – Generate3

Fixed Points

(0 to 11) (11 to 33) (33 to 110) (110 to 330) (.33 to 1.1) k (1.1 to 3.3) k (3.3 to 11) k (11 to 33) k (33 to 110) k (110 to 330) k (.33 to 1.1) M (1.1 to 3.3) M (3.3 to 11) M (11 to 33) M (33 to 110) M (110 to 330) M (330 to 1100) M 1 k 10 k 100 k 1 M 10M 100 M 1 G 10 G 100 G 10 M 100 M 1000 M

44 µΩ/Ω + 1.0 mΩ 14 µΩ/Ω + 1.5 mΩ 34 µΩ/Ω 32 µΩ/Ω 33 µΩ/Ω 30 µΩ/Ω 26 µΩ/Ω 27 µΩ/Ω 26 µΩ/Ω 36 µΩ/Ω 30 µΩ/Ω 57 µΩ/Ω 0.12 mΩ/Ω 0.30 mΩ/Ω 0.55 mΩ/Ω 3.7 mΩ/Ω 13 mΩ/Ω 14 m 0.19 1.7 22 0.72 k 0.062 M 0.24 M 7.1 M 0.095 G 0.83 k 100 k 1.1 M

Fluke 5520A Biddle megadek PPM R3-1, 110M


Parameter/Equipment

Range CMC2,4 ()

Comments

DC Resistance – Generate3 (cont)

Fixed Values

0.01 0.1 0.001 1 1.9 10 19 100 190 1 k 1.9 k 10 k 19 k 100 k 190 k 1 M 1.9 M 10 M 19 M 100 M

0.41µΩ 4.2 µΩ 0.041 µΩ 7.0 µΩ 0.19 m 0.24 m 0.48 m 1.1 m 1.9 m 7.9 m 16 m 37 mΩ 0.15 1.0 2.7 50 60 4.0 k 8.5 k 26 k

L&N 4361 L&N 4360 L&N 4363 Fluke 742A-1 Fluke 5720A Fluke 742A-10K Fluke 5720A

DC Resistance – Measure3

(0 to 2) (2 to 20) (20 to 200) (0.2 to 2) k (2 to 20) k (20 to 200) k (0.2 to 2) M (2 to 20) M (20 to 200) M (0.2 to 2) G

19 µ/ + 5 µ 10 µ/ 8.2 µ/ 8.1 µ/ 8.2 µ/ 8.2 µ/ 11 µ/ 49 µ/ 81 µ/ 0.25 m/

Fluke 8508A

Rise Time – Generate3

< 300 pS 8.4 ps

Fluke 5520A-SC1100

Rise Time – Measure3

<350 pS 8.4 ps

TDS 684A


Parameter/Equipment

Range CMC2, 4 ()

Comments

Leveled Sinewave Flatness3

(Reference to 50 kHz)

50 kHz to 100 MHz (100 to 300) MHz (300 to 600) MHz (600 to 1100) MHz

18 mV/V + 100 µV 21 mV/V + 100 µV 34 mV/V + 100 µV 42 mV/V + 100 µV

Fluke 5520A-SC1100

AC Voltage – Generate3

(0.2 to 2.2) mV (1 to 22) mV (22 to 220) mV (0.22 to 2.2) V

(10 to 20) Hz (20 to 40) Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 300) kHz (300 to 500) kHz (0.5 to 1) MHz (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 300) kHz (300 to 500) kHz (0.5 to 1) MHz (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 300) kHz (300 to 500) kHz (0.5 to 1) MHz (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 300) kHz (300 to 500) kHz (0.5 to 1) MHz

2.2 mV/V + 4.0 µV 1.3 mV/V + 4.0 µV 0.099 % + 4.0 µV 1.7 mV/V + 4.0 µV 2.3 mV/V + 0.0 µV 4.1 mV/V + 10 µV 6.5 mV/V + 20 µV 8.5 mV/V + 20 µV 0.038 % + 5 µV 0.022 %+ 5 µV 0.026 % + 5 µV 0.038 % + 5 µV 0.066 % + 7 µV 1.5 mV/V + 12 µV 1.9 mV/V + 25 µV 3.4 mV/V + 25 µV 0.026 % + 15µV 0.01 % + 8 µV 94 µV/V + 8 µV 0.021 % + 8 µV 0.05 % + 20 µV 0.09 % + 25 µV 1.4 mV/V + 30 µV 2.8 mV/V + 60 µV 0.024 % + 50 µV 90 µV/V + 20 µV 50 µV/V + 10 µV 85 µV/V + 12 µV 0.013 % + 40 µV 0.042 % + 100 µV 0.097 % + 250 µV 1.8 mV/V + 400 µV

Fluke 5720A w/wideband Fluke 5720A


Parameter/Range Frequency CMC2, 4 ()

Comments

AC Voltage – Generate3 (cont)

(2.2 to 22) V

(22 to 220) V

(200 to 1100) V

(220 to 750) V

(220 to 1100) V

(10 to 20) Hz (20 to 40) Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 300) kHz (300 to 500) kHz (0.5 to 1) MHz (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 kHz (20 to 50) kHz (50 to 100) kHz (100 to 300) kHz (300 to 500) kHz (0.5 to 1) MHz (15 to 50) Hz 50 Hz to 1 kHz 30 kHz to 50 kHz (50 to 100) kHz 40 Hz to 1 kHz (1 to 20) kHz (20 to 30) kHz

0.024 % + 500 µV 91 µV/V + 200 µV 50 µV/V + 70 µV 87 µV/V + 120 µV 0.013 % + 250 µV 0.032 % + 800 µV 1.0 mV/V + 2.5 mV 1.9 mV/V + 4.0 mV 0.025 % + 5 mV 93 µV/V + 2 mV 63 µV/V + 0.7 mV 0.011 % + 1.2 mV 0.017 % + 3 mV 0.086 % + 20 mV 4.2 mV/V + 50 mV 7.8 mV/V + 100 mV 0.028 % + 20 mV 77 µV/V + 4 mV 0.062 % + 11 mV 2.4 mV/V + 45 mV 98 µV/V + 4 mV 0.017 % + 6 mV 0.062 % + 11 mV

Fluke 5720A Fluke 5720 w/5725A

AC Voltage – Measure3

(0 to 200) mV

(10 to 40) Hz (40 to 100) Hz (0.1 to 2) kHz (2 to 10) kHz (10 to 30) kHz (30 to 100) kHz

0.016 % + 5 µV 0.012 % + 5 µV 0.013 % + 2 µV 0.015 % + 5 µV 0.034 % + 10 µV 0.074 % + 24 µV

Fluke 8508A


Parameter/Range Frequency CMC2, 4 () Comments

AC Voltage – Measure3

(cont)

(0.2 to 2) V

(2 to 20) V

(20 to 200) V (300 to 1050) V

(10 to 40) Hz (40 to 100) Hz (0.1 to 2) kHz (2 to 10) kHz (10 to 30) kHz (30 to 100) kHz (100 to 300) kHz (0.3 to 1) MHz (10 to 40) Hz (40 to 100) Hz (0.1 to 2) kHz (2 to 10) kHz (10 to 30) kHz (30 to 100) kHz (100 to 300) kHz (0.3 to 1) MHz (10 to 40) Hz (40 to 100) Hz (0.1 to 2) kHz (2 to 10) kHz (10 to 30) kHz (30 to 100) kHz (100 to 300) kHz (0.3 to 1) MHz (10 to 40) Hz (0.04 to 10) kHz (10 to 20) kHz (20 to 100) kHz

0.012 % + 24 µV 0.012 % + 24 µV 80 µV/V + 24 µV 0.012 % + 24 µV 0.023 % + 50 µV 0.057 % + 240 µV 2.6 mV/V + 2.4 mV 8.5 mV/V + 24 mV 0.013 % + 1.4 mV 99 µV/V + 0.24 mV 81 µV/V + 0.24 mV 0.012 % + 0.24 mV 0.022 % + 0.50 mV 0.056 % + 2.4 mV 2.6 mV/V + 24 mV 8.5 mV/V + 240 mV 0.017 % + 2.4 mV 0.011 % + 2.4 mV 90 µV/V + 2.4 mV 0.012 % + 2.4 mV 22 µV/V + 2.4 mV 0.056 % + 5 mV 2.5 nV/V + 240 mV 8.5 nV/V + 2.4 V 0.014 % + 80 mV 12 µV/V + 25 mV 0.023 % + 40 mV 0.059 % + 200 mV

Fluke 8508A

AC Current – Generate3

(9 to 220) A

(10 to 20) Hz (20 to 40) Hz 40 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz

0.026 % + 16 nA 0.017 % + 10 nA 0.013 % + 8 nA 0.029 % + 12 nA 1.2 mA/A + 65 nA

Fluke 5720A w/ 5725A



AC Current – Generate3 (cont)

(0.22 to 2.2) mA (2.2 to 22) mA

(22 to 220) mA (0.22 to 2.2) A (2.2 to 11) A (11 to 20.5) A Clamp-On Only (16.5 to 149.999) A (16.5 to 149.999) A (150 to 1025) A (150 to 1025) A

(10 to 20) Hz (20 to 40) Hz 40 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (10 to 20) Hz (20 to 40) Hz 40 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (10 to 20) Hz (20 to 40) Hz 40 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz 20 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz 40 Hz to 1 kHz (1 to 5) kHz (5 to 10) kHz (45 to 100) Hz (0.1 to 1) kHz (1 to 5) kHz (45 to 65) Hz (65 to 440) Hz (45 to 65) Hz (65 to 440) Hz

0.026 % + 40 nA 0.017 % + 35 nA 0.013 % + 35 nA 0.021 % + 110 nA 1.2 nA/A + 650 nA 0.026 % + 40 nA 0.017 % + 350 nA 0.013 % + 350 nA 0.021 % + 550 nA 1.5 nA/A + 5.0 µA 0.026 % + 4 µA 0.017 % + 3.5 µA 0.013 % + 2.5 µA 0.021 % + 3.5 µA 1.2 nA/A + 10 µA 0.027 % + 35 µA 0.047 % + 80 µA 7.3 nA/A + 160 µA 0.048 % + 170 µA 0.099 % + 380 µA 3.8 nA/A + 750 µA 1.1 mA/A + 5 mA 1.3 mA/A+ 5 mA 23 mA/A + 5 mA 0.68 % 1.0 % 0.32 % 0.81 %

Fluke 5720A w/ 5725A Fluke 5520A Fluke 5520A w/5500A/ coil Fluke 5520A w/5500A/ coil



AC Current – Measure3

Up to 200 A (0.2 to 2) mA

(2 to 20) mA (20 to 200) mA

(0.2 to 2) A

(2 to 20) A

10 Hz to 10 kHz (10 to 30) kHz (30 to 100) kHz 10 Hz to 10 kHz (10 to 30) kHz (30 to 100) kHz 10 Hz to 10 kHz (10 to 30) kHz (30 to 100) kHz 10 Hz to 10 kHz (10 to 30) kHz 10 Hz to 2 kHz (2 to 10) kHz (10 to 30) kHz 10 Hz to 2 kHz (2 to 10) kHz

0.038 % + 24 nA 0.038 % + 24 nA 3.4 nA/A + 24 nA 0.034 % + 0.24 µA 0.074 % + 0.24 µA 3.4 nA/A + 0.24 µA 0.033 % + 2.4 µA 0.069 % + 2.4 µA 4.1 nA/A + 2.4 µA 0.031 % + 24 µA 0.074 % + 24 µA 0.062 % + 0.24 mA 0.075 % + 0.24 mA 2.5 nA/A + 0.24 mA 0.078 % + 2.4 mA 2.1 nA/A + 2.4 mA

Fluke 8508A

AC Power – Generate3

(0.01 to 0.1) W (0.1 to 890) W (0.89 to 3) kW (3 to 11) kW (11 to 20.5) kW

(45 to 65) Hz, PF = 1

1.6 mW/W 1.1 mW/W 0.9 mW/W 0.78 mW/W 0.78 mW/W

Fluke 5520A

AC Level Flatness – Generate3

(0.45, 3, 6) V

10 Hz 100 Hz 10 kHz 30 kHz 100 kHz 300 kHz 1 MHz 3 MHz

5.1 mV/V 2.1 mV/V 2.1 mV/V 2.5 mV/V 3.1 mV/V 6.7 mV/V 4.2 mV/V 9.1 mV/V

Thermal converters EL1100 and 1395A w/ HP 3458A and Fluke 5700A


Parameter/Range

Frequency CMC2, 4 ()

Comments

AC Level Flatness – Generate3 (cont)

(0.45, 3, 6) V

8 MHz 10 MHz 20 MHz 30 MHz 50 MHz 70 MHz 80 MHz 100 MHz

9.1 mV/V 1.0 mV/V 1.6 mV/V 2.2 mV/V 4.4 mV/V 16 mV/V 17 mV/V 17 mV/V

Thermal converters EL1100 and 1395A w/ HP 3458A and Fluke 5700A

AC Resistance – Generate3

Fixed Values

10 100 1 k 10 k 100 k

DC to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz DC to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz DC to 3 MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz DC to 1 MHz DC to 1 MHz

5.2 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 4.3 mΩ/Ω 5.2 mΩ/Ω 5.9 mΩ/Ω 6.6 mΩ/Ω 2.0 mΩ/Ω 3.0 mΩ/Ω 5.2 mΩ/Ω 5.2 mΩ/Ω

HP 42030 resistor set



Comments

Capacitance – Generate3

Fixed Values 1 pF 10 pF 100 pF 1000 pF (10, 100) nF 1 F

100 Hz to 1 kHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 100 Hz to 1 kHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 100 Hz to 1 kHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 100 Hz to 1 kHz 1 kHz to 1 MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz (100 to 120) Hz 120 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz (100 to 120) Hz 120 Hz to 1 kHz (1 to 10) kHz (10 to 100) kHz

7.1 µF/F 7.1 µF/F 7.4 µF/F 8.2 µF/F 9.5 µF/F 1.1 µF/F 2.6 µF/F 3.8 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.2 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.1 µF/F 7.2 µF/F 7.8 µF/F 8.6 µF/F 7.1 µF/F 7.1 µF/F 7.2 µF/F 7.6 µF/F 8.3 µF/F 9.4 µF/F 2.0 µF/F 2.9 µF/F 1.9 µF/F 1.9 µF/F 1.9 µF/F 1.9 µF/F 1.9 µF/F 1.9 µF/F 1.9 µF/F 2.0 µF/F

HP 1638XX standard capacitor



Comments

Capacitance – Generate3 (cont)

(0.19 to 1.09) nF (1.1 to 3.29) nF (3.3 to 10.9) nF (11 to 109.9) nF (110 to 329.9) nF (0.33 to 1.09) F (1.1 to 3.29) F (3.29 to 10.9) F (11 to 32.9) F (33 to 109.9) F (110 to 329.9) F (0.33 to 1.09) mF

10 Hz to 10 kHz 10 Hz to 3 kHz 10 Hz to 1 kHz 10 Hz to 1 kHz 10 Hz to 1 kHz (10 to 600) Hz (10 to 300) Hz (10 to 150) Hz (10 to 120) Hz (10 to 80) Hz (10 to 50) Hz (10 to 20) Hz

4.4 mF/F + 0.01 nF 4.1 mF/F + 0.01 nF 2.1 mF/F + 0.01 nF 2.1 mF/F + 0.1 nF 2.1 mF/F + 0.3 nF 2.1 mF/F + 1nF 2.1 mF/F + 3 nF 2.1 mF/F + 10 nF 3.2 mF/F + 30 nF 3.7 mF/F + 100 nF 3.7 mF/F + 300 nF 3.7 mF/F + 1 µF

Fluke 5520A

Capacitance – Measure3

(10 to 100) pF 100 pF to 10 F 10 F to 10 mF

(0.1 to 100) kHz

3.4 mF/F 1.8 mF/F 2.0 mF/F

HP 4284A

Inductance – Generate3

(1 to 100) mH 1 H 10 H

(0.1 to 100) kHz

0.026 % 0.053 % 2.0 mH/H

GenRad 1482 Series

Inductance – Measure3

1 H to 1 H (1 to 10) H

(0.1 to 100) kHz

1.8 mH/H 3.8 mH/H

HP 4284A

Distortion – Measure3

20 Hz to 100 kHz

20 Hz to 20 kHz (20 to 100) kHz

1.2 dB of reading 2.3 dB of reading

HP 8903B


Parameter/Range Range CMC2 ()

Comments

Electrical Calibration of Thermocouple Indicators3 –

Type B Type C Type E Type J

Type K Type N Type R

600 C to 800 C 800 C to 1000 C 1000 C to 1550 C 1550 C to 1820 C 0 C to 150 C 150 C to 650 C 650 C to 1000 C 1000 C to 1800 C 1800 C to 2316 C -250 C to -100 C -100 C to -25 C -25 C to 350 C 350 C to 650 C 650 C to 1000 C -210 C to -100 C -100 C to -30 C -30 C to 150 C 150 C to 760 C 760 C to 1200 C -200 C to -100 C -100 C to -25 C -25 C to 120 C 120 C to 1000 C 1000 C to 1372 C -200 C to -100 C -100 C to -25 C -25 C to 120 C 120 C to 410 C 410 C to 1300 C 0 C to 250 C 250 C to 400 C 400 C to 1000 C 1000 C to 1767 C

0.34° C 0.27° C 0.24° C 0.26° C 0.24° C 0.21° C 0.25° C 0.39° C 0.65° C 0.39° C 0.13° C 0.11° C 0.13° C 0.17° C 0.25° C 0.13° C 0.12° C 0.14° C 0.18° C 0.26° C 0.14° C 0.13° C 0.20° C 0.31° C 0.31° C 0.17° C 0.15° C 0.14° C 0.21° C 0.45° C 0.66° C 0.26° C 0.32° C

Fluke 5520A


Parameter/Equipment

Range CMC2 ()

Comments

Electrical Calibration of Thermocouple Indicators3 – (cont)

Type S Type T Type U

0 C to 250 C 250 C to 1000 C 1000 C to 1400 C 1400 C to 1767 C -250 C to -150 C -150 C to 0 C 0 C to 120 C 120 C to 400 C -200 C to 0 C 0 C to 600 C

0.38° C 0.28° C 0.29° C 0.36° C 0.50° C 0.19° C 0.13° C 0.11° C 0.44° C 0.21° C

Fluke 5520A

Electrical Calibration of RTDs3 –

Pt 385, 100 Pt 3926, 100 Pt 3916, 100

-200 C to -80 C -80 C to 0 C 0 C to 100 C 100 C to 300 C 300 C to 400 C 400 C to 630 C 630 C to 800 C -200 C to -80 C -80 C to 0 C 0 C to 100 C 100 C to 300 C 300 C to 400 C 400 C to 630 C -200 C to -190 C -190 C to -80 C -80 C to 0 C 0 C to 100 C 100 C to 260 C 260 C to 300 C 300 C to 400 C 400 C to 600 C 600 C to 630 C

0.09° C 0.12° C 0.12° C 0.11° C 0.10° C 0.11° C 0.20° C 0.06° C 0.08° C 0.08° C 0.09° C 0.10° C 0.11° C 0.21° C 0.06° C 0.07° C 0.07° C 0.08° C 0.08° C 0.09° C 0.13° C 0.19° C

Fluke 5520A


Parameter/Equipment

Range CMC2 ()

Comments

Electrical Calibration of RTDs3 (cont) –

Pt 385, 200 Pt 385, 500

Pt 385, 1000 PtNi 385, 120 Cu 427, 10

-200 C to -80 C -80 C to 0 C 0 C to 100 C 100 C to 260 C 260 C to 300 C 300 C to 400 C 400 C to 600 C 600 C to 630 C -200 C to -80 C -80 C to 0 C 0 C to 100 C 100 C to 260 C 260 C to 300 C 300 C to 400 C 400 C to 600 C 600 C to 630 C -200 C to -80 C -80 C to 0 C 0 C to 100 C 100 C to 260 C 260 C to 300 C 300 C to 400 C 400 C to 600 C 600 C to 630 C -80 C to 0 C 0 C to 100 C 100 C to 260 C -100 C to 260 C

0.04° C 0.04° C 0.04° C 0.05° C 0.11° C 0.11° C 0.11° C 0.13° C 0.04° C 0.04° C 0.04° C 0.05° C 0.07° C 0.07° C 0.07° C 0.09° C 0.03° C 0.03° C 0.04° C 0.04° C 0.05° C 0.18° C 0.06° C 0.18° C 0.08° C 0.11° C 0.11° C 0.69° C

Fluke 5520A


Parameter/Equipment

Frequency CMC2, 4 ()

Comments

Phase – Measure3

-180o to +360o 0.03º

HP 53131A

Phase – Generate3, 0 to 180º

(10 to 65) Hz (65 to 500) Hz (0.5 to 1) kHz (1 to 5) kHz (5 to 10) kHz (10 to 30) kHz

0.14º 0.28º 0.52º 3.0º 5.4º 11º

Fluke 5520A

Electrical Calibration of RPM – Measure3

(0 to 100 000) RPM

0.35 RPM

HP 53131A

Oscilloscope –

Amplitude – DC3 50 Ω 1 MΩ

Amplitude – Square Wave3

50 Ω

1 MΩ

Time Marker3 Rise Time3 Bandwidth3 Bandwidth w/ Power Sensor

(-6.6 to 6.6) V (-130 to 130) V ±1 mV to ±6.6 V(p-p) 10 Hz to 10 kHz ±1 mV to ±6.6 V(p-p) 10 Hz to 1 kHz 5 s to 50 ms 20 ms to 1 ns >300 ps 50 kHz to 100 MHz (100 to 300) MHz (300 to 600) MHz (600 to 1100) MHz (1.1 to 18) GHz

1.9 mV/V + 31 µV 0.39 mV/V + 31 µV 2.0 mV/V + 31 µV 0.78 mV/V + 31 µV (19 + 39t) µs/s 2.1 µs/s 16 ps 2.8 % 3.0 % 4.1 % 4.7 % 7.5 %

Fluke 5520A/SC1100 t is time in seconds


VI. Electrical – RF/Microwave

Parameter/Equipment

Frequency

CMC2 ()

Comments

LISN –

Insertion Loss

Impedance – Magnitude

Impedance – Phase

150 kHz to 100 MHz (100 to 400) MHz 150 kHz to 100 MHz (100 to 400) MHz 150 kHz to 200 MHz (200 to 400) MHz

0.86 dB 2.2 dB 1.4 Ω 2.5 Ω 6.2 º 9.2 º

CISPR 25, C63.4-2003,CISPR 16-1-2, HP 4195A

VSWR – Measure

50 Ohms SWR < -3.5 dBm SWR > -3.5 dBm 0 < ρ ≤ 0.0476 0.0476 < ρ ≤ 0.1111 0.1111 < ρ ≤ 0.200 0.200 < ρ ≤ 0.3333 0.3333 < ρ ≤ 0.500

(0.1 to 2) GHz (0.1 to 2) GHz (0.1 to 2) GHz (0.1 to 2) GHz 50 MHz to 3 GHz (4 to 8) GHz (9 to 14) GHz (15 to 20) GHz (0.05 to 2) GHz (2 to 8) GHz (8 to 20) GHz (0.05 to 2) GHz (2 to 8) GHz (8 to 20) GHz (0.05 to 2) GHz (2 to 8) GHz (8 to 20) GHz (0.05 to 2) GHz (2 to 8) GHz (8 to 20) GHz

0.016 Γ 0.017 Γ 0.042 Γ 0.043 Γ 0.00077 ρ 0.0011 ρ 0.0022 ρ 0.0024 ρ 0.0040 ρ 0.0054 ρ 0.0078 ρ 0.0039 ρ 0.0043 ρ 0.0082 ρ 0.0086 ρ 0.0095 ρ 0.014 ρ 0.0086 ρ 0.0095 ρ 0.014 ρ

Wiltron 60A50 w/Agilent 8657A, HP8563E HP 8720C with 85052B


Parameter/Equipment

Frequency

CMC2 ()

Comments

Reflection Magnitude

(Into 50 Ohm) 0 < Γ ≤ 0.2 0.2 < Γ ≤ 0.4 0.4 < Γ ≤ 0.6 0.6 < Γ ≤ 0.8

0.8 < Γ ≤ 1.0

(0.05 to 20) GHz (0.05 to 2.0) GHz (2.0 to 20) GHz (0.05 to 2.0) GHz (2.0 to 20.) GHz (0.05 to 2.0) GHz (2.0 to 20.) GHz (0.05 to 2.0) GHz (2.0 to 20.) GHz

0.01Γ 0.01Γ 0.02Γ 0.01Γ 0.03Γ 0.02Γ 0.04Γ 0.03Γ 0.05Γ

HP 8720C

Transmission Magnitude (Into 50 Ohms)

(10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB

(10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB

50 MHz to 0.5 GHz (0.5 to 2.0) GHz

0.04 dB 0.04 dB 0.05 dB 0.07 dB 0.17 dB 0.47 dB 1.4 dB 3.5 dB 0.12 dB 0.05 dB 0.06 dB 0.06 dB 0.06 dB 0.07 dB 0.11 dB 0.25 dB

HP 8720C HP 8720C


Parameter/Equipment

Frequency CMC2 ()

Comments

Transmission Magnitude (Into 50 Ohms) (cont)

(10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB (10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB

(2.0 to 8.0) GHz (8.0 to 20) GHz

0.21 dB 0.11 dB 0.11 dB 0.11 dB 0.12 dB 0.12 dB 0.18 dB 0.32 dB 0.70 dB 0.21 dB 0.21 dB 0.21 dB 0.22 dB 0.22 dB 0.25 dB 0.37 dB

HP 8720C HP 8720C

Reflection Phase (Into 50 Ω, 0° to 360°)

0.0< Γ ≤ 0.2 0.2< Γ ≤ 0.4 0.0< Γ ≤ 0.2 0.2< Γ ≤ 0.4

(0.05 to 2.0) GHz (2.0 to 20) GHz

1.8º 1.3º 3.5º 3.0º

HP 8720C

Transmission Phase (Into 50 Ω, 0° to 360°)

(10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB (10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB

50 MHz to 0.5 GHz (0.5 to 2.0) GHz

0.31 dB 0.24 dB 0.28 dB 0.46 dB 1.1 dB 3.5 dB 11 dB 35 dB 0.59 dB 0.34 dB 0.37 dB 0.37 dB 0.37 dB 0.46 dB

HP 8720C HP 8720C


Parameter/Range

Frequency CMC2 () Comments

Transmission Phase (Into 50 Ω, 0° to 360°) (cont)

(-50 to -60) dB (-60 to -70) dB

(10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB (10 to 0) dB (0 to -10) dB (-10 to -20) dB (-20 to -30) dB (-30 to -40) dB (-40 to -50) dB (-50 to -60) dB (-60 to -70) dB

(0.5 to 2.0) GHz (2.0 to 8.0) GHz (8.0 to 20) GHz

0.72 dB 1.8 dB 1.3 dB 0.69 dB 0.69 dB 0.69 dB 0.69 dB 0.78 dB 1.0 dB 2.1 dB 5.9 dB 1.2 dB 1.3 dB 1.3 dB 1.3 dB 1.40 dB 1.8 dB 2.4 dB

HP 8720C HP 8720C

RF Power – Generate3

(+24 to -56) dBm (+13 to -127) dBm

0.01 Hz to 20 MHz (0.02 to 26.5) GHz

0.68 dB 0.19 dB

HP 3325A HP 83630B w/11792A on 8902A

RF Power – Measure3

(+30 to -20) dBm (-30 to +20) dBm

100 kHz to 2 GHz (2 to 26.5) GHz 50 MHz to 26.5 GHz

0.071 dBm 0.076 dBm 0.15 dBm

HP 8902A w/11722A HP 8902A w/ 11722A and 11792A HP 8485A w/ 438A


Parameter/Range


RF Attenuation – Tuned RF Power Measure3

(0 to -10) dB (-10 to -40) dB (-40 to -50) dB (-50 to -80) dB (-80 to -90) dB (-90 to -110) dB (-110 to -120) dB

100 kHz to 26.5 GHz

0.026 dB 0.064 dB 0.16 dB 0.20 dB 0.32 dB 0.36 dB 0.54 dB

HP 8902A HP 11722A HP 11792A HP 11793A

Phase Modulation – Measure3

Rate: 200 Hz to 10 kHz Rate: 200 Hz to 20 kHz

Rate: 200 Hz to 20 kHz

150 kHz to 10 MHz 10 MHz to 1.3 GHz (1.3 to 26.5) GHz

5.1 % 4.3 % 4.3 %

HP 8902A w/11722A HP 8902A w/ 11793A

Amplitude Modulation – Measure3

Rate: 50 Hz to 10 kHz Depths: 5 % to 99 % Rate: 20 Hz to 10 kHz Depths: to 99 % Rate: 50 Hz to 50 kHz Depths: 5 % to 99 % Rate: 20 Hz to 100 kHz Depths: to 99 % Rate: 20 Hz to 100 kHz Depths: to 99 % Rate: 20 Hz to 100 kHz Depths: to 99 %

150 kHz to 10 MHz 150 kHz to 10 MHz 10 MHz to 1.3 GHz 10 MHz to 1.3 GHz (1.3 to 26.5) GHz (1.3 to 26.5) GHz

2.5 % 3.8 % 1.3 % 3.8 % 1.3 % 3.4 %

HP 8902A w/11722A

w/ 11793A


Parameter/Range


Frequency Modulation – Measure3

Rate: 20 Hz to 10 kHz Dev.: ≤ 40 kHz peak Rate: 50 Hz to 100 kHz Dev.: ≤ 400 kHz peak Rate: 20 Hz to 200 kHz Dev.: ≤ 400 kHz peak

Rate: 50 Hz to 100 kHz Dev.: ≤ 400 kHz peak Rate: 20 Hz to 200 kHz Dev.: ≤ 400 kHz peak

250 kHz to 10 MHz 10 MHz to 1.3 GHz 10 MHz to 1.3 GHz (1.3 to 26.5) GHz (1.3 to 26.5) GHz

2.5 % 1.3 % 6.2 % 1.3 % 6.2 %

HP 8902A w/11722A

w/ 11793A

V. Mechanical

Parameter/Equipment

Range CMC2 ()

Comments

Mass

(0 to 100) g 100 g to 3 kg (3 to 4.8) kg (4.8 to 24) kg

0.22 mg 20 mg 90 mg 0.58 g

Mettler AE100 w/ Class S weights Mettler PJ3000 w/ Class 1 weights Mettler SB24001 w/ Class 1 and Class F weights

Scales & Balances3

(1 to 5) mg (5 to 10) mg (10 to 20) mg (20 to 50) mg (50 to 100) mg (100 to 200) mg (200 to 500) mg 500 mg to 1 g (1 to 2) g (2 to 5) g (5 to 10) g (10 to 20) g (20 to 50) g

6.4 µg 6.4 µg 6.4 µg 6.4 µg 6.4 µg 6.4 µg 6.4 µg 22 µg 20 µg 40 µg 0.018 mg 0.048 mg 0.048 mg

Class S1 weights


Parameter/Equipment

Range CMC2 ()

Comments

Scales & Balances3

(cont)

(50 to 100) g (100 to 200) g (200 to 500) g (500 to 1000) g (1 to 2) kg (2 to 5) kg (5 to 10) kg (10 to 20) kg (0.5 to 10) lb (10 to 25) lb (25 to 50) lb (50 to 100) lb (100 to 500) lb

0.090 mg 0.20 mg 0.21 mg 0.18 mg 1 mg 5.0 mg 7.7 mg 72 mg 0.0013 lb 0.0029 lb 0.058 lb 0.058 lb 0.061 lb

Class S1 weights Class F weights

Durometer Calibration3 – A, B, C, and D

Indentor extension and shape- Diameter Radius Angle Extension Indentor Display Spring Calibration- Force

0 to 100 duro 0.77 duro

Rex RDC-1 Durocalibrator Optical inspection

Torque – Measuring Equipment

100 in·ozf to 100 in·lbf100 in·lbf to 250 ft·lbf

0.00059 in·lbf/in·lbf 0.00030 ft·lbf/ft·lbf

CDI 2000-151-0 CDI 2000-152-0

Torque – Measure

(20 to 200) in·ozf 200 in·ozf to 250 ft·lbf (250 to 2000) ft·lbf

0.0081 in·ozf/in·ozf 0.0031 ft·lbf/ft·lbf 0.0013 ft·lbf/ft·lbf

CDI 2001 0-TTP w/ 950DT CDI TTPM-41 w/ 950DT AKO, Inc. TSD 2050 torque system

Pressure3

(-14.5 to 0) psig (0 to 100) psig (100 to 200) psig (200 to 500) psig (501 to 10 000) psig

0.012 psi 0.061 psi 0.068 psi 0.14 psi 2.1 psi

DPI 620 calibrator w/GE pressure sensor Pressurements DPT W2200/3


Parameter/Equipment

Range CMC2, 5 ()

Comments

Pressure3 (cont)

(0 to 0.25) inH2O (0.25 to 2) inH2O (2 to 10) inH2O

0.0017 inH2O 0.0029 inH2O 0.014 inH2O

Heisse PTE-1 w/ HQS-1

Force3 – Tension and Compression3 Load Cells, Force Gages, Dynamometers

(0 to 500) lbf (501 to 5000) lbf (5001 to 50 000) lbf (50 001 to 100 000) lbf (100 001 to 200 000) lbf (0.125 to 1) lbf (1 to 10) lbf (10 to 50) lbf (50 to 100) lbf (100 to 500) lbf

0.039 % 0.063 % 0.056 % 0.068 % 0.074 % 0.019 % 0.014 % 0.013 % 0.018 % 0.0050 %

Interface 1600 Gold Series Class F Weights

Speed3

Up to 50 in/min 0.081 in/min

Stopwatch/ Red Lion Controls PAXI

Vibration

0.5 ≤ f < 1 1 ≤ f < 2 2 ≤ f < 5 5 ≤ f < 10 10 Hz to 99 Hz 100 Hz 100 Hz to 920 Hz 921 Hz to 5000 Hz 5001 Hz to 10 000 Hz 10 001 Hz to 15 000 Hz 15 001 Hz to 20 000 Hz

4.0 % 1.5 % 1.0 % 1.0 % 1.7 % 1.3 % 1.4 % 1.7 % 2.2 % 3.7 % 4.8 %

Modal Shop 9155

Impact Hammer

0 to 5000 lbs 2.8 % Model 9155C Hammer

Calibration System


Parameter/Equipment

Range CMC2, 5 ()

Comments

Shock

Up to 10 000 g 2.0 % Model 9525 Pneumatic

Shock Exciter

VI. Thermodynamics

Parameter/Equipment

Range CMC2 () Comments

Temperature – Measure3

-40 C to 400 C 400 C to 500 C

0.077 ºC 0.22 ºC

Hart 5618B PRT w/ 1502

IR Temperature – Measuring Equipment3

50C to 100 C 100 C to 200 C 200 C to 300 C 300 C to 400 C 400 C to 500 C

0.60 C 0.61 C 0.77 C 0.79 C 0.99 C

Hart 9132

Relative Humidity – Measure3

5 % RH to 95 % RH

1.3 % RH

Vaisala HM70 w/probe HMP46

VII. Time& Frequency

Parameter/Equipment

Range CMC2 () Comments

Frequency – Measuring Equipment3

DC to 20 MHz 10 MHz to 26.5 GHz 10 MHz

0.00058 parts in 106 0.29 parts in 106 5.1 parts in 1012

HP 3325B HP 83630B GPS

Frequency – Measure3

DC to 3 GHz 10 Hz to 26.5 GHz

0.00026 parts in 106 0.22 parts in 106

HP 53131A HP 5351B

Time Interval3

1 s to 3 hr 0.59 s

53131A w/GPS NIST SP960-12

____________________________________________


1 This laboratory offers commercial and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement

that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMC’s represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer’s device and to influences from the circumstances of the specific calibration.

3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 – General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer’s site being larger than the CMC.

4 The stated measured values are determined using the indicated instrument (see Comments). This

capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMC’s are expressed as either a specific value that covers the full range or as a percent or fraction of the reading plus a fixed floor specification.

5 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches.

In the statement of CMC, the value is defined as the percentage of reading, unless otherwise noted.

For the calibrations to which this accreditation applies, please refer to the laboratory’s Calibration Scope of Accreditation.

Accredited Laboratory

A2LA has accredited

TEKTRONIX, INC Novi, MI

for technical competence in the field of

Calibration

This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of

ANSI/NCSLI Z540-1-1994 and any additional program requirements in the field of calibration. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-

IAF Communiqué dated 8 January 2009).

Presented this 20th day of January 2016. _______________________ Senior Director, Quality and Communications For the Accreditation Council Certificate Number 2357.15 Valid to December 31, 2017

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 CALIBRATION · (A2LA Cert. No. 2357.15) Revised...

Documents

Transcript of SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 CALIBRATION · (A2LA Cert. No. 2357.15) Revised...