Schneider Training Center€ €€€Course catalogue...

Schneider Training Center

Course catalogue 8/27/2020

Index TRNOSEDETUB1E (On-site) - Micrologic® Basic Trip Unit 4 TRNOSEDETUA1E (On-site) - Micrologic® Trip Unit, A-Series 5 TRNOSEDETUP1E (On-site) - Micrologic® Trip Unit, P-Series 6 TRNOSEDETUH1E (On-site) - Micrologic® Trip Unit, H-Series 7 TRNOSEDETVS1E (On-site) - Surgelogic® TVSS 8 TRNOSEDETSY1E (On-site) - TeSys T Controller Operation 9 TRNOSEDEION1E (On-site) - ION Meter Series 7000 10 TRNOSEDEMCL4E (On-Site) - Masterclad® Switchgear Maintenance 11 TRNOSEDEMCL1E (On-Site) - Masterclad® Switchgear Operator 12 TRNOSEDEVRB4E (On-Site) - VR Vacuum Circuit Breaker Maintenance 13 TRNOSEDEVRB1E (On-Site) - VR Vacuum Circuit Breaker Operator 14 TRNOSEDEHVL4E (On-Site) - HVL™ and HVL/cc™ Load Interrupter Switch Maintenance 15 TRNOSEDEHVL1E (On-Site) - HVL™ and HVL/cc™ Load Interrupter Switch Operator 16 TRNOSEDEMMC4E (On-Site) - Motorpact™ Medium-voltage Motor Control Center (MVMCC) with Vacuum Contactors

Maintenance 17

TRNOSEDEMMC1E (On-Site) - Motorpact™ Medium-voltage Motor Control Center (MVMCC) with Vacuum Contactors Operator 18 TRNOSEDERLY2E (On-Site) - Medium-Voltage Relay – Operator: SEPAM, Multilin, Schweitzer, or Basler Type Relay 19 TRNOSEDELFP4E (On-Site) - Liquid-Filled Padmount Transformer (Class 7230) Maintenance 20 TRNOSEDELFP1E (On-Site) - Liquid-Filled Padmount Transformer (Class 7230) Operator 21 TRNOSEDELFS4E (On-Site) - Liquid-Filled Unit Substation Transformer (Class 7240) Maintenance 22 TRNOSEDELFS1E (On-Site) - Liquid-Filled Unit Substation Transformer (Class 7240) Operator 23 TRNOSEDEPC24E (On-Site) - Power-Cast II™ Cast Coil Transformer (Class 7300) Maintenance 24 TRNOSEDEPC21E (On-Site) - Power-Cast II™ Cast Coil Transformer (Class 7300) Operator 25 TRNOSEDEPD24E (On-Site) - Power-Dry II™ Dry-Type Transformer (Class 7400) Maintenance 26 TRNOSEDEPD21E (On-Site) - Power-Dry II™ Dry-Type Transformer (Class 7400) Operator 27 TRNOSEDEPZ44E (On-Site) - Power-Zone® IV (PZ4) Switchgear Maintenance 28 TRNSCEDEPZ41E (On-Site) - Power-Zone® IV (PZ4) Switchgear Operator 29 TRNOSEDEQD24E (On-Site) - POWER-STYLE® QED2 Switchboard Maintenance 30 TRNOSEDEQD21E (On-Site) - POWER-STYLE™ QED2 Switchboard Operator 31 TRNOSEDEQD64E (On-Site) - POWER-STYLE™ QED6 Switchboard Maintenance 32 TRNOSEDEQD61E (On-Site) - POWER-STYLE™ QED6 Switchboard Operator 33 TRNOSEDELMC4E (On-Site) - Model 6 Low-voltage Motor Control Center Maintenance 34 TRNOSEDELMC1E (On-Site) - Model 6 Low-voltage Motor Control Center Operator 35 TRNOSEDEMCC4E (On-Site) - Model 6 Low-voltage Intelligent Motor Control Center (iMCC) Course 36 TRNOSEDEATV611E (On-Site) - Altivar® 61/71 Drive Operation 37 TRNOSEDENWB4E (On-Site) - Masterpact® NW Circuit Breaker Maintenance 38 TRNOSEDENWB1E (On-Site) - Masterpact® NW Circuit Breaker Operator 39

TRNOSEDETUB1E (On-site) - Micrologic® Basic Trip Unit

Course Code: TRNOSEDETUB1E

Duration: 1 Hour

Time: TBD

Type: Instructor Led

Language: English

Cost: Request a Quote

DescriptionThis course will provide participants with classroom and hands-on exposure to the Micrologic Basic Trip Unit used on Masterpact and PowerPact Circuit Breakers, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.

Target Audience● Maintenance and Operations personnel

ObjectivesAfter completing this course, participants will be able to:● State the purpose of a Micrologic Basic Trip Unit● Identify the components of a Micrologic Basic Trip Unit and state their functions● Demonstrate the ability to perform initial set up on a Micrologic Basic Trip unit● State the differences between the Basic Trip Unit and other trip units in the Micrologic Trip Unit series● Demonstrate the ability to navigate the available menus of a Micrologic Basic trip unit using the front face buttons● Demonstrate the ability to replace a Micrologic Basic Trip Unit and all of its field replaceable components

Prerequisites● Requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams● Use and functions of the Micrologic Full Function Test Set

Course occasions / Notification

Course occation will be arranged when min. 5 participants have registered for Interest.

TRNOSEDETUA1E (On-site) - Micrologic® Trip Unit, A-Series

Course Code: TRNOSEDETUA1E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Micrologic A-Series Trip Unit used on Masterpact and PowerPact Circuit Breakers, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


ObjectivesAfter completing this course, participants will be able to:● State the purpose of a Micrologic A-Series Trip Unit. ● Identify the components of a Micrologic A-Series Trip Unit and state their functions

● Demonstrate the ability to perform initial set up on a Micrologic A-Series Trip Unit ● State the differences between the A-Series Trip Unit and other trip units in the Micrologic Trip Unit series● Demonstrate the ability to navigate the available menus of a Micrologic A-Series Trip Unit using the front face buttons● Demonstrate the ability to replace a Micrologic A-Series Trip Unit and all of its field replaceable components

Prerequisites● Requirements of the NFPA 70E ● Lockout/tagout procedures● One line and three line diagrams● Use and functions of the Micrologic Full● Function Test Set



TRNOSEDETUP1E (On-site) - Micrologic® Trip Unit, P-Series

Course Code: TRNOSEDETUP1E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Micrologic P-Series Trip Unit used on Masterpact and PowerPact Circuit Breakers, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


ObjectivesAfter completing this course, participants will be able to:● State the purpose of a Micrologic P-Series Trip Unit● Identify the components of a Micrologic P-Series Trip Unit and state their functions

● Demonstrate the ability to perform initial set up on a Micrologic P-Series Trip Unit ● State the differences between the P-Series Trip Unit and other trip units in the Micrologic Trip Unit series● Demonstrate the ability to navigate the available menus of a Micrologic P-Series trip unit using the front face buttons● Demonstrate the ability to replace a Micrologic P-Series Trip Unit and all of its field replaceable components

Prerequisites● Requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams● Use and functions of the Micrologic Full Function Test Set



TRNOSEDETUH1E (On-site) - Micrologic® Trip Unit, H-Series

Course Code: TRNOSEDETUH1E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Micrologic H-Series Trip Unit used on Masterpact and PowerPact Circuit Breakers, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


ObjectivesAfter completing this course, participants will be able to:● State the purpose of a Micrologic H-Series Trip Unit● Identify the components of a Micrologic H-Series Trip Unit and state their functions● Demonstrate the ability to perform initial set up on a Micrologic H-Series Trip Unit ● State the differences between the H-Series Trip Unit and other trip units in the Micrologic Trip Unit series● Demonstrate the ability to navigate the available menus of a Micrologic H-Series trip unit using the front face buttons● Demonstrate the ability to replace a Micrologic H-Series Trip Unit and all of its field replaceable components

Prerequisites● Requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams● The use and functions of the Micrologic Full Function Test Set



TRNOSEDETVS1E (On-site) - Surgelogic® TVSS

Course Code: TRNOSEDETVS1E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Surgelogic TVSS, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.

Target Audience● Operations and Maintenance personnel

ObjectivesAfter completing this course, participants will be able to:● State the purpose of the Surgelogic TVSS● Identify the components of the Surgelogic TVSS● Demonstrate the ability to:● Read information on the front face of a TVSS● Safely perform the manufacturer start up procedures● Safely replace a TVSS and all its field replaceable components

Prerequisites● Requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams



TRNOSEDETSY1E (On-site) - TeSys T Controller Operation

Course Code: TRNOSEDETSY1E

Duration: 4 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to TeSys T Motor Controllers. Students will learn basic operations and configuration of the controllers.

Target Audience● Operations personnel

Objectives● Identify the hardware components of the TeSys T Motor Management System● Understand the acronyms and designations used in TeSys T schematics● Navigate the menus on the interface.● Configure the system parameters of the TeSys T Motor Management System● Verify the configuration of the TeSys T Motor Management System● Modify the parameters of the TeSys T Motor Management System● Interpret diagnostic fault messages of the TeSys T Motor Management System● Troubleshoot the TeSys T Motor Management System

Prerequisites● Safety regulations including the NFPA 70E● Basic electrical knowledge● Reading one-line diagrams

● Basic motor control theory



TRNOSEDEION1E (On-site) - ION Meter Series 7000

Course Code: TRNOSEDEION1E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the ION Meter Series 7000, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.

Target Audience● Operations and Maintenance personnel

ObjectivesAfter completing this course, participants will be able to:● State the purpose of the ION Meter Series 7000● Identify the components of the ION Meter Series 7000Demonstrate the ability to:● State the purpose of the ION Meter Series 7000● Identify the basic components of a ION Meter Series 7000● List the methods of connecting a ION Meter Series 7000 to a communications network● Demonstrate the ability to navigate the available menus of a ION Meter Series 7000 series meter

Prerequisites● Requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams



TRNOSEDEMCL4E (On-Site) - Masterclad® Switchgear Maintenance

Course Code: TRNOSEDEMCL4E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Masterclad Switchgear, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.

Target AudienceMaintenance Personnel

ObjectivesAfter completing this course, participants will be able to:● Identify the components of Masterclad Switchgear● List the different types of bus configuration● Demonstrate the ability to properly operate Masterclad Switchgear● Demonstrate the ability to safely energize and de-energize Masterclad Switchgear● Demonstrate the ability to perform the manufacturer’s recommended maintenance procedures

PrerequisitesThe participants should be familiar with:● The requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams● Test equipment such as High Potential (HiPot), Insulation Test Set, Multimeter



TRNOSEDEMCL1E (On-Site) - Masterclad® Switchgear Operator

Course Code: TRNOSEDEMCL1E

Duration: 2 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Masterclad Switchgear, and will provide the students with the opportunity to safely operate the installed equipment at their locations.

Target AudienceOperator Personnel

Objectives● Identify the components of Masterclad Switchgear ● List the different types of bus configuration

● Demonstrate the ability to properly operate Masterclad Switchgear ● Demonstrate the ability to safely energize and de-energize Masterclad Switchgear

PrerequisitesThe participants should be familiar with:● The requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams



TRNOSEDEVRB4E (On-Site) - VR Vacuum Circuit Breaker Maintenance

Course Code: TRNOSEDEVRB4E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the VR circuit breaker, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Equipment● High Potential (HiPot) test set ● Insulation resistance test set ● Contact resistance test set ● Multimeter ● Feeler gauges

Objectives● Identify the components of a VR circuit breaker and list their functions

● List the three positions of a VR vacuum circuit breaker in Masterclad Switchgear and identify the position indications associated with each

● Demonstrate the ability to safely insert and remove a VR vacuum breaker from a Masterclad Switchgear cell ● Demonstrate the ability to safely rack in and rack out a VR vacuum circuit breaker ● Demonstrate the ability to safely open and close a VR vacuum circuit breaker ● Demonstrate the ability to safely start-up and perform manufacturer’s recommended maintenance on a VR vacuum circuit breaker




TRNOSEDEVRB1E (On-Site) - VR Vacuum Circuit Breaker Operator

Course Code: TRNOSEDEVRB1E

Duration: 2 hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the VR circuit breaker, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.

Target AudienceOperations Personnel

Objectives● Identify the components of a VR circuit breaker and list their functions ● List the three positions of a VR vacuum circuit breaker in Masterclad Switchgear and identify the position indications associated with each

● Demonstrate the ability to safely insert and remove a VR vacuum breaker from a Masterclad Switchgear cell ● Demonstrate the ability to safely rack in and rack out a VR vacuum circuit breaker ● Demonstrate the ability to safely open and close a VR vacuum circuit breaker




TRNOSEDEHVL4E (On-Site) - HVL™ and HVL/cc™ Load Interrupter Switch Maintenance

Course Code: TRNOSEDEHVL4E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the HVL and HVL/cc Load Interrupter Switch, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components of HVL and HVL/cc Load Interrupter Switch

● Identify the position indications associated with each HVL load interrupter switch position

● Demonstrate the ability to properly operate HVL and HVL/cc Load Interrupter Switch Switchgear ● Demonstrate the ability to safely open and close an HVL and HVL/cc Load Interrupter Switch

● Demonstrate the ability to perform the manufacturer’s recommended maintenance procedures




TRNOSEDEHVL1E (On-Site) - HVL™ and HVL/cc™ Load Interrupter Switch Operator

Course Code: TRNOSEDEHVL1E

Duration: 2 Hours

Time: TBD


Language: English




Objectives● Identify the components of HVL and HVL/cc Load Interrupter Switch Switchgear ● Identify the position indications associated with each HVL load interrupter switch position

● Demonstrate the ability to properly operate HVL and HVL/cc Load Interrupter Switch Switchgear ● Demonstrate the ability to safely energize and de-energize HVL and HVL/cc Load Interrupter Switch Switchgear




TRNOSEDEMMC4E (On-Site) - Motorpact™ Medium-voltage Motor Control Center (MVMCC) with Vacuum Contactors Maintenance

Course Code: TRNOSEDEMMC4E

Duration: 4 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Motorpact Medium-voltage Motor Control Center with Vacuum Contactors, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Equipment§ ... §

Objectives● Identify the components and list the functions of Motorpact Medium-voltage Motor Control Center with Vacuum Contactors

● Identify the positions available with a MVMCC contactor disconnect switch

● Demonstrate the ability to properly operate Motorpact MVMCC key interlock system

● Demonstrate the ability to safely open and close a Motorpact MVMCC disconnect ● Demonstrate the ability to safely rack in and rack out the MVMCC contactor ● Demonstrate the ability to safely insert and remove the MVMCC contactor from the MVMCC cell ● Demonstrate the ability to safely perform the manufacturer recommended maintenance procedures for a MVMCC and vacuum contactor




TRNOSEDEMMC1E (On-Site) - Motorpact™ Medium-voltage Motor Control Center (MVMCC) with Vacuum Contactors Operator

Course Code: TRNOSEDEMMC1E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Motorpact Medium-voltage Motor Control Center with Vacuum Contactors, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components and list the functions of Motorpact Medium-voltage Motor Control Center with Vacuum Contactors

● Identify the positions available with a MVMCC contactor disconnect switch

● Demonstrate the ability to properly operate Motorpact MVMCC key interlock system

● Demonstrate the ability to safely open and close a Motorpact MVMCC disconnect ● Demonstrate the ability to safely rack in and rack out the MVMCC contactor ● Demonstrate the ability to safely insert and remove the MVMCC contactor from the MVMCC cell




TRNOSEDERLY2E (On-Site) - Medium-Voltage Relay – Operator: SEPAM, Multilin, Schweitzer, or Basler Type Relay

Course Code: TRNOSEDERLY2E

Duration: 2 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to MV relays, and will provide the students with the opportunity to safely operate and configure the installed equipment at its location.

Target AudienceOperations and Maintenance Personnel

ObjectivesDemonstrate the ability to:

• State the purpose of the MV Relay

• Identify the basic components of a MV Relay

• Navigate the available menus of a MV Relay

• Setup and configure the relay to desired settings

• Navigate the troubleshooting menu

PrerequisitesThe participants should be familiar with:● The requirements of the NFPA 70E● Lockout/tagout procedures● Ability to read one-line and three-line diagrams and electrical schematics



TRNOSEDELFP4E (On-Site) - Liquid-Filled Padmount Transformer (Class 7230) Maintenance

Course Code: TRNOSEDELFP4E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Liquid Filled Unit Substation Transformer, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components of Liquid Filled Unit Substation Transformer and list their functions

● Demonstrate their ability to change the tap settings on a substation transformer ● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a substation transformer ● Demonstrate their ability to perform the manufacturer’s recommended maintenance on a substation transformer




TRNOSEDELFP1E (On-Site) - Liquid-Filled Padmount Transformer (Class 7230) Operator

Course Code: TRNOSEDELFP1E

Duration: 1 Hour

Time: TBD


Language: English




Objectives● Identify the components of Liquid Filled Padmount Transformer ● Identify the components of a padmount transformer and list their functions

● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a padmount transformer




TRNOSEDELFS4E (On-Site) - Liquid-Filled Unit Substation Transformer (Class 7240) Maintenance

Course Code: TRNOSEDE-LFS-4E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Liquid Filled Unit Substation Transformer, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations


Objectives● Identify the components of Liquid Filled Unit Substation Transformer ● Identify the components of a substation transformer and list their functions

● Demonstrate their ability to change tap settings on a substation transformer ● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a substation transformer ● Demonstrate their ability to safely perform start-up and maintenance procedures on a substation transformer

PrerequisitesThe participants should be familiar with: ● The requirements of the NFPA 70E

● Lockout/tagout procedures● One line and three line diagrams● Familiarity with the following test equipment: - Insulation test set, Transformer turns ratio test set, Multimeter



TRNOSEDELFS1E (On-Site) - Liquid-Filled Unit Substation Transformer (Class 7240) Operator

Course Code: TRNOSEDELFS1E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Liquid Filled Unit Substation Transformer, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.



● Demonstrate their ability to change tap settings on a substation transformer ● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a substation transformer

PrerequisitesThe participants should be familiar with:● The requirements of the NFPA 70E● Lockout/tagout procedures● One line and three line diagrams● Familiarity with the following test equipment: Insulation test set, Transformer turns ratio test set, & Multimeter



TRNOSEDEPC24E (On-Site) - Power-Cast II™ Cast Coil Transformer (Class 7300) Maintenance

Course Code: trnosEDEPC24E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Power-Cast II Cast Coil Transformer and Model 98 Digital Temperature Controller, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


EquipmentFamiliarity with the following test equipment:● Insulation test set● Transformer turns ratio test set● Multimeter

Objectives● Identify the components of Power-Cast II Cast Coil Transformer ● Identify the components of a Power-Cast II Cast Coil Transformer and list their functions

● Demonstrate their ability to change tap settings on a substation transformer ● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a Power-Cast II Cast Coil Transformer ● Demonstrate their ability to safely perform start-up and maintenance procedures on a Power-Cast II Cast Coil Transformer ● State the purpose of the Model 98 Digital Temperature Controller ● Identify the components of the Model 98 Digital Temperature Controller ● Demonstrate the ability to:- manually operate the fans via the key pad

- set up controller communications

- navigate through the controller key pad displays




TRNOSEDEPC21E (On-Site) - Power-Cast II™ Cast Coil Transformer (Class 7300) Operator

Course Code: TRNOSEDEPC21E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Power-Cast II Cast Coil Transformer, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.



Objectives● Identify the components of Power-Dry II Dry-Type Transformer ● Identify the components of a Power-Dry II Transformer and list their functions

● Demonstrate their ability to change tap settings on a Power-Dry II Transformer ● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a Power-Dry II Transformer

Prerequisites● The requirements of the NFPA 70E

● Lockout/tagout procedures

● One line and three line diagrams



TRNOSEDEPD24E (On-Site) - Power-Dry II™ Dry-Type Transformer (Class 7400) Maintenance

Course Code: TRNOSEDEPD24E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Power-Cast II Cast Coil Transformer and Model 98 Digital Temperature Controller, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.




● Demonstrate their ability to change tap settings on a substation transformer ● Demonstrate their ability to read and interpret the indicators commonly mounted on the transformer ● Demonstrate the ability to safely energize and de-energize a substation transformer ● Demonstrate their ability to safely perform start-up and maintenance procedures on a substation transformer ● State the purpose of the Model 98 Digital Temperature Controller ● Identify the components of the Model 98 Digital Temperature Controller ● Demonstrate the ability to:- manually operate the fans via the key pad

- set up controller communications

- navigate through the controller key pad displays






TRNOSEDEPD21E (On-Site) - Power-Dry II™ Dry-Type Transformer (Class 7400) Operator

Course Code: TRNOSEDEPD21E

Duration: 1 Hour

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Power-Cast II Cast Coil Transformer, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components of Power-Dry II Dry-Type Transformer ● Identify the components of a Power-Dry II Transformer and list their functions

● Demonstrate the ability to safely energize and de-energize a Power-Dry II Transformer






TRNOSEDEPZ44E (On-Site) - Power-Zone® IV (PZ4) Switchgear Maintenance

Course Code: TRNSCEDEPZ44E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Power-Zone IV (PZ4) Switchgear, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components of Power-Zone IV (PZ4) Switchgear ● List the different types of bus configuration available in Power-Zone IV (PZ4) Switchgear ● Demonstrate the ability to safely energize and de-energize the PZ4 Switchgear ● Demonstrate the ability to properly operate PZ4 Switchgear key interlock systems

● Demonstrate the ability to safely start-up and perform the manufacturer’s recommended maintenance procedures for QED2 Switchboard






TRNSCEDEPZ41E (On-Site) - Power-Zone® IV (PZ4) Switchgear Operator

Course Code: TRNOSEDEPZ41E

Duration: 2 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Power-Zone IV (PZ4) Switchgear, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components of Power-Zone IV (PZ4) Switchgear ● List the different types of bus configuration available in Power-Zone IV (PZ4) Switchgear ● Demonstrate the ability to safely energize and de-energize the PZ4 Switchgear ● Demonstrate the ability to properly operate PZ4 Switchgear key interlock systems






TRNOSEDEQD24E (On-Site) - POWER-STYLE® QED2 Switchboard Maintenance

Course Code: TRNOSEDEQD24E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the POWER-STYLE QED2 Switchboard, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Equipment● Insulation resistance test set ● Multimeter

Objectives● Identify the components of POWER-STYLE QED2 Switchboard

● List the different types of bus configuration available in POWER-STYLE QED2 Switchboard

● Demonstrate the ability to safely energize and de-energize the QED2 Switchboard

● Demonstrate the ability to properly operate QED2 Switchboard key interlock systems







TRNOSEDEQD21E (On-Site) - POWER-STYLE™ QED2 Switchboard Operator


Duration: 2 Hours

Time: TBD


Language: English













TRNOSEDEQD64E (On-Site) - POWER-STYLE™ QED6 Switchboard Maintenance


Duration: 2 Hours

Time: TBD


Language: English















TRNOSEDEQD61E (On-Site) - POWER-STYLE™ QED6 Switchboard Operator


Duration: 1 Hour

Time: TBD


Language: English













TRNOSEDELMC4E (On-Site) - Model 6 Low-voltage Motor Control Center Maintenance

Course Code: TRNOSEDELMC4E

Duration: 2 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Model 6 Low-voltage Motor Control Center, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.



Objectives● Identify the components of the Model 6 Low-voltage Motor Control Center ● List the available positions of a Model 6 LVMCC motor contactor disconnect switch

● Demonstrate the ability to safely energize and de-energize a Model 6 LVMCC

● Demonstrate the ability to safely operate a model 6 LVMCC motor contactor disconnect switch

● Demonstrate the ability to perform start-up and manufacturer’s recommended maintenance procedures for a Model 6 Motor Control Center






TRNOSEDELMC1E (On-Site) - Model 6 Low-voltage Motor Control Center Operator

Course Code: TRNOSEDELMC1E

Duration: 1 Hour

Time: TBD

Type: Instrucor Led

Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Model 6 Low-voltage Motor Control Center, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Objectives● Identify the components of the Model 6 Low-voltage Motor Control Center ● List the available positions of a Model 6 LVMCC motor contactor disconnect switch

● Demonstrate the ability to safely energize and de-energize a Model 6 LVMCC

● Demonstrate the ability to safely operate a model 6 LVMCC motor contactor disconnect switch






TRNOSEDEMCC4E (On-Site) - Model 6 Low-voltage Intelligent Motor Control Center (iMCC) Course

Course Code: TRNOSEDEMCC4E

Duration: 1 Day

Time: TBD


Language: English


DescriptionThis course will provide the participants the knowledge and hands on experience to commission and maintain the intelligent devices and network communications within their Model 6 Intelligent Motor Control Center (iMCC) at their facility.

Target AudienceOperations and Maintenance Personnel who have completed all prerequisites

Equipment● Laptop Computer ● Windows Programs

Objectives● Identify the various components that can be installed in an Intelligent Motor Control Center ● Be able to perform commissioning and maintenance of installed components ● Be able to establish and troubleshoot a variety of an Intelligent Motor Control Center communications networks

Prerequisites● Model 6 Low-voltage Motor Control Center Operations (EDE-LMC-1E) or Maintenance (EDE-LMC-4E) Course

● Introduction to Variable Frequency Drives (VFDBAS01) Course

● Altivar 61/71 Drive Maintenance and Troubleshooting (VFDA7142) Course

● PowerLogic System installation and Troubleshooting (3000PLUC100) Course

● Tesys T Motor Management System (CTLW183) Course

● Must have basic PLC communication knowledge



TRNOSEDEATV611E (On-Site) - Altivar® 61/71 Drive Operation

Course Code: TRNOSEDEATV611E

Duration: 1 Day

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to Altivar 61/71 drives. Students will learn basic operations and configuration of the drives.


Objectives● Identify the hardware components of the Altivar 61/71 AC Drive. ● Configure the system parameters of the Altivar 61/71 AC Drive for the material handling, general use, and HVAC. ● Verify the configuration of the Altivar 61/71 AC Drive. ● Modify the parameters of the Altivar 61/71 AC Drive. ● Interrupt diagnostic fault messages of the Altivar 61/71 AC Drive. ● Troubleshoot the Altivar 61/71 AC Drive. ●

●

Prerequisites❍ Safety regulations including the NFPA 70E

❍ Basic electrical knowledge, including reading one-line diagrams

❍ Basic motor control theory ●

●

●

●



TRNOSEDENWB4E (On-Site) - Masterpact® NW Circuit Breaker Maintenance

Course Code: TRNOSEDENWB4E

Duration: 3 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Masterpact NW Circuit Breaker, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.


Equipment● High Current test set for Primary Injection testing

● Insulation resistance test set ● Contact resistance test set ● Multimeter


● List the three positions of a NW circuit breaker in PZ4 Switchgear and identify the position indications associated with each

● Demonstrate the ability to safely insert and remove a NW breaker from a PZ4 Switchgear cell ● Demonstrate the ability to safely rack in and rack out a NW circuit breaker ● Demonstrate the ability to safely open and close a NW circuit breaker ● Demonstrate the ability to safely start-up and perform manufacturer’s recommended maintenance on a NW circuit breaker






TRNOSEDENWB1E (On-Site) - Masterpact® NW Circuit Breaker Operator

Course Code: TRNOSEDENWB1E

Duration: 2 Hours

Time: TBD


Language: English


DescriptionThis course will provide participants with classroom and hands-on exposure to the Masterpact NW Circuit Breaker, and will provide the students with the opportunity to safely operate and maintain the installed equipment at their locations.



● List the three positions of a NW circuit breaker in PZ4 Switchgear and identify the position indications associated with each ● Demonstrate the ability to safely insert and remove a NW breaker from a PZ4 Switchgear cell ● Demonstrate the ability to safely rack in and rack out a NW circuit breaker ● Demonstrate the ability to safely open and close a NW circuit breaker






Schneider Training Center€ €€€Course catalogue...

Documents

Transcript of Schneider Training Center€ €€€Course catalogue...