Samsung ps43d450a2wxzg chassis_f82a_sm

Plasma TVChassis F82A

Model Code PS43D450A2WXZG

SERVICE MANUAL

Plasma TV

PS43D450A2W

Refer to the service manual in the GSPN (see the rear cover) for more information.

1. Precaution

1. PrecautionTo avoid possible damage, electric shocks or exposure to radiation, follow the instructions below with regard to safety,installation, service and ESD.

1.1. Safety Precautions

1) Make sure all protective devices are properly installed including non-metallic handles and compartment covers wheninstalling or re-installing the chassis or chassis assemblies.

2) Make sure that no gaps exist between the cabinets for children to insert their fingers in to prevent children fromreceiving electric shocks. Gaps mentioned above include ventilation holes of a too great magnitude between the PDPmodule and the cabinet mask, and the improper installation of the rear cabinet.Errors may occur when the resistance is below 1.0MΩ or over 5.2MΩ. In these cases, make sure that the device isrepaired before sending it back to the customer.

3) Check for Electricity Leakage (AC Leakage Test)

WARNING

Do not use an insulated transformer for checking the leakage. Use only those current leakage testers or mirroringsystems that comply with ANSIC 101.1 and the Underwriter Laboratory’s specifications (UL1410, 59.7).

DEVICEUNDER

TEST

LEAKAGECURREN T TESTER

TES T ALL EXPOSED ME TAL

SUR FACES

2-WIRE CORD

ALSO TES T WITH PLUG REVERSED

(USING AC ADAPTER PLUG AS REQU IRED)

EARTH GROUND

( R E A D I N G SHOULD NOT BE ABOVE 0.5mA)

Figure 1.1 AC Leakage Test

4) A high voltage is maintained within the specified limits using safety parts, calibration and tolerances. When voltageexceeds the specified limits, check each special part.

5) Warning for Engineering Changes:Never make any changes or additions to the circuit design or the internal part for this product.Ex: Do not add any audio or video accessory connectors. This might cause physical damage.Furthermore, any changes or additions to the original design/engineering will invalidate the warranty.

6) Warning - Hot Chassis:Some TV chassis are directly connected to one end of the AC power cord for electrical reasons. Without insulatedtransformers, the product can only be repaired safely when the chassis is connected to the earthed end of the ACpower source.To make sure the AC power cord is properly connected, follow the instructions below. Use the voltmeter to measure thevoltage between the chassis and the earthed ground. If the measurement is over 1.0V, unplug the AC power cord andchange the polarity before reinserting it. Measure the voltage between the chassis and the ground again.

Copyright© 1995-2011 SAMSUNG. All rights reserved. 1-1

1. Precaution

7) Some TV chassis are shipped with an additional secondary grounding system. The secondary system is adjacent tothe AC power line. These two grounding systems are separated in the circuit using an unbreakable/unchangeableinsulation material.

8) When any parts, material or wiring appear overheated or damaged, replace them with new regular ones immediately.When any damage or overheating is detected, correct this immediately and make a regular check of possible errors.

9) Check for the original shape of the lead, especially that of the antenna wiring, any sharp edges, the AC power and thehigh voltage power. Carefully check if the wiring is too tight, incorrectly placed or loose. Never change the spacebetween the part and the printed circuit board. Check the AC power cord for possible damages. Keep the part or thelead away from any heat-emitting materials.

10) Safety Indication:Some electrical circuits or device related materials require special attention to their safety features, which cannot beviewed by the naked eye. If an original part is replaced with another irregular one, the safety or protective features willbe lost even if the new one has a higher voltage or more watts.Critical safety parts should be bracketed with ( , ). Use only regular parts for replacements (in particular, flameresistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire.

1-2 Copyright© 1995-2011 SAMSUNG. All rights reserved.

1. Precaution

1.2. Servicing Precautions

WARNING

1) First carefully read the “Safety Instruction” in this service manual.When there is a conflict between the service and the safety instructions, follow the safety instruction at all times.

2) Any electrolytic capacitor with the wrong polarity will explode.

1) The service instructions are printed on the cabinet, and should be followed by any service personnel.

2) Make sure to unplug the AC power cord from the power source before starting any repairs.a) Remove or re-install parts or assemblies.b) Disconnect the electric plug or connector, if any.c) Connect the test part in parallel with the electrolytic capacitor.

3) Some parts are placed at a higher position than the printed board. Insulated tubes or tapes are used for this purpose.The internal wiring is clamped using buckles to avoid contact with heat emitting parts. These parts are installed backto their original position.

4) After the repair, make sure to check if the screws, parts or cables are properly installed. Make sure no damage is causedto the repaired part and its surroundings.

5) Check for insulation between the blade of the AC plug and that of any conductive materials (i.e. the metal panel,input terminal, earphone jack, etc).

6) Insulation Check Process:Unplug the power cord from the AC source and turn the switch on. Connect the insulating resistance meter (500V) tothe AC plug blade. The insulating resistance between the blade of the AC plug and that of the conductive materialshould be more than 1MΩ.

7) Any B+ interlock should not be damaged.If the metal heat sink is not properly installed, no connection to the AC power should be made.

8) Make sure the grounding lead of the tester is connected to the chassis ground before connecting to the positive lead.The ground lead of the tester should be removed last.

9) Beware of risks of any current leakage coming into contact with the high-capacity capacitor.

10) The sharp edges of the metal material may cause physical damage, so protect yourself by wearing gloves during therepair.

11) Due to the nature of plasma display panels, partial after-images may appear if a still picture is displayed on the screenfor a long period of time.This is caused by brightness deterioration due to the storage effect of the panel, and to prevent this from happening, werecommend that the brightness and contrast are reduced. (e.g.) Contrast: 25, Brightness: 50


1. Precaution

1.3. Static Electricity Precautions

1) Some semi-conductive (“solid state”) devices are vulnerable to static electricity. These devices are known as ESD.ESD includes the integrated circuit and the field effect transistor. To avoid any materials damage from electrostaticshock, follow the instructions described below.

2) Remove any static electricity from your body by connecting the earth ground before handling any semi-conductive partsor assemblies. Alternatively, wear a dischargeable wrist-belt.(Make sure to remove any static electricity before connecting the power source - this is a safety instruction foravoiding electric shock)

3) Remove the ESD assembly and place it on a conductive surface such as aluminum foil to prevent accumulating staticelectricity.

4) Do not use any Freon-based chemicals. Such chemicals will generate static electricity that causes damage to the ESD.

5) Use only grounded-tip irons for soldering purposes.

6) Use only anti-static solder removal devices.Most solder removal devices do not support an anti-static feature. A solder removal device without an anti-static featurecan store enough static electricity to cause damage to the ESD.

7) Do not remove the ESD from the protective box until the replacement is ready. Most ESD replacements are covered withlead, which will cause a short to the entire unit due to the conductive foam, aluminum foil or other conductive materials.

8) Remove the protective material from the ESD replacement lead immediately after connecting it to the chassis orcircuit assembly.

9) Take extreme caution in handling any uncovered ESD replacements. Actions such as brushing clothes or lifting your legfrom the carpet floor can generate enough static electricity to damage the ESD.

CAUTION

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructionsunless you are qualified to do so.


1. Precaution

1.4. Installation Precautions

1) For safety reasons a minimum of two people are required to carry this product.

2) Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock.

3) Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperaturemay cause fire.

4) Bend the external antenna cable when connecting it to the product. This is a measure to protect it from being exposed tomoisture. Otherwise, it may cause a fire or electric shock.

5) Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Alsocheck the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fireor electric shock.

6) Keep the antenna far away from any high-voltage cables and install it firmly. Contact with the high-voltage cable or theantenna falling over may cause fire or electric shock.

7) When connecting the RF antenna, check for a DTV receiving system and install a separate DTV reception antenna forareas with no DTV signal.

8) When installing the product, leave enough space (4”) between the product and the wall for ventilation purposes. Arise in temperature within the product may cause fire.

9) When moving a PDP with removable speakers, detach the speakers first before moving the main body. Moving the PDPmain body without separating the speakers may cause the speakers to detach, possibly causing damage or injury.


2. Product Specification


2.1. Product Feature

Features

Block Specification Major IC Remark

RF Digital/Analog (DTV Built In)

PDP Module SDI DH MODULE43” HD

51” HDNew Module

PowerSAMSUNG ELECTRO MECHANICS

SMPS DOYANG SMPS

Video

NTSC 3.58 ATSC

HDMI

Component, PC

MSD 2248

Sound SRS TruSuround HD, Dolby Digital TAS 5715 Optical Output

Cabinet C490 Design



Specification

Model P*43D4*0 P*51D4*0

Dimensions (W x H x D)39.8 x 27.5 x 12 inches - with stand

39.8 x 24.5 x 2.2 inches - without stand

46.7 x 30.8 x 12 inches - with stand

46.7 x 27.8 x 2.2 inches - without stand

Weight41.8 lbs - with stand

35.2 lbs - without stand

56.2 lbs - with stand

49.6 lbs - without stand

Panel Resolution 1024 x 768 1360 x 768

PC Resolution 1920 (H) x 1080 (V)

Screen Size 43 Inches (16:9) 51 Inches (16:9)

Power Consumption 43 HD: 200W ±10% and Less 51 HD : 280W ±10% and Less

Antenna InputANT - AIR / CABLE IN

75Ω unbalanced

W/W

AV

COMPONENT1 - 480i / 480p / 720p / 1080i / 1080p

COMPONENT2 - 480i / 480p / 720p / 1080i / 1080p

PC

HDMI1 – 480p / 720p / 1080i / 1080p

HDMI2 (DVI Compatible) – 480p / 720p / 1080i / 1080p

HDMI3 (SIDE AV) – 480p / 720p / 1080i / 1080p

480i can be displayed on HDMI, however it is not contained in EDID data.Video Input

EU

AV

COMPONENT1 - 480i / 480p / 720p / 1080i / 1080p

SCART - 21P, Sn, BLK

PC

HDMI1 – 480p / 720p / 1080i / 1080p

HDMI2 (DVI Compatible) – 480p / 720p / 1080i / 1080p

HDMI3 (SIDE AV) – 480p / 720p / 1080i / 1080p

480i can be displayed on HDMI, however it is not contained in EDID data.

Audio Input

AV

COMPONENT 1 - 480i / 480p / 720p / 1080i / 1080p

COMPONENT 2 - 480i / 480p / 720p / 1080i / 1080p

PC

DVI

Audio Output AUDIO (L/R)

Speaker Output 10W + 10W (40dB + 40dB)

New Features 3D Built-In



2.2. Specifications Analysis

Model P*43D4*0 P*51D4*0 P*42C450*

Design

Display Type PDP TV PDP TV PDP TV

Built-In Tuner O O O

Resolution 1024 x 768 1365 x 768 1024 x 768

PDP Module DH DH U2P

Screen Size 43 inches 51 inches 42 inches

Basic

Picture ratio 16 : 9 16 : 9 16 : 9

Brightness 1,500 Cd/m2 1,500 Cd/m2 1,500 Cd/m2

Contrast Ratio 10,000 : 1 10,000 : 1 30,000 : 1Picture

Picture Enhacer DNIe (SEMS20) DNIe (SEMS20) DNIe

Equalizer 5 Band 5 Band 5 Band

Auto Volume Control O O O

Surround Sound SRS Theater Sound SRS Theater Sound SRS TruSurround HDAudio

Speaker Output 10W + 10W 10W + 10W 10W + 10W

PIP O O O

Double Screen X X X

Caption O O O

Still Image X X X

EPG O O O

My color Control X X X

Energy Saving O O O

Screen Burn Protection O O O

Features

Anynet X X O

Antenna 1 (Cable/Air) 1 (Cable/Air) 1 (Cable/Air)

AV Input 1 Input 1 Input 1 Input

S-Video X X X

W/W 2 Input 2 Input 2 InputComponent

EU 1 Input 1 Input 1 Input

PC (D-SUB) 1 Input 1 Input 1 Input

DVI X X X

HDMID490 – 3 Input

D450 – 2 Input

D490 – 3 Input

D450 – 2 Input4 Input

USB 1 1 1

Sub Woofer X X X

Connections

Optical 1 1 1

Etc. Speaker/Stand Built-in Speaker Built-in Speaker Built-in Speaker



TIP

O : Supported, X : Not Supported

NOTE

For the power supply and power consumption, refer to the label attached to the product.



2.3. Accessories

2.3.1. Supplied Accessories

Accessories Item Item code Remark

A B C D

Remote Control AA59-00484A

Batteries 4301-000103

Power Cord 3903-000456

Owner`sInstructions

BN68-03491C

Cloth-Clean BN63-01798B

Ferrite Core for

Power Cord3301-002049

Samsung ServiceCenter



2.3.2. Sold Separately

Accessories Item Item code Remark

RS232 Cable -

HDMI -

HDMI-DVI -

Component -

Composite (AV) -

Coaxial (RF) -

VGA -

Samsung Service Center


3. Disassembly & Reassembly


3.1. Overall Disassembly & Reassembly

CAUTION

• Be sure to separate the power cord beforedisassembling the unit.

• Discharge the capacitors first when separating PCB’swith high capacity capacitors such as SMPS, XMain Board, Y Main Board, etc. (A spark may begenerated by the electric charge, and there is dangerof electronic shock.)

• Check that the cables are properly connectedreferring to the circuit diagram when disassemblingor assembling the unit taking care not to damage thecables

• Take care not to scratch the Glass Filter in the front.

• Assemble the boards in the reverse order of thedisassembly.

• The plasma must be layed down on a flat paddedsurface for disassembly and reassembly.

1. Place monitor face down on cushioned table. Removescrews from the Stand. Remove stand.* Rear view of 43"

<43" PDP>

<43" PDP>

6001–002621 : M4 * L8



* Rear view of 51"

<51" PDP>

<51" PDP>

6001–002621 : M4 * L8

2. Remove the screws of rear-cover.* Rear view of 43"

<43" PDP>

6003–001782 : M4 * L12

6003–000337 : M4 * L10

* Rear view of 51"

<51" PDP>

6003–001782 : M4 * L12

6003–000337 : M4 * L10



3. Lift up and remove the rear-cover.* Rear view of 43"

<43" PDP>

* Rear view of 51"

<51" PDP>

4. Remove the screws of main board.

CAUTION

Disconnect all connectors prior to removing boards.

6001–002606 : M3 * L10

5. Remove the screws of SMPS. Remove the SMPS.

CAUTION

Align board under tab when re-installing.

6001–002606 : M3 * L10

6003–001439 : M4 * L8

6. Remove the speakers. (R/L)



7. Remove the Cover Bottom.

8. Remove the screw of Bluetooth Module.

NOTE

PD49X Series Only.

6001–002606 : M3 * L10

9. Remove the screws of Bracket Stand Link. Lift up theStand Bracket Stand Link.

6003–001782 : M4 * L12

6003–000337 : M4 * L10

10. Remove the screws of the front-cover.* Rear view of 43"

<43" PDP>

6003–001782 : M4 * L12

* Rear view of 51"

<51" PDP>

6003–001782 : M4 * L12



3.2. Method for Disassembly of Function Assy

1. Put up the upper Locking, Use screwdriver.

2. Put up the lower Locking, Use screwdriver.

3. Remove Locking.

4. Detach the Function PBA.

CAUTION

Disconnect all connectors prior to removing boards.


4. Troubleshooting

4. Troubleshooting

4.1. Checkpoints by Error Mode

4.1.1. First Checklist for Troubleshooting

1) Check the various cable connections first.

• Check to see if there is a burnt or damaged cable.

• Check to see if there is a disconnected or loose cable connection.

• Check to see if the cables are connected according to the connection diagram.

2) Check the power input to the Main Board.

3) How to distinguish if the problem is caused by Main board or Logic Board.

• No Video : If the problem is No Video but Logic Board is on and Indication LED is blinking repeatedly andfaster than normal booting, replace the T-Con board.

• Distorted Picture : Check the inner patterns.

Inner pattern Picture Problem

OK NG Main board

NG NG Main or LVDS cable or Logic Board or Panel.

• How to check inner pattern?a. Factory mode (mute → 1 → 8 → 2 → Power on when TV is in ‘stand - by mode’ )b. Move to SVC menu.c. Move to Test Pattern.d. Check inner patterns.


4. Troubleshooting

4.1.2. Checkpoints by Error Mode

No Power

Symptom

• The LEDs on the front panel do not work when connecting the power cord.• The SMPS relay does not work when connecting the power cord.• The unit appears to be dead.

Major Checklist

The SMPS relay or the LEDs on the front panel does not work when connecting the power cord ifthe cables are improperly connected or the Main Board or SMPS is not functioning. In this case,check the following:

• Check the internal cable connection status inside the unit.• Check the fuses of each part.• Check the output voltages of the SMPS.• Replace the Main Board.

Diagnostics

FuseCN801

CN201

<43" PDP>

FuseCN801

CN201

<51" PDP>


4. Troubleshooting

Yes

Yes

Yes

Yes

Power indica tor LED is on? Check AC power connection.

Replace the Main Board.

Connect the cable be tweenCN801 and CN201 connector.

Are the SMPS CN801 and Main CN201connected?

Replace Fuse . (F801S)Is th e Fuse(F801S) of the SMPS Power

Input Part Open?

Replace the SMPS.SMPS CN801PIN2 : STB5V

PIN1_ PS ON : Check to see if it is 0V?

No

No

No

No

CAUTION

Make sure to disconnect the power before working on the SMPS board.


4. Troubleshooting

No Video

Symptom • Audio is normal but no picture is displayed on the screen.

Major Checklist• The output voltage of the Main SMPS.• This may happen when the LVDS cable connecting the Main Board and the Panel is

disconnected.

Diagnostics

LVDS cable

<43" PDP>

LVDS cable

<51" PDP>


4. Troubleshooting

Check the LEDOperation.

Yes

Yes

Yes

Replace the Main Board.

Check / Replace the LVDS Cable .Check the LVDS connector.

Is it connected correctly?

Replace the SMPS.Check All output voltages on SMPS.

Are a ll voltages normal?

Replace the Logic Board.Check the LED opera tion of Logic Board

whitch is normally opera ting?(Normal : Blink once a second)

No

No

No

CAUTION

Make sure to disconnect the power before working on the SMPS board.


4. Troubleshooting

No Sound

Symptom • Video is normal but there is no sound.

Major Checklist

• When the speaker connectors are disconnected or damaged.• When the sound processing part of the Main Board is not functioning.• Speaker defect.• SMPS not supplying voltage to the main board.

Diagnostics <43" PDP>

Speaker

Speaker cable

CN801

<51" PDP>


4. Troubleshooting

Yes

Yes

Yes

Replace the Speaker.

Replace the SMPS.Is th e output voltage of SMPS normal?

(CN801 7pin : 15V)

Replace the Main board.

(1)Is the speaker output te rmina l of

the Main board normal?

Connect the cable properly orreplace the cable, if necessary.

Is the cable connection be tweenMain board and the speaker

properly connected?

No

No

No

Sound Output Shape

(1)

CAUTION

Make sure to disconnect the power before working on the IP board.


4. Troubleshooting

4.1.3. Faults and Corrective Actions

Symptom Related Image Causes and Countermeasures

A blank vertical cell (block)appears on the screen.

• Address buffer defect• Replace the corresponding upper/lower buffers.

(E, F or G)• COF defect (burnt)

• Replace the module.

A green screen appears whenthe TV is turned on.

• The Scale is not reseting.• Replace the Main board.

The OSD box appears butthere is no text.

• Incorrect program version.• Check the version of each program.• Replace the Main board.

A blank upper (or lower)block appears on the screen.

• Upper/Lower Y Buffer defect• Replace the corresponding upper/ lower buffers.

Either the main or sub picturedoes not appear.

• Replace the Main board.

A vertical green line appearson the screen.

• The SMPS voltage is incorrect.• Adjust the SMPS voltage according to the voltage

printed on the module label.


4. Troubleshooting

Symptom Related Image Causes and Countermeasures

Dim screen (blurred in red)• X-Main board defect

• Replace the X-Main board.

A blank screen appears. • Replace the Y-Main board.


4. Troubleshooting

4.1.4. Operating Logic LED

Normal

• LED ON/OFF for 0.5s

OFF

ON

P ower ON Logic ON S equence (P OS ) Normal Toggling (eve ry 32 Vsync)

-. NT : 534 ms-. P AL : 640 ms

Abnormal

• LED ON/OFF three times for 8.1s

540ms

8 .06 s ec

Exception

540ms

540ms

540ms

540ms27Mhz

2.44s ec

163msP LL ON

163ms

163ms

163ms

163ms

·· ªª µµ ªª ¦¦ ¹¹ee ...

·· ªª µµ ªª ¦¦ ¹¹ee ...

DRV_RESET

• LED ON for 5s and LED OFF for 2s

5 s ec

·· ªª µµ ªª ¦¦ ¹¹ee ...

DRV_RES ET

2 s ec


4. Troubleshooting

4.1.5. Adjust Function Key Sensitivity

1) Select 'Factory'

2) Select 'Control'


4. Troubleshooting

3) Select 'Sub Option'

4) Select 'Key Sensitivity'


4. Troubleshooting

5) Default value (PD490=56, PD550=32)

6) Adjust The Value of Key Sensitivity

No use 'Key Sens itivity' Very Sensitive Insensitive


4. Troubleshooting

4.1.6. Function Assy Pin Map

US Main Board

CN1201

Pinmap

1. IR

2. GND

3. A3.3V

4. SCL

5. SDA

6. FUNC_INTR

7. LED_STB

EU Main Board

CN1201

Pinmap

1. IR

2. GND

3. A3.3V

4. SCL

5. SDA

6. FUNC_INTR

7. LED_STB


4. Troubleshooting

4.1.7. Adjust SMPS Voltage when change SMPS

VS_TP

VS_VR

VA_TP

VA_VR

VS_TP

VS_VR

VA_TP

VA_VR

TIP

• T.P : Test Point

• V.R : Variable Resistor


4. Troubleshooting

4.2. Factory Mode Adjustments

4.2.1. Entering Factory Mode

To enter ‘Service Mode’ Press the remote-control keys in this sequence.

• If you do not have Factory remote-control.

¾¾ ÆÆ ´ ÁÁoo oo ¾¾ ÆÆ ´ ÁÁoo ¤¤ oo ¤¤ ¤¤ ££ oo

¾¾ ÆÆ ´ ÁÁoo oo ¾¾ ÆÆ ´ ÁÁoo ¤¤ ££ oo¦¦ ~~ ¦¦

• If you have Factory remote-control.

INFO Factory

• If you don’t have Factory remote control, can’t control some menu.

OptionControlSVCExpertADC / WBAdvancedT-MST4AUSC-0408.0

T-MST4AUSS-0019

E-Manual : X6ATSCA-0003

EDID SUCCESS

HDCP SUCCESS

CALIB : AV O COMP O PC O HMDI O

Option : 2701, 1374

SDAL-0.58.1.0

RFS : "Mstar-X5 0039"

KERNEL MODULE VERSION: "00035_90"

2010-12-08

Type : 51DFHcD

Model : PN51D550

MAC SUCCESS

LOCD X

Factory Data Ver : 68

EERC Version : 501

DTP-AP-COMP-582

DTP-BP-HAL-0083

DTP-BP-0582

Date of purchase : mm/dd/yyyy


4. Troubleshooting

4.2.2. Factory Data

Option

Item Data Remark

Factory Reset -

Type 43DHHcD

Local Set xx

Model PD490

Tuner xx

Ch table NONE

Front Color T-R-BLK

Control

Menu Item Data Remark

EDID EDID ON/OFF ON

EDID WRITE ALL Success

EDID WRITE PC Success

EDID WRITE HDMI ...

EDID WRITE HDMI1 Success




HDMI EDID Ver HDMI 1.2

HDMI EDID Port NONE

EDID WRITE DVI ...

Sub Option RF Mute Time 600ms

RS-232 Jack Debug

Watchdog OFF

WD COUNT 255

Dimm Type

LVDS FORMAT PDP

Language_Arabic xx

TOOLS Support 32

LNA Support 0

DB On with5MB

MOVIE chapterinmed

DLNA ON

MediaPlay

Play List OFF

NETWORK Support Ext-Wifi

Info Link Server Type development


4. Troubleshooting


Info Link Country None

TTX List

TTX Group

24Px4 Support OFF

Power Indicator Support OFF

BD Wise Support OFF

Data Service Support OFF

OTA Duration Test OFF

Alternate Del OFF

OTN Server Type operating

OTN Test Server OFF

OTN Support ON

OTN Reset

OTN Duration OFF

OTN Fail Test OFF

IIC BUS STOP OFF

Visual Test Disable

Emergency Log Copy

Checksum 0x0000

Select Log Type IR KEY

Log View

View Log

Delete Log

ColorSpace Support RGB Type

Gemstar On/Off OFF

WSS Support OFF

PVR Support OFF

CI Support OFF

Eepron Reset

LVDS Spread ON

Period 40K

Amplitude 1.5

Spread Spectrum

DDR Spread 1.0% Spread

A CTRL_OFFSET_0_3 0x0

A CTRL_OFFSET_D 0x0

B CTRL_OFFSET_0_3 0x0

DDR Margin

B CTRL_OFFSET_D 0x0

H.264 Margin 8

MPEG Margin 1000

Tuner Margin 10


4. Troubleshooting


Y0 Ref 165

Y1 Ref 148

Y2 Ref 119

Y3 Ref 101

Y4 Ref 76

Y5 Ref 60

Y6 Ref 31

Y7 Ref 0

Cb0 Ref 128

Cb1 Ref 64

Cb2 Ref 148

Cb3 Ref 85

Cb4 Ref 171

Cb5 Ref 108

Cb6 Ref 194

Cb7 Ref 0

Cr0 Ref 128

Cr1 Ref 137

Cr2 Ref 64

Cr3 Ref 74

Cr4 Ref 181

Cr5 Ref 192

Cr6 Ref 118

SST

Cr7 Ref 0

Y0 TH 20

Y1 TH 20

Y2 TH 20

Y3 TH 20

Y4 TH 20

Y5 TH 20

Y6 TH 20

Y7 TH 20

Cb0 TH 20

Cb1 TH 20

Cb2 TH 20

Cb3 TH 20

Cb4 TH 20

Cb5 TH 20

Cb6 TH 20

Cb7 TH 20

SST_TH


4. Troubleshooting


Cr0 TH 20

Cr1 TH 20

Cr2 TH 20

Cr3 TH 20

Cr4 TH 20

Cr5 TH 20

Cr6 TH 20

Cr7 TH 20

2nd mips ON

2nd mips count 0

Region xxx

PnP Language xxx

PC Auto Ident Enable

OTP Lock ...

Auto Power MEMORY

KEY SENSITIVITY 56 1(Very Sensitive)~255(Insensitive)

FANET OFF

OTA Support OFF

WIFI REGION V

FKP Down

PDP Option LOGIC CONNECT OFF

PIXEL SHIFT TEST OFF

PANEL VERSION DF

PANEL INCH 51FHD

PANEL TYPE 53

PANEL TEMPERATURE 40

LOGIC ID A712

LOGIC SW VERSION 2010-11-20

LOGIC SW CHECKSUM 0xFC31

MRT 44

SAPC TIMER ON

APC SPEED SLOW

Real 100 Hz Support OFF

XGA Resolution OFF

PLG_SHOP 128

Hotel Option HOTEL MODE ON

POWER ON CHANNELEN

UserDefined

POWER ON CHANNEL 3

CHANNEL TYPE CATV


4. Troubleshooting


POWER ON VOLUMEEN

UserDefined

POWER ON VOLUME 10

MIN VOLUME 0

MAX VOLUME 100

PANEL BUTTON LOCK Unlock

POWER ON SOURCE TV

Picture Menu Lock OFF

Music Mode AV OFF

Music Mode PC OFF

Music Mode Comp OFF

Music Mode Backlight OFF

Menu Display ON

Power On Option Last Option

Auto Source OFF

Energy Saving OFF

Clone TV to USB

Clone USB to TV

Setting Auto initialize OFF

SIRCH Update Time 2:00 AM

MONITOR OUT CVBS ON

Shop Option Shop Mode OFF

Exhibition Mode OFF

Asia Option TTX OFF

China HD OFF

NT Conversion OFF

Sepco 120Hz OFF

Unbalance OFF

FMTransmitter Support OFF

FMTransmitter Carrier OFF

AF Level adjust 3

TX power Level 0

Mono Last Memory OFF

H Shaking OFF

SOUND High Devi OFF

Carrier Mute ON

Volume Curve Type1

Speaker Delay Normal 50

Pilot Level High Thld 0x28h

Pilot Level Low Thld 0x10h

FM Prescale 0


4. Troubleshooting


AM Prescale 0

NICAM Prescale 0

Amp Volume 0xc7h

Amp Scale 0x82h

Woofer Type 1

Woofer Scale 0x7fh

Woofer Check Sum

Speaker EQ ON

Amp Model 0

Speaker cut-off Freq NTP7411

SPDIF PCM Gain -9 dB

FM M Prescale 48

BTSC Mono Prescale 25

BTSC stereo Prescale 47

SAP Prescale 43

A2 Ident High Thld 31

A2 Ident Low Thld 2

Carrier2 Amp High Thld 4

Carrier2 Amp Low Thld 3

Carrier2 SNR High THR 16

Carrier2 SNR Low THR 80

Audio-IP Test Ready

TruBass-Checksum 0x200190E2

PWM Mode BD

ConfigOption Num of ATV 1

Num of DTV 1

Num of AV 1

Num of SVIDEO 0

Num of COMP 2

Num of HDMI 4

Num of PC 1

Num of SCART 0

Num of DVI 0

Num of OPTICAL Link 0

Num of MEDIA 1

Num of PANEL KEY 6

Num of USB Port 2

Num of HeadPhone 0


4. Troubleshooting


Num of RVU 0

MFT Offset 62.5

Select LCD/PDP PDP

HDMI/DVI SEL 1

Indicator Led OFF

Wall Mount OFF

HV Flip OFF

Num Of Display 2

DVI/HDMI SOUND Auto

HDMI HOT PLUG Disable

HOTPLUG SWITCHING Boot

HOT PLUG DURATION 1200ms

CLK TERM DURATION 1200ms

HDMI FLT CNT SIG 100ms

HDMI FLT CNT LOS 100ms

UNSTABLE BAN CNT 3500ms

HDMI Err Cnt 1

HDMI ROBIN ON

HDMI Callback OFF

HDMI CTS Thld 8

HDMI CTS Cnt1 1

TMDS_EQ2_Boost 1

TMDS_EQ2_Gain 0

TMDS_PLL_Loop 3

TMDS_CPREG_BLEED 1

HDMI EQ Auto

HDMI EDID wRITE Type Separate

HDMI Switch NONE

DVI SET TIME 300ms

Type Of PANEL KEY PDPVertical

EcoSensor Support ON

LEDMotionPlus Support OFF

Natural Mode Support OFF

All Share Support ON


4. Troubleshooting


Relax Mode Support OFF

DVI-I Support

Melfas Function Support

Light Level Support

H Write

HDMI Sync DE

HeadPhone Port A Out2

SCC SCC Mode Dynamic

SCC ON/OFF OFF

Hx 272

Hy 278

Lx 272

SCC Input Data

Ly 278

sSCC Hx 550

sSCC Hy 566

sSCC Lx 598

sSCC Const

sSCC Ly 550

pSCC Hx 550

pSCC Hy 566

pSCC Lx 598

pSCC Const

pSCC Ly 550

SCC Source Data PBA

SWAP PBA


4. Troubleshooting

SVC


Test Pattern Pattern Sel ...

LOGIC Pattern Sel 0

LOGIC Level Sel 255

Panel Auto Setting Failure

PANEL DISPLAYTIME

2Hr

LOGIC USB D/L off

Tuner Status

T-CON USBDownload

Failure

MICOMUPGRADE

Off

BT ADDRESS e4e0c53197db

BT UPGRADE

SVC Reset

Expert


N/D ADJ OFF

Source ...

ADC/WB


ADC AV Calibration

Comp Calibraion

PC Calibration

HDMI Calibration

ADC Target 1st_AV_Low 64

1st_AV_High 880

1st_AV_Delta 2

1st_COMP_Y_Low 64

1st_COMP_Cb_Low 512

1st_COMP_Cr_Low 512

1st_COMP_Y_High 940

1st_COMP_Cb_High 512

1st_COMP_Cr_High 512

1st_COMP_Delta 2

1st_PC_Low 4

1st_PC_High 1004


4. Troubleshooting


1st_PC_Delta 2

2nd_ACH_Low 4

2nd_ACH_High 940

2nd_PC_Low 4

2nd_PC_High 940

2nd_Delta 2

ADC Result 1st_Y_GH 258

1st_Y_GL 128

1st_Cb_BH

1st_Cb_BL

1st_Cr_RH

1st_Cr_RL

2nd_R_L 133

2nd_G_L 133

2nd_B_L 133

2nd_R_H 70

2nd_G_H 70

2nd_B_H 70

White Balance Sub Brightness 128

R-Offset 128

G-Offset 128

B-Offset 128

Sub Contrast 128

R-Gain 128

G-Gain 128

B-Gain 128

Movie R-Offset

Movie B-Offset

Movie R-Gain

Movie B-Gain

Advanced

• Picture_2D


Sub Setting Gamma 0.95

Natural Gamma 0

Pwm Max 100

PWM Min 0

Pwm Mid 0

Contrast Dimming OFF


4. Troubleshooting


7.5 IRE NTSC OFF

7.5 IRE Offset

Comp Phase 110

Led Peak OnOff OFF

Dither Bypass OFF

D Motion Light On

Dynamic Contrast On

EPA Standard Standard Contrast 100

Standard Brightness 45

Standard Sharpness 50

Standard Color 50

Standard Tint 0

Standard Backlight 10

WB Movie W/B Movie On/Off OFF

Model ...

Color Tone ...

Msub Brightness ...

Msub Contrast ...

N_Rgain ...

N_Bgain ...

N_Roffset ...

N_boffset ...

W2_Rgain ...

W2_Bgain ...

W2_Roffset ...

W2_Boffset ...

Movie Contrast ...

Movie Bright ...

Movie Color ...

Movie Sharpness ...

Movie Tint ...

Movie Backlight ...

Movie Gamma ...

M_Sub_Gamma ...

HDMI Black Level ...

WCE WRHue 64

WRSat 16

WYHue 64

WYSat 16

WGHue 64


4. Troubleshooting


WGSat 16

WCHue 64

WCSat 16

WBHue 64

WBSat 16

WMHue 64

WMSat 16

ARHue 64

ARSat 16

AYHue 64

AYSat 16

AGHue 64

AGSat 16

ACHUE 64

ACSat 16

ABHue 64

ABSat 16

AMHue 64

AMSat 16

VDEC AGC mode 3

AGC manual gain 72

Ifcomptype 1

Ifcompsel 15

Saturain Cb/Cr 145

Secam Filter Sel 0

RGB Delay 150

Peaking Gain 0

Coring Gain 3

Chroma Peak 10

2D V Peaking 0

2D H Peaking 0

2D Peaking Gain 0

Sharpness Post_H1 20

Post_H2 26

Post_H3 20

Post_H4 15

Post_v1 20

Post_v2 18

Post_H2 Overshoot 128

Post_H2 Undershoot 128


4. Troubleshooting


Post_H3 Overshoot 128

Post_H3 undershoot 128

Core Gain1 2

CoreGain2 3

D_Tot_Gain 24

S_Tot_Gain 24

ColorMapping A_Red_R 60

A_Red_G 0

A_Red_B 0

A_Green_R 67

A_Green_G 100

A_Green_B 0

A_Blue_R 0

A_Blue_G 49

A_Blue_B 100

A_Yellow_R 100

A_Yellow_G 100

A_Yellow_B 0

A_Cyan_R 0

A_Cyan_G 46

A_Cyan_B 100

A_Magenta_R 27

A_Magenta_G 0

A_Magenta_B 67

N_Red_R 50

N_Red_G 0

N_Red_B 0

N_Green_R 0

N_Green_G 50

N_Green_B 0

N_Blue_R 0

N_Blue_G 0

N_Blue_B 50

N_Yellow_R 50

N_Yellow_G 50

N_Yellow_B 0

N_Cyan_R 0

N_Cyan_G 50

N_Cyan_B 50

N_Magenta_R 50


4. Troubleshooting


N_Magenta_G 0

N_Magenta_B 50

Enhance BLE_Gain 22

D Sub Color 80

D Skin Hue 84

D Skin Sat 18

S Sub Color 80

S Skin Hue 72

S Skin Sat 16

M Sub Color 55

M Skin Hue 64

M Skin Sat 16

Sub Tint 45

CE_Normal_Left_Gain 35

CE_Normal_Right_Gain 20

CE_Normal_Offset -10

CE_Special_Left_Gain 15

CE_Special_Right_Gain 10

CE_Special_Offset -50

CE_S_Left_gain 10

CE_S_Right_Gain 40

CE_S_Normal_Offset -2

LNA_Plus Synctip_Noise 102

dB01_th 3

dB12_th 4

dB23_th 6

dB34_th 8

dB45_th 10

dB56_th 12

dB67_th 15

dB78_th 28

LNA_Plus_Yfiller 3

YC_Delay RF PAL BG 10

RF PAL DK 11

RF PAL I 13

RF PAL M 6

RF PAL n 11

RF SECAM BG 5

RF SECAM DK 8

RF SECAM L 8


4. Troubleshooting


RF NT 358 14

RF NT 443 8

AV PAL 9

AV PAL M 7

AV PAL N 9

AV SECAM 9

AV NT 358 10

AV NT 443 4

AV Pal 60 6

SCART PAL 9

SCART PAL M 9

SCART PAL N 9

SCART SECAM 4

SCART NT 358 10

SCART NT 443 4

SCART PAL 60 6

SCART RGB PAL 8

SCART RGB PAL M 8

SCART RGB PAL N 8

SCART RGB SECAM 8

SCARTRGB NT 358 8

SCARTRGB NT 443 8

SCARTRGB PAL 60 8

Picture Update

• Picture_3D


Sub Setting_3D 3D_Gamma 0.95

3D_Natural Gamma 0

3D_Pwm Max 100

3D_PWM Min 0

3D_Pwm Mid 0

3D_ContrastDimming

OFF

3D_Led PeakOnOff

OFF

3D_Dither Bypass OFF

3D_D Motion Light OFF

3D_DynamicContrast

OFF

EPA_3D 3D Contrast 100


4. Troubleshooting


3D Brightness 45

3D StandardSharpness

50

3D Standard Color 50

3D Standard Tint 0

3D StandardBacklight

7

WB Movie_3D 3D_W/B MovieOn/Off

OFF

3D_Model ...

3D_Color Tone ...

3D_MsubBrightness

...

3D_Msub Contrast ...

3D_C_Rgain ...

3D_C_Bgain ...

3D_C_Roffset ...

3D_C_boffset ...

3D_N_Rgain ...

3D_N_Bgain ...

3D_N_Roffset ...

3D_n_Boffset ...

3D_W2_Rgain

3D_W2_Bgain

3D_W2_Roffset

3D_W2_Boffset

3D_Movie Contrast ...

3D_Movie Bright ...

3D_Movie Color ...

3D_MovieSharpness

...

3D_Movie Tint ...

3D_MovieBacklight

...

3D_Movie Gamma ...

3D_M_Sub_Gamma ...

3D_HDMI BlackLevel

...

3D_Sub Contrast 128

3D_Sub_Brightness 128

WCE_3D 3D_WRHue 64

3D_WRSat 17


4. Troubleshooting


3D_WYHue 72

3D_WYSat 17

3D_WGHue 47

3D_WGSat 17

3D_WCHue 58

3D_WCSat 17

3D_WBHue 54

3D_WBSat 18

3D_WMHue 64

3D_WMSat 17

3D_ARHue 64

3D_ARSat 16

3D_AYHue 64

3D_AYSat 16

3D_AGHue 64

3D_AGSat 16

3D_ACHUE 64

3D_ACSat 16

3D_ABHue 64

3D_ABSat 16

3D_AMHue 64

3D_AMSat 16

ColorMapping_3D 3D_A_Red_R 50

3D_A_Red_G 0

3D_A_Red_B 0

3D_A_Green_R 0

3D_A_Green_G 50

3D_A_Green_B 0

3D_A_Blue_R 0

3D_A_Blue_G 0

3D_A_Blue_B 50

3D_A_Yellow_R 50

3D_A_Yellow_G 50

3D_A_Yellow_B 0

3D_A_Cyan_R 0

3D_A_Cyan_G 50

3D_A_Cyan_B 50

3D_A_Magenta_R 50

3D_A_Magenta_G 0

3D_A_Magenta_B 50


4. Troubleshooting


3D_N_Red_R 50

3D_N_Red_G 0

3D_N_Red_B 0

3D_N_Green_R 0

3D_N_Green_G 50

3D_N_Green_B 0

3D_N_Blue_R 0

3D_N_Blue_G 0

3D_N_Blue_B 50

3D_N_Yellow_R 50

3D_N_Yellow_G 50

3D_N_Yellow_B 0

3D_N_Cyan_R 0

3D_N_Cyan_G 50

3D_N_Cyan_B 50

3D_N_Magenta_R 50

3D_N_Magenta_G 0

3D_N_Magenta_B 50

Sharpness_3D 3D_Post_H1 16

3D_Post_H2 10

3D_Post_H3 10

3D_Post_H4 10

3D_Post_v1 20

3D_Post_v2 14

3D_Post_H2Overshoot

32

3D_Post_H2Undershoot

32

3D_Post_H3Overshoot

16

3D_Post_H3undershoot

16

3D_Core Gain1 1

3D_CoreGain2 2

3D_D_Tot_Gain 28

3D_S_Tot_Gain 28

Enhance_3D 3D_BLE_Gain 22

3D_D Sub Color 65

3D_D Skin Hue 100

3D_D Skin Sat 18

3D_S Sub Color 65


4. Troubleshooting


3D_S Skin Hue 72

3D_S Skin Sat 16

3D_M Sub Color 55

3D_M Skin Hue 64

3D_M Skin Sat 16

3D_Sub Tint 50

3D_CE_Normal_Left_Gain 20

3D_CE_Normal_Right_Gain 30

3D_CE_Normal_Offset -10

3D_CE_Special_Left_Gain 15

3D_CE_Special_Right_Gain 10

3D_CE_Special_Offset -50

3D_CE_S_Left_gain 10

3D_CE_S_Right_Gain 40

3D_CE_S_Normal_Offset -2

3D Setting BTPairDis_Ho 2

BTPairDis_sh 25

BTTransDis 10

BTSlaveDelay48 0

BTSlaveDelay50 0

BTSlaveDelay60 0

BTEmiDel_48 0

BTEmiDel_50 0

BTEmiDel_60 0

BTGlsDUTY 100

IREmiDel_48 0

IREmiDel_50 0

IREmiDel_60 0

IREmiMask 1

IRMASKPRD 1

IREmiNum 1

SlavDelay48 0

SlavDelay50 0

LED_BT_IR

SlavDelay60 0


4. Troubleshooting


BTPairDis_Ho_PDP 2

BTPairDis_sh_PDP 25

BTTransDis_PDP 10

BTSlaveDelay48_D 0

BTSlaveDelay50_D 0

BTSlaveDelay60_D 0

BTGlsDUTY_D 100

BTEmiDel_48_S 0

BTEmiDel_50_S 0

BTEmiDel_60_S 0

BTGlsDUTY_S 100

IREmiDel_48_R 0

IREmiDel_50_R 0

IREmiDel_60_R 0

BTGlsDUTY_R 100

BTEmiDel_48_M 0

BTEmiDel_50_M 0

BTEmiDel_60_M 0

BTGlsDUTY_M 100

IREmiMask_PDP 1

IRMASKPRD_PDP 1

IREmiNum_PDP 1

SlavDelay48_PDP 0

SlavDelay50_PDP 0

PDP_BT_IR

SlavDelay60_PDP 0

PDuty192 25

PDuty200 25

PDuty240_Dyn 25

Duty

PDuty210_Mov 25

Glmit_LBT0 88

Glmit_LBT1 89

Glmit_LBT2 90

Glmit_LBT3 91

Glmit_LLT0 95

Glmit_LLT1 96

Glmit_LLT2 97

Glmit_LLT3 98

DCCX1 0

DCCX2 0

DCCX3 0

Dcc


4. Troubleshooting


DCCY1 0

DCCY2 0

DCCH1 0

DCCH2 0

DCCH3 0

DCCV1 0

DCCV2 0

Temp Read 0

Time_HOT 120

Time_Cold 120

Temp_ST 16

Temp_TH 40

delta 5

Depth_Min 10

Depth_Max 100

Viewp_Min_2D3D 64

Viewp_Max_2D3D 192

Viewpoint_Min 64

Effect

viewpoint_Max 192

Debug OFF

DccMode 0

DccSele0_0 0

DccSele0_1 0

DccSele0_2 0

DccSele0_3 0

DccSele0_4 0

DccSele0_5 0

DccSele0_6 0

DccSele0_7 0

PosiSel_0_0 0

PosiSel_0_1 0

PosiSel_0_2 0

PosiSel_0_3 0

PosiSel_0_4 0

PosiSel_0_5 0

PosiSel_0_6 0

PosiSel_0_7 0

PosiSel_0_8 0

PosiSel_0_9 0

PosiSel_0_10 0

Debug


4. Troubleshooting


PosiSel_0_11 0

Bypass OFF


4. Troubleshooting

4.3. Service Adjustment

- You must perform Calibration in the Lattice Pattern before adjusting the White Balance.

White Balance - Calibration

• Factory

ADC / WB AV Calibration

Comp Calibration

PC Calibration

HDMI Calibration

Color Calibration

• Adjust spec.

1) Source : HDMI

2) Setting Mode : 1280*720@60Hz

3) Pattern : Pattern #24 (Chess Pattern)

4) Use Equipment : CA210 & Master MSPG925 GeneratorUse other equipment only after comparing The result with that of The Master equipment.

Input mode Calibration Pattern

CVBS IN (Model_#1) Perform in NTSC/PAL B&W Pattern #24 Lattice

Component IN (Model_#6) Perform in 720p B&W Pattern #24 Lattice

PC Analog IN (Model_#21) Perform in VESA XGA (1024x768) B&W Pattern #24 Lattice

HDMI IN Perform in 720p B&W Pattern #24 Lattice


4. Troubleshooting

• Method of Color Calibration (AV)

1) Apply the NTSC/PAL Lattice (N0. 3) pattern signal to the AV IN 1 port.

2) Press the Source key to switch to “AV1” mode.

3) Enter Service mode.

4) Select the “ADC” menu.

5) Select the “AV Calibration” menu.

6) In “AV Calibration Off” status, press the “ ” key to perform Calibration.

7) When Calibration is complete, it returns to the high-level menu.

8) You can see the change of the “AV Calibration” status from Failure to Success.

• Method of Color Calibration (Component)

1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port.

2) Press the Source key to switch to “Component1” mode.



5) Select the “Comp Calibration” menu.

6) In “Comp Calibration Off” status, press the “ ” key to perform Calibration.


8) You can see the change of the “Comp Calibration” status from Failure to Success.

• Method of Color Calibration (PC)

1) Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port.

2) Press the Source key to switch to “PC” mode.



5) Select the “PC Calibration” menu.

6) In “PC Calibration Off” status, press the “ ” key to perform Calibration.


8) You can see the change of the “PC Calibration” status from Failure to Success.


4. Troubleshooting

• Method of Color Calibration (HDMI)

1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port.

2) Press the Source key to switch to “HDMI1” mode.



5) Select the “HDMI Calibration” menu.

6) In “HDMI Calibration Off” status, press the “ ” key to perform Calibration.


8) You can see the change of the “HDMI Calibration” status from Failure to Success.

White Balance - Adjustment

ADC / WB - White Balance

Factory (Low light) (High light)

Sub Bright

R offset

G offset

B offset

Sub Contrast

R gain

G gain

B gain


4. Troubleshooting

4.4. Software Upgrade

Samsung may offer upgrades for the TV’s firmware in the future.

These upgrades can be performed via the TV when it is connected to the Internet, or by downloading the new firmwarefrom samsung.com to a USB memory device.

• Alternative Software (Backup) shows The previous version that will be replaced.

• Software is represented as ‘Year/Month/Day_Version’.The more recent the date, the newer the software version.Installing the latest version is recommended.

By USB

Insert a USB drive containing the firmware upgrade downloaded from samsung.com into the TV. Please be careful to notdisconnect the power or remove the USB drive while upgrades are being applied.

The TV will turn off and turn on automatically after completing the firmware upgrade. Please check the firmware versionafter the upgrades are complete (the new version will have a higher number than the older version). have a higher numberthan the older version) made will return to their default (factory) settings.

We recommend you write down your settings so that you can easily reset them after the upgrade.


4. Troubleshooting

By Online

Upgrades the software using the Internet.

• First, configure your network. For detailed procedures on using the Network Setting.

Refer to the ‘Setting the Network’ instructions.

• If The internet connection doesn’t operate properly, connection can be broken, please retry downloading.

If the problem still happens, download by USB and upgrade.

Alternative Software (Backup)

If there is an issue with the new firmware and it is affecting operation, you can change the software to the previous.

• If Software was changed, existing Software is displayed.

• You can change current Software to Alternative Software by ‘Alternative Software’.


5. Wiring Diagram

5. Wiring Diagram

5.1. Overall Wiring

43" HD Overall Wiring

CN5500

CN5501

CN5502

CN5503

CN5504

CN5505

CN5009

CN5010

CN5011

Y-DRIVE

SMPSX-DRIVE

MAIN BOARD

LOGIC BOARD

E-BUFFER

CN4000

CN4002

FUNCTIONBLUETOOTH SPEAKER

CN5003 CN5000

CN800S

CN5002

CN5001

CN804

CN801

CN802

CNXX

CN4004

CN2501 CN2500 CN2600

CN2502 CN2601

CN201

CN1201CN1602_HD

CN302

CN1

F-BUFFER

CN603_3DCN2021CN2001

CN2010 CN2009

CN2023CN2022

1

2

3

4

5

6

7

.. ¤¤ ££ ££ oo oo §§ oo ¢¢ ´ ÁÁ ¸´ ÂÂ oo ½½ »»ÈÈ oo


5. Wiring Diagram

51" HD Overall Wiring

CN5505

CN5504

CN5503

CN5500

CN5501

CN5502

CN5002

CN5004

CN5003

CN5005

Y-DRIVE

X-DRIVESMPS

MAIN BOARD

LOGIC BOARD

E-BUFFER

CN4906

CN4404

CN4406

CN4904

FUNCTIONBLUE TOOTH SPEAKER

CN5001 CN5000

CN800S

CN5006

CN5007

CN804

CN801

CN802

CN4701

CN4001

CN2501 CN2500 CN2600

CN2502 CN2601

CN201

CN1201CN1602_HD

CN302

CN1

F-BUFFER

CN603_3DCN2021CN2002

CN2010 CN2011

CN2023CN2022

1

2

3

4

5

6

7

.. ¤¤ ££ ££ oo oo §§ oo ¢¢ ´ ÁÁ ¸´ ÂÂ oo ½½ »»ÈÈ oo


5. Wiring Diagram

NOTE

The code number of cable (Lead-connector) can be changed, see “Exploded Views and Parts List”.

43" Cable (Lead-connector)

Use(1)

POWER 12 Pin

(7)

LVDS FFC 51 Pin

Code BN39-01285K BN96-13325G

Photo

51" Cable (Lead-connector)

Use(1)

POWER 12 Pin

(7)

LVDS FFC 51 Pin

Code BN39-01285L BN96-13325F

Photo


5. Wiring Diagram

5.1.1. Pin Connection

(1)

CN801 (SMPS) ↔ CN201 (Main Board)

Pin No. (SMPS) Signal (SMPS) Pin No. (Main Board) Signal (Main Board)

1 PS-ON 1 SW_POWER

2 STBY 2 A5V_PW

3 GND 3 DGND

4 D15V 4 B15VS_PW

5 GND 5 DGND

6 GND 6 DGND

7 D5.3V 7 B5V_PW

8 D5.3V 8 B5V_PW

9 GND 9 DGND

10 D15V 10 B15V_PW

11 D15V 11 B15V_PW

12 D5.3V 12 B5V_PW

(2)

CN804 (SMPS) ↔ CN5000 (Y Board)

Pin No. (SMPS) Signal (SMPS) Pin No. (Y Board) Signal (Y Board)

1 208V 1 Vs

2 208V 2 Vs

3 GND 3 GND

4 D15V 4 Vg(15V)

5 GND 5 GND

6 VA 6 Va

(3)

43" only : CN802 (SMPS) ↔ CN2001 (Logic Board)

51" only : CN802 (SMPS) ↔ CN2002 (Logic Board)

Pin No. (SMPS) Signal (SMPS) Pin No. (Logic Board) Signal (Logic Board)

1 D5.3V 1 5.3V

2 D5.3V 2 5.3V

3 GND 3 GND

4 VS-SIGNAL 4 GND

5 PS-ON 5 PS_ON

6 VS-ON 6 VS_ON


5. Wiring Diagram

(4)

CN603D_3D (Main Board) ↔ BLUETOOTH

Pin No. (Main Board) Signal (Main Board) Pin No. (BLUETOOTH) Signal (BLUETOOTH)

1 FRAME_SYNC_IN 1 Reset_Module

2 FRAME_SYNC_OUT 2 VCC 5V

3 DGND 3 USB D-(BT)

4 USB_BT_DP 4 USB D+(BT)

5 USB_BT_DM 5 GND

6 A5V_PM 6 3D Sync Out

7 FUNC_INTR 7 3D Sync In

8 POWER_DET 8

(5)

CN1201 (Main Board) ↔ CN1 (FUNCTION)

Pin No. (Main Board) Signal (Main Board) Pin No. (FUNCTION) Signal (FUNCTION)

1 IR 1 IR

2 FUNC_GND 2 GND

3 FUNC_A3.3V 3 A3.3V

4 MSCT 4 SCL

5 MSDA 5 SDA

6 FUNC_INTR 6 INT

7 LED_STR 7 LED

(6)

CN302 (Main Board) ↔ SPEAKER

Pin No. (Main Board) Signal (Main Board)

1 R+_OUT

2 R-_OUT

3 L+_OUT

4 L-_OUT


5. Wiring Diagram

43” (7)

CN2023 (Logic Board) ↔ CN1602_HD (Main Board) 2D Only

Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal

1 GND 14 RIGHT(4)+ 27 RIGHT(0)- 40 GND

2 UART Tx 15 RIGHT(4)- 28 GND 41 GND

3 GND 16 RIGHT(3)+ 29 GND 42 GND

4 SDA 17 RIGHT(3)- 30 GND 43 GND

5 GND 18 GND 31 GND 44 GND

6 SCL 19 RightCLK+ 32 GND 45 GND

7 GND 20 RightCLK- 33 GND 46 GND

8 UART Rx 21 GND 34 GND 47 GND


10 GND 23 RIGHT(2)- 36 GND 49 3D_SYNC


12 N/C 25 RIGHT(1)- 38 GND 51 PDP_GO

13 GND 26 RIGHT(0)+ 39 GND

51” (7)

CN2023 (Logic Board) ↔ CN1602_HD (Main Board) 2D Only

Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal

1 GND 14 RIGHT(4)+ 27 RIGHT(0)- 40 LEFT(1)-

2 UART Tx 15 RIGHT(4)- 28 GND 41 LEFT(0)+

3 GND 16 RIGHT(3)+ 29 LEFT(4)+ 42 LEFT(0)-

4 SDA 17 RIGHT(3)- 30 LEFT(4)- 43 GND

5 GND 18 GND 31 LEFT(3)+ 44 GND

6 SCL 19 RightCLK+ 32 LEFT(3)- 45 GND

7 GND 20 RightCLK- 33 GND 46 GND

8 UART Rx 21 GND 34 LEFTCLK+ 47 GND

9 GND 22 RIGHT(2)+ 35 LEFTCLK- 48 GND

10 GND 23 RIGHT(2)- 36 GND 49 3D_SYNC

11 GND 24 RIGHT(1)+ 37 LEFT(2)+ 50 GND

12 N/C 25 RIGHT(1)- 38 LEFT(2)- 51 PDP_GO

13 GND 26 RIGHT(0)+ 39 LEFT(1)+


Exploded Views and Parts List

1. PS43D450A2WXZGExploded View

Copyright© 1995-2011 SAMSUNG. All rights reserved. 1


Parts List

No. Parent Lvl. Loc. Material Code Description & Specification SNA Qty.

1 BN90-03179L 2 F001A BN96-17869L ASSY COVER P-FRONT; PD45043,PC,V2,CHARCO

SA 1

1-1 BN96-17869L 3 F001 BN63-07770L COVER-FRONT; PD450/49043,PC,V2,CHARCOAL

SNA 1

1-2 BN96-17869L 3 FB21A BN96-16729D ASSY BOARD P-TOUCH FUNCTION& IR; PN43D490,

SA 1

2 BN91-08419Q 2 U001A BN96-18206A ASSY PDP MODULE P;S42AX-YD15,PP42AF085A,

SC 1

3 BN90-03179L 2 SP01A BN96-18071B ASSY SPEAKER P; 6ohm,4pin,10W,PDPnormal

SA 1

4 BN91-05862N 2 BN61-07042A BRACKET-MODULE;42PD490,SECC,T1.2

SNA 2

5 BN91-05862N 2 BN63-07777A COVER-AV;42PD490(EO),ABS,HB,BLK(BK500)

SNA 1

6 BN91-08419Q 2 M0014 BN94-04349J ASSY PCB MISC-MAIN; PD450 SA 1

7 BN91-05862N 2 CB25A BN96-16790A ASSY BRACKET P-WALL;PD450/490,SECC,T0.2

SA 4

8 BN91-05862N 2 SB05A BN96-16791B ASSY BRACKET P-STAND LINK;PD450/490 43,S

SA 1

9 BN96-17865D 3 RB01 BN63-07786C COVER-BOTTOM; PD550 50",NHHIPS,V1,BLK

SNA 1

10 BN90-03192F 2 R001A BN96-16782B ASSY COVER P-REAR; PD45043,EUROPE

SA 1

11 BN90-03302C 2 SG03A BN96-16786C ASSY GUIDE P-STAND; PD450/49043,PC G/F 2

SA 1

12 BN90-03302C 2 SB04A BN96-16789B ASSY STAND P-BASE; PD45043,PC+ABS V0,(BK

SA 1

2 Copyright© 1995-2011 SAMSUNG. All rights reserved.


2. Electrical Parts ListLevel Loc. Part Code Description & Specification Qty. SA/SNA

PS43D450A2WXZG (E110)

1 BN90-03179L ASSY COVER FRONT;PD450/490 43 1 SNA

.2 F001A BN96-17869L ASSY COVER P-FRONT;PD450 43,PC,V2,CHARCO 1 SA

..3 BN60-00288A SPACER-SCREEN;43PD490,SPONGE,550,T1.5,5, 2 SNA

..3 BN60-00288E SPACER-SCREEN;43PD490,SPONGE,960,T1.5,5, 2 SNA

..3 AB326 BN61-04661A BRACKET-STOPPER;L650,SK-5,T0.4,Plating,H 2 SNA

..3 BN61-04692A BOSS-PRIMER;#94,clear,35cps 1 SNA

..3 BN61-04731F BOSS-TAPE;AMBER,ACRYL,T1.1,W6.0mm,WHITE, 1 SNA

..3 BN61-07049A HOLDER-BOSS BOTTOM;42PD490,ABS HB,Black 1 SNA

..3 CCM1 BN63-05199P COVER-SHEET;AMBER,PE,T0.08,W1000,200M,CL 1 SNA

..3 F001 BN63-07770L COVER-FRONT;PD450/490 43,PC,V2,CHARCOAL 1 SNA

...4 0103-007268 RESIN-PC;TN-1045M,70784,TP0010,0.8, 3.0 618 SNA

..3 BN81-02422A A/S-ADHESIVE;TECNOMELT,Q9268H,WHT 0 SNA

..3 FB21A BN96-16729D ASSY BOARD P-TOUCH FUNCTION & IR;PN43D490, 1 SA

.2 SP01A BN96-18071B ASSY SPEAKER P;6ohm,4pin,10W,PDP normal 1 SA

1 R001A BN90-03192F ASSY COVER REAR;PD450/490 43 1 SNA

.2 R001A BN96-16782B ASSY COVER P-REAR;PD450 43,EUROPE 1 SA

..3 BN61-07307A HOLDER-WIRE;PD490,PP,HB, BLK 1 SNA

..3 BN63-04499A FELT;P450 42,FELT,0.5,15,360,NTR 2 SNA

..3 R001 BN63-07801B COVER-REAR;PD490 43,PCM,TO.45,BKN-P824 1 SNA

..3 BN64-01582A INLAY-AV;42PD490,PS SHEET,T0.5,EUROPE 1 SNA

..3 T0071 BN64-01585A INLAY-TERMINAL;42PD490,PS SHEET,T0.5,EUR 1 SNA

..3 T0139 BN65-00003A CLAMPER BAG;42C7,LDPE,HB,BLK 1 SNA

1 S001A BN90-03302C ASSY STAND;PD490 1 SNA

.2 SG03A BN96-16786C ASSY GUIDE P-STAND;PD450/490 43,PC G/F 2 1 SA

..3 T0524 6902-001063 BAG PE;LDPE,T0.05,W180,L350,TRP,RECYCLE 1 SNA

..3 SG03 BN61-07058A GUIDE-STAND;42PD490,PC,G/F 20% 1 SNA

..3 BN68-03503C MANUAL FLYER-05,STAND GUIDE;P550(43~64), 1 SNA

..3 BN96-18013E ASSY ACCESSORY-SCREW;6003-001782,4EA,ALL 1 SNA

...4 SCREW 6003-001782 SCREW-TAPTYPE;BH,+,B,M4,L12,ZPC(BLK),SWR 4 SA

..3 BN96-18013Q ASSY ACCESSORY-SCREW;6003-001807,4EA,ZPC 1 SNA

...4 SCREW 6003-001807 SCREW-TAPTYPE;BH,S,M4,L10,ZPC(BLK),SWRCH 4 SA

...4 T0524 6902-000341 BAG PE;LDPE,T0.05,L90,W70,TRP,,,PE MARK 1 SNA

.2 SB04A BN96-16789B ASSY STAND P-BASE;PD450 43,PC+ABS V0,(BK 1 SA

..3 M0081 6003-001239 SCREW-TAPTYPE;FH,+,B,M4,L10,ZPC(WHT),SWR 13 SA

..3 T0524 6902-000518 BAG PE;HDPE/NITRON/HDPE,T0.015/T0.05(DOU 1 SNA

..3 AB323 BN61-07043A BRACKET-STAND;42PD490,SECC,T2.0 1 SNA

..3 SG01 BN61-07060A GUIDE-STAND NECK;42PD490,PC,G/F 20% 1 SNA



Level Loc. Part Code Description & Specification Qty. SA/SNA

..3 CCM1 BN63-02183D COVER-SHEET;Rhcm,PE Vinyl,T0.05,680mm,20 1 SNA

..3 BN63-04755G COVER-SHEET;42PC450,PE,T0.05,W250mm,200M 1 SNA

..3 SC05 BN63-07802B COVER-STAND;42PD490,PC+ABS,V0,BK0008,GF 1 SNA

...4 0103-005041 RESIN-PC;FR3200TV,901408,BK0008,1.2mm V- 704 SNA

..3 BN68-03518C LABEL-STICKER;WW,ALL,85,30,stand sticker 1 SNA

..3 M0019 BN73-00052C RUBBER-FOOT;LCD TV,CR RUBBER,T2.0 DIA19, 6 SNA

1 BN91-05862N ASSY SHIELD;PD450/490 43 1 SNA

.2 6001-002670 SCREW-MACHINE;BH,+,M3,L6,Ni PLT,SWRCH18A 4 SNA

.2 M0081 6003-000337 SCREW-TAPTYPE;BH,+,S,M4,L10,ZPC(BLK),SWR 7 SA

.2 M0081 6003-001439 SCREW-TAPTYPE;BH,+,S,M4,L8,ZPC(WHT),SWRC 1 SA

.2 SCREW 6003-001782 SCREW-TAPTYPE;BH,+,B,M4,L12,ZPC(BLK),SWR 5 SA

.2 BN61-07042A BRACKET-MODULE;42PD490,SECC,T1.2 2 SNA

.2 BN63-07777A COVER-AV;42PD490(EO),ABS,HB,BLK(BK500) 1 SNA

..3 0103-004609 RESIN-ABS;HF-0680U,K21294,BK0007,1.5mm H 14 SNA

.2 CB25A BN96-16790A ASSY BRACKET P-WALL;PD450/490,SECC,T0.2 4 SA

..3 CB20 BN61-07044A BRACKET-WALL;42PC490,SECC,T1.6 4 SNA

..3 BN61-07441A HOLDER-CAP;PDP NORMAL,ABS HB,BLK (BK0020 4 SNA

.2 SB05A BN96-16791B ASSY BRACKET P-STAND LINK;PD450/490 43,S 1 SA

..3 BN61-02429P STUD-PEM;PNB,M3.8,D8,L11,ZPC(SIL),SUM24L 6 SNA

..3 CB18 BN61-07045A BRACKET-STAND LINK;42PD490,SECC,T1.6 1 SNA

..3 CD101 BN65-00005A CLAMP-WIRE;55UD6500,NYLON 66,BLK 3 SNA

.2 B001A BN96-17865D ASSY COVER P-BOTTOM;PD450 43/51,HIPS,V1, 1 SNA

..3 BN60-00033B SPACER-FELT;PD450,FELT,L30mm,BLK,T0.35mm 1 SNA

..3 RB01 BN63-07786C COVER-BOTTOM;PD550 50",NH HIPS,V1,BLK 1 SNA

...4 0103-007489 RESIN-HIPS;NH-1917,K2901,BK0020,2.5 V-1 80 SNA

1 BN91-08419Q ASSY PDP;PD450 1 SNA

.2 EC13 BN39-01285K LEAD CONNECTOR;PN43D450,Flat Connector A 1 SA

.2 BN81-06605A A/S-TAPE-FILAMENT;ELMATIT,T0.1,W20,L5000 0 SNA

.2 M0014 BN94-04349J ASSY PCB MISC-MAIN;PD450 1 SA

..3 0202-001608 SOLDER-WIRE FLUX;LFC7-107,D0.8,99.3Sn/0. 0 SNA

..3 BN97-05191H ASSY SMD;PD450,BN41-01761A 1 SNA

...4 0202-001477 SOLDER-CREAM;LST309-M,D20~45um,96.5Sn/3A 3 SNA

...4 DS01A 0401-001056 DIODE-SWITCHING;MMBD4148SE,100V,200mA,SO 3 SA

...4 0403-001180 DIODE-ZENER;BZX84C6V2,5.8-6.6V,350mW,SOT 1 SA

...4 0403-001783 DIODE-ZENER;BZB84-C6V2,5.8/6.6V,300mW,SO 4 SNA

...4 D0254 0404-001404 DIODE-SCHOTTKY;BAT721C,40V,200mA,SOT-23, 1 SA

...4 T0139 0406-001200 DIODE-TVS;RCLAMP0504F,6/-/-V,150W,SC-70 1 SA

...4 SD3 0407-000114 DIODE-SWITCHING;KDS184,80V,100mA,SOT-23, 1 SNA

...4 KQ1 0501-000279 TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOT- 1 SA

...4 Q101 0501-000445 TR-SMALL SIGNAL;KTC3875S-Y,NPN,150mW,SOT 6 SC




...4 CEQ2 0505-000110 FET-SILICON;2N7002,N,60V,115mA,7.5ohm,0. 2 SA

...4 IC104 0801-002630 IC-CMOS LOGIC;74AHCT1G08,2-INPUT AND GAT 1 SA

...4 ND51C20801-002780 IC-CMOS LOGIC;74LVC1G17,SCHMITT-TRIGGER 1 SA

...4 IC104 0801-003330 IC-CMOS LOGIC;Octal buffer,DQFN,20P,4.5x 2 SA

...4 IC104 0802-001012 IC-CMOS LOGIC;74LCX245,TRANSCEIVER,DQFN, 1 SNA

...4 IC112 1103-001310 IC-EEPROM;24LC02B,256X8BIT,SOIC,8P,3.91X 4 SA

...4 1103-001487 IC-EEPROM;AT24C256C-SSHL-T,256Kbit,32Kx8 1 SA

...4 1105-002194 IC-DDR3 SDRAM;K4B1G1646G-BCH9,DDR3 SDRAM 2 SA

...4 1107-002076 IC-NOR FLASH;W25Q40BVSSIP,4Mbit,SOP,8P,5 1 SNA

...4 1201-003153 IC-POWER AMP;NTP-7411S,MLF,48P,7x7mm,DUA 1 SA

...4 1201-003183 IC-AUDIO AMP;DRV612,HTSSOP,14P,5x4.4mm,D 1 SA

...4 T0087 1203-002519 IC-POSI.FIXED REG.;KIA7809AF,DPAK,3P,240 1 SA

...4 T0087 1203-002835 IC-POSI.FIXED REG.;7805,3P,6.6x6.1mm,PLA 1 SA

...4 T0087 1203-002898 IC-POSI.FIXED REG.;G950T45R,T0-252,3P,6. 1 SA

...4 1203-004364 IC-VOL. DETECTOR;RT9818C-42PV,SOT-23,3P, 1 SA

...4 1203-006017 IC-VOL. DETECTOR;RT9824GJ8,TSOT23,8P,2.9 1 SA

...4 T0087 1203-006136 IC-POSI.FIXED REG.;AP1117D-18-GZ-13-89,T 1 SA

...4 IC012 1203-006138 IC-POSI.ADJUST REG.;AP1117DGZ-13-89,TO-2 1 SA

...4 1203-006142 IC-DC/DC CONVERTER;BD8924G,5P,2.9x1.6x1. 1 SA

...4 1203-006337 IC-POSI.FIXED REG.;G9091-330T11U,SOT-23- 1 SA

...4 1203-006619 IC-DC/DC CONVERTER;AOZ1033AI,SO-8,8P,4.9 1 SA

...4 1203-006684 IC-DC/DC CONVERTER;TPS54327DDAR,HSOP8,8P 1 SNA

...4 1204-003313 IC-DECODER;SEMS23,LFBGA,568P,20.2x20.2mm 1 SA

...4 1205-003201 IC-BUS SWITCH;TC7WB125FK,SSOP,8P,2x2.3mm 1 SA

...4 1205-003479 IC-SWITCH;TPS2051BDBVR,SOT-23,5P,2.9x1.6 1 SA

...4 1205-003733 IC-SWITCH;AP2191MPG-13,MSOP-8L-EP,8P,2.9 1 SA

...4 1405-001271 VARISTOR;20Vdc,5A,1.0x0.5x0.6mm,TP,100V, 5 SA

...4 MR604 2007-000137 R-CHIP;2Kohm,5%,1/16W,TP,1005 10 SNA

...4 R105 2007-000138 R-CHIP;100ohm,5%,1/16W,TP,1005 30 SA

...4 AR49 2007-000140 R-CHIP;1Kohm,5%,1/16W,TP,1005 9 SNA

...4 MR306 2007-000141 R-CHIP;2.2Kohm,5%,1/16W,TP,1005 2 SNA

...4 AVR73 2007-000142 R-CHIP;2.7Kohm,5%,1/16W,TP,1005 1 SA

...4 R319 2007-000143 R-CHIP;4.7Kohm,5%,1/16W,TP,1005 31 SNA

...4 R104 2007-000148 R-CHIP;10Kohm,5%,1/16W,TP,1005 36 SA


...4 RZ07 2007-000156 R-CHIP;30Kohm,5%,1/16W,TP,1005 1 SA


...4 2007-000160 R-CHIP;68Kohm,5%,1/16W,TP,1005 2 SA

...4 DR39 2007-000162 R-CHIP;100Kohm,5%,1/16W,TP,1005 6 SNA

...4 R509 2007-000170 R-CHIP;1Mohm,5%,1/16W,TP,1005 1 SNA




...4 R111 2007-000171 R-CHIP;0ohm,5%,1/16W,TP,1005 3 SNA

...4 HDR17 2007-000172 R-CHIP;10ohm,5%,1/16W,TP,1005 2 SNA


...4 UR23 2007-000174 R-CHIP;47ohm,5%,1/16W,TP,1005 2 SNA


...4 R726 2007-000695 R-CHIP;3.3ohm,5%,1/10W,TP,1608 4 SNA

...4 R124 2007-000775 R-CHIP;33Kohm,5%,1/16W,TP,1005 2 SNA


...4 S1G08432007-001125 R-CHIP;68Kohm,1%,1/10W,TP,1608 1 SA

...4 2007-001168 R-CHIP;75ohm,5%,1/4W,TP,3216 2 SA

...4 OTR1 2007-001292 R-CHIP;33ohm,5%,1/16W,TP,1005 17 SNA

...4 DR43 2007-001298 R-CHIP;51ohm,5%,1/16W,TP,1005 2 SNA

...4 DR1 2007-001301 R-CHIP;68ohm,5%,1/16W,TP,1005 10 SA



...4 2007-001333 R-CHIP;18Kohm,5%,1/16W,TP,1005 7 SNA

...4 PR24 2007-002970 R-CHIP;56ohm,5%,1/16W,TP,1005 4 SA

...4 HDR8 2007-007095 R-CHIP;390ohm,5%,1/16W,TP,1005 1 SA

...4 2007-007138 R-CHIP;27Kohm,1%,1/16W,TP,1005 1 SA


...4 2007-007156 R-CHIP;1ohm,5%,1/16W,TP,1005 21 SNA

...4 2007-007311 R-CHIP;22Kohm,1%,1/16W,TP,1005 1 SA



...4 2007-007463 R-CHIP;1.1Kohm,1%,1/16W,TP,1005 1 SA

...4 2007-007517 R-CHIP;240ohm,1%,1/16W,TP,1005 2 SNA

...4 2007-007698 R-CHIP;5.1Kohm,1%,1/16W,TP,1005 2 SNA

...4 MR11 2007-008015 R-CHIP;75ohm,1%,1/16W,TP,1005 11 SA


...4 2007-008298 R-CHIP;49.9ohm,1%,1/16W,TP,1005 4 SA

...4 2007-008649 R-CHIP;220ohm,1%,1/16W,TP,1005 1 SNA

...4 ZRN10 2011-001261 R-NETWORK;33ohm,5%,1/16W,L,CHIP,8P,TP,2. 6 SA

...4 DAR09 2011-001262 R-NETWORK;22ohm,5%,1/16W,L,CHIP,8P,TP,2. 7 SA

...4 2011-001264 R-NETWORK;10ohm,5%,1/16W,L,CHIP,8P,TP,2. 10 SNA

...4 HRP2 2011-001344 R-NETWORK;100ohm,5%,1/16W,L,CHIP,8P,TP,2 2 SA

...4 DRP29 2011-001396 R-NETWORK;4.7Kohm,5%,1/16W,L,CHIP,8P,TP, 2 SA

...4 2011-001449 R-NETWORK;22ohm,5%,1/16W,L,4P,TP,1010 4 SA

...4 2011-001519 R-NETWORK;33OHM,5%,1/16W,L,CHIP,4P,TP,1. 2 SA

...4 2011-001587 R-NETWORK;100ohm,5%,1/16W,L,CHIP-V,4P,TP 1 SNA

...4 2011-001589 R-NETWORK;0ohm,5%,1/16W,L,CHIP-V,4P,TP,1 6 SNA




...4 PC43 2203-000233 C-CER,CHIP;0.1nF,5%,50V,C0G,TP,1005 7 SA

...4 DC2 2203-000330 C-CER,CHIP;0.012nF,5%,50V,C0G,TP,1005 2 SA

...4 MC9 2203-000359 C-CER,CHIP;0.15nF,5%,50V,C0G,TP,1005,0.5 1 SA

...4 C254 2203-000438 C-CER,CHIP;1nF,10%,50V,X7R,TP,1005 11 SA

...4 C507 2203-000489 C-CER,CHIP;2.2nF,10%,50V,X7R,TP,1005 5 SA

...4 AD480 2203-000530 C-CER,CHIP;2.7nF,10%,50V,X7R,TP,1005,- 1 SNA

...4 V1233 2203-000575 C-CER,CHIP;220nF,10%,25V,X7R,TP,2012 2 SNA

...4 AD480 2203-000679 C-CER,CHIP;0.027nF,5%,50V,C0G,TP,1005 2 SNA

...4 AD480 2203-000714 C-CER,CHIP;3.3nF,10%,50V,X7R,TP,1005,- 6 SA


...4 AD480 2203-000995 C-CER,CHIP;0.047nF,5%,50V,C0G,TP,1005 2 SA

...4 AD480 2203-001412 C-CER,CHIP;0.03nF,5%,50V,NP0,TP,1005 6 SNA

...4 AD480 2203-001428 C-CER,CHIP;470nF,10%,50V,X7R,TP,2012 2 SNA


...4 AD480 2203-002525 C-CER,CHIP;0.56nF,10%,50V,X7R,TP,1005 6 SNA

...4 AAC1 2203-005249 C-CER,CHIP;100nF,10%,50V,X7R,TP,1608 13 SNA

...4 AD480 2203-005344 C-CER,CHIP;22nF,10%,25V,X7R,TP,1005,0.5T 1 SNA

...4 AD480 2203-005393 C-CER,CHIP;0.005nF,0.1pF,50V,NP0,TP,1005 1 SNA

...4 VC37 2203-006048 C-CER,CHIP;100nF,10%,10V,X7R,TP,1005 108 SA


...4 JC10 2203-006324 C-CER,CHIP;2200nF,10%,10V,X5R,1608 8 SA

...4 C802 2203-006348 C-CER,CHIP;1000nF,10%,25V,X5R,TP,1608,0. 1 SA

...4 C125 2203-006361 C-CER,CHIP;10000nF,10%,10V,X5R,TP,2012 2 SC

...4 HE4 2203-006474 C-CER,CHIP;22000nF,20%,6.3V,X5R,2012 12 SA

...4 HDC11 2203-006562 C-CER,CHIP;1000nF,10%,10V,X5R,TP,1005 14 SNA

...4 AD480 2203-006824 C-CER,CHIP;4700nF,10%,10V,X5R,1608 2 SNA

...4 C23 2203-006890 C-CER,CHIP;10000nF,20%,6.3V,X5R,TP,1608 29 SA


...4 AD480 2203-007176 C-CER,CHIP;10000nF,10%,16V,X5R,TP,2012,1 16 SNA

...4 T0052 2703-000158 INDUCTOR-SMD;1uH,10%,2012 4 SA

...4 T0052 2703-003149 INDUCTOR-SMD;2.2uH,20%,5050 1 SA

...4 2703-003407 INDUCTOR-SMD;120nH,5%,1608 1 SA


...4 2703-003890 INDUCTOR-SMD;47uH,10%,3225 1 SC

...4 2704-000029 INDUCTOR-SMD-ARRAY;5.6uH,2300mA,2,0.08oh 2 SNA

...4 X202 2801-003326 CRYSTAL-SMD;24MHz,30ppm,28-ABX,20pF,50oh 1 SA

...4 X202 2801-003948 CRYSTAL-SMD;12MHz,30ppm,28-AAN,12pF,60oh 1 SA

...4 F103 2901-001506 FILTER-EMI SMD;5V,0.13A,0pF,2x1x0.5mm,TP 2 SA

...4 DR32 3301-000314 BEAD-SMD;120ohm,1608,TP,120ohm/100MHz 7 SNA

...4 T0568 3301-001404 BEAD-SMD;30ohm,2012,TP,15.9OHM/30MHz,- 4 SA




...4 T0568 3301-002039 BEAD-SMD;26ohm,1608,TP 34 SA

...4 3701-001591 CONNECTOR-HDMI;19P,2ROW,FEMALE,SMD-S,AU 2 SC

...4 3701-001746 CONNECTOR-DSUB;15P,3ROW,FEMALE,STARAIGHT 1 SA

...4 3707-001106 CONNECTOR-OPTICAL;STRAIGHT W/L,SPDIF 1 SA

...4 3708-002930 CONNECTOR-FPC/FFC/PIC;51P,0.5mm,SMD-A,AU 1 SA

...4 3709-001640 CONNECTOR-CARD SLOT;68P(U/S) W/L,1.27mm, 1 SC

...4 3711-007585 CONNECTOR-HEADER;BOX,4P,1R,2.5mm,ANGLE-D 1 SA

...4 EH01 3711-007769 HEADER-BOARD TO CABLE;BOX,12P,1R,2.00mm, 1 SA

...4 EH01 3711-007775 HEADER-BOARD TO CABLE;BOX,7P,1R,1.25mm,S 1 SA

...4 3722-003225 JACK-USB;4P/1C,Au,BLK,SMD-A(DIP),A 1 SA

...4 3722-003226 JACK-PHONE;7P/1C,SN,BLK 2 SA

...4 3722-003247 JACK-PIN;5P+Shield W/L,NI,GN/BL/RD/WH/RD 1 SA

...4 3722-003252 JACK-SCART;21P,Sn,BLK 1 SA

...4 ET01 BN40-00197A TUNER;DTOS40FVL082A,DTOS40FVL082A,DVB-T/ 1 SA

...4 BN41-01761A PCB MAIN;PDP D450/D490/D550 EU,FR-4,4,1. 1 SNA

...4 BN97-06189E ASSY MICOM;PX9DVBEU4A-1000,BN46-00166E,B 1 SNA

....5 1107-002049 IC-NAND FLASH;K9F1G08U0D-SCB0,1Gbit,128M 1 SA

....5 BN46-00153A S/W MICOM;T-MSV4DEUC-XXXX,EU/AU/SH/MV/AB 1 SNA

....5 BN46-00166E S/W-E-MANUAL;PDP X9 EU4,XC XN ZF ZG ZT T 1 SNA

...4 BN97-06217A ASSY MICOM;U57A,U56A,2011.06.16,X9_SUB M 1 SNA

....5 0903-001718 IC-MICROCONTROLLER;61P805-RG480WT,LQFP,4 1 SNA

..3 BN97-06150A ASSY DRM-KEY CODE-ASS`Y;COM_012,TV,-,Eur 1 SNA

...4 BN46-00110G KEY CODE-CERTIFI;HDCP,TV,MSTAR,General 1 SNA

...4 BN46-00115A KEY CODE-CERTIFI;CI+,TV,MSTAR,Euro 1 SNA

..3 T0066 BP62-00017A HEAT SINK-ES;SP-50L2HX,A6063S,T2.0,26.2, 1 SNA

.2 FL06 BN96-13325G ASSY CABLE P;PS42D450,FFC CABLE,175mm,51 1 SA

.2 U001A BN96-18206A ASSY PDP MODULE P;S42AX-YD15,PP42AF085A, 1 SC

..3 P001A BN44-00442B DC VSS-PDP;PB4,AC/DC,AC100~240V,50/60Hz, 1 SC

..3 UL01A BN96-16507A ASSY PDP P-LOGIC BOARD;S42AX-YB11,PL42AF 1 SA

..3 UE01A BN96-16508A ASSY PDP P-E-BUFFER BOARD;S42AX-YB11,PL4 1 SA

..3 UF01A BN96-16509A ASSY PDP P-F-BUFFER BOARD;S42AX-YB11,PL4 1 SA

..3 UX03A BN96-16510A ASSY PDP P-X-MAIN BOARD;S42AX-YB11,PL42A 1 SA

..3 UY04A BN96-16511A ASSY PDP P-Y-MAIN BOARD;S42AX-YB11,PL42A 1 SA

..3 UY01A BN96-16512A ASSY PDP P-Y-SCAN BUFFER BOARD;S42AX-YB1 1 SA

1 BN92-07574F ASSY BOX;PD450/490 43 1 SNA

.2 BH68-00662A LABEL BOX-00;ALL MODEL,MOJO 90G,60,110,W 1 SNA

.2 BN69-06093A BOX-SET,IN;43PD490(270mm),CB,C-01,DW1, Y 1 SNA

.2 BN69-06326H BOX-SET;43PD450(270mm),CB,C-03,DW3, YEL, 1 SNA

1 BN92-07875A ASSY P/MATERIAL;PS43D450A2XXV 1 SNA

.2 T0214 0203-001102 TAPE-OPP MASKING;OPP-2,T0.05,W100,L400M, 1 SNA




.2 T0214 0203-004955 TAPE-OPP MASKING;T0.06mm(60uM),W75mm,TRP 1 SNA

.2 6902-001180 BAG ROLL;HDPE/HDPE/NITRON,T0.5,W1100,L17 3 SNA

.2 M040 6922-000013 BAND PP;PP,W18,L2300/L2900,TRP 1 SNA

.2 T0214 AA61-20285C HOLDER-BOX;CORAL,PP,BLACK,HB,17.5g 4 SNA

..3 0103-004631 RESIN-HIPS;HF-1690H,K21294,BK0007,1.5mm 84 SNA

.2 BH69-40383M PACKING INNER-00,PAD;COMM,CB,1000,800,YE 1 SNA

.2 BN63-07496A COVER-PALLET FOIL;LB530,PE,T0.05,2000,20 1 SNA

.2 BN63-07517X COVER-SHEET NITRON;LS24EFHKU/EN,PE,T3.0, 1 SNA

.2 BN68-02422B LABEL-WARNING SHIPPING;ALL MODEL,A/P 100 1 SNA

.2 BN69-03934A WRAP STRETCH FILM;All,HDPE,0.012,500,300 8 SNA

.2 BN69-04029A PAD EPS-EDGE;CB,B800,W50x50,L2200,YEL,66 1 SNA

.2 BN69-05694A CUSHION-SET;42PD490,EPS,16.7 g/l ,abroad 1 SNA

.2 BN69-06338A PALLET-WOODEN;PS43D450,WOOD-OTH,1120,108 1 SNA

.2 BN81-02321A BAG-AIR;LIGHT FLEX PLASTIK,PE WHITE,L120 1 SNA

1 ACCE1 BN92-07889A ASSY ACCESSORY;PN43D490A1XZS 1 SNA

.2 BN68-03866A LABEL-STICKER;PD4A,PET,T0.05,60,120,Ener 1 SNA

.2 ACCE2 BN96-17007Y ASSY ACCESSORY-CABLE;PL51D490A1MXZL 1 SNA

..3 T0121 3301-002049 CORE-FERRITE;33.6X30.5,3500 2 SA

..3 T0268 3903-000456 CBF-POWER CORD;DT,EU/KR,CP3,IEC320 C13-R 1 SC

..3 T0685 4301-000103 BATTERY-ALKALINE;1.5V,750mAH,LR03,10.5x4 2 SNA

..3 REMO2 AA59-00484A REMOCON;TM950,48,3V,EUROPE_iDTV,580,570, 1 SA

..3 M9889 BN63-01798B CLOTH-CLEAN;CLOTH,180,200,sea blue,ToC 1 SNA

.2 ACCE4 BN96-17030A ASSY ACCESSORY-MANUAL;PS51D390* 1 SNA

..3 T0524 6902-000110 BAG PE;LDPE,T0.05,W250,L400,TRP,28,2,9.2 1 SNA

..3 T0527 BN68-00513A LABEL-E,PASS;ALL MODEL,YUPO(110G),50X15, 1 SNA

..3 BN68-00514K MANUAL FLYER-WARRANTY CARD;comm,Samsung, 1 SNA

..3 BN68-03019A LEAFLET-SAFETY GUIDE;ALL,SAMSUNG,28LENGS 1 SNA

..3 BN68-03491C MANUAL USERS;PD450,SAMSUNG,Eng/Ger/Fre/I 1 SNA

1 BN92-08246C ASSY LABEL;550 1 SNA

.2 T0527 AA68-03752B LABEL-STICKER;WW,ALL,Art Paper(90g),25,3 1 SNA

.2 T0527 BP68-00052B LABEL-00,RATING;CCTV,TETRON PAPER,T0.05, 1 SNA



Parts List



SA 1


SNA 1


SA 1

2 BN91-08419R 2 U001A BN96-18206B ASSY PDP MODULE P;S42AX-YD15,PP42AF087B,

SA 1


SA 1


SNA 2


SNA 1

6 BN91-08419R 2 M0014 BN94-04349J ASSY PCB MISC-MAIN; PD450 SA 1


SA 4


SA 1


SNA 1


SA 1


SA 1


SA 1




PS43D450A2WXZG (E212)


































































1 BN91-08419R ASSY PDP;PD450 1 SNA



.2 M0014 BN94-04349J ASSY PCB MISC-MAIN;PD450 1 SA


..3 BN97-05191H ASSY SMD;PD450,BN41-01761A 1 SNA





















...4 1107-002076 IC-NOR FLASH;W25Q40BVSSIP,4Mbit,SOP,8P,5 1 SNA














...4 1204-003313 IC-DECODER;SEMS23,LFBGA,568P,20.2x20.2mm 1 SA




...4 1405-001271 VARISTOR;20Vdc,5A,1.0x0.5x0.6mm,TP,100V, 5 SA


...4 R105 2007-000138 R-CHIP;100ohm,5%,1/16W,TP,1005 30 SA







...4 RZ07 2007-000156 R-CHIP;30Kohm,5%,1/16W,TP,1005 1 SA


...4 2007-000160 R-CHIP;68Kohm,5%,1/16W,TP,1005 2 SA















...4 2007-001168 R-CHIP;75ohm,5%,1/4W,TP,3216 2 SA









...4 2007-007138 R-CHIP;27Kohm,1%,1/16W,TP,1005 1 SA


...4 2007-007156 R-CHIP;1ohm,5%,1/16W,TP,1005 21 SNA

...4 2007-007311 R-CHIP;22Kohm,1%,1/16W,TP,1005 1 SA



...4 2007-007463 R-CHIP;1.1Kohm,1%,1/16W,TP,1005 1 SA

...4 2007-007517 R-CHIP;240ohm,1%,1/16W,TP,1005 2 SNA




...4 2007-008298 R-CHIP;49.9ohm,1%,1/16W,TP,1005 4 SA

...4 2007-008649 R-CHIP;220ohm,1%,1/16W,TP,1005 1 SNA





















...4 AD480 2203-000714 C-CER,CHIP;3.3nF,10%,50V,X7R,TP,1005 6 SA














...4 C125 2203-006361 C-CER,CHIP;10000nF,10%,10V,X5R,TP,2012 2 SC

...4 HE4 2203-006474 C-CER,CHIP;22000nF,20%,6.3V,X5R,TP,2012 12 SA
















...4 T0568 3301-001404 BEAD-SMD;30ohm,2012,TP,15.9OHM/30MHz,- 4 SA

















...4 ET01 BN40-00197A TUNER;DTOS40FVL082A,DTOS40FVL082A,DVB-T/ 1 SA

...4 BN41-01761A PCB MAIN;PDP D450/D490/D550 EU,FR-4,4,1. 1 SNA

...4 BN97-06189E ASSY MICOM;PX9DVBEU4A-1000,BN46-00166E,B 1 SNA

....5 1107-002049 IC-NAND FLASH;K9F1G08U0D-SCB0,1Gbit,128M 1 SA

....5 BN46-00153A S/W MICOM;T-MSV4DEUC-XXXX,EU/AU/SH/MV/AB 1 SNA

....5 BN46-00166E S/W-E-MANUAL;PDP X9 EU4,XC XN ZF ZG ZT T 1 SNA

...4 BN97-06217A ASSY MICOM;U57A,U56A,2011.06.16,X9_SUB M 1 SNA







.2 U001A BN96-18206B ASSY PDP MODULE P;S42AX-YD15,PP42AF087B, 1 SA


..3 UL01A BN96-16507B ASSY PDP P-LOGIC MAIN BOARD;S42AX-YB11,L 1 SA



..3 UX03A BN96-16510B ASSY PDP P-X-MAIN BOARD;S42AX-YB11,LJ92- 1 SA



















.2 BN63-08890P COVER-SHEET NITRON;LS19CLYSB,PE,T2.0,114 1 SNA


























Parts List



SA 1


SNA 1


SA 1

2 BN91-07198X 2 U001A BN96-16470A ASSY PDP MODULE P;S42AX-YB11,PL42AF080A,

SA 1


SA 1

4 BN91-05862J 2 BN61-07042A BRACKET-MODULE;42PD490,SECC,T1.2

SNA 2

5 BN91-05862J 2 BN63-07777A COVER-AV;42PD490(EO),ABS,HB,BLK(BK500)

SNA 1

6 BN91-07198X 2 M0014 BN94-04884A ASSY PCB MISC-MAIN;PS43D450*,XC,XN,Z,ZG,

SA 1

7 BN91-05862J 2 CB25A BN96-16790A ASSY BRACKET P-WALL;PD450/490,SECC,T0.2

SNA 4

8 BN91-05862J 2 SB05A BN96-16791A ASSY BRACKET P-STAND LINK;PD450/490 43,S

SNA 1


SNA 1


SA 1

11 BN90-03302C 2 SG03A BN96-16786C ASSY STAND P-GUIDE; PD450/49043,PC G/F 2

SA 1


SA 1




PS43D450A2WXZG (I101)











...4 0103-007268 RESIN-PC;TP0010,2.0V0,NH PC,NH PC 2.0 V2 618 SNA

..3 BN68-03658A LABEL-01,LED POP;PDP,64/51,PET,T0.05,100 1 SNA






..3 BN63-04499A FELT;P450 42,FELT,0.5,15,360 2 SNA






.2 SG03A BN96-16786C ASSY STAND P-GUIDE;PD450/490 43,PC G/F 2 1 SA






..3 BN96-18013F ASSY ACCESSORY-SCREW;6001-002621,4EA,ALL 1 SNA

...4 6001-002621 SCREW-MACHINE;BH,+,M4,L8,ZPC(BLK),SWRCH1 4 SA











..3 SC05 BN63-07802B COVER-STAND;42PD490,PC+ABS,V0,BK23,GF 20 1 SNA

...4 0103-005041 RESIN-PC;V0,PC+ABS 704 SNA



1 BN91-05862J ASSY SHIELD;PD450/490 43 1 SNA

.2 T0081 6001-002606 SCREW-MACHINE;PH,+,WSP,M3,L10,NI PLT,SWR 8 SA






.2 CB25A BN96-16790A ASSY BRACKET P-WALL;PD450/490,SECC,T0.2 4 SNA



.2 SB05A BN96-16791A ASSY BRACKET P-STAND LINK;PD450/490 43,S 1 SNA

..3 BN61-02429P STUD-PEM;PC7000,M3.8,D8,L11,ZPC(SIL),SUM 6 SNA

..3 BN61-02429S STUD-PEM;PD490,M3,D7,L10.5,ZPC(SIL),SUM2 1 SNA


..3 CD101 BN65-00005A CLAMP-WIRE;55UD6500,NYLON6.6 3 SNA


..3 BN60-00033B SPACER-FELT;PD450,L30mm,BLK,T0.35mm,W15m 1 SNA


1 BN91-07198X ASSY PDP;PS43D450A2WXXN 1 SNA


.2 P001A BN44-00442B DC VSS-PDP;PB4,AC/DC,AC100~240V,50/60Hz, 1 SA


.2 M0014 BN94-04884A ASSY PCB MISC-MAIN;PS43D450*,XC,XN,Z,ZG, 1 SA

..3 0202-001557 SOLDER-CREAM;LST57-A,D38-63,42SN/57BI/1A 3 SNA


..3 BN97-05844E ASSY SMD;D550 XC,XN,ZF,ZG,ZT,TK,BN41-016 1 SNA




...4 0403-001561 DIODE-ZENER;MMSZ5226B,3.135/3.465V(5%),5 1 SA









...4 Q101 0501-000445 TR-SMALL SIGNAL;KTC3875S-Y,NPN,150mW,SOT 6 SA






















...4 1204-003240 IC-DECODER;SEMS20-LF,HSBGA,572P,20x20mm, 1 SNA




...4 1405-001271 VARISTOR;20Vdc,5A,1.0x0.5x0.6mm,TP 5 SA


...4 R105 2007-000138 R-CHIP;100ohm,5%,1/16W,TP,1005 30 SA








...4 2007-000160 R-CHIP;68Kohm,5%,1/16W,TP,1005 2 SA














...4 2007-001168 R-CHIP;75ohm,5%,1/4W,TP,3216 2 SA









...4 2007-007138 R-CHIP;27Kohm,1%,1/16W,TP,1005 1 SA


...4 2007-007156 R-CHIP;1ohm,5%,1/16W,TP,1005 14 SNA

...4 2007-007311 R-CHIP;22Kohm,1%,1/16W,TP,1005 1 SA



...4 2007-007463 R-CHIP;1.1Kohm,1%,1/16W,TP,1005 1 SA

...4 2007-007517 R-CHIP;240ohm,1%,1/16W,TP,1005 2 SNA





...4 2007-008649 R-CHIP;220ohm,1%,1/16W,TP,1005 1 SNA























...4 AD480 2203-001412 C-CER,CHIP;0.03nF,5%,50V,NP0,1005 8 SNA














...4 C23 2203-006890 C-CER,CHIP;10000nF,20%,6.3V,X5R,1608 29 SA







...4 2703-003890 INDUCTOR-SMD;47uH,10%,3225 1 SA





...4 DR32 3301-000314 BEAD-SMD;120ohm,1.6x0.8x0.8mm,-,-,- 7 SNA

...4 T0568 3301-001148 BEAD-SMD;60ohm,1608,TP 3 SNA


...4 3701-001591 CONNECTOR-HDMI;19P,2ROW,FEMALE,SMD-S,AU 2 SA







...4 3709-001640 CONNECTOR-CARD SLOT;68P(U/S) W/L,1.27mm, 1 SA








...4 ET01 BN40-00220A TUNER;DTM-8B/125S,DTM-8B/125S,DVB-T Half 1 SA

...4 BN41-01632C PCB MAIN;PDP D450/D490/D550 EU,FR-4,4,1. 1 SNA

...4 BN97-05171E ASSY MICOM-SUB;T-MSTxDEUS 1 SNA


...4 BN97-05500D ASSY MICOM-E-MANUAL;PX5DVBEU4A-0000,BN46 1 SNA

....5 1107-001990 IC-NAND FLASH;KFG1GN6W2D-HIB6,1Gbit,64Mx 1 SA

....5 BN46-00044A S/W-E-MANUAL;PDP X5 DVB,EU4,8 Langs 1 SNA

....5 BN46-00060A S/W MICOM;T-MST4DEUC,EU,Eng/Swe/Dan/Nor/ 1 SNA



.2 U001A BN96-16470A ASSY PDP MODULE P;S42AX-YB11,PL42AF080A, 1 SA


































..3 6902-001340 BAG PE;LDPE,T0.05,W250,L350,TRP,RECYCLE 1 SNA


..3 M9889 BN63-01798B CLOTH-CLEAN;cloth,180,200,sea blue,ToC 1 SNA


..3 6902-000476 BAG PE;LDPE,T0.03,W250,L350,TRP,Recycle, 1 SNA










Parts List



SA 1


SNA 1


SA 1

2 BN91-07198U 2 U001A BN96-18206A ASSY PDP MODULE P;S42AX-YD15,PP42AF085A,

SA 1


SA 1


SNA 2


SNA 1

6 BN91-07198U 2 M0014 BN94-04502Q ASSY PCB MISC-MAIN; 45043",TC,XC,XN,ZF,Z

SA 1


SNA 4

8 BN91-05862N 2 SB05A BN96-16791A ASSY BRACKET P-STAND LINK;PD450/490 43,S

SNA 1

9 BN96-17865B 3 RB01 BN63-07786B COVER-BOTTOM; PD55050",HIPS,V0,BLK

SNA 1


SA 1

11 BN90-03302C 2 SG03A BN96-16786C ASSY STAND P-GUIDE; PD450/49043,PC G/F 2

SA 1


SA 1















...4 0103-007268 RESIN-PC;TP0010,2.0V0,NH PC,NH PC 2.0 V2 618 SNA






..3 BN63-04499A FELT;P450 42,FELT,0.5,15,360 2 SNA






.2 SG03A BN96-16786C ASSY STAND P-GUIDE;PD450/490 43,PC G/F 2 1 SA






..3 BN96-18013F ASSY ACCESSORY-SCREW;6001-002621,4EA,ALL 1 SNA

...4 6001-002621 SCREW-MACHINE;BH,+,M4,L8,ZPC(BLK),SWRCH1 4 SA











..3 SC05 BN63-07802B COVER-STAND;42PD490,PC+ABS,V0,BK23,GF 20 1 SNA

...4 0103-005041 RESIN-PC;V0,PC+ABS 704 SNA




.2 T0081 6001-002606 SCREW-MACHINE;PH,+,WSP,M3,L10,NI PLT,SWR 4 SA






.2 CB25A BN96-16790A ASSY BRACKET P-WALL;PD450/490,SECC,T0.2 4 SNA



.2 SB05A BN96-16791A ASSY BRACKET P-STAND LINK;PD450/490 43,S 1 SNA

..3 BN61-02429P STUD-PEM;PC7000,M3.8,D8,L11,ZPC(SIL),SUM 6 SNA

..3 BN61-02429S STUD-PEM;PD490,M3,D7,L10.5,ZPC(SIL),SUM2 1 SNA


..3 CD101 BN65-00005A CLAMP-WIRE;55UD6500,NYLON6.6 3 SNA

.2 B001A BN96-17865B ASSY COVER P-BOTTOM;PD450 43/51,HIPS,V0, 1 SNA

..3 BN60-00033B SPACER-FELT;PD450,L30mm,BLK,T0.35mm,W15m 1 SNA

..3 RB01 BN63-07786B COVER-BOTTOM;PD550 50",HIPS,V0,BLK 1 SNA

1 BN91-07198U ASSY PDP;PS43D4 1 SNA


.2 BN81-01805D A/S-TAPE-FILAMENT;ELMATIT,T0.1,W30,L1200 0 SNA

.2 M0014 BN94-04502Q ASSY PCB MISC-MAIN;450 43",TC,XC,XN,ZF,Z 1 SA

..3 0202-001557 SOLDER-CREAM;LST57-A,D38-63,42SN/57BI/1A 3 SNA


..3 BN97-05274Q ASSY SMD;450 43",TC,XC,XN,ZF,ZG,ZT,TK,BN 1 SNA










...4 Q101 0501-000445 TR-SMALL SIGNAL;KTC3875S-Y,NPN,150mW,SOT 6 SA
























...4 1204-003240 IC-DECODER;SEMS20-LF,HSBGA,572P,20x20mm, 1 SNA




...4 1405-001271 VARISTOR;20Vdc,5A,1.0x0.5x0.6mm,TP 5 SA


...4 R105 2007-000138 R-CHIP;100ohm,5%,1/16W,TP,1005 30 SA








...4 2007-000160 R-CHIP;68Kohm,5%,1/16W,TP,1005 2 SA














...4 2007-001168 R-CHIP;75ohm,5%,1/4W,TP,3216 2 SA









...4 2007-007138 R-CHIP;27Kohm,1%,1/16W,TP,1005 1 SA


...4 2007-007156 R-CHIP;1ohm,5%,1/16W,TP,1005 14 SNA

...4 2007-007311 R-CHIP;22Kohm,1%,1/16W,TP,1005 1 SA



...4 2007-007463 R-CHIP;1.1Kohm,1%,1/16W,TP,1005 1 SA

...4 2007-007517 R-CHIP;240ohm,1%,1/16W,TP,1005 2 SNA





...4 2007-008649 R-CHIP;220ohm,1%,1/16W,TP,1005 1 SNA





































...4 C23 2203-006890 C-CER,CHIP;10000nF,20%,6.3V,X5R,1608 29 SA







...4 2703-003890 INDUCTOR-SMD;47uH,10%,3225 1 SA





...4 DR32 3301-000314 BEAD-SMD;120ohm,1.6x0.8x0.8mm,-,-,- 7 SNA


...4 3701-001591 CONNECTOR-HDMI;19P,2ROW,FEMALE,SMD-S,AU 2 SA




...4 3709-001640 CONNECTOR-CARD SLOT;68P(U/S) W/L,1.27mm, 1 SA












...4 BN41-01632A PCB MAIN;PDP X5 PD550,FR-4,4,1.2,192x195 1 SNA




....5 1107-001990 IC-NAND FLASH;KFG1GN6W2D-HIB6,1Gbit,64Mx 1 SA





.2 U001A BN96-18206A ASSY PDP MODULE P;S42AX-YD15,PP42AF085A, 1 SA

..3 P001A BN44-00442B DC VSS-PDP;PB4,AC/DC,AC100~240V,50/60Hz, 1 SA















.2 6902-001261 BAG SHEET;HDPE/NITRON/HDPE,T0.015/T0.5,W 1 SNA
















..3 T0121 3301-002049 CORE-FERRITE;33.6X30.5,3500 2 SNA

..3 T0268 3903-000456 CBF-POWER CORD;DT,EU/KR,CP3,IEC320 C13-R 1 SA


..3 6902-001340 BAG PE;LDPE,T0.05,W250,L350,TRP,RECYCLE 1 SNA


..3 M9889 BN63-01798B CLOTH-CLEAN;cloth,180,200,sea blue,ToC 1 SNA


..3 6902-000476 BAG PE;LDPE,T0.05,W250,L350,TRP,Recycle, 1 SNA









Parts List



SA 1


SNA 1


SA 1

2 BN91-07198Z 2 U001A BN96-18206B ASSY PDP MODULE P;S42AX-YD15,PP42AF087B,

SC 1


SA 1


SNA 2


SNA 1

6 BN91-07198Z 2 M0014 BN94-04884A ASSY PCB MISC-MAIN;PS43D450*,XC,XN,Z,ZG,

SA 1


SA 4


SA 1


SC 1


SA 1


SA 1


SA 1































...4 0103-007285 RESIN-PC;MW32020GFU,K032202GFV,BK0007,V2 200 SNA




















..3 M0019 BN73-00052C RUBBER-FOOT;LCD TV,Silicone RUBBER,T2.0 6 SNA












...4 0103-004609 RESIN-ABS;HF-0680U,K21294,BK0007,1.5mm H 16 SNA







..3 RB01 BN63-07786C COVER-BOTTOM;PD550 50",NH HIPS,V1,BLK 1 SC


1 BN91-07198Z ASSY PDP;PS43D450A2WXXN 1 SNA



.2 M0014 BN94-04884A ASSY PCB MISC-MAIN;PS43D450*,XC,XN,Z,ZG, 1 SA

..3 BN97-05844E ASSY SMD;D550 XC,XN,ZF,ZG,ZT,TK,BN41-016 1 SNA



































...4 1204-003240 IC-DECODER;SEMS20-LF,HSBGA,572P,20x20mm, 1 SA




...4 1405-001271 VARISTOR;35V,20Vdc,5A,1.0x0.5x0.6mm,TP,1 5 SA


...4 R105 2007-000138 R-CHIP;100ohm,5%,1/16W,TP,1005 30 SA








...4 2007-000160 R-CHIP;68Kohm,5%,1/16W,TP,1005 2 SA














...4 2007-001168 R-CHIP;75ohm,5%,1/4W,TP,3216 2 SA









...4 2007-007138 R-CHIP;27Kohm,1%,1/16W,TP,1005 1 SA


...4 2007-007156 R-CHIP;1ohm,5%,1/16W,TP,1005 12 SNA

...4 2007-007311 R-CHIP;22Kohm,1%,1/16W,TP,1005 1 SA



...4 2007-007463 R-CHIP;1.1Kohm,1%,1/16W,TP,1005 1 SA

...4 2007-007517 R-CHIP;240ohm,1%,1/16W,TP,1005 2 SNA





...4 2007-008649 R-CHIP;220ohm,1%,1/16W,TP,1005 1 SNA




















...4 AD480 2203-000714 C-CER,CHIP;3.3nF,10%,50V,X7R,TP,1005 6 SA














...4 HE4 2203-006474 C-CER,CHIP;22000nF,20%,6.3V,X5R,TP,2012 12 SA














...4 2901-001658 FILTER-EMI SMD;5V,0.13A,2.0x1.0x0.5mm,TP 2 SNA


...4 T0568 3301-001148 BEAD-SMD;60ohm,1608,TP 3 SNA


















...4 BN41-01632C PCB MAIN;PDP D450/D490/D550 EU,FR-4,4,1. 1 SNA




....5 1107-001990 IC-NAND FLASH;KFG1GN6W2D-HIB6,1Gbit,64Mx 1 SNA








.2 U001A BN96-18206B ASSY PDP MODULE P;S42AX-YD15,PP42AF087B, 1 SC


..3 UL01A BN96-16507B ASSY PDP P-LOGIC MAIN BOARD;S42AX-YB11,L 1 SA



..3 UX03A BN96-16510B ASSY PDP P-X-MAIN BOARD;S42AX-YB11,LJ92- 1 SA










.2 6902-001668 BAG ROLL;HDPE/NITRON,T0.3,W1100,L450M,TR 3 SNA








.2 BN63-08890P COVER-SHEET NITRON;LS19CLYSB,PE,T2.0,114 1 SNA

.2 BN63-09096A COVER-PALLET FOIL;32D550,PE,T0.03,2000,2 1 SNA




.2 BN69-05929A WRAP STRETCH FILM;All,LDPE,0.0066,440,42 7 SNA

.2 BN69-06338B PALLET-WOODEN;UE37D6510,WOOD,1080,1120,1 1 SNA














..3 BN68-03019A LEAFLET-01,SAFETY GUIDE;ALL,SAMSUNG,28LE 1 SNA


..3 BN68-03943G LEAFLET-FICHE_PDP;ALL,SAMSUNG,ENG,ALL,W/ 1 SNA





Samsung ps43d450a2wxzg chassis_f82a_sm

Documents

Transcript of Samsung ps43d450a2wxzg chassis_f82a_sm