RRH.pdf

7/17/2019 RRH.pdf

http://slidepdf.com/reader/full/rrhpdf 1/68

Title page

Alcatel-LucentRemote Radio Head 2X60W - 850, 1900 MHz

Maintenance Guide

3MN-01477-0004-REZZAIssue 0.02 | January 2014

Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements

7/17/2019 RRH.pdf


Legal notice

Legal notice

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective

owners.

The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.

Copyright © 2014Alcatel-Lucent. All rights reserved.

Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside

Alcatel-Lucent without its written authorization.

Not to be used or disclosed except in accordance with applicable agreements.


P R E L I M I N A R Y

P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Contents

About this document

Purpose ............................................................................................................................................................................................. xixi

Reason for reissue ........................................................................................................................................................................ xixi

Intended audience ....................................................................................................................................................................... xiixii

Supported systems ...................................................................................................................................................................... xiixii

How to use this document ........................................................................................................................................................ xiixii

Safety information ......................................................................................................................................................................

xiixii

Prerequisites .................................................................................................................................................................................. xiixii

Conventions used ........................................................................................................................................................................ xiixii

Related information ................................................................................................................................................................... xiiixiii

Document support ....................................................................................................................................................................... xvxv

Technical support ......................................................................................................................................................................... xvxv

How to order .................................................................................................................................................................................. xvxv

How to comment .......................................................................................................................................................................... xvxv

1 Safety statements

Overview ...................................................................................................................................................................................... 1-11-1

Structure of safety statements ............................................................................................................................................... 1-21-2

2 Preventive maintenance

Overview ...................................................................................................................................................................................... 2-12-1

Preventive maintenance activity .......................................................................................................................................... 2-22-2

3 Corrective maintenance

Overview ...................................................................................................................................................................................... 3-13-1

Corrective maintenance ......................................................................................................................................................... 3-23-2

....................................................................................................................................................................................................................................

Alcatel-Lucent RRH 2X60W3MN-01477-0004-REZZAIssue 0.02 January 2014


iii

PRELI M

I NARY

PRELI MI NARY

7/17/2019 RRH.pdf


4 Introduction

Overview ...................................................................................................................................................................................... 4-14-1

RRH 2X60W solution ............................................................................................................................................................. 4-24-2

5 Hardware description

Overview ...................................................................................................................................................................................... 5-15-1

RRH 2X60-1900/1900A hardware description .............................................................................................................. 5-25-2

RRH 2X60-850 and hardware description ...................................................................................................................... 5-75-7

Node B hardware requirements for RRH support ...................................................................................................... 5-115-11

6 Power up and power down procedures

Overview ...................................................................................................................................................................................... 6-16-1

Powering up an RRH 2X60W .............................................................................................................................................. 6-26-2

Powering down an RRH 2X60W ........................................................................................................................................ 6-46-4

7 Preventive maintenance procedures

Overview ...................................................................................................................................................................................... 7-17-1

Inspecting connectors .............................................................................................................................................................. 7-27-2

Inspecting pole brackets and pole bands .......................................................................................................................... 7-47-4

8 Corrective maintenance procedure

Overview ...................................................................................................................................................................................... 8-18-1

Replacing an RRH 2X60W ................................................................................................................................................... 8-28-2

A Product conformance statements

Overview ..................................................................................................................................................................................... A-1A-1

European regulatory requirement compliance .............................................................................................................. A-2A-2

Americas Region regulatory requirement compliance ............................................................................................... A-4A-4

Federal Communications Commission ............................................................................................................................ A-5A-5

Compliances for other regions/countries ........................................................................................................................ A-7A-7

Operating conditions .............................................................................................................................................................. A-8A-8

Contents

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

iv Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements

Alcatel-Lucent RRH 2X60W3MN-01477-0004-REZZA

Issue 0.02 January 2014 P R E L I M I N A R Y

P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Cable specifications ................................................................................................................................................................ A-9A-9

Product labeling ..................................................................................................................................................................... A-10A-10

Index

Contents

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



v

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Contents

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

vi Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


List of tables

1 Issue 0.02, January 2014, Reason for reissue .................................................................................................... xixi

2 Issue 0.01, April 2013, Reason for reissue .......................................................................................................... xixi

3-1 RRH 2X60W orderable items ............................................................................................................................... 3-23-2

....................................................................................................................................................................................................................................



vii

PRELI M

I NARY

PRELI MI NARY

7/17/2019 RRH.pdf


List of tables

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

viii Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


List of figures

4-1 Connections between RRH 2X60W and a d2U Node B ............................................................................. 4-24-2

5-1 RRH 2X60-1900 two antennas bulkhead top view ....................................................................................... 5-25-2

5-2 RRH 2X60-1900A four antennas bulkhead top view ................................................................................... 5-35-3

5-3 RRH 2X60-1900/1900A bulkhead bottom view ............................................................................................ 5-45-4

5-4 RRH 2X60-850 two antennas bulkhead top view ......................................................................................... 5-75-7

5-5 RRH 2X60-850 bulkhead bottom view ............................................................................................................. 5-85-8

7-1 Pole brackets and pole bands ................................................................................................................................

7-57-5

....................................................................................................................................................................................................................................



ix

PRELI M

I NARY

PRELI MI NARY

7/17/2019 RRH.pdf


List of figures

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

x Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


About this documentAbout this document

Purpose

The purpose of this document is to describe the preventive and corrective procedures

applicable to the following Alcatel-Lucent Remote Radio Head variants:

• 2X60W, 850 MHz

•

2X60W, 1900 MHz• 2X60W, 1900A MHz

Reason for reissue

The reissue history for issue 0.02 is shown in the following table:

Table 1 Issue 0.02, January 2014, Reason for reissue

Location Change

Reason for reissue LR13.3W:FRS 165530 - RRH2x60-1900A (4 antennas) with

9396 digital units

Related information CR 01145957 + CR 01145972 (old references of documents)

The reissue history for issue 0.01 is shown in the following table:

Table 2 Issue 0.01, April 2013, Reason for reissue

Location Change

None First issue as release-independent document (from NN20500-308,

Release: UA08.1), with updated comments.

The decision has been made to split the document NN20500-308into 2 documents:

- one specific to AT&T: the present document (3MN-01477-0004-

REZZA)

- the other one specific to GM customers

...................................................................................................................................................................................................................................



xi

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Intended audience

The audience for this document is Operations and maintenance personnel.

Supported systems

This release-independent document applies to all Alcatel-Lucent W-CDMA system

releases.

How to use this document

No specific recommendation applies regarding the way readers should read this

document.It applies to the AT&T dedicated products and configuration WCDMA with

9396 d2U or d4U OneBTS.

Safety information

For your safety, this document contains safety statements. Safety statements are given at

points where risks of damage to personnel, equipment, and operation may exist. Failure tofollow the directions in a safety statement may result in serious consequences.

Prerequisites

It is recommended that readers become familiar with the following documents:

• Alcatel-Lucent Remote Radio Head 2X60W - 850, 1900 MHz for W-CDMA -

Technical Description, 3MN-01477-0003-DEZZA

Conventions used

Vocabulary conventionsFor a list of the terms, see Alcatel-Lucent W-CDMA System - Terminology,

9YZ-04088-0002-TQZZA.

For convenience, the following terms are used in this publication:

• RRH 2X60-850, RRH 2X60-1900, RRH 2X60-1900A

• RRH 2X60W

• RRH

Typographical conventions

The following typographical conventions are used in this document:

Appearance Description

Italicized text Emphasized information

graphical user interface text Text that is displayed in a graphical user

interface or in a hardware label.

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

xii Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Appearance Description

Document reference, reference number Related document that is referenced in the

document

Related information

For information on subjects related to the content of this document, refer to the

documents listed in the following table:

For information on subjects related to the content of this document, refer to the

documents listed in the following table:

Refer to this document At this location For more information on

RRH2X60-XX Model Offer

Provisioning Guide,

UMT/PFO/APP/032664

http://support.alcatel-lucent.

com.

RRH2x

Alcatel-Lucent W-CDMA

System - Safety Guide,

9YZ-04088-0007-TQZZA


com.

Safety guidelines and the

catalog of hazard statements

that appear in the

Alcatel-Lucent UMTS

customer documents.

RRH Product Engineering

Information ,

UMT/IRC/APP/020716


com.

RRH configurations

Alcatel-Lucent Remote Radio

Head 2X60 W - 850, 1900

MHz - Technical Description,

3MN-01477-0003-DEZZA


com.

RRH technical description

Alcatel-Lucent Remote Radio

Head 2X60 W - 850,

1900MHz - Hardware

Installation,

3MN-01477-0002-RJZZA


com.

RRH installation

Alcatel-Lucent 9396 digital

2U Node B - Technical

Description,3MN-00514-0005-DEZZA


com.

d2U technical description


4U Node B - Technical

Description,

3MN-00512-0005-DEZZA


com.

d4U technical description

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



xiii

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf




2U Node B - Hardware

Installation,

3MN-00514-0004-RJZZA


com.

d2U hardware installation


4U Node B - Hardware

Installation,

3MN-00512-0004-RJZZA


com.

d4U hardware installation


2U Node B - Installation Test,

3MN-00514-0003-RJZZA


com.

d2U installation test


4U Node B - Installation Test,

3MN-00512-0003-RJZZA


com.

d4U installation test


2U Node B - Operations,

Administration, and

Maintenance,

3MN-00514-0006-REZZA


com.

d2U operation, administration

and maintenance


4U Node B - Operations,

Administration, and

Maintenance,

3MN-00512-0006-REZZA


com.

d4U operation, administration

and maintenance

Alcatel-Lucent 9353 Wireless

Management System – Fault

Management,

9YZ-04088-0010-ACZZA


com.

Fault management

W-CDMA FIMS-UT Main

Maintenance Terminal Online

Help


com.

Main maintenance terminal

W-CDMA Remote

Maintenance Tool Online

Help


com.

Remote maintenance tool

W-CDMA Local Maintenance

Terminal Online Help


com.

Local maintenance terminal

Standard for Installation of

Lightning Protection Systems,

NFPA


com.

Installation of lightning

protection systems

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

xiv Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf



Recommended Practices on

Surge Voltages in Low Voltage

AC Power Circuits, IEEE

C62.41 (Latest Edition)


com.

Power

Document support

For support in using this or any other Alcatel-Lucent document, contact Alcatel-Lucent at

one of the following telephone numbers:

• 1-888-582-3688 (for the United States)

• 1-630-224-2485 (for all other countries)

Technical support

For technical support, contact your local Alcatel-Lucent customer support team. See theAlcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact

information.

How to order

To order Alcatel-Lucent documents, contact your local sales representative or use Online

Customer Support (OLCS) (http://support.alcatel-lucent.com)

How to comment

To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-lucent.com/comments/) or e-mail your comments to the Comments Hotline

([email protected]).

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



xv

PRELI MI NA

RY

PRELI MI NARY

http://www.alcatel-lucent.com/support/


http://infodoc.alcatel-lucent.com/comments/




mailto:[email protected]









7/17/2019 RRH.pdf


About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

xvi Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


1 1Safety statements

Overview

Purpose

This chapter provides information on the structure of safety statements which may arise

in the course of your work.

Contents

Structure of safety statements 1-2

...................................................................................................................................................................................................................................



1-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Structure of safety statements

Overview

This topic describes the components of safety statements that appear in this document.

General structure

Safety statements include the following structural elements:

Item Structure element Purpose

1 Safety alert symbol Indicates the potential for personal injury

(optional)

2 Safety symbol Indicates hazard type (optional)

3 Signal word Indicates the severity of the hazard

4 Hazard type Describes the source of the risk of damage or

injury

5 Safety message Consequences if protective measures fail

6 Avoidance message Protective measures to take to avoid the hazard

7 Identifier The reference ID of the safety statement

(optional)

SA M P L E

B C D

E F

G

H

Lifting this equipment by yourself can result in injury

due to the size and weight of the equipment.

Always use three people or a lifting device to transport and position this equipment. [ABC123]

CAUTION

Lifting hazard

Safety statements Structure of safety statements

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1-2 Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Signal words

The signal words identify the hazard severity levels as follows:

Signal word Meaning

DANGER Indicates an extremely hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION Indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

NOTICE Indicates a hazardous situation not related to personal injury.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1-3

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf



....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


2 2Preventive maintenance

Overview

Purpose

This chapter describes the preventive maintenance activity applicable to the RRH

2X60W.

Contents

Preventive maintenance activity 2-2

...................................................................................................................................................................................................................................



2-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Preventive maintenance activity

Preventive maintenance

The preventive maintenance is used to periodically test the items of equipment that do not

directly trigger any alarm at the WMS. However, the execution of preventive maintenance procedures can trigger alarms at the WMS.

These procedures must be performed according to the following schedules.

It is possible to group some of the procedures, which reduces the intervention time. The

intervention time indicated corresponds to the intervention time for each item of

equipment.

Note: In certain environments, these procedures may be required more frequently:

• Systems located in high seismic areas may require anchor bolts and mounting

hardware to be tightened periodically especially for field installed items.

• Connectors may require periodic cleaning in dirty and high humidity areas.

Preventive maintenance schedule for RRH 2X60W equipment

Procedure Periodicity Test duration(approx.)

“Inspecting connectors” (p. 7-2) Every two years 10 minutes

“Inspecting pole brackets and pole bands”

(p. 7-4)

Every two years 10 minutes

Preliminary checks before performing preventive maintenance procedures

WARNING

Personal injury hazard

The personnel working on the cabinet must be authorized to work according to the

applicable safety standards

Preventive maintenance Preventive maintenance activity

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


NOTICE

ESD hazard

Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit

packs only at the edges or on the insertion and removal facilities. Always observe the

general ESD instructions.

Description of a preventive maintenance procedure

A preventive maintenance procedure is divided into the following parts:

• Title

• Main body with following information:

– Intervention time

– Tools required

– Step-by-step actions

– One or more figures to help you execute the actions


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



2-3

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf



....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


3 3Corrective maintenance

Overview

Purpose

This chapter describes the corrective maintenance activity applicable to the RRH 2X60W.

Contents

Corrective maintenance 3-2

...................................................................................................................................................................................................................................



3-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Corrective maintenance

Corrective maintenance activity

The network maintenance is based on the supervision of the network, by using the OAM

graphical interface. For more information, see Alcatel-Lucent 9353 Wireless Management System - User Guide, 9YZ-04088-0014-PCZZA.

It is also based on the identification and replacement of faulty items of equipment, using

the alarms.

The process consists of two steps:

1. Locating and identifying the faulty RRH 2X60W through alarms at the WMS. See

"Fault management" chapter in Alcatel-Lucent 9353 Wireless Management System -

User Guide, 9YZ-04088-0014-PCZZA.

2. Replacing the faulty RRH 2X60W following the replacement procedure detailed in

this publication.

RRH 2X60W replacement

In the case of the RRH 2X60W, no separate module replacement exists: the whole RRH

2X60W is to be replaced. The procedure is detailed in “Replacing an RRH 2X60W”

(p. 8-2).

The following table indicates the orderable item (code) for each module or item to be

replaced from the RRH 2X60W variants.

Table 3-1 RRH 2X60W orderable items

RRH 2X60W

module/item

Orderable item Provisioning rule

SFP Optical Transceiver

Multi Mode, Dual Fiber

1AB187280063 One SFP per RRH to be installed in

CPRI_PRI.


Single Mode, Single Fiber

1AB194670019 If single-mode: provide one SFP per

RRH to be installed in CPRI_PRI.


Single Mode, Dual Fiber

1AB187280065 One SFP per RRH to be installed in

CPRI_PRI.

Cable alarm connectorized

-15M

849138136 One if external alarm option is required

For optional orderable items, see the following documents:

• RRH 2X60-XX Model Offer Provisioning Guide, UMT/PFO/APP/032664

Corrective maintenance Corrective maintenance

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Description of a replacement procedure

A replacement procedure is divided into the following parts:

• Title

• Main body with the following information:

– Intervention time – Tools required

– Impact of the procedure, if necessary

– Step-by-step actions

One or more figures are provided to help you execute the actions.

Intervention restrictions

There may be a lapse of time between the identification of the alarm at the Access OAM

Graphic User Interface (GUI) and the time you arrive at the site.

You must be synchronized with the access network controller or system administrator (by

telephone) before an on-site intervention, in the following cases:

• Isolating procedures

• Completion of an on-site intervention

• Return to service procedure

General personnel safety instructions

The personnel must obey the safety instructions specific to the installation site:

• Rules concerning the premises (see instructions posted on site or in the building)

• Rules linked to general personnel safety instructions

The personnel working on the cabinet must be authorized to work according to security

standards.

Equipment safety instructions

The external temperature must be comprised between – 40°C and + 50°C.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



3-3

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf



....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


4 4Introduction

Overview

Purpose

This chapter presents the RRH 2X60W solution.

Contents

RRH 2X60W solution 4-2

...................................................................................................................................................................................................................................



4-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


RRH 2X60W solution

RRH 2X60W overview

The RRH 2X60W is a solution for a remote RF transceiver that can be located far away

(500 m to 20 km) from a main Node B and interface with this main Node B through anoptical fiber.

The RRH 2X60W provides an external optical interface to be connected to the optical

module of the main Node B.

It also provides an external radio interface according to UMTS standards.

The following figure shows the connections between RRHs and a d2U Node B in star

configuration.

For details concerning the configurations of implementation, refer to chapter 3 in the

document: Alcatel-Lucent Remote Radio Head 2X60W - 850, 1900 MHz - Technical

Description, 3MN-01477-0003-DEZZA.

Figure 4-1 Connections between RRH 2X60W and a d2U Node B

Introduction RRH 2X60W solution

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


5 5Hardware description

Overview

Purpose

This chapter describes:

• The RRH bulkhead hardware• The connectivity

• The LED indicators

It also specifies the Node B hardware requirements for RRH support.

Contents

RRH 2X60-1900/1900A hardware description 5-2

RRH 2X60-850 and hardware description 5-7

Node B hardware requirements for RRH support 5-11

...................................................................................................................................................................................................................................



5-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


RRH 2X60-1900/1900A hardware description

Bulkhead description

The following figure shows the top view of the RRH 2X60-1900 bulkhead:

Figure 5-1 RRH 2X60-1900 two antennas bulkhead top view

Hardware description RRH 2X60-1900/1900A hardware description

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


The following figure shows the top view of the RRH 2X60-1900A bulkhead:

Figure 5-2 RRH 2X60-1900A four antennas bulkhead top view


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



5-3

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


The following figure shows the bottom view of the RRH 2X60-1900/1900A bulkhead:

Connector description

This topic gives an overview of the connectors located on the RRH bulkhead.

Interface Connector

Power –48 V DC

GND Ground connectionALD (Antenna Line Device) Antenna power and control

1 AISG (RS485) connector

8-pin Circular Din female connector

Support of RETA compatible with AISG 2.0.

Figure 5-3 RRH 2X60-1900/1900A bulkhead bottom view


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Interface Connector

TX1/RX1 Transmit and receive antenna path

7/16 DIN coaxial female connector for the

connection with the antenna

TX2/RX2 Receive diversity antenna path


connection with the diversity antenna

ALM1-3, ALM 4-6 External user alarms connector

Six user alarms

Implemented with 2 X 8-pin circular DIN

female connectors .

CPRI _PRI CPRI optical port

Used to connect the RRH to the Node B or

another RRH

SFP, with waterproof Radiall flange connector

(which includes the protective metal cover)

CPRI_SEC CPRI optical port

Used to connect the RRH to the Node B


(which includes the protective metal cover

RX3 and RX4 2 Rx ports located on the top of the RRH

2X60-1900A

RX3 and RX4 are not connected in WCDMAmode of operation, a waterproof cap protects

the unused connectors

MAINT Local maintenance terminal2 (MAINT) RJ45

connector located on the bottom of the RRH.

Notes:

1. A reset button is located next to the MAINT port.

LED description (STATUS)

There is only one green-red-yellow tri-colored LED. The Base Band Unit (BBU) gets the

LED status periodically and reports it to the management system.

The table below summarizes these states in priority order, from highest (1) to lowest (13).


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



5-5

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Note that one states in the table is marked as not applicable (‘n/a’) for the single LED

display (Background download). In these cases no LED setting is assigned and so the

LED setting defaults to the next lower priority active setting.

ID RTU State Description LED

Display

1 No power Supplied. No AC or DC power (dead unit). Off

2 Initial power On. RTU is initializing. Solid Red

3 External Power Supply

Failure.

AC or DC input power feed is out of range. Flash Red

4 Software download. The unit is downloading software and RF

transmission is off, but is currently

operational.

Flash Yellow

5 Nonrecoverable Critical

Failure.

A critical hardware failure prevents either the

transmit path or the active receive paths (or all paths) from functioning.

Solid Red

6 Recoverable Critical

Failure.

The unit is not currently operational due to

hardware fault, but should recover (e.g.,

Under-Temperature Warm-Up or

Over-Temperature Critical Shutdown.

Flash Red

7 CPRI_PRI link Failure. CPRI_PRI link has failed. Solid Yellow

8 Non-Critical

Nonrecoverable

Failure.

Non-Critical fault (other than antenna)

detected, fault is not recoverable, transmission

is still on.

Solid Red

9 Non-Critical

Recoverable Failure.


detected, fault is recoverable, transmission is

still on.

Flash Red

10 ExternalAntenna

Failure.

An equipped antenna has a VSWR fault. Flash Red

11 Background Software

Download.

A background software download is in

progress, RF is currently enabled.

n/a

12 Normal Operation. No critical failures or faults, transmitter is

enabled.

Solid Green

13 Standby. No critical failures or faults, but the transmitter is disabled.

Flash Green


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


RRH 2X60-850 and hardware description

Bulkhead description

The following figures show the top view of the RRH 2X60-850 bulkhead:

Figure 5-4 RRH 2X60-850 two antennas bulkhead top view

Hardware description RRH 2X60-850 and hardware description

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



5-7

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


The following figure shows the bottom view of the RRH 2X60-850 bulkhead:

Connector description

This topic gives an overview of the connectors located on the RRH bulkhead.

Interface Connector

Power –48 V DC

GND Ground connection

ALD (Antenna Line Device) Antenna power and control

1 AISG (RS485) connector

8-pin Circular Din female connector

Support of RETA compatible with AISG 2.0.

Figure 5-5 RRH 2X60-850 bulkhead bottom view


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Interface Connector

TX/RX Transmit and receive antenna path


connection with the antenna

ALM1-3, ALM4-6 External user alarms connector

Six user alarms

Implemented with 2 X 8-pin circular DIN

female connectors (same as AISG).

CPRI _PRI CPRI optical port

Used to connect the RRH to the Node B or

another RRH


(which includes the protective metal cover)

CPRI_SEC CPRI optical port

Used to connect the RRH to the Node B


(which includes the protective metal cover

AUX Rx Two AUX ports1 (AUX_RX1, AUX_RX2)

SMA female connector

MAINT Local maintenance terminal2 (MAINT) RJ45

connector located on the bottom of the RRH

2X60-850.

Notes:

1. The two AUX SMA ports are used for antenna sharing feature. They can be configured as

RX ports to bypass the Low Noise Amplifier (LNA) and filters inside the RRH. They also

can be configured as TX ports to output received signal of the main RX ports with 25 dB

gain.

2. A reset button is located next to the MAINT port.

LED description (STATUS)

There is only one green-red-yellow tri-colored LED. The Base Band Unit (BBU) gets the

LED status periodically and reports it to the management system.

The table below summarizes these states in priority order, from highest (1) to lowest (13).


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



5-9

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Note that one states in the table is marked as not applicable (‘n/a’) for the single LED

display (Background download). In these cases no LED setting is assigned and so the

LED setting defaults to the next lower priority active setting.

ID RTU State Description LED

Display

1 No power Supplied. No AC or DC power (dead unit). Off

2 Initial power On. RTU is initializing. Solid Red

3 External Power Supply

Failure.

AC or DC input power feed is out of range. Flash Red

4 Software download. The unit is downloading software and RF

transmission is off, but is currently

operational.

Flash Yellow

5 Nonrecoverable Critical

Failure.

A critical hardware failure prevents either the

transmit path or the active receive paths (or all paths) from functioning.

Solid Red

6 Recoverable Critical

Failure.

The unit is not currently operational due to

hardware fault, but should recover (e.g.,

Under-Temperature Warm-Up or

Over-Temperature Critical Shutdown.

Flash Red

7 CPRI_PRI link Failure. CPRI_PRI link has failed. Solid Yellow

8 Non-Critical

Nonrecoverable

Failure.


detected, fault is not recoverable, transmission

is still on.

Solid Red

9 Non-Critical

Recoverable Failure.


detected, fault is recoverable, transmission is

still on.

Flash Red

10 ExternalAntenna

Failure.

An equipped antenna has a VSWR fault. Flash Red

11 Background Software

Download.

A background software download is in

progress, RF is currently enabled.

n/a

12 Normal Operation. No critical failures or faults, transmitter is

enabled.

Solid Green

13 Standby. No critical failures or faults, but the transmitter is disabled.

Flash Green


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Node B hardware requirements for RRH support

Requirement

The following Node Bs are programmed to support RRH.

Parameter RRH 2X60 - 850/1900/1900A

BBU 9396 d2U or d4U

Hardware description Node B hardware requirements for RRH support

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



5-11

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Hardware description Node B hardware requirements for RRH support

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


6 6Power up and power down

procedures

Overview

Purpose

This chapter describes how to power up and power down the RRH 2X60W.

Contents

Powering up an RRH 2X60W 6-2

Powering down an RRH 2X60W 6-4

...................................................................................................................................................................................................................................



6-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Powering up an RRH 2X60W

Before you begin

WARNING

Electric-shock hazard

Some parts of all electrical installations are energized. Failure to follow safe work

practices and the safety warnings may lead to bodily injury and property damage.

For this reason, only trained and qualified personnel (electrical workers as defined in

IEC 60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA

No.10) may install or service the installation.

Procedure

Perform the following procedure to power up an RRH 2X60W.

...................................................................................................................................................................................................

1 Check that the circuit breaker dedicated to the RRH 2X60W is 15A.

...................................................................................................................................................................................................

2 Connect the power cable to the DC connector on the RRH 2X60W bulkhead, see Chapter

5, “Hardware description”

...................................................................................................................................................................................................

3 Connect the power cable to the power source (– 48 V DC) on the customer site.

...................................................................................................................................................................................................

4 Switch ON the circuit breaker.

...................................................................................................................................................................................................

5 Wait for RRH start-up.

...................................................................................................................................................................................................

6 Check that the status LEDs on the bulkhead display normal operation, see Chapter 5,

“Hardware description”. If a non-compliance LEDs status occurred then contact the site

coordinator before going on.

...................................................................................................................................................................................................

7 On the xCCM optical port, check that the Tx and Rx LEDs are green.

Power up and power down procedures Powering up an RRH 2X60W

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


...................................................................................................................................................................................................

8 Check with the WMS administrator if there is not unexpected alarms and that the RRH

2X60W is operational.

Power up and power down procedures Powering up an RRH 2X60W

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



6-3

PRELI MI NA

RY

PRELI MI NARY

E N D O F S T E P S...................................................................................................................................................................................................

7/17/2019 RRH.pdf


Powering down an RRH 2X60W

Before you begin

WARNING







Procedure

Perform the following procedure to power down an RRH 2X60W.

...................................................................................................................................................................................................

1 Switch OFF the circuit breaker on the customer power supply plant.

...................................................................................................................................................................................................

2 Check that the RRH 2X60W is powered off. All LEDs are OFF.

...................................................................................................................................................................................................

3 Disconnect the power cable dedicated to the RRH from the power source (-48 V DC) on

the customer site.

...................................................................................................................................................................................................

4 Unscrew the power cable from the RRH DC connector on the RRH 2X60W bulkhead, see

Chapter 5, “Hardware description”.

Power up and power down procedures Powering down an RRH 2X60W

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

E N D O F S T E P S...................................................................................................................................................................................................

7/17/2019 RRH.pdf


7 7Preventive maintenance

procedures

Overview

Purpose

This chapter contains the preventive maintenance procedures applicable to the RRH

2X60W.

Contents

Inspecting connectors 7-2

Inspecting pole brackets and pole bands 7-4

...................................................................................................................................................................................................................................



7-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Inspecting connectors

Before you begin

Intervention time: 10 minutes

Tools required: adjustable wrench

WARNING







NOTICE

Service-disruption hazard

This procedure will result in service disruption. Notify the WMS administrator of a

service outage before commencing.

Important! The personnel working on the cabinet must be authorized to work

according to the security standards.

NOTICEESD hazard




Procedure

Carry out the following procedure to inspect the connector seals on an RRH 2X60W

bulkhead.

...................................................................................................................................................................................................

1 Check the bulkhead connectors visually, see Chapter 5, “Hardware description”.

...................................................................................................................................................................................................

2 Check that connectors are well tightened.

Preventive maintenance procedures Inspecting connectors

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Result: If they move, tighten them with the adjustable wrench.

Preventive maintenance procedures Inspecting connectors

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



7-3

PRELI MI NA

RY

PRELI MI NARY

E N D O F S T E P S...................................................................................................................................................................................................

7/17/2019 RRH.pdf


Inspecting pole brackets and pole bands

Before you begin

The RRH can be installed in an outdoor environment using one of the following mounting

kits:• Floor

• Wall

• Pole (50-152 mm)

• Pole (152-380 mm)

Intervention time: 10 minutes

Tools required:

• 17-mm (11/16") socket with ratchet

• 14-mm (9/16") open-end wrench

WARNING







NOTICE




Important! The personnel working on the cabinet must be authorized to work

according to the security standards.

Preventive maintenance procedures Inspecting pole brackets and pole bands

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


NOTICE

ESD hazard




Procedure

Carry out the following procedure to check the pole brackets and pole bands of the RRH

2X60W.

...................................................................................................................................................................................................

1 Perform a visual test:

• Check that the pole brackets are well tightened to the wall bracket. If not, go to Step 2

.

• Check that the pole bands are well tightened around the pole. If not, go to Step 2.

...................................................................................................................................................................................................

2 Tighten the pole brackets and/or the pole bands.

Note: Use the 17-mm socket to tighten the pole brackets (tightening torque: 32.2

N.m).

Use the 14-mm open-end wrench to tighten the pole bands.

Figure 7-1 Pole brackets and pole bands


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



7-5

PRELI MI NA

RY

PRELI MI NARY

E N D O F S T E P S...................................................................................................................................................................................................

7/17/2019 RRH.pdf



....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


8 8Corrective maintenance

procedure

Overview

Purpose

This chapter describes the corrective maintenance procedure applicable to the RRH

2X60W.

Contents

Replacing an RRH 2X60W 8-2

...................................................................................................................................................................................................................................



8-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Replacing an RRH 2X60W

Before you begin

The replacement procedure described below is based on the following assumptions:

• An investigation was performed and it was determined that the unit to replace wasfaulty.

• The existing unit is locked at the WMS.

• To replace the RRH 2X60W main body with another RRH 2X60W, you ordered one

of the following spare parts:

– RRH 2X60-850, two antennae pre-integrated cabinet 3JR10601AA

– RRH 2X60-1900, two antennae pre-integrated cabinet 3JR10801AA

– RRH 2X60-1900A, four antennae pre-integrated cabinet 3JR39501AA

Note: For details, see Table 3-1, “RRH 2X60W orderable items” (p. 3-2)

Note: The RRH 2X60W remains supplied with the mains power supply.Note: The RRH 2X60W has an integrated handle that does not detach from the unitonce it is installed.

Intervention time:

• 30 minutes

Required tools

Tool Quantity Description,

7/16 Torque Wrench 1 Torque value: 25 Nm -1/+2

Nm / 221 lbf.in -8.8/+17.7

lbf.in

T25 TORX security drive 1

Fiber cleaning kit 1

Hexagonal Keys 1 6 mm

Screwdrivers for slotted heads 1

Set torx screwdriver 1

While the technician is on site, the local configuration data and “TTLNA” data fields are

set with the local management terminal. The technician needs to commission the RRHwith RMT. The initialization, reset, boot, software download, occur with the WMS. The

configuration of the RRH 2X60W with the proper parameter settings are also established

through the WMS. Many of the settings, commissioning data, local configuration data,

and parameters might not have to be changed at all with the replacement of a faulty unit

with a new hardware unit.

Corrective maintenance procedure Replacing an RRH 2X60W

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


WARNING







NOTICE




Important! The personnel working on the cabinet must be authorized to work according to the security standards.

NOTICE

ESD hazard




Procedure

Carry out the following procedure to replace an RRH 2X60W.

...................................................................................................................................................................................................

1 Preliminary operations:

• Shut down the RRH 2X60W, see the procedure “Powering down an RRH 2X60W”

(p. 6-4).

• Remove the solar shield, using the T25 TORX security drive, and store it in a safe

location.

• Disconnect all external cables from the bulkhead.

• Remove the two RF lightning protectors from the 7/16 female RF connectors (on top

of the main body) and store them in a safe location.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



8-3

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


...................................................................................................................................................................................................

2 Remove the defective RRH 2X60W:

• Unscrew the four bolts from the mounting bracket.

• Remove the RRH 2X60W from the mounting bracket.

...................................................................................................................................................................................................

3 Before sending the defective RRH 2X60W to the Repair Center, store the solar shield and

the RF lightning protectors, since these items will be reused for installation of the new

RRH 2X60W.

Note: Only the main body of the defective RRH 2X60W is to be sent to the Repair

Center.

...................................................................................................................................................................................................

4 Keep the existing cables and protect the connectors with caps near to the existing RRH to

be re-used if necessary.

...................................................................................................................................................................................................

5 Reinsert the new RRH 2X60W:

• Insert the two RF lightning protectors on the 7/16 female RF connectors (on top of the

main body).

• Hang the new RRH 2X60W on the mounting bracket.

• Screw the four M10 bolts to the mounting bracket.

• Connect all external cables to the RRH 2X60W.

Refer to chapter 6 in the document: Alcatel-Lucent Remote Radio Head 2X60 W -850, 1900MHz - Hardware Installation, 3MN-01477-0002-RJZZA

• Install the solar shield using the T25 TORX security drive.

...................................................................................................................................................................................................

6 Switch on the RRH 2X60, see the procedure “Powering up an RRH 2X60W” (p. 6-2).

...................................................................................................................................................................................................

7 Check with the WMS administrator that the RRH 2X60W is operational.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

E N D O F S T E P S...................................................................................................................................................................................................

7/17/2019 RRH.pdf


Appendix A: Product

conformance statements

Overview

Purpose

This appendix provides the RRH product conformance statements.

Contents

European regulatory requirement compliance A-2

Americas Region regulatory requirement compliance A-4

Federal Communications Commission A-5

Compliances for other regions/countries A-7

Operating conditions A-8

Cable specifications A-9

Product labeling A-10

...................................................................................................................................................................................................................................



A-1

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


European regulatory requirement compliance

Radio and Telecom Terminal Equipment

The RRH falls under the requirements of the Radio and Telecom Terminal Equipment

(R&TTE) European directive 1999/5/EC.The R&TTE directive covers requirements in the following areas:

• Protection of the Health and Safety of users and all other persons, including objectives

with respect to safety requirements contained in the Low Voltage Directive

(73/23/EEC)

Electromagnetic compatibility (EMC) protection requirements contained in Directive89/336/EEC.

This equipment generates, uses, and can radiate radio frequency energy. If notinstalled and used in accordance with the instruction manual, it can interfere withradio communications. However, there is no guarantee that interferences do not occur in a particular installation. If this equipment does cause harmful interference to radioor television reception, which can be determined by turning the equipment off and on.The user is encouraged to correct any interference problems. EMC requirements have been selected to ensure an adequate level of compatibility for apparatus in residential,commercial, and light industrial environments. Compatibility levels, however, do notcover extreme cases that can occur in any location, but that have a low probability of occurrence. In particular, they may not cover cases where a source of interference thatis producing repeated transient or continuous phenomena is permanently present. Thiscould include, for example, a radar or broadcast site in the near vicinity. In thesecases, it may be necessary to limit the source of interference, and/or apply special protection to the interfered part.

Note: For operation or maintenance inside Alcatel-Lucent systems, the operator must

always wear the antistatic wrist strap to maintain the integrity of the product.• Effective use of the Radio spectrum allocated to terrestrial/space radio communication

and orbital resources to avoid interference. The routes and standards used to

demonstrate compliance with these requirements are outlined in the following

paragraphs:

– Node B EMC

Compliance with essential EMC requirements was demonstrated using E301489-1& -23.

– Node B radio compliance

Compliance with the requirements of effective use of the radio spectrum was

demonstrated using E301908-1 & -3. – Node B safety

Compliance with essential safety requirements was demonstrated using EN60950.

– Node B health protection

Compliance with essential health requirements was demonstrated using E50385.

Product conformance statements European regulatory requirement compliance

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

A-2 Alcatel-Lucent – ProprietaryUse pursuant to applicable agreements



P

R E L I M I N A R Y

7/17/2019 RRH.pdf


European Union Environmental Directives (EUED)

The RRH is manufactured according to the following two European Union

Environmental Directives:

• Restriction of Hazardous Substances (RoHS), 2002/95/EC

The RoHS directive restricts the use of lead, mercury, cadmium, hexavalentchromium, poly-brominated biphenyls (PBB) and poly-brominated diphenyl ethers(PBDE) in electrical and electronic products. This directive applies to all electricaland electronic products placed on the European Union (EU) and European EconomicArea (EEA) markets after July 1, 2006, with certain exemptions, including anexemption for lead solder in network infrastructure equipment.

• Waste of Electrical and Electronic Equipment (WEEE), 2002/96/EC

The WEEE directive mandates the necessary treatment of such equipment when itenters end-of-life. It specifically identifies requirements for recycling, reuse, anddisposal.

Product conformance statements European regulatory requirement compliance

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



A-3

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Americas Region regulatory requirement compliance

United States

The statements that follow are the product conformance statements that apply to the

Alcatel-Lucent Remote Radio Head 2X60W when deployed in the Americas Region.

Product conformance statements Americas Region regulatory requirement compliance

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Federal Communications Commission

Federal Communications Commission

Important! Changes or modifications not expressly approved by Alcatel-Lucent, Inc.

could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

FCC Part 15 Class B

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

FCC Part 68

This equipment complies with Part 68 of the FCC rules and the requirements adopted by

the ACTA. At the upper-right-hand corner inside the cabinet assembly of this equipmentis a label that contains, among other information, a product identifier in the format of

AAAEQ##TXXXX. If requested, this number must be provided to the telephone

company.

FIC 04DU9-1SN.

Product conformance statements Federal Communications Commission

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



A-5

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


SOC 6.0N

The T1 network interface on this equipment is hardwired to a punchdown block, which

meets the FCC specifications.

If this equipment causes harm to the telephone network, the telephone company willnotify you in advance that temporary discontinuance of service may be required.

However, if advance notice is not practical, the telephone company will notify the

customer as soon as possible. Also, you will be advised of your right to file a complaint

with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the operation of the equipment. If this happens, the telephone

company will provide advance notice in order for you to make necessary modifications to

maintain uninterrupted service.

FCC regulations prohibit the connection of customer-provided equipment to central office

implemented systems. Connection to party lines is subject to tariffs; users should contact

their state public utility commission, public service commission, or corporation

commission for information.

If the equipment is causing harm to the telephone network, the telephone company may

request that you disconnect the equipment until the problem is resolved.

If trouble is experienced with this equipment repair or warranty information may be

obtained by contacting:

Technical Support Services, within the United States: +1 630 224 4762, prompt 2

RF approval

This equipment complies with Part 2, Subpart J - Equipment Authorization Procedures, of

the FCC Rules.

This device complies with Part 22 – Public Mobile Services, Subpart H – Cellular

Radiotelephone Services.

This equipment complies with Part 24 - Personal Communications Services, Subpart E -

Broadband PCS.

Product conformance statements Federal Communications Commission

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Compliances for other regions/countries

Compliances for other regions/countries

It is impossible to list all the applicable approvals/compliances as they depend on the

markets and products concerned.Note: For more information, contact your local Alcatel-Lucent representative.

Product conformance statements Compliances for other regions/countries

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



A-7

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Operating conditions

Operating conditions

The product compliance standards mentioned above are based on the following operating

conditions:• Doors must be closed and/or covers must be in place.

• External cables must be of the same type as specified by Alcatel-Lucent.

• The mechanical and electrical characteristics of the product must not be modified in

any way.

Any changes or modifications made to the product without written approval from

Alcatel-Lucent releases Alcatel-Lucent from responsibility regarding standards

compliance.

Product conformance statements Operating conditions

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Cable specifications

Cable specifications

Compliance with these standards was verified using cables as specified by

Alcatel-Lucent. The continued compliance of the product relies upon use of the correctcabling scheme as well as use of identical type cables as specified by Alcatel-Lucent.

Refer to the installation guides for details on cable specifications.

Product conformance statements Cable specifications

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



A-9

PRELI MI NA

RY

PRELI MI NARY

7/17/2019 RRH.pdf


Product labeling

Product labeling

The product label can be located on the inside or the outside of the product, provided that

the operation and/or maintenance personnel have the information when working on the product.

Node B labelling for European countries

To indicate compliance with the European R&TTE Directive, the RRH bears the

following label in a visible location:

• Manufacturers name

• Equipment designation

• Nominal voltage and maximum rated current

Labelling for other regions / countries

Labelling for other regions and countries is performed as appropriate and required by the

local regulatory framework.

Product conformance statements Product labeling

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................




P

R E L I M I N A R Y

7/17/2019 RRH.pdf


Index

B bulkhead, 5-2, 5-7

.............................................................

C connectors, 5-2, 5-7

procedure, 7-2

.............................................................

I inspecting

pole bands, 7-4

pole brackets, 7-4

.............................................................

M maintenance

preventive, 2-2

.............................................................

O orderable items, 3-2

.............................................................

P pole bands

inspecting, 7-4

pole brackets

inspecting, 7-4

powering down

RRH 2X60W, 6-4

powering up

RRH 2X60W, 6-2

preventive

maintenance, 2-2

procedure

connectors, 7-2

.............................................................

R replacement procedure, 3-2

replacing procedure

RRH 2X60W, 8-2

requirement, 5-11

.............................................................

S Safety statements, 1-1, 1-2

....................................................................................................................................................................................................................................



IN-1

PRELI M

I NARY

PRELI MI NARY

7/17/2019 RRH.pdf


Index

....................................................................................................................................................................................................................................

P

R E L I M I N A R Y

RRH.pdf

Documents

Transcript of RRH.pdf