A.B.N: 39 073 621 208PO Box 373, Hastings Vic 3915

Phone: 03 5978 8755 Fax: 03 5978 8016Email: info@roofextenda.com.auWebsite: www.roofextenda.com.au

Roof Extenda is Australian Owned & Designed

Roof Extenda PTY LTD is a family business founded in Melbourne in the mid 1990’s by Donald & Mary Dunkinson.

After retiring as a Master Builder, Don was restless and set to work in his backyard shed designing the original

‘Roof Extenda Bracket’.

RRoof Extenda is now led in a cooperative effort between second and third generation Dunkinson’s and has expanded beyond the family to provide jobs on the Mornington Peninsula.

Since then, the initial design has been refined to the MKII Bracket we distribute today, and is accompanied by the Shade Sail Anchor, S-Series and now the Safety Anchor.

Each of our products meetEach of our products meet Australian Standards and are Electroplated with Zinc.

We recommend regular upkeep when used in harsher environments such as coastal areas.

From backyard beginnings, Roof Extenda distributes its range

of products to Hardware stores Nationwide.

Product Guidewww.roofextenda.com.au

Designed & Made in Australia

The original and still the best

www.roofextenda.com.au

Four Installation Steps

• Remove roofing tiles or lift roof sheets to achieve an opening to fit the Roof Extenda bracket.

• Bolt angle bracket with the threaded rod to the selected rafter with 2 x M12 bolts. Secure the bracket to the top plate with 2-M10 coach screws through the two lower bottom holes

• Replace roof tiles or roof sheet, cutting a hole to allow the threaded rod to penetrate the roof.

• The Weather Seal is fitted to the top bracket, top bracket is then wound down to the desired height and the lock nut tightened. Mark the position of the Weather Seal on the roofing. Slide the Weather Seal up to apply clear neutral cure silicone to the area marked, press & shape the Weather Seal into the roof profile and finish with a bead of silicone to the edges of the Weather Seal to complete the fitting.

Unique steel brackets offering structurally superior fixing of extended roof-lines to buildings.

Easy to install through either tile or metal roofsNO special tools required.

Bolts attach brackets to rafter and top wall plate for extra strength and Bolts attach brackets to rafter and top wall plate for extra strength and

structural integrity.

Airflow between roof-lines provide improved ventilation in the summer heat.

Adjustability allows run off angles to be optimised and adds height for larger vehicles - 4WD’s, boats, caravans etc

New roof line is raised above the existing spouting therefore providing easy

access for cleaning and maintenance

Engineers computations request form available on our website.

MKII BracketThe Original

Our MKII Brackets are Zinc Electroplated.

When installed in coastal areas, we recommend regular upkeep with a

Cold Gal Spray.

Stocked in all Hardware stores Australia wideFind your local stockist on our website

Each MKII Bracket Package includes:

1 x Top Bracket1 x Bottom Bracket1 x Locking Hex Nut1 x FlashRite 1 x FlashRite Weather Seal

www.roofextenda.com.au

MKII BracketThe Original

The Roof Extenda’s ‘S Series’ Bracket is designed to provide “A Better Way” of attaching main beams for carports, pergolas, pool enclosures or any other roofing project that is to be added to the roofline. Roof Extenda’s ‘S-Series’ Bracket attaches to the rafter and the wall top plate therefore providing

strength, safety and peace-of-mind.

Roof Extenda’s ‘S-Series’ Bracket solves problems like height adjustments for carports etc.

AAvailable in three lengths: S300, S400 & S500.

Roof Extenda’s ‘S-Series’ Bracket can add height clearance to carports allowing for adequate overhead room for high vehicles and equipment. The Roof Extenda Bracket ‘S-Series’ is extremely successful in areas with high winds; it is fixed by coach bolts directly through the roof rafters and

coach screws into the wall top plate giving a structurally sound fixing method.

Four Installation Steps

• Remove roofing tiles or lift roof sheets to achieve an opening to fit the Roof Extenda bracket.

• Bolt angle bracket with the threaded rod & backing plate to the selected rafter with 2 or 4 x M12 bolts. Secure the bracket to the top plate with 2-M10 coach screws through the two lower bottom holes

• Replace roof tiles or roof sheet, cutting a hole to allow the threaded rod to penetrate the roof.

• The Weather Seal is fitted to the top bracket, top bracket is then wound down to the desired height and the lock nut tightened. Mark the position of the Weather Seal on the roofing. Slide the Weather Seal up to apply clear neutral cure silicone to the area marked, press & shape the Weather Seal into the roof profile and finish with a bead of silicone to the edges of the Weather Seal to complete the fitting.

www.roofextenda.com.au

S-SeriesThe

www.roofextenda.com.au

Special Order Available at all Hardware stores

Find your local stockist on our website

Each S-Series Bracket Package includes:

1 x Top Bracket1 x Bottom Bracket1 x Backing L-Plate1 x Locking Hex Nut1 x Locking Hex Nut1 x FlashRite Weather Seal

S-SeriesThe

Our S-Series Brackets are Zinc Electroplated.

When installed in coastal areas, we recommend regular upkeep with a

Cold Gal Spray.

www.roofextenda.com.au

WHAT IS YOUR LIFE WORTH?Safety is becoming more important and necessary in todays domestic

and commercial building processes.

Our fixed single point fall-arrest Safety Anchor, designed for use on timber roof trusses/rafters, has been tested for static and dynamic load capacity in accordance

with the new AS/NZS 5532-2013 STANDARDS.

For over 18 years Roof Extenda Pty Limited has been known for their second to For over 18 years Roof Extenda Pty Limited has been known for their second to none, superior products!

Four Installation Steps

• Remove roofing tiles or lift roof sheet to achieve an opening to fit the Roof Extenda Safety Anchor Bracket.

• Bolt angle bracket section and flat plate sandwiching the selected rafter at approx. 300 mm from the roof's ridge with a minimum of 8 x M12 Hex Bolts, Nuts and Nuts and Washers (Not supplied).

• Replace roof tiles or roof sheet, cutting a hole to allow the loop & rod to penetrate the roof.

• Slide Weather Seal over the loop and down the shaft. Ensuring roofing area is clean and dry, mark the position of the Weather Seal on the roofing. Apply clear neutral cure silicone to the area marked, press and shape the Weather Seal into the roof profile, finish with a bead of silicone to all edges of the the Weather Seal to complete the fitting.

Safety AnchorThe all NEW

www.roofextenda.com.au

Special Order Available at all Hardware stores

Find your local stockist on our website

Each Safety AnchorPackage includes:

1 x Safety Anchor Bracket1 x Backing Plate1 x FlashRite Weather Seal

Safety AnchorThe all NEW

Our Safety Anchors are Zinc Electroplated.

When installed in coastal areas, we recommend regular upkeep with a

Cold Gal Spray.

www.roofextenda.com.au

Four Installation Steps

• Remove roofing tiles or lift roof sheet to achieve an opening to fit the Roof Extenda Shade Sail Anchor Bracket.

• Bolt the section with steel rod and the backing plate to the rafter using 4 x M12 bolts. Secure both brackets to the top plate with 2-M10 coach screws to each bracket.

• Replace roof tiles or roof sheet, cutting a hole to allow the loop & rod to penetrate the roof.

• Slide Weather Seal over the loop and down the shaft. Ensuring roofing area is clean and dry, mark the position of the Weather Seal on the roofing. Apply clear neutral cure silicone to the area marked, press and shape the Weather Seal into the roof profile, finish with a bead of silicone to all edges of the the Weather Seal to complete the fitting.

Please Note: Roof Extenda can only provide kN strength.We’re unable to provide engineer computations or guarantees on this installation of this product.

We advise you carefully evaluate; Shade Sail Size, Location, Wind Category & Installation design before purchasing.

A better way of attaching Shade Sails to buildings

Shade Sails are being erected all over the World

Their popularity is increasing as they offer many forms of protection from inclement weather; over barbecues, play areas, outdoor pools and spas. The Roof Extenda Shade Sail Anchor is designed to solve problems and provide a better & safer means of attaching Shade Sails to buildings.

The Shade Sail Anchor is bolted directly to the rafter and wall top plate of the existing building, giving a structually sound fixing method, ensuring the

strongest means of support. This innovative design, greatly reduces the time and effort compared to

traditional Shade Sail fixings

Shade Sail AnchorThe

www.roofextenda.com.au

Each Shade Sail AnchorPackage includes:

1 x Shade Sail Bracket1 x Backing L-Plate1 x FlashRite Weather Seal

Shade Sail AnchorThe

Stocked in all Hardware stores Australia wideFind your local stockist on our website

Our Shade Sail Anchors are Zinc Electroplated.

When installed in coastal areas, we recommend regular upkeep with a

Cold Gal Spray.

www.roofextenda.com.au

Available for Special Order with your local Stockist

Flexatile - Lead Free Base Size - 450 x 280mm -Available in Black or Terracotta -Paint to match roof colour with acrylic house paint -Light weight, non toxic, non corrosive -Drinking water safe -Polymer is Ozone and UV resistant -Bushfire Attack Level (BAL): [Cone 12.5] [Sheet 29]

Six Installation Steps

• Cut the rubber cone at least 15mm smaller than Pipe O.D. with a knife.• Place ‘Double sided gluded foam tape’ on the underside of the base.• Lubricate pipe with water and slide the flashing down the pipe.• Form an anti-capillary fold top of base sheet.•• Hand form the base all around the tile and apply pressure to the adhesive strip and foam.• Apply sealant along edges.

FlexatileWeather Seals

www.roofextenda.com.au

Stocked in all hardware stores Australia wideFind all of our stockist on our website

Supplied with all our brackets as the default choice. The FlashRite Weather seals by Aquarius Distribution are a versatile Flashing for

all roofing materials*.

Specially designed for retrofit and repair application, you won’t need to remove the bracket or deconstruct, should a repair be required

*extra care may be required to ensure a water-tight seal

For more information, see For more information, see www.aquariusdist.com.au

FlashRite - Aquaseal Base Size - 163 x 163mm Black - Standard seal supplied within all packages. - Bushfire Attack Level (BAL): 12.5 Red - Special order required - Bushfire Attack Level (BAL): 19

FlashriteWeather Seals

www.roofextenda.com.au

Please find our Engineering Computation Request form on our website.

Not every single installation is the same.Different timber, wind categories, and pergola sizes can drastically change

the requirements of our Pergola Brackets.

That’s why Roof Extenda can provide an engineering computation calculation for your

MkII & S-Series bracket installation.

YYou can find a request form on our website atwww.roofextenda.com.au

We require that the form is completed in full before we can provide any calculations for your installation.

This calculation can also ensure you’re using enough brackets, spaced at an appropriate distance for your project.

Due to the nature of the bracket design, the bracket computation takes into Due to the nature of the bracket design, the bracket computation takes into account lateral and dynamic loading.

Please note, we can ONLY provide calculations for the MkII & S-Series Brackets being installed on existing Timber Frames.

For Shade Sail Anchors: Be advised that the Shade Sail Anchor has been strength tested.

When bolted in the top holes, the Anchor can deform at 2.3 kN of force.When bolted in the middle holes, the anchor can deform at 1.3 kN of force.When bolted in the middle holes, the anchor can deform at 1.3 kN of force.

We advise you carefully evaluate; Shade Sail size, Location, Wind Category & Installation Design before purchasing.

EngineeringRoof Extenda

www.roofextenda.com.au

For more information on the electroplating processvisit Excellent Plating Works’ website

www.epw.com.au

Roof Extenda works with our manufacturers and Excellent Plating Works Pty Ltd to ensure all of our products are

Electroplated with Zinc to protect the brackets from the elements and meet the Australian Standards – AS/NZS/ISO 9001:2000

The Zinc plating is applied by immersing our brackets in a Zinc Salt The Zinc plating is applied by immersing our brackets in a Zinc Salt Solution, and applying an electrical current through the bath.

This applies a layer of pure Zinctha at 8 - 12 Microns thick, without hampering the installation of our brackets

While we have tested the durability of the brackets with the Zinc Coating, While we have tested the durability of the brackets with the Zinc Coating, Roof Extenda cannot provide any guarantees on the lifetime of the

coating, and recommend checking the brackets annually.

If installing any of the Roof Extenda brackets in highly corrosive areas, If installing any of the Roof Extenda brackets in highly corrosive areas, we highly recommend that home owners keep the brackets protected

with a Galvanized Paint.

Cold Galvanized Paints can be found at most hardware stores and can easily be applied to the exposed surfaces of the brackets

for added protection.

Zinc ElectroplatingRoof Extenda