roduct Data - Westox€¦ · Clean up all equiprnent infresh utater immediately q.fier use....
1
roduct Data Colours White, Grey, Magnolia Refer to colour chart (or made to order) Volume Solids 55/o !1o/o Specific Gravity 1.25 t.O5 Elongation to Bfeak In excess of 2OO"/" Flash Point Finish @ 25 celsius unreinforced Not applicable Satin ChemicalResistance Resists mild chemical environments Full CSIRO & NATA Test Reports Available on Request. GENERAL Do not apply coatings if temperature is belout 15"c or ouer J0"c. (Loto Temp Grade 0-30D Do not apply coating if rain is intminent. Not recommendedfor belout grade waterproofing or uthere water pressure is from uithin the toall. PREPARATION The surface to be treated should be dry clean sound and free from oil, grease, Jlaking paint and laitence and other deleterious materials. Sound paint may be ouercoated. Neu concrete should be minimum 28 days old before application co mlnences. All cracks or holes exceeding 2mm are to be repaired before a.pplication commences. APPLICATION / SPECIFICATION Apply one coat of the appropriate Westox Primer. Apply by brush, roller or q.irless spray to the prepared surface offer by the manufacturer, nor does the manufacturer warrant or guarantee its accuracy or completeness in describing the performance or suitability of the various products. VERTICAL SURFACES Apply one coat at the rate of 4m') per litre and, allau to dty. Apply second coat at the rq.te of 4m' per litre W.F.T. approximately 250 microns. Finished dry film thickness (D.F.T.) should then be approxiruately 275 microns. (Total D.F.T. should neuer be less than 250 microns). HORIZONTAI, SURFACES Apply first coat to pri?ned surface at the approximate rate of 2m' per litre and whilst still utet roll out reinforcing mesh and embed, utorking uith a brush to ensure complete saturation of fabric. Allou minimum 8 hours before application of second coat of membrq.ne at the rate of 2m' per litre and allow 24 hours to dry. Apply third coat of membrane at the rate of 2m' per litre at right angles to preuious coats. Thoroughly check surface after 24 hours to ensure that complete couerage has been attained and no pinholing is euident. Surface uill be touch tuy in t hours, and tttill acceptfoot traffic afier 18 hours. Will achieue full cure taithin 7 days. Auoid utater ponding.for first J days after o.pplication. SAFETY - Not classified as dangerous goods Refer to Westlegate Pty Limitecl Material Safety Data Shee I fo r i nstr u ctio ns. CLEANUP Clean up all equiprnent infresh utater immediately q.fier use. PACKAGING Container Sizes -15 litre containers. Shetf Life Veight Transport -12 months in unopened containers. - 1.25kg per litre = 1 8.75kg per I 5 litre. - No special transport requirements. APPRovED APPLICAToR: WESTOX pRODI ICTS Westlegate Pty Ltd 16 Frost Road, Campbelltown NSW 2560 Ph:02 4628 5010 Fax: 0246285020 w Quality Endorsed Company ISO 900112000 LlC6553
Transcript of roduct Data - Westox€¦ · Clean up all equiprnent infresh utater immediately q.fier use....
roduct Data
Colours White, Grey, MagnoliaRefer to colour chart(or made to order)
Volume Solids 55/o !1o/o
Specific Gravity 1.25 t.O5
Elongation to Bfeak In excess of 2OO"/"
Flash Point
Finish
@ 25 celsius unreinforced
Not applicable
Satin
ChemicalResistance Resists mild chemicalenvironments
Full CSIRO & NATA Test Reports Available on Request.
GENERAL
Do not apply coatings if temperature is belout 15"c or
ouer J0"c. (Loto Temp Grade 0-30D
Do not apply coating if rain is intminent.
Not recommendedfor belout grade waterproofing or
uthere water pressure is from uithin the toall.
PREPARATION
The surface to be treated should be dry clean sound
and free from oil, grease, Jlaking paint and laitence
and other deleterious materials.
Sound paint may be ouercoated.
Neu concrete should be minimum 28 days old before
application co mlnences.
All cracks or holes exceeding 2mm are to be repaired
before a.pplication commences.
APPLICATION / SPECIFICATION
Apply one coat of the appropriate Westox Primer.
Apply by brush, roller or q.irless spray to the
prepared surface
offer by the manufacturer, nor does the manufacturer warrant or guarantee its accuracy or completeness in describing the performance or suitability of the various products.
VERTICAL SURFACES
Apply one coat at the rate of 4m') per litre and, allau to dty.
Apply second coat at the rq.te of 4m' per litre W.F.T.
approximately 250 microns. Finished dry film thickness
(D.F.T.) should then be approxiruately 275 microns.
(Total D.F.T. should neuer be less than 250 microns).
HORIZONTAI, SURFACES
Apply first coat to pri?ned surface at the approximate
rate of 2m' per litre and whilst still utet roll out
reinforcing mesh and embed, utorking uith a brush to
ensure complete saturation of fabric.Allou minimum 8 hours before application of second
coat of membrq.ne at the rate of 2m' per litre and allow
24 hours to dry. Apply third coat of membrane at the
rate of 2m' per litre at right angles to preuious coats.
Thoroughly check surface after 24 hours to ensure that
complete couerage has been attained and no pinholing
is euident. Surface uill be touch tuy in
t hours, and tttill acceptfoot traffic afier 18 hours.
Will achieue full cure taithin 7 days.
Auoid utater ponding.for first J days after o.pplication.
SAFETY - Not classified as dangerous goods
Refer to Westlegate Pty Limitecl Material Safety Data
Shee I fo r i nstr u ctio ns.
CLEANUP
Clean up all equiprnent infresh utater immediately q.fier use.
PACKAGING
Container Sizes -15 litre containers.
Shetf Life
Veight
Transport
-12 months in unopened containers.
- 1.25kg per litre = 1 8.75kg per I 5 litre.
- No special transport requirements.
APPRovED APPLICAToR: WESTOX pRODI ICTSWestlegate Pty Ltd
16 Frost Road, Campbelltown NSW 2560Ph:02 4628 5010 Fax: 0246285020
wQuality
EndorsedCompany
ISO 900112000 LlC6553
