1

JJC RM-E4 Infrared Remote Control Instruction

Thank you for purchasing JJC RM-E4 Infrared Remote Control.

For the best performance, please read this instruction carefully before use.

� To use RM-E4 Remote Control

1. For the first time use, please pull out the plastic separator (if your remote control has it) at the

battery holder.

2. Mount the camera on a tripod (recommended) or place the camera on a stable, level surface.

3. Press the button and rotate main command dial until (delayed remote) or (quick response

remote) is displayed in the control panel.

4. Aim the transmitter on the remote control at the infrared receiver on the camera (usually within

+/- 20 degree of the lens axis, from the left to the right and from the top to the bottom) and

press the shutter-release button on the remote control (when using the remote outdoors, make

sure that the subject is not backlit and that the line of site between the transmitter and the

infrared receiver is not blocked by the lens or other obstacles).

5. How the camera focuses and shoots depends on the option selected for your camera's custom

setting. For further information, check your camera's manual.

Infrared cannot be seen by human eyes. So you will see no visible light from the LED on the

front end of the remote control when operating.

2

� Identifying the buttons

T/W button is for change Pentax camera’s lens ZOOM. P

Part S button is for shutter.

(T/W function is not working on Pentax DSLR/SLR camere.)

N

Part S button for Nikon camera Shutter

S button for Canon DSLR/SLR camera instant shutter. C1

Part 2S button for 2seconds delay shutter.

S button for Canon PowerShot cameras shutter.

T side for telephoto

W side for wide-angel

Move Backword (replay mode)

Move forward (replay mode)

Toggle various onscreen data overlays

Thumbnail index / zoom out

C2

Part

Play magnification

controls zoom, image display, and toggle displays

� Specification

• 100% compatible with Pentax Remote E infrared remote controls.

• Works with all remote shutter release control modes (Quick-response, W/T Zoom).

• Easy-to-replace CR2025 lithium battery.

• Operating temperature: 5 °C to 40 °C (40 °F to 105 °F).

• Typical Battery Life: up to 3 years, 20,000 exposures.

3

� To Replace the Battery

1. The remote control is powered by a three-volt CR2032 lithium battery which is already

included in.

2. After sliding the latch in the direction shown to unlatch the battery holder, remove the

holder.

3. Remove the battery from the battery holder.

4. Insert a fresh battery with the face marked "+" on top.

5. Slide the battery holder into the remote until the latch clicks into place.

� Attention:

a. When the remote control is not in use over a long time, please remove the

battery from the remote control.

b. Do not leave the remote control in places subject to extremely high

temperatures.

Pentax Part compatible with Pentax Cameras （（（（P part））））

Digital SLR K110D K100D K10D *ist DL

*ist DS *ist D *ist DS2 *ist DL2

Optio S S4 S4i S5i

S5n S6 S7 430

450 550 750z S50

S40 SV 330 A10

A20 A30

Film SLR *ist MZ6 MZ-L ZX-L

Pentax Part compatible with Samsung Cameras （（（（P part））））

Digital SLR GX-1L GX-1S GX-10

Canon DSLR/SLR part compatible with Canon Cameras （（（（C1 part））））

Digital SLR 400D 350D 300D Digital Rebel

Digital Rebel XT Digital Rebel XTi

Film SLR ELAN 10 30 33

50 55 100 300v

300x 3000v QD Rebel K2 Rebel T1 Date

Reble T2 Date Kiss III Kiss III L A10

APS SLR EOX IX

SureShot

(Prima

Super)

Z180U Z155 120

ELPH 370Z Z3

4

Canon DC part compatible with Canon Cameras （（（（C2 part））））

Power Shot Pro 1 G6 G5 G3

G2 G1 S1 IS S70*

S60* Pro 90 IS

*Only work with shutter function.

Nikon part compatible with Nikon Cameras （（（（N part））））

Digital SLR D80 D70s D70 D50

D40 D40x

Film SLR F65 F75 N65 N75

Coolpix 8800 8400

LiteTouch 150ED 140ED 130ED 110S

100W

Nuvis Nuvis S

Copyright of JJC Technology Company