REV900 ASSEMBLY EN
3
5B 5A Frame Column Short feet End pipe U shape end pipe Outer pipe Connection pipe Cable clamp Rubber grip Rubber washer Hole cap Control Box / Hand control Hand control AC cable Motor extension cable Screws Screw for motor house / Outer pipe, M6x16mm Screw for feet, M10x16mm Screw for tabletop, Ø5x20mm PACKING LIST pcs 1 1 1 1 2 2 4 2 9 2 pcs 1 1 1 pcs 4 4 9 Maximum 6Nm Maximum 10Nm Maximum 10Nm < 6Nm Tightening torque Tailstock Screw for motor house and outer pipe Screw for feet and tabletop Screw for hand control Make sure all screws are tightened, also after a period of use! WARNING Carefully arrange all the cables not to be damaged by tabletop screws. Reset the desk before use Press both up and down buttons at the same time for 3 seconds. Continue pressing the buttons until both columns are in lowest position. When finish reset, the control box makes a sound and the buttons can be released. Now the system is operational. Step 1 Step 2 Step 4 Step 3 Step 5 REV900 - ASSEMBLY MANUAL 1 www.rev-247.com | 800.743.7738
Transcript of REV900 ASSEMBLY EN
5B
5A
Frame ColumnShort feetEnd pipeU shape end pipeOuter pipeConnection pipeCable clampRubber gripRubber washerHole capControl Box / Hand control Hand controlAC cableMotor extension cableScrewsScrew for motor house / Outer pipe, M6x16mmScrew for feet, M10x16mmScrew for tabletop, Ø5x20mm
PACKING LISTpcs1111224292pcs111pcs449
Maximum 6NmMaximum 10NmMaximum 10Nm< 6Nm
Tightening torque TailstockScrew for motor house and outer pipeScrew for feet and tabletopScrew for hand controlMake sure all screws are tightened, also after a period of use!
WARNINGCarefully arrange all the cables not to be damaged by tabletop screws.
Reset the desk before usePress both up and down buttons at the same time for 3 seconds. Continue pressing the buttons until both columns are in lowest position. When finish reset, the control box makes a sound and the buttons can be released. Now the system is operational.
Step 1
Step 2
Step 4
Step 3
Step 5
REV900 - ASSEMBLY MANUAL
1www.rev-247.com | 800.743.7738
Frame ColumnLong feetEnd pipeOuter pipeConnection pipeCable clampRubber gripRubber washerHole capControl box / Hand control Control boxScrewsScrew for motor house / Outer pipe, M6x16mmScrew for feet, M10x16mmTailstock for connection pipe, M10x20mmScrew for tabletop, Ø5x20mmScrew for hand control, Ø4x22mm
PACKING LISTpcs2224284164pcs1pcs888142
Maximum 6NmMaximum 10NmMaximum 10Nm< 6Nm
Tightening torque TailstockScrew for motor house and outer pipeScrew for feet and tabletopScrew for hand controlMake sure all screws are tightened, also after a period of use!
WARNINGCarefully arrange all the cables not to be damaged by tabletop screws.
Reset the desk before usePress both up and down buttons at the same time for 3 seconds. Continue pressing the buttons until both columns are in lowest position. When finish reset, the control box makes a sound and the buttons can be released. Now the system is operational.
Step 3
Step 4
Step 1 Step 2
2www.rev-247.com | 800.743.7738
x12
x23 x2
Step 8
Step 9
Step 10
Step 5
Step 6
Step 7
x8
3
Adjust frame
length Adjust frame length
www.rev-247.com | 800.743.7738
