R-PILOT Brochure Cover Page
5
Transcript of R-PILOT Brochure Cover Page
1
1
2
2
3
3
4
4
A A
B B
TITLE
ASSEMBLY, 1-2 R-P-PILOT PRESSURE SENSOR
SCALE
DWG NOSM-010 FIGURE 1
REV0
SHEET 1 OF 2 DRAWING NOT TO SCALEHOUMA, LA
PARTS LISTDESCRIPTIONQTYITEM
Body11Ajustment Bolt12Locknut13Panel Nut14Spring Guide15Spool16Peek Insert27Sensing Base18Sensing Piston19Sensing Sleeve110O-ring111*O-ring112O-ring Back-up113O-ring314Spring115
OVERVIEW / OPERATIONTHE BWB "R-PILOT" IS A 3 WAY, NORMALLY CLOSED OR NORMALLY OPEN, AUTOMATIC, PRESSURE SENSING DEVICE. BY CHOOSING THE APPROPRIATE INLET, THE SENSOR CAN DETECT PRESSURE ABOVE (PSH) OR BELOW (PSL) ANY DESIRED PRESSURE SETTING. BY SELECTING THE CORRECT PISTON & SPRING COMBINATION (SEE PRESSURE CHART), AND EITHER LOOSENING OR TIGHTENING THE ADJUSTMENT CAP, THE SENSOR MAY BE SET BETWEEN 3 AND 10,000 PSI. IT IS NORMALLY INSTALLED ON A PROCESS VESSEL, PROCESSFLOW LINE, OR IN A CONTROL PANEL. THE SENSOR RECEIVES SENSING PRESSURE (PORT P) FROM THE COMPONENT WHICH IT IS MONITORING AND SUPPLY PRESSURE (PORT A OR B) FROM THE SAFETY SYSTEM WHICH IT WILL SHUT DOWN. FEATURES• DEADBAND +/- 5% OF SET PRESSURE (DEADBAND MAY BE AFFECTED IN HYDRAULIC APPLICATIONS)• SET POINT REPEATABILITY 1% OF SET PRESSURE• EXOTIC MATERIAL AVAILABLE UPON REQUEST• VITON SEALS STANDARD• OTHER ELASTOMERS AVAILABLE UPON REQUEST• WEIGHT : 4 LBS.
LOW HI
OU
T
CONNECTIONS:PORT APSH SUPPLY PRESSURE INLETPSL EXHAUST30 - 150 PSI (2.06 - 10.3 bar) PORT BPSL SUPPLY PRESSURE INLETPSH EXHAUST30 - 150 PSI (2.06 - 10.3 bar) PORT CSUPPLY PRESSURE OUTLET30 - 150 PSI (2.06 - 10.3 bar) PORT PSENSING PRESSURE INLET10 -10,000 PSI (0.7 - 689.48 bar)
SENSIN
G PRESSU
REIN
LET
NOTE: (*) SEE PISTON / SPRING CHARTS FOR SPECIFIC PISTON AND ORING CONFIGURATIONS. REPAIR KITS CONTAIN ALL SEALS TO FIT ANY PISTON CONFIGURATION.
2314155
6 14
911*108
12 13 7
B A
C
P
1/4-18 NPT
1
1
2
2
3
3
4
4
A A
B B
TITLE
ASSEMBLY, DIMENSIONS, R-PILOT
SCALE
DWG NOSM-010 FIGURE 2
REV0
SHEET 1 OF 1 DRAWING NOT TO SCALEHOUMA, LA
10.937277.8 mm
MAX
3.31184.1 mm
.75019.1 mm
7.686195.2 mm
3.68693.6 mm
1/2-14 NPT
1" WRENCH FLAT25.4 mm
1/4-18 NPTTYPICAL 3 1 1/4" WRENCH FLAT
31.75 mm
1-3/8" PANEL HOLE34.93 mm
1.62541.3 mm
HEX PANEL NUT
2.00
050
.8 m
m
.870 WRENCH FLAT22.1 mm
1
1
2
2
3
3
4
4
A A
B B
TITLE
SENSING ASSEMBLIES, R PRESSURE SENSOR
SCALE
DWG NOSM-010 FIGURE 3
REV0
SHEET 1 OF 2 DRAWING NOT TO SCALEHOUMA, LA
NOTE:BWB CONTROLS "R" PRESSURE SENSORS CAN BE CONFIGURED TO MEET THE CUSTOMERS NEEDS BY SELECTING THE APPROPRIATE PISTON AND SPRING COMBINATION. PLEASE REVIEW THE CHARTS LISTED BELOW TO DETERMINE WHICH CONFIGURATION IS REQUIRED. **NEVER INSTALL MORE THAN ONE ORING ON THE SENSING PISTONS AT ONE TIME.
#1/2 PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)PLAIN 3 - 10 .21 - .69RED 15 - 50 1.02 - 3.45
GREEN 50 - 200 3.45 - 13YELLOW 150 - 325 10 - 22
#2/1 PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)GREEN 150 - 500 10 - 34
YELLOW 300 - 900 20 - 62
#2/3 PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)GREEN 150 - 500 10 - 34
YELLOW 300 - 900 20 - 62
#3/2 PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)
GREEN 500 -1,500 34 - 103YELLOW 750 - 2,000 52 - 138
#4/5 PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)
GREEN 1,000 - 3,000 69 - 207YELLOW 1,500 - 4,000 103 - 275
#5/4 PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)GREEN 2,000 - 6,000 138 - 413
YELLOW 3,500 - 10,000 241 - 690
1
1
2
2
3
3
4
4
A A
B B
TITLE
SENSING ASSEMBLIES, R PRESSURE SENSOR
SCALE
DWG NOSM-010 FIGURE 3
REV0
SHEET 2 OF 2 DRAWING NOT TO SCALEHOUMA, LA
RLP PISTON CONFIGURATIONSPRING RANGE (PSI) RANGE (BAR)
PLAIN 3 - 10 .21 - .69
