Quick Start Guide

Version: 1.0

Date: Nov. 2018

ProRF

Overview

1

LED indicator

Reset Button

Name Description

LED indicator

� Green flashes once in a second: verifying, enrollment or deletion status.

� Green glows continuously for 2 seconds: Authentication success

� Red glows continuously for 2 seconds: Authentication failure

Reset � Reboot the device: press the reset button and hold it for 3 seconds.

Magnetic Tamper

Switch

� Restore factory setting

� Tamper Switch: keep the magnetic tamper switch on back plate, or it will

trigger the tamper alarm.

Magnetic tamper

switch

Cables and connectors

48

5B

48

5A

GN

DT

XD

RX

DG

ND

Wd

1

BE

EP

GL

ED

RL

ED

1W

D1

1W

D0

GN

D

12

VO

UT

GN

D

Wd

0

+1

2V

RJ4

5-6

RJ4

5-3

RJ4

5-2

RJ4

5-1

AU

X

BE

L-

BE

LL

+

GN

D

BU

TN

OC

OM

NC

AL

-

SE

N

AL

+

GN

D

Input: DC12V 3A

Operating Temperature: 20 ~65℃ ℃

Waterproof: IP65

Made in China

2

DESCRIPTION WIRE

RJ45 6-

RJ45 3-

RJ45 2-

RJ45 1-

AUX

GND

BELL-

BELL+

SEN Yellow

Black

Brown

Green

Orange

Blue

PIN

A1

A2

A3

A4

B1

B2

B3

B4

B5

B6

B7

GND

BUT

Black

Orange+White

Green White+

Green White+

Orange+White

NO

COM

NC

AL-

AL+

485B

485A

GND

TXD

Yellow

White

Gray

Black

Pur lep

Green

Orange

Blue

B8

B9

B10

B11

B12

C1

C2

C3

C4

C5

C6

RXD

GND Black

Gray

Pur lep

WD1

WD0

WhiteC7

C8 Green

DESCRIPTION WIRE

BEEP

GLED

RLED

IWD1

IWD0

GND

12VOUT

Gray

Black

Pur lep

Green

Blue

PIN

D1

D2

D3

D4

D5

D6

D7

E1

E2

GND

+12V

Black

White

Red

Red

1 42 3

A B

1 42 3 5 6 7 8

C D E

10 11 121 42 3 5 6 7 8 9

1 42 3 5 6 7 1 2

3

Installation

①

②

1) Paste the mounting template

sticker on the wall, and drill holes

according to the mounting paper.

2) Fix the back plate on the wall using

wall mounting screws.

3) Attach the device to the back plate. 4) Fix the device to the back plate

with a security screw.

4

Power Connection

12V AdaptorDC

Recommended power supply

1)12V ± 10%, at least 500mA.

2)To share the power with other devices, use a power supply with higher current ratings.

E2

E1GND

+12V DC

E2

E1GND

+12V DC

5

Ethernet Connection

Ethernet Cable

Network Cable Adaptor

1) The device connects to the computer over an Ethernet through a switch.

2) The device directly connects to the computer.

876

RJ 45 54321

Default IP address: 192.168.1.201

Subnet mask: 255.255.255.0

Ethernet Cable

Lock Relay Connection

6

Device not sharing power with the lock

The system supports Normally Opened Lock and Normally Closed Lock.

T Normally Closed Lock below:ake as an example

Normally Closed Lock

+12VDC

GND

! Maximum 30V 2A input.

NC

COM

FR107 Diode

-+

B10

B9

7

Lock Relay Connection

Device sharing power with the lock

Normally Closed Lock+12VDC

! Maximum 12V 2A input.

FR107 Diode

-+

NC

GND

COM

B10

B6

B9

E2

Notes:

1.The system supp The NO LOCK (normallyorts Normally Opened Lock and Normally Closed Lock.

opened at power on) is connected with ‘NO’ and ‘COM’ terminals, and the NC LOCK (normally closed at

power on) is connected with ‘NC’ and ‘COM’ terminals.

2. When electrical lock is connected to the Access Control System, you must add one FR107 diode in

parallel equipped in the package) to prevent the self-inductance EMF from affecting the system.(

Door Sensor, Exit Button, Bell & Alarm Connection

8

Door Sensor

SEN

GND

BUT

GNDB6

B5

B6

B7

Bell+-

GND +12V

B4

B3BELL-

BELL+

Alarm

Alarm's power switch

- ++-

B12

B11AL-

AL+

Exit Button

R 232 CS onnection(optional)R 232 CS onnection(optional)

9

Rs232 CableSerial Printer

C5

C4

C6

TXD

RXD

GND

RS485 Connection

C1

C2485B

485A

RS485 Reader

C3GND

Power supply

Lock

+

+-

-

C8

E1GND

E2

C7W 0D

W 1D

Wiegand Output Connection

Security Relay Box

10

After a successful verification, the device will send Wiegand signals to the SRB access controller,

then the SRB will output relay signals to trigger the relay to unlock the door.

+12V12V

W 0D

W 1D

COM

NC

GND

GNDNO

BUT

D5

E1GND

E2

D4I 0WD

I 1WD

+12V

Wiegand Reader

Wiegand Input Connection

Exit Button

Alarm

Doorbell

Smokedetector

11

Lock TCP/IP

Exit Button

Door Sensor

Card Reader

Standalone Installation

Quick Start Operations

12

Suppose the device is connected with PC and the software (ZKBiosecuty 3.1.5.0) is installed.

Double-click the ZKBiosecuty icon on the desktop to open.

Click [Access Device] > [Device] > [New], enter device

name and IP Address of the device and click [OK]. The

following interface will be shown:

Add Device

13

Add Personnel1. Click [Personnel] > [Personnel] > [New] to add persennel information and set access levels .

Note:

1. IP addresses of the server (PC) and the device must be in the same network segment. The

default IP Address of the device is 192.168.1.201.

2. Please set the device type to standalone device.

3. Once IP address and communication password missing, please refer Reset function.

14

Sync All Data to Device

The system will synchronize the data to the device, including door information, access control

levels (personnel information, access control time zones), and so on. Select device, click

[Synchronize All Data to devices] and click [OK] to complete synchronization.

User can set Access Control Time Zones, Access Control Holiday, Door Settings, Access Levels,

Personnel Access Levels and so on in Access Control interface. For more details, please refer

the user manual and the software instruction.

Access Control Setting

Forgot the password/IP address?

Trigger the magnetic tamper switch three times quickly

within 30-60 seconds of the device start-up. (After

operation successfully, beep sound continue and

device reboot automatically.)

This process restores factory settings, such as device

password, IP address, etc.

Tips

www.zkteco.eu

© . . .Copyright 2018 ZKTeco Inc ZKTeco Logo is a registered trademark of ZKTeco or a related company All other product and company names mentioned are used for

. . .identification purposes only and may be the trademarks of their respective owners All specifications are subject to change without notice All rights reserved