EC10 & EX16 Quick Start Guide

Button-controlled

EC10Technical Specification

3.Technical Specifications

5.Appearance of case

RS485

TCP/ IP or RS485

Wiegand/RS485

EC10 Elevator Control Panel

EX-16 Floor Expansion Board

Version:V1.1 Date：2013.7

18#Output

17#Output

16#Output

15#Output

14#Output

13#Output

12#Output

11#Output

DC 12V

26#Output

25#Output

24#Output

22#Output

21#Output

20#Output

19#Output

23#Output

12VOutput

RS485

NCCOMNO

NCCOMNO

NCCOMNO

NCCOMNO

NCCOMNO

NCCOMNO

NCCOMNO

NCCOMNO

GNDSTAT

+12VGND

AUXOUT8 AUXOUT16

AUXOUT7 AUXOUT15

AUXOUT6 AUXOUT14

AUXOUT5 AUXOUT13

AUXOUT4 AUXOUT12

AUXOUT3 AUXOUT11

AUXOUT2 AUXOUT10

AUXOUT1

I N D

POWER

EXT

NOCOMNC

NOCOMNC

NOCOMNC

NOCOMNC

NOCOMNC

NOCOMNC

NOCOMNC

NOCOMNC

+12VGND

485-485+

OR

Fingerprint

Reader

RFID Reader

Elevator Floor Buttons

EX16Technical Specification

Floor button control relays:10Card capacity: 30,000Fingerprint capacity: 3,000Event capacity: 100,000Power supply: 12V DC 1ACommunication: TCP/IP, Rs485Supported floor expansion board: 3pcs

Floor button control relays:16Communication to EC10 panel: RS485Power supply: 12V DC 1A

Elevator Control Extension Board Power Supply

p

q

RS-485 EXT WIEGAND 3 IN5 IN6 OUT5 OUT6 WIEGAND 4 IN7 IN8 OUT7 OUT8131312121101313121211016

WIEGAND 1 IN1 IN2 OUT1 OUT2 WIEGAND 2 IN3 IN4 OUT3 OUT41 3

POWER1 5 1 10 1 2 1 2 1 3 1 3 1 10 1 2 1 2 1 3

Reset

Power SupplyController Panel

Heat dissipation hole

Key hole

Threading hole

EX-16

7. EX16 Elevator Wiring Diagram

The EC10 prevents unauthorized elevator-users from accessing pre-defined restricted floors in

the building. The EC10 (Elevator Control panel) controls access up to 10 floors. Also available is

the EX16 (Elevator Floor Expansion board) which allows for access control of up to 16 additional

floors. A maximum three EX16 boards can be daisy-chained together and collectively control

access of up to 58 floors. In order to gain access to a desired floor, authorized users must first

present either a valid fingerprint and/or RFID card when entering the elevator. For example, if an

authorized user has access rights to only floor and floor , the elevator will not move if that

same user presses the elevator button for floor .

3

4

10

2.System Introductions

1. Installation Precautions

Button-controlled

Pay attention to the following safety items. Mis-operations may cause human danger or

equipment faults:

1)Before installation completes, do not power on the equipment or perform operations

with electricity.

2) Use dedicated elevator ethernet cable to connect the elevator controller and computer.

Use 2pin controller cable for the press button on each floor.

3) Install the card reader with a height of 1.2 to 1.4 meters.

4) Install the elevator main controller and expansion board on the elevator lift car.

5) Install the emergency button in the management center or under the elevator button.

.

6.Wiring an Elevator Control System

Typical Elevator Wiring Diagram EC10/EC16 Elevator Wiring Diagram

GN

D

LE

D-

LE

D+

Elevator system

Ele

va

tor B

utto

ns c

on

trolle

d lin

e

Elevator Buttons Controlled Panel

GN

D

LE

D-

LE

D+

NC

COM

NO

Elevator system

Ele

va

tor B

utto

ns c

on

trolle

d lin

e

Elevator Buttons Controlled Panel

Backup Output

RS485 Device address 2

4.EX 16 DIP Switch Settings

DIP switches 2-4 are used to set each EX16 Floor Extension Board's unique device address using

RS485 communication. Please keep the EX16 powered off before setting the device address. Each

device address needs to be unique. See example below:

RS485 Device address 3

RS485 Device address 4

1 2 3 4O

5 6 7 8

KE

N

1 2 3 4O

5 6 7 8

KE

N

1 2 3 4O

5 6 7 8

KE

N

Elevator Control Panel

RS485 EXT-

Floor Expansion Board

Fingerprint Reader

DC 12V

Wiegand Reader

TCP/ IP connect with PC

RS485- RS485+

RS485 EXT+

1) The backup input is reserved for the elevator control system.

2) Fire linkage and emergency button function require no software settings. These functions are available when the hardware is installed.

3) GPRS, WIFI and functions marked by * are optional. If these functions are required, contact our business representatives or pre-sale technical support.

Notes:

4) "#" indicates floor , "1# output" indicates that it is connected to the first floor button, the first expansion board is connected to the 11th floor button.

8.EC10 Wiring Terminals Connection

Data_Tx-

Data_Tx+

GND

Data_RxTx-Data_RxTx+Shield

+12VGND

Shield

AC FailBattery Fail

VCC 12V

GND

D0

D1

Shield

LED_GLED_R

BEEP

Hold

Card_present

VCC 12V

GND

D0

D1

Shield

LED_GLED_R

BEEP

Hold

Card_present

Card_present

Hold

BEEP

LED_R

LED_G

ShieldD1

D0

GND

VCC 12V

Card_present

Hold

BEEP

LED_R

LED_G

ShieldD1

D0

GND

VCC 12V

NO

COM

NC

NO

COM

NC

NO

COM

NC

NO

COM

NC

NC

COM

NO

NC

COM

NO

NC

COM

NO

NC

COM

NO

3# Output

2# Output

1# Output

5# Output

4# Output

8# Output

12V Power Input

Shield Wire

AC Fail Detection

12V Power Output

12V Power Out

12V Power Output

12V Power Output

Wiegand Input

Wiegand Input

Wiegand Input

Wiegand Input

Shield Wire

Sheild WireShield Wire

Shield Wire Green

Green

Red

Red

Red

Red

Green

Green

Beep

Beep

Beep

Beep

Controlled Reader Hold

Controlled Reader Hold

Controlled Reader Hold

Card Present

Card Present

Card Present

Card Present

{

{

{

{

{

{

{

{

{

{

{

Shield Wire

}

}

}

}

}

}

}

}

RS 422 Send}

Extension Board

or SR 485 Reader}

Controlled Reader Hold

Output

Output

Output

**

**

*

*

*

pq

RS-4

85 E

XT

WIE

GA

ND 3

IN5

IN6

OU

T5

OU

T6

WIE

GA

ND 4

IN7

IN8

OU

T7

OU

T8

13

13

12

12

110

13

13

12

12

110

16

WIE

GA

ND 1

IN1

IN2

OU

T1

OU

T2

WIE

GA

ND 2

IN3

IN4

OU

T3

OU

T4

13

PO

WE

R1

51

10

12

12

13

13

110

12

12

13

Re

set

Front View Front Side View

RS-2

32

IN9

OU

T9

IN1

2IN

11IN

10

OU

T1

0R

S-4

85

13

13

12

12

12

12

14

14

Output

*

*

**

*

Shield

RS 485-

RS 485+GND

TCP/IP

Analog_input

GND

Analog_input

GND

NO

COM

NC

NO

COM

NC

TCP/IP Comm.

Fire Linkage Input

Emergency button Input

9# Output

Shield Wire

RS485 Comm.

RS485 Ground

***

*

*

}}

Battery Fail Detection

6# Output

7# Output

10# Output

1. Open the elevator press button panel when connecting to the elevator button. Ask the supplier to provide the floor button control circuit. If the supplier can not provide the circuit, exclude the incorrect circuit one

Notice:

by one and ensure the correct connections.

2 . EC10 connects to the computer using TCP/IP or RS485.

4 . EC10 controls access up to 10 , EX16 floors controls access up to 16 floors. An EC10 carries a maximum of 3 expansion boards. Total 58 floors can be controlled when combining EC10 with EX16.

3. EC10 supports ZK fingerprint readers (model FR1200) and RFID card readers (model KR series).

5. The RS485 device address of the fingerprint reader (model FR1200) must be 1. The RS485 device address of the EX16 floor extension board must start from 2.

6. Wiegand reader can connect to the elevator main controller Wiegand 1#~ 4#.

7. IN9 functions as fire linkage signal input. When fire linkage signal works, elevator control system stops working and the elevator retains to original status. (Fire linkage must be passive dry contact signal)

8. IN10 functions as an emergency button. When it is pressed, the whole elevator is not controlled by elevator controller. At this moment, up and down buttons are available. When the emergency button is

not pressed, the elevator retains to the original status.

1

2

3

4

7

5

6

8

9

10

9. ~ Output terminals connect to floor press button.1 10