Quick Start Guide - Amazon S3

2
1 5 2 6 3 7 4 8 Vehicle Dock ANT IN AUDIO OUT DC IN Interoperable Vehicle Antenna 3 Snap the mount onto the vent. To remove, push the mount into the vent, then lift up. Install the Adhesive Mount CAUTION: The adhesive used with the adhesive mount may make it difficult to remove. Do not install this mount on leather surfaces and make sure the air temperature is at least 60°F (15°C). 1 Locate a flat surface for the mount. Make sure there is ample room for the vehicle dock and radio when installed. 2 Clean the surface with the alcohol pad and let it dry thoroughly. 3 Peel off the adhesive liner. Position, press, and hold the adhesive mount in place for 30 seconds. IMPORTANT: Let the adhesive dry for 2 - 3 hours before attaching the vehicle dock and radio to the mount. For best results let dry for 24 hours. Vehicle Installation NOTE: Do it yourself with the step-by-step instructions below if your vehicle has a cassette player or audio input. If your vehicle does not have a cassette player or audio input, professional installation with XM SureConnect or XM FM Direct is strongly recommended (each sold separately). Step 1: The Big Decision. Pick a spot for your radio. Vent or Dashboard? You can use either the vent mount or the adhesive mount for your radio depending on your particular situation. Install the Vent Mount 1 Locate a vent with horizontal slats sturdy enough to hold your vehicle dock and radio. 2 Adjust the clamps to fit your vent. Antenna placement options for other vehicles. Pickup Truck - Above front windshield, on the roof toward front of cab. Centered between right and left sides. Convertible - On trunk lid, at least 3” from seam. Centered between right and left sides. 2 Hide the wires inside. The best place to hide your antenna wire depends on your vehicle. It’s usually easiest to run the wire from the rear of the vehicle to the front toward the radio by routing the cable along the interior trim where it meets the carpet, by gently pushing it behind the edges of the trim. Then bring the cable out from the trim and route it under the carpet to the dashboard or console. Plug the cable into the radio and coil any extra wires under the carpet or floor mat. TIP! Always be careful to include enough slack in your cable to accommodate open doors or trunk lids. Use things typically found around the home, like electrical tape or twist ties, to secure cables in areas so that hinges do not pinch the cable. Hide any excess cable in the trim. WARNINGS: When using this product it is always important to keep your eyes on the road and hands on the wheel. Not doing so could result in personal injury, death and/or damage to your SIRIUS XM Radio, accessories and /or to your vehicle or other property. The radio should be placed in your vehicle where it will not interfere with the function of safety features, e.g., deployment of airbags. Failure to correctly place radio may result in injury to you or others if the unit becomes detached during an accident and/or obstructs the deployment of an airbag. What’s in the Box? Radio Remote Control Alcohol Pad Vehicle Power Adapter Step 3: Connect Your Radio. Almost there! 1 Plug the Antenna into the vehicle dock’s ANT IN connection. 2 Plug the Power Adapter into the vehicle dock’s DC IN connection. 3 Plug one of the audio adapters into the vehicle dock’s AUDIO OUT connection. • Use the Aux In Cable if your vehicle has an audio input jack. • Use the Cassette Adapter if your vehicle has a built-in cassette player. 4 Insert the dock into the vent or adhesive mount. 5 Insert your radio into the dock. NOTE: As mentioned, if your vehicle is not equipped with a cassette player or an audio input, you will need to use either XM SureConnect or XM FM Direct (each sold separately at xmradio.com/ mirgeaccessories). Professional installation is strongly recommended for either of these options, and it can also help improve your radio’s reception and significantly reduce the visibility of wires. XM SureConnect (sold separately): You can listen to your radio through your vehicle’s stereo by using the XM SureConnect. Simply find an unused FM frequency on the stereo and set your radio to transmit on that same frequency. Refer to Set the FM Frequency page in your user guide for more information. XM FM Direct Adapter (sold separately): This option directly connects the radio to your vehicle’s audio system and antenna. Interoperable Vehicle Antenna Vehicle Power Adapter Cassette Adapter Vehicle Dock Aux In Cable —OR— Cassette Adapter Vent Mount ! ! ! Dash Vent Dash Vent 4 Turn the swivel to accommodate the vehicle dock and radio. Adjust the tension via the center screw. To remove, carefully lift the adhesive pad with your fingers or a spoon. Warming the pad with a hair dryer for several minutes will help soften the adhesive. Step 2: Mount the Interoperable Vehicle Antenna. You’ll be glad you did this right. YOU MUST USE THE INCLUDED INTEROPERABLE ANTENNA WITH THIS RADIO 1 Place the antenna outside. Leave at least 3” of metal around the antenna. Use the rubber tail cover to hide and protect the exposed wire. Feed the wire under the rubber molding around the back windshield, into the seal around the trunk. Route the cable along trunk wall and into the interior cabin from there. Magnet You can adjust this screw to adjust the tension of the mount with a screwdriver. ! ! ! Aux In Cable Adhesive Mount SUV Sedan Vent Mount Adhesive Mount Activate Before you can listen to any of the great channels, you must first activate your radio. NOTE! Make sure your radio is in SIRIUS mode by pressing the SAT button. See page 24 in the user guide for more information. 1 Make sure your radio is properly installed and receiving the SIRIUS signal so that you can hear the audio on SIRIUS Channel 184. 2 Make a note of your radio’s ID number. You can find it: • On Channel 0 on either SIRIUS or XM • On the rear package label • On the label on the back of your radio 3 Activate your service: • Online: Go to www.sirius.com/mirge OR • By phone: call 1-888-539-SIRIUS (1-888-539-7474) 4 Depending on which Satellite Radio services you activated, channels will become available about 10 to 15 minutes after activation — although it may take up to an hour. Your radio must remain ON until activated. ! ! ! Step 4: Turn on Your Radio and Test for Sound. 1 Turn on your vehicle’s radio. 2 Insert the cassette adapter or AUX In Cable. NOTE: If you are using the XM SureConnect or the XM FM Direct adapter, refer to Turn the FM modulator ON/OFF on page 54 of the user guide for more information. 3 Turn ON your radio. NOTE: You may experience a brief delay while your radio powers up. If you press the power button during this time, you will see a “Please Wait” message. Antenna Cover/Tail

Transcript of Quick Start Guide - Amazon S3

Page 1: Quick Start Guide - Amazon S3

1

5

2

6

3

7

4

8

Vehicle Dock

19

ANT IN AUDIO OUTDC IN

Interoperable Vehicle Antenna

3 Snap the mount onto the vent.

To remove, push the mount into the vent, then lift up.

Install the Adhesive Mount CAUTION: The adhesive used with the adhesive mount may make it difficult to remove. Do not

install this mount on leather surfaces and make sure the air temperature is at least 60°F (15°C).

1 Locate a flat surface for the mount. Make sure there is ample room for the vehicle dock and radio when installed.

2 Clean the surface with the alcohol pad and let it dry thoroughly.

3 Peel off the adhesive liner. Position, press, and hold the adhesive mount in place for 30 seconds.

IMPORTANT: Let the adhesive dry for 2 - 3 hours before attaching the vehicle dock and radio to the mount. For best results let dry for 24 hours.

Vehicle Installation NOTE: Do it yourself with the step-by-step instructions below if your vehicle has a cassette player or

audio input. If your vehicle does not have a cassette player or audio input, professional installation with XM SureConnect or XM FM Direct is strongly recommended (each sold separately).

Step 1: The Big Decision. Pick a spot for your radio. Vent or Dashboard?

You can use either the vent mount or the adhesive mount for your radio depending on your particular situation.

Install the Vent Mount

1 Locate a vent with horizontal slats sturdy enough to hold your vehicle dock and radio.

2 Adjust the clamps to fit your vent.

Antenna placement options for other vehicles.

• Pickup Truck - Above front windshield, on the roof toward front of cab. Centered between right and left sides.

• Convertible - On trunk lid, at least 3” from seam. Centered between right and left sides.

2 Hide the wires inside. The best place to hide your antenna wire depends on your vehicle. It’s usually easiest to run the wire from the rear of the vehicle to the front toward the radio by routing the cable along the interior trim where it meets the carpet, by gently pushing it behind the edges of the trim. Then bring the cable out from the trim and route it under the carpet to the dashboard or console. Plug the cable into the radio and coil any extra wires under the carpet or floor mat.

TIP! Always be careful to include enough slack in your cable to accommodate open doors or trunk lids. Use things typically found around the home, like electrical tape or twist ties, to secure cables in areas so that hinges do not pinch the cable. Hide any excess cable in the trim.

WARNINGS: When using this product it is always important to keep your eyes on the road and hands on the wheel. Not doing so could result in personal injury, death and/or damage to your SIRIUS XM Radio, accessories and /or to your vehicle or other property.

The radio should be placed in your vehicle where it will not interfere with the function of safety features, e.g., deployment of airbags. Failure to correctly place radio may result in injury to you or others if the unit becomes detached during an accident and/or obstructs the deployment of an airbag.

What’s in the Box?

Radio Remote Control

Alcohol Pad

Vehicle Power Adapter

Step 3: Connect Your Radio. Almost there!

1 Plug the Antenna into the vehicle dock’s ANT IN connection.

2 Plug the Power Adapter into the vehicle dock’s DC IN connection.

3 Plug one of the audio adapters into the vehicle dock’s AUDIO OUT connection.

• Use the Aux In Cable if your vehicle has an audio input jack.

• Use the Cassette Adapter if your vehicle has a built-in cassette player.

4 Insert the dock into the vent or adhesive mount.

5 Insert your radio into the dock.

NOTE: As mentioned, if your vehicle is not equipped with a cassette player or an audio input, you will need to use either XM SureConnect or XM FM Direct (each sold separately at xmradio.com/mirgeaccessories). Professional installation is strongly recommended for either of these options, and it can also help improve your radio’s reception and significantly reduce the visibility of wires.

• XM SureConnect (sold separately): You can listen to your radio through your vehicle’s stereo by using the XM SureConnect. Simply find an unused FM frequency on the stereo and set your radio to transmit on that same frequency. Refer to Set the FM Frequency page in your user guide for more information.

• XM FM Direct Adapter (sold separately): This option directly connects the radio to your vehicle’s audio system and antenna.

Interoperable Vehicle Antenna Vehicle Power

AdapterCassette Adapter

Vehicle Dock

Aux In Cable—OR—

Cassette Adapter

Vent Mount

!

! !

Dash

Vent

Dash

Vent

4 Turn the swivel to accommodate the vehicle dock and radio. Adjust the tension via the center screw.

To remove, carefully lift the adhesive pad with your fingers or a spoon. Warming the pad with a hair dryer for several minutes will help soften the adhesive.

Step 2: Mount the Interoperable Vehicle Antenna. You’ll be glad you did this right.

YOU MUST USE THE INCLUDED INTEROPERABLE ANTENNA WITH THIS RADIO

1 Place the antenna outside. Leave at least 3” of metal around the antenna. Use the rubber tail cover to hide and protect the exposed wire. Feed the wire under the rubber molding around the back windshield, into the seal around the trunk. Route the cable along trunk wall and into the interior cabin from there. Magnet

You can adjust this screw to adjust the tension of the mount with a screwdriver.

!

!

!

Aux In Cable

Adhesive Mount

SUV

Sedan

Vent Mount Adhesive Mount

Activate Before you can listen to any of the great channels, you must first activate your radio.

NOTE! Make sure your radio is in SIRIUS mode by pressing the SAT button. See page 24 in the user guide for more information.

1 Make sure your radio is properly installed and receiving the SIRIUS signal so that you can hear the audio on SIRIUS Channel 184.

2 Make a note of your radio’s ID number. You can find it:

• On Channel 0 on either SIRIUS or XM

• On the rear package label

• On the label on the back of your radio

3 Activate your service:

• Online: Go to www.sirius.com/mirge

OR

• By phone: call 1-888-539-SIRIUS (1-888-539-7474)

4 Depending on which Satellite Radio services you activated, channels will become available about 10 to 15 minutes after activation — although it may take up to an hour. Your radio must remain ON until activated.

!

!

!

Step 4: Turn on Your Radio and Test for Sound.

1 Turn on your vehicle’s radio.

2 Insert the cassette adapter or AUX In Cable.

NOTE: If you are using the XM SureConnect or the XM FM Direct adapter, refer to Turn the FM modulator ON/OFF on page 54 of the user guide for more information.

3 Turn ON your radio.

NOTE: You may experience a brief delay while your radio powers up. If you press the power button during this time, you will see a “Please Wait” message.

Antenna Cover/Tail

Page 2: Quick Start Guide - Amazon S3

9

12

10

13

11

14

Use Your RadioListen to SIRIUS or XM

Select the radio service

1 The currently-active radio service logo is shown in the display’s channel information bar.

2 Press the SAT button on the radio or remote to switch to the other radio service. The radio will play the channel that was last tuned in that service.

Set Your Favorite Channel

You can assign up to 10 presets of your favorite channels in each satellite service to the number buttons so you can quickly access them.

To assign a preset to a button:

1 Tune to the desired channel.

2 Be sure you are in Favorite Channels mode. Press FAV until Favorite Channels appears in the title bar.

3 Press and hold the number button you want to use for that preset.

To listen to a favorite channel:

1 Be sure you are in Favorite Channels mode. Press FAV until Favorite Channels appears in the title bar.

2 Press the number button assigned to your favorite channel.

TIP! To see your list of Favorite Channels, press or . Select a favorite and press the SELECT button to listen to that channel.

Split Screen Display Mode

You can view multiple channels on the display to see what else is playing.

To change the mode, press DISPLAY.

TIP! When in Split Screen with Channel List, you can scroll through the list of channels, just like when it appears on the full screen. Press or to change categories. Press the SELECT button to select a channel.

TIP! Press jUMP to tune to the previous channel on active service.

Accessories To Enhance Your Listening Experience

Enjoy your favorite SIRIUS and XM programming almost anywhere with a MiRGE home kit, sound system, or additional vehicle kit, each sold separately.

These and other MiRGE accessories ONLY available at xmradio.com/mirgeaccessories.

©2009 SIRIUS XM Radio Inc. SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. / “BBC” and “Radio One” are trademarks of the British Broadcasting Corporation and are used under license. BBC logo ©BBC 1996. Radio 1 logo ©BBC 2001. / Cosmopolitan® is a registered trademark of Hearst Communications, Inc ./ Elvis Radio logo ©EPE Reg. U.S. Pat &TM off. / IndyCar (and Design) are registered trademarks of Brickyard Trademarks, Inc., used with permission. / Major League Baseball trademarks and copyrights are used with permission of Major League Baseball Properties, Inc. Visit the official website at MLB.com. Games subject to availability and change and may not include all pre-season games. / NASCAR® is a registered trademark of the National Association for Stock Car Auto Racing, Inc. / The NBA identifications are the intellectual property of NBA Properties, Inc. and the respective NBA member teams. ©2008 NBA Properties, Inc. / “NCAA” and the NCAA Basketball logo are registered trademarks of the National Collegiate Athletic Association./ ©2008 NFL Properties. All NFL-related trademarks are trademarks of the National Football League./ NHL and NHL Shield are registered trademarks of the National Hockey League. ©NHL 2008. All NHL logos and marks and NHL team logos and marks depicted herein are the property of the NHL and the respective teams and may not be reproduced without the prior written consent of NHL Enterprises, L.P. The Home Ice® channel is a registered trademark of XM Satellite Radio Inc./ The Swinger Golfer logo is a registered trademark of PGA TOUR, Inc. / All other marks and logos are the property of their respective owners. All rights reserved.

sirius.com/mirge

Getting Started Guide (GSG1208)

Getting Started Guide

Selecting a channel

1 Turn the kNOB (radio) or use the Up/Down buttons (remote) to scroll through the list of channels.

2 You’ll see the channel’s logo and current artist. In a few seconds, the current song title appears.

3 Press the SELECT button to select a channel.

TIP! You can configure the radio to automatically tune to the channel you scroll to. Refer to page 34 of the user guide for more instructions.

View a category

Channels are organized into categories to make it easier for you to find the ones that suit your taste.

1 To view a category, press the LEFT or RIGHT arrows ( or ).

2 Scroll through the category to find the channel you want.

3 Press the SELECT button.

TIP! To briefly listen to each channel in the category, select SCAN, then press the SELECT button.

!

!

!

!

SIRIUS Radio Service XM Radio Service

60-Minute REPLAY ButtonsPause, rewind and replay up to 60 minutes of live radio.

Radio Functions

POWER Button

DISPLAYCustomize the way content on the display is shown.

< LEFT and RIGHT > ArrowsSearch for channels by category.

5-way Navigation kNOBPreviews channels; also selects various menu options.

MENU Access advanced features and configuration options.

SELECT ButtonConfirms selection for channel and menu items, also press and hold to TuneSelect.

FAVORITES Choose between direct channel entry or favorite channels mode.

jUMP Switches between current channel and previous channel.

SATELLITE Switches between the SIRIUS and XM satellite radio.

NUMBER Buttons Enter a channel directly or select your favorite channels.

Split screen showing Channel List Split screen showing Category List

Split screen showing Previous Channel Split screen showing Favorite Channels