Quick Setup Guide Location - The Home Depot€¦ · Toutes spécifications sont sujettes à...

12
© 2014 553_Q - 02/14 1 A Watts Water Technologies Company Interior Wall 5 feet 1.5 m Exterior Wall 1. Location 2. Remove Mounting Base 3. Install Mounting Base 3 1 /4(83 mm) Thermostat Base Stud Gang Box Wall Stud Thermostat Base Behind Door tekmarNet ® Thermostat 553 Quick Setup Guide 553 _ Q 02/14 Zoning Replaces: 01/14

Transcript of Quick Setup Guide Location - The Home Depot€¦ · Toutes spécifications sont sujettes à...

© 2014 553_Q - 02/141A Watts Water Technologies Company

InteriorWall

5 feet1.5 m

ExteriorWall

1. Location

2. Remove Mounting Base

3. Install Mounting Base

3 1/4”(83 mm)

ThermostatBase

Stud

GangBox

Wall

StudThermostat

Base

BehindDoor

tekmarNet® Thermostat 553

Quick Setup Guide

553_Q02/14

Zoning Replaces: 01/14

© 2014 553_Q - 02/142A Watts Water Technologies Company

4. Switch Settings

5. Wiring

Switch Position Action

1ON LOCK Access level

adjustment is not available.

OFF UNLOCK Access level adjustment is available.

tekmarNet Thermostat 553Two Stage Heat, One Stage Cool, Fan

SwitchSettings

www.tekmarcontrols.com

Lock

edck

/

ON

1 2

Back of Thermostat

tekmarNet®4 Wiring Example

See 553_A for complete wiring details.

WRYG

OptionalOutdoorSensor

070

OptionalSlab

Sensor079Furnace

andAir Conditioner

tN4 Wiring Center or Zone Manager

tN4 C WR

CtN2

tN4tN2

RRh W Rc Y G/O S1 S2ACC Com

No Power

WRYG

OptionalOutdoorSensor

070

OptionalSlab

Sensor079Furnace

andAir Conditioner

tN2 Wiring Center,House Control orZone Manager

tN2 tN2

CtN2

tN4tN2

RRh W Rc Y G/O S1 S2ACC Com

No Power

tekmarNet®2 Wiring Example

© 2014 553_Q - 02/143A Watts Water Technologies Company

6. Install the Thermostat

7. User Interface

ThermostatFront

Push

ThermostatBase

Adjustthe Time

Adjust theSchedule

Display Humidity, Heat & Cool settings, Floor or Outdoor temperature

Away Key

Switch betweenAuto, Heat, Cool, Off &

Emergency Mode Return to the ‘Home’ Screen from any menuAdjust the

Temperature

RoomTemperature

Turn the Fan on

HomeButton

All specifications are subjectto change without notice

4 553_Q - 02/14.

Product design, software and literature are Copyright ©2014 by tekmar Control Systems Ltd., A Watts Water Technologies Company. Head Offi ce: 5100 Silver Star Road, Vernon, B.C. Canada V1B 3K4, 250-545-7749, Fax. 250-545-0650 Web Site: www.tekmarControls.com

The following settings are essential to the successful operation of the system.Step 1: Set switch setting #1 and tekmarNet® system control located in the mechanical room to Unlock to change Access level to Installer. Return to Lock setting once installation has been completed.Step 2: Press and hold “Home” button for 3 seconds to enter programming menus.Step 3: Touch NEXT to locate the Setup Menu and touch ENTER.

8. Critical Settings

Setup Menu Settings Range Default

SENSOR 1Select the type of sensor connected to auxiliary sensor input 1.

OFF, ROOM, FLOR (floor), COIL, DUCT OFF

SENSOR 2Select the type of sensor connected to auxiliary sensor input 2.

OFF, ROOM, FLOR (floor), OUT (outdoor) OFF

ROOM SENSORSelect if the built-in room temperature sensor is on or off.

OFF or ON ON

HUMIDITY SENSORSelect if the built-in humidity sensor is on or off.

OFF or ON ON

Y RELAYSelect the cooling equipment the Y relay operates.

OFF, HP (heat pump), AC (air conditioner), HUM (humidity)

AC

W TERMINAL UNITSelect the terminal unit type of the first stage of heat W.

NONE, HRF1, HRF2, CONV, COIL, FURN, OTHR

HRF1 (tekmarNet®

System Control)OTHR (standalone)

ACC RELAYSelect the operation of the accessory relay.

OFF, W2, HUM, DHUM, HRV, FAN W2

W2 TERMINAL UNITSelect the type of backup heating.

CONV, COIL, FURN (furnace), OTHR (other) FURN

W2 SOURCESelect the second stage W2 hydronic heat source.

BOIL, TANK, MIX BOIL

G/O RELAYSelect the equipment the G / O relay operates.

FAN or OFF (conventional heating)O or B (heat pump)

FAN (conventional)O (heat pump)

For a full list of settings and operational details, please refer to the thermostat Installation and Operation Manual (553_D) available from www.tekmarControls.com

© 2014 553_Q - 02/145Une Entreprise de Watts Water Technologies

1. Emplacement

2. Retirez la base de montage

3. Installez la base de montage

3 1/4”(83 mm)

ThermostatBase

Stud

GangBox

Wall

StudThermostat

Base

Derrièreporte

Mur extérieur

Mur intérieur

5 pi.1,5 m

Mur

Base de thermostat

Base de thermostat

Commutateur boîte

Goujon

Goujon

tekmarNet® Thermostat 553

Guide d'installation rapide

553_Q02/14

Zonage Remplace: 01/14

© 2014 553_Q - 02/146Une Entreprise de Watts Water Technologies

WRYG

OptionalOutdoorSensor

070

OptionalSlab

Sensor079Furnace

andAir Conditioner

tN4 Wiring Center or Zone Manager

tN4 C WR

CtN2

tN4tN2

RRh W Rc Y G/O S1 S2ACC Com

No Power

4. Réglages des commutateurs

5. Filage

Commutateur Position Action

1

ONVERROUILLAGE Le réglage du niveau d'accès n'est pas disponible.

OFFDÉVERROUILLAGE Le réglage du niveau d’accès est disponible.

tekmarNet Thermostat 553Two Stage Heat, One Stage Cool, Fan

SwitchSettings

www.tekmarcontrols.com

Lock

edck

/

ON

1 2

Dos du thermostat

tekmarNet®4 exemple de filage

Référence 553_A pour plus de détails sur le filage complet.

WRYG

OptionalOutdoorSensor

070

OptionalSlab

Sensor079Furnace

andAir Conditioner

tN2 Wiring Center,House Control orZone Manager

tN2 tN2

CtN2

tN4tN2

RRh W Rc Y G/O S1 S2ACC Com

No Power

tekmarNet®2 exemple de filage

Capteurde dalle079 (en option)

Capteurde dalle079 (en option)

Capteur extérieur 070(en option)

Capteur extérieur 070(en option)

Fourneau et Climatiseur

Fourneau et Climatiseur

tN4 contrôle des zones

tN2 contrôle des zones

© 2014 553_Q - 02/147Une Entreprise de Watts Water Technologies

6. Installer le Thermostat

7. Interface d’utilisateur

ThermostatFront

Push

ThermostatBase

HomeButton

Régler l’heure

Régler le programme

Clè à distance

Basculer entre Auto, Chaud,

Frais, Off & mode d’urgence

Régler latempérature

Affichage de l’humidité, des paramètres de chaleur et du frais, de la température ambiante ou du sol

Température de la chambre

Allumer la ventillation

Bouton daccueil. Revenir à l’écran «Home» (Accueil) depuis n’importe quel menu. Appuyez et maintenez enfoncé pendant 3 secondes pour accéder aux menus de programmation.

Base de thermostat

Façade du thermostat

Poussoir

Toutes spécifications sont sujettes à changements sans préavis. Imprimé au Canada.

8 553_Q - 02/14.

Conception de produit, logiciel et littérature sont des droits réservés ©2014 par tekmar Control Systems Ltd., Une Entreprise de Watts Water Technologies. Bureau Principal: 5100 Silver Star Road, Vernon, B.C. Canada V1B 3K4, 250-545-7749, Téléc: 250-545-0650 Site Web: www.tekmarControls.com

Les paramètres suivants sont essentiels au bon fonctionnement du système.Étape 1: Définir le réglage du commutateur sur #1 et le système de contrôle tekmarNet® situé dans la salle mécanique sur Déverrouiller pour changer le niveau d’accès à l’installateur. Retour pour Verrouiller réglage, une fois l’installation terminée.Étape 2: Appuyez et maintenez le bouton «Home» pendant 3 secondes pour entrer dans les menus de programmation.Étape 3: Touchez SUIVANT pour localiser le menu de configuration et appuyez sur ENTRER.

8. Paramètres critiques

Réglages du menu de configuration Gamme Par défautCAPTEUR 1Sélectionner le type de capteur relié à l’entrée auxiliaire du capteur 1.

OFF, ROOM, FLOR (sol), COIL, DUCT OFF

CAPTEUR 2Sélectionner le type de capteur relié à l’entrée auxiliaire du capteur 2.

OFF, ROOM, FLOR (sol), OUT (en plein air) OFF

CAPTEUR DE CHAMBRESélectionnez si le capteur intégré de la température ambiante est allumé ou éteint.

OFF ou ON ON

CAPTEUR D'HUMIDITÉSélectionnez si le capteur d'humidité intégré est activé ou pas.

OFF ou ON ON

RELAIS YSélectionnez l'équipement de refroidissement que relais Y active.

OFF, HP (pompe à chaleur), AC (climatiseur), HUM (humidité)

AC

UNITÉ DU TERMINALE WSélectionnez le type d’unité du terminal de la première étape de chauffage W.

NONE, HRF1, HRF2, CONV, COIL, FURN, OTHR

HRF1 (tekmarNet®

Contrôle de Système)OTHR (autonome)

RELAIS ACCESSOIRESélectionnez l’appareil que le relais accessoire active.

OFF, W2, HUM, DHUM, HRV, FAN (ventilateur) W2

UNITÉ DU TERMINALE W2Sélectionnez le type de chauffage d'appoint.

CONV, COIL, FURN (fourneau), OTHR (autre) FURN

SOURCE DE W2Sélectionnez la source de chaleur hydroniques de la deuxième étape W2.

BOIL (ébullition), TANK (réservoir), MIX (melange) BOIL (ébullition)

RELAIS G/OSélectionnez l'équipement le relais G / O est ouvert.

FAN (ventilateur) ou OFF (chauffage conventionnel)O ou B (pompe à chaleur)

FAN (ventilateur) (classique)O (pompe à chaleur)

Pour une liste complète des paramètres et les détails opérationnels, s’il vous plaît se référer à l’installation du thermostat et mode d’emploi (553_D) disponible sur www.tekmarControls.com

© 2014 553_Q - 02/149Una Compañía de Watts Water Technologies

1. Ubicación

2. Quite la base de montaje

3. Instalación de la base de montaje

3 1/4”(83 mm)

ThermostatBase

Stud

GangBox

Wall

StudThermostat

Base

Detrásde la puerta

Pared exterior

Pared interior

5 pies1,5 m

Base del termostato

Base del termostato

ParedCaja de

interruptor

tekmarNet® Thermostat 553

Guía de instalación rápida

553_Q02/14

División en zonas

Remplazado por: 01/14

© 2014 553_Q - 02/1410Una Compañía de Watts Water Technologies

4. Ajustes del interruptor

5. Cableado

Interruptor Posición Acción

1

ONLOCK (BLOQUEADO) el nivel de acceso para ajustes se encuentra bloqueado.

OFFUNLOCK (DESBLOQUEADO) el nivel de acceso para ajustes se encuentra disponible.

tekmarNet Thermostat 553Two Stage Heat, One Stage Cool, Fan

SwitchSettings

www.tekmarcontrols.com

Lock

edck

/

ON

1 2

Parte trasera del termostato

tekmarNet®4 ejemplo de cableado

Referencia 553_A para detalles completos del cableado.

WRYG

OptionalOutdoorSensor

070

OptionalSlab

Sensor079Furnace

andAir Conditioner

tN4 Wiring Center or Zone Manager

tN4 C WR

CtN2

tN4tN2

RRh W Rc Y G/O S1 S2ACC Com

No Power

WRYG

OptionalOutdoorSensor

070

OptionalSlab

Sensor079Furnace

andAir Conditioner

tN2 Wiring Center,House Control orZone Manager

tN2 tN2

CtN2

tN4tN2

RRh W Rc Y G/O S1 S2ACC Com

No Power

tekmarNet®2 ejemplo de cableado

Caldera y acondicionador de aire

Caldera y acondicionador

de aire

tN4 control de zonas

tN2 control de zonas

Sensor de exterior opcional 070

Sensor de exterior opcional 070

Sensor de losa opcional 079

Sensor de losa opcional 079

© 2014 553_Q - 02/1411Una Compañía de Watts Water Technologies

6. Instalación del termostato

7. Interfaz del usuario

ThermostatFront

Push

ThermostatBaseBase del

termostato

Frente del termostato

Eempuje

HomeButton

Ajustarhora

Temperatura ambiente

Prender el ventilador

Botón Inicio. Vuelva a la pantalla inicial desde cualquier otro menú. Mantenga presionado por 3 segundos para acceder al menú del programa.

Ajustar la programación

Tecla de salida

Ajustar la temperatura

Elija entre Auto (Automático),Heat (Calefacción),

Cool (Refrigeración), Off (Apagado) y Emergency

Mode (Modo de emergencia)

Mostrar los ajustes de humedad, calefacción y refrigeración, la temperatura del Piso y Externa.

Todas las especificaciones pueden cambiar sin previo aviso.

12 553_Q - 02/14.

El diseño del producto, software y la literatura poseen derechos reservados ©2014 a nombre de tekmar Control Systems Ltd., Una Compañía de Watts Water Technologies Ofi cina Principal: 5100 Silver Star Road, Vernon, B.C. Canadá V1B 3K4, 250-545-7749, Fax. 250-545-0650 Sitio web: www.tekmarControls.com

Las siguientes configuraciones son esenciales para que el sistema trabaje de manera correcta.Paso 1: Desbloquee (opción UNLOCK) el ajuste número uno del interruptor y del control del sistema tekmarNet® para cambiar el nivel de accesibilidad a Instalador. Cámbielo nuevamente a Bloquear (opción Lock) luego de finalizar la instalación.Paso 2: Mantenga presionado el botón “Home” por 3 segundos para ingresar a los menús de programación.Paso 3: Presione el botón NEXT (SIGUIENTE) para localizar el menú de SETUP (Instalación) y presione ENTER (ENTRAR).

8. Ajustes críticos

Ajustes del menú de instalación Rango PredeterminadoSENSOR 1Seleccione el tipo de sensor conectado a la entrada número 1 para sensor auxiliares.

OFF, ROOM, FLOR (piso), COIL, DUCT OFF

SENSOR 2Seleccione el tipo de sensor conectado a la entrada número 2 para sensor auxiliares.

OFF, ROOM (ambiente), FLOR (piso), OUT (exterior) OFF

SENSOR AMBIENTEPrenda o apague el sensor integrado de la temperatura del aire en el ambiente.

OFF o ON ON

SENSOR DE HUMEDADSeleccione si el sensor de humedad integrado estará prendido o apagado.

OFF o ON ON

RELÉ YSeleccione el equipo de refrigeración que accionara el relé Y.

OFF, HP (bomba de calor), AC (acondicionador de aire), HUM (humedad)

AC

TIPO DE TERMINAL WSeleccione el tipo de unidad terminal de la primera etapa de calefacción W.

NONE (Ninguna), HRF1, HRF2, CONV, COIL, FURN, OTHR

HRF1 (Sistema de control tekmarNet ®)OTHR (Otro)

RELÉ ADICIONALSeleccione el equipo que el relé adicional accionará.

OFF, W2, HUM, DHUM, HRV, FAN W2

TIPO DE TERMINAL W2Seleccione el tipo de calefacción de respaldo.

CONV, COIL, FURN (caldera), OTHR (otro) FURN

FUENTE W2Seleccione la fuente de calefacción hidrónica W2 de segunda etapa.

BOIL, TANK, MIX BOIL

RELÉ G/OSeleccione el equipo que el relé G /O utiliza.

FAN (ventilador) o OFF(calefacción convencional)O o B (bomba de calefacción)

FAN (onvencional)O (bomba de calefacción)

Para una lista completa de ajustes y detalles funcionales, por favor diríjase al Manual de Instalación y manejo del termostato (553_D) disponible en www.tekmarControls.com