QinetiQ - Aegean · PDF fileRADAR INTERCONNECTIONS 1 Channel Radar Overlay facility tested at...

QinetiQ

NOTIFIED BODYNo 0191

CERTIFICATE OF TYPE APPROVAL(EC Certificate of Type Examination - Module B)(Marine Equipment Directive - 96/98/EC, as amended *1)

Applicant:-

Manufacturer:-Kelvin Hughes Ltd

Kelvin Hughes LtdNew North Road, Hainault

New North Road, HainaultIlford, Essex IG6 2UR

Ilford, Essex IG6 2URUnited Kingdom

United Kingdom

This is to certify that the applicant has submitted details of a:-

Electronic Chart Display And Information System (ECDIS)With Backup, and Raster Chart Display System

(COMMISSION DIRECTIVE 2008/67/EC - ITEM A.1/4.30)Of system type known and designated as:-

MantaDigital, 20" or 26" Widescreen ECDIS(Comprising component parts and having technical characteristics shown in schedule 1)

and that these have been assessed, tested and when used in a combination of component parts asdescribed in the attached schedules, is CERTIFIED as complying with the relevant parts of:

IEC 61174:2008, "Electronic Chart Display And Information System (ECDIS)"IEC 62288:2008, "Presentation of navigation-related information on shipborne navigational displays"IEC 60945 : 2002 "General Requirements for Marine Navigation Equipment"

(being specifications for Technical Characteristics and Methods of measurements published by theInternational Electrotechnical Commission and equivalent to BS EN 61174:2008 and BS EN 60945:2002).

It is also RECOGNISED that the equipment conforms to performance standards not inferior to thoseadopted by the International Maritime Organisation, and which are contained in ResolutionMSC.232(82), Resolution MSC.191(79) and Resolution A694(17).

DATE of ISSUE:

22nd December 2009

SIGNED:

=

r

?

DATE of EXPIRY:

21St December 2014

R A Sharp

Authorised Signatory

Certificate Number:

QQ-MED-23/09-01

EU/USCG Mutual Recognition Agreement

This equipment category is not yet covered by the MRACouncil Decision 2004/425/EC

This Certificate is Valid until expiry date shown, subject to thestandard conditions of issue printed on page 6Kelvin Hughes Ltd are Module D registered with QinetiQ in accordwith standard condition 3, ref Certificates DQAS-06/01-KH001R3.

QinetiQCody Technology ParkIvely Road, FarnboroughHampshire. GU14 OLX

Under the terms of the United Kingdom Statutory Instrument, No 1957: 1999, QinetiQ Ltd has been Notified to the European Commissionby the Maritime and Coastguard Agency as a Body authorised to conduct Conformity Assessment procedures under the provisions of theEuropean Council Directive 96/98/EC (as amended) on Marine Equipment and issue Certificates of Type Approval.

mCaMaritime and Coastguard Agency

The MCA is an Executive Agency ofthe Department for Transport.

QinetiQ/E ES/EMES/MED/002/2.0

of 6Commission Directives 2008/67/EC, 2002/75/EC & 2002/84/EC*1

Certificate of Type Approval - Schedule 1MantaDigital 26" Widescreen ECDIS

The applicant declared that the following units when combined form an operational Marine ShipborneECDIS equipment. The units below have been assessed & tested and satisfactory details of these unitswere included in the technical file.. These units form systems consistent with the Item DescriptionA1/4.30, given in Annex Al of Directive 2008/67/EC .

SYSTEM comprising of:-

MantaDigital Desktop Display Unit (26 " Colour LCD)including Trackerball & Keyboard (MDD-Alol)

MDD-A30-26-ABAAor MantaDigital Console Display Unit (26 " Colour LCD)

MDD-A20-26

*1and MantaDigital Trackerball & Keyboard

MDD-A101and MantaDigital ECDIS Processing Unit

MDP-A2

*2, 3or MantaDigital Deck mount Pedestal Display Unit (26" Colour LCD)

integrated Processor unit, Trackerball & Keyboard

MDD-A2-26

*2, 3

SOFTWARE:- MantaDigital Core Software (ZM-1816 ECDIS)

Version 4.xx

*4

Seven Cs Presentation Library,

Version 3.4.1

*4 End of List

NOTES:-

1

The console display unit is a panel mounting display for integrating into a ships bridge console.

2

This approval is valid for operation in ECDIS and RCDS chart display modes only.Use in ECS mode is reserved for Non-SOLAS vessels or where the ships operating plan agreed by Flag orClass authority allows.

3

This ECDIS system has additional controls for a Track Control Autopilot facility, this function is not covered by thisapproval. The Track Control Autopilot will carry its own Approvals Certificate.

4

This approval remains valid for equipment including subsequent Minor software amendments, as allowed by theN.xx format (xx represents numerals), where written details of any such modifications have been submitted to andaccepted by QinetiQ.

5

This approval recognises the earlier BSH approvals of this ECDIS series with software versions prior to version 4.00certificate BSH/4612/4300391/07 issued 23 February 200,7refers.

Technical Characteristics

PARAMETER PROVISION COMMENT

DISPLAYED CHART AREA Chart Size343mm x 343mm

In Route Monitoring Mode26" Widescreen Colour Liquid Crystal Display (LCD).

IEC 61162-1 SERIAL (NMEA)PORTS

Listner 16Talker -16

Conformity to IEC 61162-1:2007.Presence & fault check on messages provide warning status

ANALOGUE SIGNAL PORTS Log & Gyro Pulse log input and Syncro/Stepper Gyro input

RADAR INTERCONNECTIONS 1 Channel Radar Overlay facility tested at QinetiQ Shoeburyness test range.Declared as suitable for operation with Manta & MantaDigitalseries radar.

Back-Up Arrangements Via Ethernet linkto 2"d ECDIS

A second MantaDigital ECDIS running software as listed above mayform a back-up. MantaDigital Chart Radar operating in ECDIS modecould also form an ECDIS Back-up.

TEMPERATURE RANGE Protected& IEC 945 CLASS

Exposed-15°C to +55°C.-25°C to +70°C

-- All units-- None

POWER SOURCE 110V / 220V AC50-60Hz

Selection between voltage is automatic.Short term operation ( �45s) on power failure to avoid manual re-initialisation to be provided by UPS or similar provision.

Conditions of Issue of this certificate are printed on page 6.


Qi n et i Q/E E S/E M E S/MED/002/2.0

of 6

Certificate Number

QQ-MED-23/09-01

Certificate of Type Approval - Schedule 2MantaDigital 20" Widescreen ECDIS

The applicant declared that the following units when combined form an operational Marine ShipborneECDIS equipment. The units below have been assessed & tested and satisfactory details of these unitswere included in the technical file.. These units form systems consistent with the Item DescriptionA1/4.30, given in Annex Al of Directive 2008/67/EC .

SYSTEM comprising of:-

MantaDigital Desktop Display Unit (20" Colour LCD)including Trackerball & Keyboard (MDD-A101)

MDD-A30-20-ABAAor MantaDigital Console Display Unit (20" Colour LCD)

MDD-A20-20

*1and MantaDigital

Trackerball & Keyboard

MDD-A101and MantaDigital ECDIS Processing Unit

MDP-A2

*2, 3or MantaDigital Deck mount Pedestal Display Unit (20 " Colour LCD)integrated Processor unit, Trackerball & Keyboard

MDD-A2-20

*2, 3

SOFTWARE:- MantaDigital Core Software (ZM-1816 ECDIS)

Version 4.xx

*4

Seven Cs Presentation Library,

Version 3.4.1

*4 End of List

NOTES:-

1

The console display unit is a panel mounting display for integrating into a ships bridge console.2

This approval is valid for operation in ECDIS and RCDS chart display modes only.Use in ECS mode is reserved for Non-SOLAS vessels or where the ships operating plan agreed by Flag orClass authority allows.

3

This ECDIS system has additional controls for a Track Control Autopilot facility, this function is not covered by thisapproval. The Track Control Autopilot will carry its own Approvals Certificate.

4

This approval remains valid for equipment including subsequent Minor software amendments, as allowed by theN.xx format (xx represents numerals), where written details of any such modifications have been submitted to andaccepted by QinetiQ.

5

This approval recognises the earlier BSH approvals of this ECDIS series with software versions prior to version 4.00certificate BSH/4612/4300391/07 issued 23 February 2007refers.

Technical Characteristics

PARAMETER PROVISION COMMENT

DISPLAYED CHART AREA Chart Size270mm x 270mm

In Route Monitoring Mode20" Widescreen Colour Liquid Crystal Display (LCD).

IEC 61162-1 SERIAL (NMEA)PORTS

Listner 16Talker -16

Conformity to IEC 61162-1:2007.Presence & fault check on messages provide warning status

ANALOGUE SIGNAL PORTS Log & Gyro Pulse log input and Syncro/Stepper Gyro input

RADAR INTERCONNECTIONS 1 Channel Radar Overlay facility tested at QinetiQ Shoebutyness test range.Declared as suitable for operation with Manta & MantaDigitalseries radar.

Back-Up Arrangements Via Ethernet linkto 2nd ECDIS

A second MantaDigital ECDIS running software as listed above mayform a back-up. MantaDigital Chart Radar operating in ECDIS modecould also form an ECDIS Back-up.

TEMPERATURE RANGE Protected& IEC 945 CLASS

Exposed-15°C to+55°C.-25°C to +70°C

-- All

units-- None

POWER SOURCE 110V / 220V AC50-60Hz

Selection between voltage is automatic.Short term operation ( �45s) on power failure to avoid manual re-initialisation to be provided by UPS or similar provision.



QinetiQ/EES/EMES/MED/002/2.0 of 6

Certificate Number

QQ-MED-23/09-01

Certificate of Type Approval - Schedule 3MantaDigital Radar Systems - Back-up processors and alternate displaysThe applicant declared that the following processor units may be used to provide ECDIS Back-up and thedisplays may provide additional or alternate displays screens without the widescreen format. These unitshave been assessed & tested in conjunction with MantaDigital series radar and ECDIS systems, andsatisfactory details are included in the technical files.

PROCESSOR UNITS:-MantaDigital Processor HAP/ECDIS Back-up MDP-A6 *1, 2MantaDigital Processor VDR/ECDIS Back-up MDP-A7 *1, 2MantaDigital Processor S-VDR/ECDIS Back-up MDP-A8 *1, 2MantaDigital HAP/ECDIS Back-up, Display Pedestal 20" LCD MDD-A6-20 *1, 2MantaDigital HAP/ECDIS Back-up, Display Pedestal 26" LCD MDD-A6-26 *1, 2MantaDigital VDR/ECDIS Back-up, Display Pedestal 20" LCD MDD-A7-20 *1, 2MantaDigital VDR/ECDIS Back-up, Display Pedestal 26" LCD MDD-A7-26 *1, 2MantaDigital S-VDR/ECDIS Back-up, Display Pedestal 20" LCD MDD-A8-20 *1, 2MantaDigital S-VDR/ECDIS Back-up, Display Pedestal 26" LCD MDD-A8-26 *1, 2

DISPLAY UNITS:-FSD-A9 *3,4Manta 1700 Console Display

Manta 1700 Desktop Display FSD-A8 *3,4Manta 2000 Console Display FSD-A3 *3,4Manta 2000 Desktop Display FSD-A2 *3,4Manta 2300 Console Display FSD-A6 *3,4Manta 2300 Desktop Display FSD-A5 *3,4

End of List* NOTES:-

1 These units are installed for the first named function but when installed with identical ECDIS software to theprimary ECDIS from schedule 1 or 2 and interconnected via ethernet connections to, may be considered toform an ECDIS Back-Up in conformance with Annex G of IEC 61174. Operation of such dual usage may requireship inspection approval by appropriate Flag or Class authority.

2 The approval status of the primaryfunction (HAP, VDR & 5-VDR) is not covered by this certificate. These unitshave separate approvals for the function involved, refer to appropriate certificates for detail.

3 These additional displays do not have the widescreen display aspect of the MantaDigital displays but canpresent a display that contains all the requirements for IEC 61174 compliance.

4 The resultant chart size with the Manta 1700 display is 270mm x 270mm.





QinetiQ/E E S/ E M E S/M E D/002/2.0

of 6

Certificate Number

QQ-MED-23/09-01

Certificate of Type Approval - Schedule 4MantaDigital Radar Systems - Ancillary and Optional Units

The applicant declared that the following units may be added to the basic ECDIS systems illustrated inschedules 'to 4. These units have been assessed & tested in conjunction with MantaDigital series radarand ECDIS systems, and satisfactory details are included in the technical files.

ANCILLARY UNITS:-MantaDigital Remote Keyboard MDD-A130

FSD-A198 *1Serial Interface Module (provides 8 additional serial ports)MantaDigital Trackerball & pencil trayMantaDigital

TrackerballMantaDigital Control Panel & TrackerballErgonomic Trackerball (Ergopod, right handed)Ergonomic Trackerball (Ergopod, left handed)Dual DNC Unit

MDD-A100MDD-A110MDD-A102NRR-A18NRR-A18-2FSD-A10 *2

Network Audio & Video Control Unit FSD-A13 *2NTI Audio & Video Switch Matrix IT-SM-8t-AV-LCD *2, 3 End of List

* NOTES:-1

This option is an internal module installed insidethe MDP-A1 Or MDP-A9 processor unit.2

These items form a display/control interconnection system and may be used to form an adaptiveworkstation system between units of the MantaDigital radar, SharpEye radar and MantaDigital ECDIS. Theexact configuration enabled bythis system is fixed on commissioning in accordance with an agreed shipsoperating plan.

3

The # is a numeral in the range 2 to 8 and denotes the number of display units which can be included in theinterconnection system.



QinetiQ/E ES/EMES/MED/002/2.0 of 6

Certificate Number

QQ-MED-23/09-01

Certificates of Type ApprovalConditions of Issue

1.

Each Certificate will be used in its entirety and not reproduced in part.

2

This certificate remains valid until the date shown (normally 5 years) unless cancelled or revoked, provided:-

0

the design and manufacture remain unmodified from the specimen tested and recorded in the TechnicalConstruction File;

ii) any conditions contained in the schedule are complied with;

iii) Should the specified regulations or standards be amended during the validity of this certificate, theproduct(s) is/are to be re-approved prior to it/they being placed on board vessels to which the amendedregulations or standards apply;

iv) and, the equipment remains satisfactory in service.

3. The mark of conformity may only be affixed to the equipment listed on this certificate and a manufacturer'sDeclaration of Conformity issued when the production Quality Assurance requirements laid down in Annex B, of theDirective (96/98/EC) is fully complied with and controlled by a written inspection agreement with a Notified Body.

The use of the QinetiQ Notified Body Number (0191) in combination with the Wheelmark implies that themanufacturer is Registered with the QinetiQ Quality Assurance Scheme. A Certificate of Registration is issued to themanufacturer and should be made available on request. The manufacturer is responsible for ensuring thatcertification renewal and periodic surveillance are maintained.

4. USCG Approval Number, A Mutual Recognition Agreement (MRA) on marine equipment exists between theEuropean Commission and the US Coastguard but only applies to equipment types included in the listing of marineequipment annexed to the MRA. For included equipment a USCG Approval number may be issued. This can befound under the MED certificate number on the first page and should be used on the main identity label of theequipment. Radio and Radar equipment continues to need separate or additional approval by the USA FCC.

5. This certificate does not confer any approval status to this equipment other than defined by, and tested accordingto the specifications listed on Page 1.

6. The labeling requirements of IMO Resolution A694(17) shall be met. Descriptions of each unit of apparatus formingpart of the equipment will be as given on this Certificate. Each unit of equipment will be marked with the minimumsafe distance at which it should be mounted from a standard and steering magnetic compass.

7. No unit of apparatus shall be advertised or labeled as "approved" or "certified" on behalf of the Maritime andCoastguard Agency, the Department of Transport or the QinetiQ Group in any sense other than that it is a type thathas been assessed as satisfactory against the specification;

8

The manufacturer must advise QinetiQ of any intended changes to the design or production of the equipmentwhich might affect the equipment performance.

9 Minor Modifications to the equipment will be considered on a case-by-case basis. QinetiQ will review any factorytest results, in consultation if necessary, with the test facility that conducted the original Type Approval testing onthe equipment. QinetiQ will advise the manufacturer if any further testing is required to maintain validcertification.

10 If an equipment manufacturer wishes to have the type approved equipment designated under alternative names(e.g. agent/distributor's name and model number), a separate application should be completed and sent to QinetiQ.

QinetiQ LtdMarine Approval and Testing ServiceCody Technology Park, Room 1005/A5Ively Road, FarnboroughHants, GU14OLXUnited Kingdom

Qi n et i Q/ E E S/E M E 5/MED/002/2.0

of 6

QinetiQ - Aegean · PDF fileRADAR INTERCONNECTIONS 1 Channel Radar Overlay facility tested at...

Documents

Transcript of QinetiQ - Aegean · PDF fileRADAR INTERCONNECTIONS 1 Channel Radar Overlay facility tested at...