PVENG
-
Upload
kehinde-adebayo -
Category
Documents
-
view
84 -
download
5
Transcript of PVENG
Home FEA ASME Calcs CRN Solid Model Burst Test Samples About PVEng
Pressure Vessel Code - Audit Vessel
Tel: 519-880-9808Email: [email protected]
ASME Code CalculationPressure Vessel Engineering Ltd. has over 10 years of ASME code design experience. We have completed thousands ofprojects ranging from small fittings to large reactors.We hold the following codes in house, along with many others:
Boiler & Pressure Vessel CodeASME I - Construction of Power BoilersASME II - MaterialsASME III - Construction of Nuclear Facility ComponentsASME IV - Construction of Heating BoilersASME VIII-1 / VIII-2 - Construction of Pressure Vessels
Piping CodeASME B31.1 Power PipingASME B31.3 Process PipingASME B31.4 Hydrocarbon PipingASME B31.5 Refrigeration PipingASME B31.8 Gas Transmission PipingASME B31.11 Slurry Piping
Valves, Flanges & FittingsASME B16.5 Flange & Flange FittingsASME B16.47 Large Steel FlangesASME B16.1 Grey Iron Flange & Flange FittingsASME B16.3 Malleable Iron Flange & Flange FittingsASME B16.11 Forged FittingsMSS-SP-67 Butterfly Valves
Pressure Vessel Engineering Ltd. uses both APV (Advanced Pressure Vessel) and PVElite commercial software coupledwith our own unique spreadsheets to complete ASME code calculations. We can review existing designs or act as yourin-house engineering department.Below are several samples which are representative of ASME jobs we have completed. All of our sample jobs can be viewedhere.For quotation and general inquires please contact:
File: Samples/Sample2Last Updated: June 16, 2010
Laurence Brundrett
A Standard Audit Vessel?This example shows ASME code calculations for a simple vessel.Calculations are completed with both our commercial softwarepackages (APV & PVElite) as well as with our own in-housespreadsheets. A drawing typical of what PVEng provides is also
ASME Calculations http://www.pveng.com/ASME/ASMEIntro.php
1 of 3 11/08/2011 09:43
Pressure Vessel Code - Horizontal Retention Vessel
Pressure Vessel Code - Simple Vertical Vessel
Pressure Vessel Code - Vessel with a Large Opening
Pressure Vessel Code - Tower
available for download. We have helped several of our customerscomplete ASME "U" stamp audits with simple vessels similar to this.
More...
File: Samples/Sample 3Last Updated: June 16, 2010
Laurence Brundrett
This example shows ASME code calculations completed for ahorizontal vessel. As ASME does not provide a calculation method forthe support saddles a "Zick" analysis is completed. This examplediscusses the effects of saddles on a design and provides an examplesaddle calculation.
More...
File: Sample 4Last Updated: June 16, 2010
By: LB
This example shows ASME code calculations for a vertical vessel.Pressure Vessel Engineering Ltd., regularly completes ASME codereview on vessels similar to this. This example includes leg supportcalculations accounting for seismic loadings as well as review of a padflange.
More...
File: Sample 5Last Updated: June 16, 2010
LB
This example shows calculations completed for some difficult to designitems such as large nozzles, swing bolt covers and lugs, conediscontinuities, and ferrules. Pressure Vessel Engineering Ltd. hasextensive experience analyzing these and other obscure items. We havecompleted thousands of projects with features such as this, many usedfor Canadian or National Board registration.
More...
File: PVE-3602Last Updated: Dec. 11, 2009
LB
This example shows a vertical vessel with several features associated
ASME Calculations http://www.pveng.com/ASME/ASMEIntro.php
2 of 3 11/08/2011 09:43
Heat Exchanger
Piping System
Alterations & Used Vessels - Addition of a Nozzle
with this type of design. ASME code calculations addressing skirt,cone, and seismic and wind conditions are shown.
More...
File: PVE-Sample 11Last Updated: April 2009
CM
Pressure Vessel Engineering has extensive experience completing codecalculations (ASME & TEMA) for plate as well as shell and tube heatexchangers. This example shows a heat exchanger calculated inaccordance with ASME VIII-1 UHX for the seven possible load cases.
More...
File: PVE-Sample12Last Updated: Oct. 17, 2008
JL
PVEng has completed ASME code calculations for hundreds of pipingsystems. Canadian registration (CRN) is typically required for pipingsystems operating above 15 psi. Registration of piping can be confusingas the requirements vary from province to province and are not welldocumented. This example details a simple system calculations anddrawings. We would be happy to discuss your requirements and helpguide you through the registration process.
More...
File: Samples/Sample 1Last Updated: June 16, 2010
Laurence Brundrett
This example shows calculations completed for the addition of a nozzleto an existing vessel. While the calculations are very simple theregistration requirements of a used vessel can be complex. Calculationsmust be completed in accordance with the original code ofconstruction. Ultrasonic testing may also be required to confirm thecurrent condition of the vessel.
More...
(c)2011 Pressure Vessel Engineering Ltd.
ASME Calculations http://www.pveng.com/ASME/ASMEIntro.php
3 of 3 11/08/2011 09:43