Roller ShutterRoller ShutterRoller Shutter

Roller Shutter Roller Shutter Roller Shutter Roller Shutter

1350

1550

2900

3000 1950 35002500 1000 2500 1250 3400 1400

2900

6015

2900

Extent of Extension

8344

PROPOSED EAST ELEVATIONSCALE 1:50 @ A1

PROPOSED SOUTH ELEVATIONSCALE 1:50 @ A1

PROPOSED NORTH ELEVATIONSCALE 1:50 @ A1

182 1348 2206 1348 2393 1348 1115 4997 1015

9940

Status

Drawing no Rev

Drawing

Project

Rev Date Amendment

A1

Scale @ A1

NOTES:

Drawn Checked AuthorisedDate

All dimensions to be verified on site and any discrepancies reported in

writing to Project Manager before proceeding with work. All

dimensions should read from those values stated in text on the

drawing.

Drwn Chkd

Client

Georgians FC

Cromwell Ave

Stockport

Proposed Elevations

1:100 24.05.19 AT - -

PLANNING

D0002 -

WC

WC

WCPLANT

ROOM

SHOWERS

SHOWERS

CHANGING

ROOMS

CHANGING

ROOMS

12

00

12

00

12

00

24

00

22

80

12

00

12

00

22

80

OFFICIALS

CHANGING

ROOMSHOWER

AREA OUT

OF SCOPE

Proposed Ground Floor -Changing Room Extension

7120

A-A

NOTES 1. FIRST ANGLE PROJECTION. 2. DIMENSIONS SHOWN IN BRACKETS THUS (25) ARE REF. DIMENSIONS ONLY. 3. REMOVE ALL BURRS & SHARP EDGES. 4. DO NOT SCALE IF IN DOUBT ASK. 5. WELDING SYMBOLS ARE TO BS EN 24063 & BS EN 22553 6. ALL STANDARDS & SPECIFICATIONS ARE TO BE TO THE LATEST REVISIONS. 7. FILLET WELDS TO BE TO WELD PROCEDURE No. 031W. 8. MATERIAL: CHS TO BS EN 10210 GRD S275 WITH A TENSILE STRENGTH OF 430N/mm² CHS TO BE EN 10210 GRD S355 WITH A TENSILE STRENGTH OF 490N/mm². PLATE FROM M.S TO BSEN 10025 GRD S275. PLATE 25mm THICK AND OVER TO BE CHARPY TEST VALUE OF 27J (MIN) AT -15ºC. 9. FINISH HOT DIP GALV TO BS EN ISO 1461. 10. FOR DETAIL OF BASE SEE DRG NO RL201/97 SERIES.

HL250D15 MAST

Drg. No.

Client

TitleDrawn

Checked

Date Sales order No.

General tolerences unless stated otherwise:-

0mm-500mm-------- �

501mm-1000mm--- �

Above----------------- �

Copyright Strictly Reserved

Abacus Lighting Ltd.

© 2006

Patent No.

Reg. Design No.

STANDARD COMPONENT

HL250D15/4/AL5760 28/11/2006

A.BOOTH

L DYE

Not to scale

AA

150

00

-050

0+

N

OM

INA

L H

EIG

HT

735

C.L. OF PIVOT

GEAR CUBICLEIF REQUIRED.

400 CRS

4 NO. SLOTS 85x36 TO ENABLE ±5°ROTATION FOR M30x800LGHOLDING DOWN BOLTS.

11. FOUNDATION BOLTS ARE TYPE 3 TO DRG NO C201/42 12.FOR DETAILS OF SHAFTS SEE DRG NO RL201/41/23. 13.WEIGHT OF SHAFTS AS FOLLOWS OCT2502S15 23KG OCT250S12 116KG BASE ASSY 236KG. 14. SHAFT OVERLAPS:- SHAFT MIN DESIGN NO OVERLAP OVERLAP OCT2502S15 215 636 TO OCT250S12 OCT250S12 425 759 TO BASE

OC

T2

50

S12

OC

T2

50

2S

15