PRODUCTO DIEMAKERS SUPPLIES LIMITED · producto diemakers supplies limited serving the canadian...
Transcript of PRODUCTO DIEMAKERS SUPPLIES LIMITED · producto diemakers supplies limited serving the canadian...
PRODUCTO DIEMAKERS SUPPLIES LIMITEDSERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964
®
SPRINGS
• SPECIAL/CUSTOM SPRINGS
• DIE SPRINGS
• D-LINE SPRINGS
• COMPRESSION SPRINGS
• EXTENSION SPRINGS
• EASY SPRING SELECTOR
• GAS SPRINGS
• SPRING ASSORTMENTS
• REPLACEMENT SPRINGS
• DISC SPRINGS
ACCESSORIES• ALLENAIR
• ENERPAC
• RING PRECISION
• TRANSFER SCREWS
• TRANSFER PUNCHES
• VLIER SPRING LOADED PLUNGERS
• VIBRA-SYSTEMS VIBRATION MOUNTS
• URETHANE PRODUCTS
• DAC
• WEICON TECHNICAL SPRAYS
www.productodiemakers.com [email protected]
ONTARIO • TEL: (905) 856-9990 FAX: (905) 856-9887 TOLL FREE: 1-866-562-0555 641 Chrislea Road, Unit #4, Vaughan, ON L4L 8A3
QUEBEC • TEL: (450) 430-5082 FAX: (450) 430-1022 TOLL FREE: 1-866-508-5082 4486 Boulevard de la Grande Allee, Boisbriand, QC J7H 1R9
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 19642
®
ABOUT
We Have You Covered For All Your Die Supplies in Canada… Serving the Manufacturing Industry Since 1964
ABOUT US
SPRINGS INDEX SPECIAL/CUSTOM SPRINGS ............................................................................................................................................ 3DIE SPRINGS INCH SERIES .........................................................................................................................................4 - 7ISO D-LINE SPRINGS .....................................................................................................................................................8 - 11COMPRESSION SPRINGS SERIES 020 ........................................................................................................................ 12EXTENSION SPRINGS SERIES 020............................................................................................................................... 13EASY SPRING SELECTOR GUIDE (Compression & Extension) ..................................................................14 - 18SPRING BOXED ASSORTMENTS ................................................................................................................................... 19REPLACEMENT SPRINGS #750, #400, #250 ..................................................................................................20 - 21GAS SPRINGS ....................................................................................................................................................................... 22DISC SPRINGS ............................................................................................................................................................. 23 - 25ACCESSORIESALLENAIR ..................................................................................................................................................................... 26 - 27ENERPAC ............................................................................................................................................................................... 28RING PRECISION ................................................................................................................................................................. 28TRANSFER SCREWS ......................................................................................................................................................... 29TRANSFER PUNCHES ....................................................................................................................................................... 29VLIER SPRING LOADED PLUNGERS...................................................................................................................30 - 31VIBRA-SYSTEMS VIBRATION MOUNTS ..................................................................................................................... 32URETHANE ............................................................................................................................................................................ 33DAC ..........................................................................................................................................................................................34WEICON .................................................................................................................................................................................34
QUALITY PRODUCTS • SUPERIOR CUSTOMER SERVICE • QUICK SHIPPINGRepresenting companies throughout the world permits PRODUCTO Diemakers to offer you a quality product for a
competitive price. We stock most items listed in our catalogue, with same day shipping on most stock items.
Our product lines include Springs, Hydraulics, Pneumatics, Transfer Punches, Transfer Screws, Lubricants and Adhesives, Spring Loaded Devices, Urethane Products, Fluid Power, Precision Components and Industrial Supplies.
PRODUCTO Die Springs are manufactured under rigid quality control, inspection and testing to ensure long service life.Our Die Springs are color coded by work range, to simplify selection specification and in plant identification. Die spring inventories assure fast, off-the-shelf delivery.
CUSTOM/SPECIAL Die Springs are our specialty. Just fill out the information on the next page and we will get back to you with a quote.
Can’t find what you’re looking for, just give us a call. We couldn’t fit everything we carry in the catalogue. Additional information can be found on our website: www.productodiemakers.com or give our customer service department a call.
We look forward to serving you with all your Diemakers Supplies
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 3
®
PRODUCTO CAN ASSIST YOU IN MAKING ANY SIZE OR TYPE OF SPRING WE ARE THE SPRING SPECIALISTS!
BODY LENGTH
(O.D.)OUTSIDE
DIAMETER
WIRE DIAMETER
LENGTH INSIDE LOOPS
OVERALL LENGTH
FREE LENGTH
PITCH DISTANCE BETWEEN COILS
(I.D.)INSIDE
DIAMETER
(O.D.)OUTSIDE
DIAMETER
WIREDIAMETER
1 2 3 4 5 6 7 8
LENGTH OF LEG NUMBEROF COILS
(O.D
.)
OUTSID
E
DIAMETE
R
WIRE DIAMETER
10 2 3 4 5 6 7
IMPORTANTPlease photocopy this page.
Supply us with complete specifications, a drawing and a sample.
Date: _________________________________________________
Company Name: ______________________________________
Contact: _____________________________________________
Position: ______________________________________________
Phone: _______________________________________________
Fax: __________________________________________________
E-mail: _______________________________________________
Quantity: ___________ Date Required: __________________
Dimensions/Type: Inch Metric
Compression Extension Torsion Other
Description: __________________________________________
______________________________________________________
Inside Diameter: __________ Outside Diameter: ___________
Fits in Hole Size: _________ Fits over a Rod Size: ________
______ Lbs. Load at ______ Inches. Free Length: __________
Total # of Coils: __________ Solid Height: ________________
Wire Size: _______________ Type of Ends: ________________
Pitch: __________________ R/L Wind: ___________________
If Extension – Length of Spring Inside of Hooks: ___________
If Extension – Body Length: _____________________________
Finish: ________________________________________________
Type of Material if Known: ______________________________
Working Environment: __________________________________
EXTENSION SPRINGS
COMPRESSION SPRINGS
TORSION SPRINGS
USE THIS INCH SCALE TO ASSIST WITH APPROXIMATE MEASUREMENTS
TYPES OF ENDS USEDON EXTENSION SPRINGS
STANDARD TYPES OF ENDS USED ON COMPRESSION SPRINGS
A
DB
FULL LOOP FROM SIDE
MACHINE HOOKC DOUBLE FULL
LOOP
Z SQUAREDEND X SQUARED END
GROUND Y PLAIN END W PLAIN END
GROUND
FULL LOOPFROM CENTER
GLONG ROUND END
HOOK OVER CENTERFSINGLE FULL LOOP
CENTEREDEDOUBLE TWISTED FULL
LOOP OVER CENTER
CUSTOM SPRINGS QUOTATION REQUEST
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 19644
®
PRODUCTO (MP) MEDIUM PRESSURE DIE SPRINGS - COLOUR CODED BLUE
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 40% of free length
Load at 1/10” (lb.)
3/8 x 3/16 x
Wire Size.039 x .070
1 MP02 200 24.0 6.0
1 1/4 MP02A 200 27.0 5.4
1 1/2 MP03 100 24.0 4.0
1 3/4 MP03A 100 23.8 3.4
2 MP04 100 22.4 2.8
2 1/2 MP05 100 24.0 2.4
3 MP06 100 25.2 2.1
12 MP024 50 28.8 0.6
1/2 x 9/32 x
Wire Size.052 x .093
1 MP12 100 44.0 11.0
1 1/4 MP12A 100 41.0 8.2
1 1/2 MP13 100 40.8 6.8
1 3/4 MP13A 100 42.0 6.0
2 MP14 100 44.0 5.5
2 1/2 MP15 50 45.0 4.5
3 MP16 50 42.0 3.5
3 1/2 MP17 50 42.0 3.0
4 1/2 MP19 50 45.0 2.5
5 1/2 MP111 50 46.2 2.1
6 1/2 MP113 50 36.4 1.4
7 1/2 MP115 50 36.0 1.2
12 MP124 50 33.6 0.7
5/8 x 11/32 x
Wire Size.069 x .109
1 MP22 100 65.6 16.4
1 1/4 MP22A 100 64.0 12.8
1 1/2 MP23 50 64.8 10.8
1 3/4 MP23A 50 67.2 9.6
2 MP24 50 70.4 8.8
2 1/2 MP25 50 60.0 6.0
3 MP26 50 67.2 5.6
3 1/2 MP27 50 67.2 4.8
4 MP28 50 70.4 4.4
12 MP224 50 76.8 1.6
3/4 x 3/8 x
Wire Size.075 x .165
1 MP32 50 124.8 31.2
1 1/4 MP32A 50 128.0 25.6
1 1/2 MP33 50 120.0 20.0
1 3/4 MP33A 50 123.2 17.6
2 MP34 50 115.2 14.4
2 1/2 MP35 50 120.0 12.0
3 MP36 50 115.2 9.6
3 1/2 MP37 50 112.0 8.0
4 MP38 50 115.2 7.2
4 1/2 MP39 50 115.2 6.4
5 MP310 50 120.0 6.0
5 1/2 MP311 50 121.0 5.5
6 MP312 50 120.0 5.0
6 1/2 MP313 50 117.0 4.5
7 1/2 MP315 50 114.0 3.8
12 MP324 50 115.2 2.4
1 x 1/2 x
Wire Size.100 x .215
1 MP42 50 220.0 55.0
1 1/4 MP42A 50 225.0 45.0
1 1/2 MP43 50 210.0 35.0
1 3/4 MP43A 50 210.0 30.0
2 MP44 50 208.0 26.0
2 1/2 MP45 50 200.0 20.0
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 40% of free length
Load at 1/10” (lb.)
1 x 1/2 x
Wire Size.100 x .215
3 MP46 25 198.0 16.5
3 1/2 MP47 25 210.0 15.0
4 MP48 25 192.0 12.0
4 1/2 MP49 25 187.2 10.4
5 MP410 25 192.0 9.6
5 1/2 MP411 25 193.6 8.8
6 MP412 25 192.0 8.0
7 MP414 25 201.6 7.2
8 MP416 25 192.0 6.0
12 MP424 25 192.0 4.0
1 1/4 x 5/8 x
Wire Size.115 x .285
1 1/2 MP53 50 297.6 49.6
1 3/4 MP53A 50 296.8 42.4
2 MP54 50 281.6 35.2
2 1/2 MP55 25 288.0 28.8
3 MP56 25 288.0 24.0
3 1/2 MP57 25 280.0 20.0
4 MP58 25 281.6 17.6
4 1/2 MP59 25 288.0 16.0
5 MP510 25 272.0 13.6
5 1/2 MP511 25 281.6 12.8
6 MP512 25 288.0 12.0
7 MP514 25 291.2 10.4
8 MP516 25 281.6 8.8
10 MP520 25 288.0 7.2
12 MP524 25 288.0 6.0
1 1/2 x 3/4 x
Wire Size.135 x .345
2 MP64 25 424.0 53.0
2 1/2 MP65 25 450.0 45.0
3 MP66 25 432.0 36.0
3 1/2 MP67 25 420.0 30.0
4 MP68 25 432.0 27.0
4 1/2 MP69 25 414.0 23.0
5 MP610 25 420.0 21.0
5 1/2 MP611 25 407.0 18.5
6 MP612 25 408.0 17.0
7 MP614 25 406.0 14.5
8 MP616 25 409.6 12.8
10 MP620 25 400.0 10.0
12 MP624 25 384.0 8.0
2 x 1 x
Wire Size.195 x .468
2 1/2 MP85 25 1000.0 100.0
3 MP86 25 996.0 83.0
3 1/2 MP87 25 907.2 64.8
4 MP88 25 960.0 60.0
4 1/2 MP89 25 954.0 53.0
5 MP810 25 940.0 47.0
5 1/2 MP811 25 862.4 39.2
6 MP812 20 936.0 39.0
7 MP814 20 873.6 31.2
8 MP816 10 912.0 28.5
10 MP820 10 832.0 20.8
12 MP824 10 840.0 17.5
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
*Maximum Deflection(50% of free length)
For Long Life (35% of free length)
Maximum Operation Def.(40% of free length)
For Optimum Life(25% of free length)
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 5
®
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 30% of free length
Load at 1/10” (lb.)
3/8 x 3/16 x
Wire Size.046 x .073
1 MHP02 200 27.0 9.0
1 1/4 MHP02A 200 27.4 7.3
1 1/2 MHP03 100 30.2 6.7
1 3/4 MHP03A 100 30.5 5.8
2 MHP04 100 30.0 5.0
2 1/2 MHP05 100 31.5 4.2
3 MHP06 100 27.0 3.0
12 MHP024 50 32.4 0.9
1/2 x 9/32 x
Wire Size.061 x .093
1 MHP12 100 50.4 16.8
1 1/4 MHP12A 100 48.8 13.0
1 1/2 MHP13 100 42.8 9.5
1 3/4 MHP13A 100 44.6 8.5
2 MHP14 100 45.0 7.5
2 1/2 MHP15 50 45.0 6.0
3 MHP16 50 51.3 5.7
3 1/2 MHP17 50 42.0 4.0
12 MHP124 50 43.2 1.2
5/8 x 11/32 x
Wire Size.081 x .123
1 MHP22 100 90.0 30.0
1 1/4 MHP22A 100 80.6 21.5
1 1/2 MHP23 50 85.5 19.0
1 3/4 MHP23A 50 88.2 16.8
2 MHP24 50 88.8 14.8
2 1/2 MHP25 50 86.3 11.5
3 MHP26 50 90.0 10.0
3 1/2 MHP27 50 89.3 8.5
4 MHP28 50 91.2 7.6
12 MHP224 50 97.2 2.7
3/4 x 3/8 x
Wire Size.093 x .156
1 MHP32 50 150.0 50.0
1 1/4 MHP32A 50 142.5 38.0
1 1/2 MHP33 50 144.0 32.0
1 3/4 MHP33A 50 151.2 28.8
2 MHP34 50 148.8 24.8
2 1/2 MHP35 50 144.0 19.2
3 MHP36 50 129.6 14.4
3 1/2 MHP37 50 134.4 12.8
4 MHP38 50 144.0 12.0
4 1/2 MHP39 50 151.2 11.2
5 MHP310 50 135.0 9.0
5 1/2 MHP311 50 132.0 8.0
6 MHP312 50 135.0 7.5
12 MHP324 50 129.6 3.6
1 x 1/2 x
Wire Size.115 x .218
1 MHP42 50 228.0 76.0
1 1/4 MHP42A 50 234.0 62.4
1 1/2 MHP43 50 223.2 49.6
1 3/4 MHP43A 50 231.0 44.0
2 MHP44 50 240.0 40.0
2 1/2 MHP45 50 232.5 31.0
3 MHP46 25 225.0 25.0
3 1/2 MHP47 25 226.8 21.6
4 MHP48 25 220.8 18.4
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 30% of free length
Load at 1/10” (lb.)
1 x 1/2 x
Wire Size.115 x .218
4 1/2 MHP49 25 229.5 17.0
5 MHP410 25 216.0 14.4
5 1/2 MHP411 25 211.2 12.8
6 MHP412 25 216.0 12.0
7 MHP414 25 210.0 10.0
8 MHP416 25 211.2 8.8
12 MHP424 25 223.2 6.2
1 1/4 x 5/8 x
Wire Size.156 x .281
1 1/2 MHP53 50 514.8 114.4
1 3/4 MHP53A 50 529.2 100.8
2 MHP54 50 518.4 86.4
2 1/2 MHP55 25 468.0 62.4
3 MHP56 25 460.8 51.2
3 1/2 MHP57 25 462.0 44.0
4 MHP58 25 441.6 36.8
4 1/2 MHP59 25 432.0 32.0
5 MHP510 25 435.0 29.0
5 1/2 MHP511 25 435.6 26.4
6 MHP512 25 450.0 25.0
7 MHP514 25 420.0 20.0
8 MHP516 25 441.6 18.4
10 MHP520 25 435.0 14.5
12 MHP524 25 446.4 12.4
1 1/2 x 3/4 x
Wire Size.187 x .312
2 MHP64 25 648.0 108.0
2 1/2 MHP65 25 642.0 85.6
3 MHP66 25 561.6 62.4
3 1/2 MHP67 25 554.4 52.8
4 MHP68 25 576.0 48.0
4 1/2 MHP69 25 583.2 43.2
5 MHP610 25 552.0 36.8
5 1/2 MHP611 25 567.6 34.4
6 MHP612 25 547.2 30.4
7 MHP614 25 554.4 26.4
8 MHP616 25 528.0 22.0
10 MHP620 25 528.0 17.6
12 MHP624 20 518.4 14.4
2 x 1 x
Wire Size.225 x .437
2 1/2 MHP85 25 888.0 118.4
3 MHP86 25 864.0 96.0
3 1/2 MHP87 25 840.0 80.0
4 MHP88 25 796.8 66.4
4 1/2 MHP89 25 810.0 60.0
5 MHP810 25 840.0 56.0
5 1/2 MHP811 25 831.6 50.4
6 MHP812 20 849.6 47.2
7 MHP814 20 840.0 40.0
8 MHP816 10 844.8 35.2
10 MHP820 10 780.8 26.0
12 MHP824 10 806.4 22.4
PRODUCTO (MHP) MEDIUM HIGH PRESSURE DIE SPRINGS - COLOUR CODED RED
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
*Maximum Deflection(37% of free length)
For Long Life (25% of free length)
Maximum Operation Def. (30% of free length)
For Optimum Life(20% of free length)
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 19646
®
PRODUCTO (HP) HIGH PRESSURE DIE SPRINGS - COLOUR CODED GOLD
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
*Maximum Deflection(30% of free length)
For Long Life (20% of free length)
Maximum Operation Def. (25% of free length)
For Optimum Life(15% of free length)
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 25% of free length
Load at 1/10” (lb.)
3/8 x 3/16 x
Wire Size.054 x .072
1 HP02 200 27.5 11.0
1 1/4 HP02A 200 30.6 9.8
1 1/2 HP03 100 30.0 8.0
1 3/4 HP03A 100 36.8 8.4
2 HP04 100 36.0 7.2
2 1/2 HP05 100 34.4 5.5
3 HP06 100 31.5 4.2
12 HP024 50 36.0 1.2
1/2 x 9/32 x
Wire Size.070 x .093
1 HP12 100 59.0 23.6
1 1/4 HP12A 100 58.1 18.6
1 1/2 HP13 100 58.1 15.5
1 3/4 HP13A 100 60.4 13.8
2 HP14 100 55.0 11.0
2 1/2 HP15 50 52.5 8.4
3 HP16 50 55.5 7.4
3 1/2 HP17 50 52.5 6.0
12 HP124 50 48.0 1.6
5/8 x 11/32 x
Wire Size.093 x .125
1 HP22 100 106.0 42.4
1 1/4 HP22A 100 92.5 29.6
1 1/2 HP23 50 102.0 27.2
1 3/4 HP23A 50 105.0 24.0
2 HP24 50 104.0 20.8
2 1/2 HP25 50 106.3 17.0
3 HP26 50 108.0 14.4
3 1/2 HP27 50 106.8 12.2
4 HP28 50 108.0 10.8
12 HP224 50 90.0 3.0
3/4 x 3/8 x
Wire Size.125 x .165
1 HP32 50 270.0 108.0
1 1/4 HP32A 50 275.0 88.0
1 1/2 HP33 50 246.0 65.6
1 3/4 HP33A 50 262.5 60.0
2 HP34 50 248.0 49.6
2 1/2 HP35 50 250.0 40.0
3 HP36 50 255.0 34.0
3 1/2 HP37 50 245.0 28.0
4 HP38 50 250.0 25.0
4 1/2 HP39 50 247.5 22.0
5 HP310 50 243.8 19.5
5 1/2 HP311 50 233.8 17.0
6 HP312 50 240.0 16.0
12 HP324 50 240.0 8.0
1 x 1/2 x
Wire Size.158 x .225
1 HP42 50 520.0 208.0
1 1/4 HP42A 50 535.0 171.2
1 1/2 HP43 50 444.0 118.4
1 3/4 HP43A 50 455.0 104.0
2 HP44 50 450.0 90.0
2 1/2 HP45 50 425.0 68.0
3 HP46 25 408.0 54.4
3 1/2 HP47 25 399.0 45.6
4 HP48 25 400.0 40.0
4 1/2 HP49 25 396.0 35.2
5 HP410 25 390.0 31.2
5 1/2 HP411 25 396.0 28.8
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 25% of free length
Load at 1/10” (lb.)
1 x 1/2 x
Wire Size.158 x .225
6 HP412 25 384.0 25.6
7 HP414 25 392.0 22.4
8 HP416 25 384.0 19.2
12 HP424 25 360.0 12.0
1 1/4 x 5/8 x
Wire Size.200 x .295
1 1/2 HP53 50 795.0 212.0
1 3/4 HP53A 50 794.5 181.6
2 HP54 50 748.0 149.6
2 1/2 HP55 25 735.0 117.6
3 HP56 25 714.0 95.2
3 1/2 HP57 25 658.0 75.2
4 HP58 25 664.0 66.4
4 1/2 HP59 25 657.0 58.4
5 HP510 25 662.5 53.0
5 1/2 HP511 25 649.0 47.2
6 HP512 25 636.0 42.4
7 HP514 25 644.0 36.8
8 HP516 25 656.0 32.8
10 HP520 25 640.0 25.6
12 HP524 20 624.0 20.8
1 1/2 x 3/4 x
Wire Size.225 X .350
2 HP64 25 952.0 190.4
2 1/2 HP65 25 968.8 155.0
3 HP66 25 975.0 130.0
3 1/2 HP67 25 931.0 106.4
4 HP68 25 912.0 91.2
4 1/2 HP69 25 882.0 78.4
5 HP610 25 890.0 71.2
5 1/2 HP611 25 880.0 64.0
6 HP612 25 876.0 58.4
7 HP614 25 868.0 49.6
8 HP616 25 864.0 43.2
10 HP620 20 860.0 34.4
12 HP624 15 864.0 28.8
2 x 1 x
Wire Size.270 x .470
2 1/2 HP85 25 1625.0 260.0
3 HP86 25 1500.0 200.0
3 1/2 HP87 25 1487.5 170.0
4 HP88 25 1500.0 150.0
4 1/2 HP89 25 1350.0 120.0
5 HP810 20 1375.0 110.0
5 1/2 HP811 20 1375.0 100.0
6 HP812 15 1410.0 94.0
7 HP814 15 1435.0 82.0
8 HP816 10 1460.0 73.0
10 HP820 10 1375.0 55.0
12 HP824 10 1260.0 42.0
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 7
®
PRODUCTO (XHP) EXTRA HIGH PRESSURE DIE SPRINGS - COLOUR CODED GREEN
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
*Maximum Deflection(25% of free length)
For Long Life (17% of free length)
Maximum Operation Def. (20% of free length)
For Optimum Life(15% of free length)
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 20% of free length
Load at 1/10” (lb.)
3/8 x 3/16 x
Wire Size.059 x .080
1 XHP02 200 44.0 22.0
1 1/4 XHP02A 200 40.0 16.0
1 1/2 XHP03 100 37.5 12.5
1 3/4 XHP03A 100 40.3 11.2
2 XHP04 100 36.0 9.0
2 1/2 XHP05 100 35.0 7.0
3 XHP06 100 39.0 6.5
12 XHP024 50 36.0 1.5
1/2 x 9/32 x
Wire Size.084 x .097
1 XHP12 100 64.0 32.0
1 1/4 XHP12A 100 60.0 24.0
1 1/2 XHP13 100 60.0 20.0
1 3/4 XHP13A 100 59.5 17.0
2 XHP14 100 56.0 14.0
2 1/2 XHP15 50 57.5 11.5
3 XHP16 50 54.0 9.0
3 1/2 XHP17 50 56.0 8.0
12 XHP124 50 60.0 2.5
5/8 x 11/32 x
Wire Size.110 x .126
1 XHP22 100 126.0 63.0
1 1/4 XHP22A 100 117.5 47.0
1 1/2 XHP23 50 114.0 38.0
1 3/4 XHP23A 50 112.0 32.0
2 XHP24 50 116.0 29.0
2 1/2 XHP25 50 110.0 22.0
3 XHP26 50 114.0 19.0
3 1/2 XHP27 50 112.0 16.0
4 XHP28 50 108.0 13.5
12 XHP224 50 108.0 4.5
3/4 x 3/8 x
Wire Size.135 x .165
1 XHP32 50 280.0 140.0
1 1/4 XHP32A 50 275.0 110.0
1 1/2 XHP33 50 267.0 89.0
1 3/4 XHP33A 50 262.5 75.0
2 XHP34 50 272.0 68.0
2 1/2 XHP35 50 250.0 50.0
3 XHP36 50 243.0 40.5
3 1/2 XHP37 50 241.5 34.5
4 XHP38 50 240.0 30.0
4 1/2 XHP39 50 238.5 26.5
5 XHP310 50 235.0 23.5
5 1/2 XHP311 50 236.5 21.5
6 XHP312 50 234.0 19.5
12 XHP324 50 228.0 9.5
1 x 1/2 x
Wire Size.188 x .225
1 1/2 XHP43 50 480.0 160.0
2 XHP44 50 464.0 116.0
2 1/2 XHP45 50 448.0 89.6
3 XHP46 25 441.6 73.6
3 1/2 XHP47 25 436.8 62.4
4 XHP48 25 441.6 55.2
4 1/2 XHP49 25 439.2 48.8
5 XHP410 25 432.0 43.2
6 XHP412 25 432.0 36.0
12 XHP424 25 422.4 17.6
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length Producto Part#
Box Qty
Max. Oper Def 20% of free length
Load at 1/10” (lb.)
1 1/4 x 5/8 x
Wire Size.225 x .295
2 XHP54 50 768.0 192.0
2 1/2 XHP55 25 720.0 144.0
3 XHP56 25 710.4 118.4
3 1/2 XHP57 25 705.6 100.8
4 XHP58 25 672.0 84.0
4 1/2 XHP59 25 705.6 78.4
5 XHP510 25 680.0 68.0
6 XHP512 25 672.0 56.0
8 XHP516 25 665.6 41.6
10 XHP520 25 672.0 33.6
12 XHP524 20 633.6 26.4
1 1/2 x 3/4 x
Wire Size.300 x .350
2 XHP64 25 1504.0 376.0
2 1/2 XHP65 25 1472.0 294.4
3 XHP66 25 1387.2 231.2
3 1/2 XHP67 25 1372.0 196.0
4 XHP68 25 1369.6 171.2
4 1/2 XHP69 25 1332.0 148.0
5 XHP610 25 1360.0 136.0
6 XHP612 25 1324.8 110.4
8 XHP616 20 1292.8 80.8
10 XHP620 15 1344.0 67.2
12 XHP624 10 1305.6 54.4
2 x 1 x
Wire Size.365 x .460
2 1/2 XHP85 25 1908.0 381.6
3 XHP86 25 1872.0 312.0
3 1/2 XHP87 25 1780.8 254.4
4 XHP88 20 1760.0 220.0
4 1/2 XHP89 20 1699.2 188.8
5 XHP810 15 1728.0 172.8
6 XHP812 15 1699.2 141.6
8 XHP816 10 1600.0 100.0
10 XHP820 10 1680.0 84.0
12 XHP824 10 1708.8 71.2
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 19648
®
SPRINGSISO D-LINE GREEN LIGHT DUTY
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Load @ 40% of free length
Spring Rate per 1/10 inch Def.
3/8 x 3/16 x 1 303104D 50 27.0 7.0
1 1/4 303105D 50 29.0 5.7
1 1/2 303106D 50 28.0 4.7
1 3/4 303107D 50 25.0 3.7
2 303108D 50 29.0 3.6
2 1/2 303110D 50 30.0 3.0
3 303112D 50 29.0 2.4
12 303148D 10 29.0 0.6
1/2 x 9/32 x 1 303204D 50 42.0 10.6
1 1/4 303205D 50 43.0 8.5
1 1/2 303206D 50 44.0 7.3
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Load @ 40% of free length
Spring Rate per 1/10 inch Def.
1/2 x 9/32 x 1 3/4 303207D 50 44.0 6.4
2 303208D 50 43.0 5.3
2 1/2 303210D 50 41.0 4.1
3 303212D 10 40.0 3.4
3 1/2 303214D 10 38.0 2.7
4 303216D 10 38.0 2.3
12 303248D 10 37.0 0.8
5/8 x 11/32 x 1 303304D 50 71.0 18.1
1 1/4 303305D 50 67.0 13.3
1 1/2 303306D 50 70.0 11.7
1 3/4 303307D 50 71.0 10.2
2 303308D 50 71.0 8.9
2 1/2 303310D 50 73.0 7.2
3 303312D 10 68.0 5.7
3 1/2 303314D 10 72.0 5.1
4 303316D 10 70.0 4.3
4 1/2 303318D 10 68.0 3.8
12 303348D 10 70.0 1.5
3/4 x 3/8 x 1 303404D 50 125.0 31.6
1 1/4 303405D 50 125.0 24.8
1 1/2 303406D 50 117.0 19.6
1 3/4 303407D 50 110.0 15.8
2 303408D 50 114.0 14.2
2 1/2 303410D 50 108.0 10.7
3 303412D 10 110.0 9.2
3 1/2 303414D 10 105.0 7.5
4 303416D 10 109.0 6.8
4 1/2 303418D 10 112.0 6.3
5 303420D 10 107.0 5.4
5 1/2 303422D 10 108.0 4.9
6 303424D 10 103.0 4.3
12 303448D 10 105.0 2.2
1 x 1/2 x 1 303504D 50 232 58.9
1 1/4 303505D 50 232 46.1
1 1/2 303506D 50 221 36.9
1 3/4 303507D 50 213 30.7
2 303508D 50 210 26.2
2 1/2 303510D 50 205 20.4
3 303512D 10 195 16.3
3 1/2 303514D 10 198 14.1
4 303516D 10 189 11.8
4 1/2 303518D 10 190 10.6
5 303520D 10 190 9.5
5 1/2 303522D 10 183 8.3
6 303524D 10 186 7.8
7 303528D 10 189 6.7
8 303532D 10 193 6.0
12 303548D 10 185 3.9
1 1/4 x 5/8 x 1 1/2 303606D 10 314 52.4
1 3/4 303607D 10 329 47.5
2 303608D 10 324 40.3
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Load @ 40% of free length
Spring Rate per 1/10 inch Def.
1 1/4 x 5/8 x 2 1/2 303610D 10 317 31.4
3 303612D 10 312 26.1
3 1/2 303614D 10 309 22.0
4 303616D 10 309 19.3
4 1/2 303618D 10 307 17.1
5 303620D 10 295 14.7
5 1/2 303622D 10 299 13.6
6 303624D 10 297 12.4
7 303628D 10 282 10.1
8 303632D 5 285 8.9
10 303640D 5 288 7.2
12 303648D 5 263 5.5
1 1/2 x 3/4 x 2 303708D 10 480 59.7
2 1/2 303710D 10 458 45.4
3 303712D 10 455 38.0
3 1/2 303714D 10 458 32.7
4 303716D 10 446 27.7
4 1/2 303718D 10 443 24.7
5 303720D 10 448 22.4
5 1/2 303722D 10 440 20.0
6 303724D 10 434 18.1
7 303728D 10 437 15.6
8 303732D 5 428 13.4
10 303740D 5 431 10.8
12 303748D 5 424 8.8
2 x 1 x 2 1/2 303810D 10 855 84.8
3 303812D 10 855 71.5
3 1/2 303814D 10 836 59.7
4 303816D 10 829 51.6
4 1/2 303818D 10 806 44.9
5 303820D 10 804 40.2
5 1/2 303822D 5 794 36.0
6 303824D 5 778 32.5
7 303828D 5 778 27.8
8 303832D 5 763 23.9
10 303840D 5 814 20.4
12 303848D 5 734 15.3
2 1/2 x 1 1/2 x 3 303912D 5 1307 109.2
3 1/2 303914D 5 1260 89.9
4 303916D 5 1248 77.7
4 1/2 303918D 5 1211 67.4
5 303920D 5 1207 60.3
6 303924D 5 1180 49.3
7 303928D 5 1179 42.1
8 303932D 5 1154 36.1
10 303940D 5 1139 28.5
12 303948D 5 1124 23.4
LOAD DEFLECTION
For Long Life (30% of free length)
Maximum Operation Def (40% of free length)
For Optimum Life(25% of free length)
FREE LENGTH
HOLE
ROD
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 9
®
SPRINGS ISO D-LINE BLUE MEDIUM DUTY
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Load @ 40% of free length
Spring Rate per 1/10 inch Def.
1 1/4 x 5/8 x 2 1/2 303610D 10 317 31.4
3 303612D 10 312 26.1
3 1/2 303614D 10 309 22.0
4 303616D 10 309 19.3
4 1/2 303618D 10 307 17.1
5 303620D 10 295 14.7
5 1/2 303622D 10 299 13.6
6 303624D 10 297 12.4
7 303628D 10 282 10.1
8 303632D 5 285 8.9
10 303640D 5 288 7.2
12 303648D 5 263 5.5
1 1/2 x 3/4 x 2 303708D 10 480 59.7
2 1/2 303710D 10 458 45.4
3 303712D 10 455 38.0
3 1/2 303714D 10 458 32.7
4 303716D 10 446 27.7
4 1/2 303718D 10 443 24.7
5 303720D 10 448 22.4
5 1/2 303722D 10 440 20.0
6 303724D 10 434 18.1
7 303728D 10 437 15.6
8 303732D 5 428 13.4
10 303740D 5 431 10.8
12 303748D 5 424 8.8
2 x 1 x 2 1/2 303810D 10 855 84.8
3 303812D 10 855 71.5
3 1/2 303814D 10 836 59.7
4 303816D 10 829 51.6
4 1/2 303818D 10 806 44.9
5 303820D 10 804 40.2
5 1/2 303822D 5 794 36.0
6 303824D 5 778 32.5
7 303828D 5 778 27.8
8 303832D 5 763 23.9
10 303840D 5 814 20.4
12 303848D 5 734 15.3
2 1/2 x 1 1/2 x 3 303912D 5 1307 109.2
3 1/2 303914D 5 1260 89.9
4 303916D 5 1248 77.7
4 1/2 303918D 5 1211 67.4
5 303920D 5 1207 60.3
6 303924D 5 1180 49.3
7 303928D 5 1179 42.1
8 303932D 5 1154 36.1
10 303940D 5 1139 28.5
12 303948D 5 1124 23.4
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 40% of free length
Load at 1/10 in Def. (lb.)
3/8 x 3/16 x 1 304104D 50 35.0 8.9
1 1/4 304105D 50 39.0 7.7
1 1/2 304106D 50 40.0 6.7
1 3/4 304107D 50 38.0 5.5
2 304108D 50 40.0 4.9
2 1/2 304110D 50 38.0 3.8
3 304112D 50 38.0 3.1
12 304148D 10 37.0 0.8
1/2 x 9/32 x 1 304204D 50 66.0 16.8
1 1/4 304205D 50 65.0 12.8
1 1/2 304206D 50 64.0 10.7
1 3/4 304207D 50 63.0 9.1
2 304208D 50 63.0 7.8
2 1/2 304210D 50 60.0 6.0
3 304212D 10 59.0 5.0
3 1/2 304214D 10 60.0 4.3
4 304216D 10 58.0 3.6
12 304248D 10 59.0 1.2
5/8 x 11/32 x 1 304304D 50 125.0 31.8
1 1/4 304305D 50 115.0 22.8
1 1/2 304306D 50 118.0 19.8
1 3/4 304307D 50 121.0 17.5
2 304308D 50 122.0 15.2
2 1/2 304310D 50 120.0 11.9
3 304312D 10 122.0 10.2
3 1/2 304314D 10 120.0 8.6
4 304316D 10 122.0 7.6
4 1/2 304318D 10 121.0 6.7
12 304348D 10 115.0 2.4
3/4 x 3/8 x 1 304404D 50 205.0 52.0
1 1/4 304405D 50 195.0 38.8
1 1/2 304406D 50 188.0 31.5
1 3/4 304407D 50 185.0 26.6
2 304408D 50 183.0 22.8
2 1/2 304410D 50 177.0 17.6
3 304412D 10 176.0 14.7
3 1/2 304414D 10 177.0 12.6
4 304416D 10 178.0 11.1
4 1/2 304418D 10 176.0 9.7
5 304420D 10 175.0 8.7
5 1/2 304422D 10 176.0 8.1
6 304424D 10 175.0 7.3
12 304448D 10 176.0 3.7
1 x 1/2 x 1 304504D 50 385.0 97.9
1 1/4 304505D 50 364.0 72.2
1 1/2 304506D 50 356.0 59.5
1 3/4 304507D 50 352.0 50.9
2 304508D 50 342.0 42.6
2 1/2 304510D 50 329.0 32.7
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 40% of free length
Load at 1/10 in Def. (lb.)
1 x 1/2 x 3 304512D 10 335.0 28.0
3 1/2 304514D 10 327.0 23.3
4 304516D 10 328.0 20.4
4 1/2 304518D 10 327.0 18.1
5 304520D 10 325.0 16.3
5 1/2 304522D 10 329.0 15.0
6 304524D 10 325.0 13.6
7 304528D 10 322.0 11.5
8 304532D 10 322.0 10.1
12 304548D 10 317.0 6.6
1 1/4 x 5/8 x 1 1/2 304606D 10 570.0 95.3
1 3/4 304607D 10 540.0 77.9
2 304608D 10 533.0 66.4
2 1/2 304610D 10 504.0 50.0
3 304612D 10 485.0 40.5
3 1/2 304614D 10 483.0 34.5
4 304616D 10 473.0 29.4
4 1/2 304618D 10 473.0 26.1
5 304620D 10 476.0 23.8
5 1/2 304622D 10 473.0 21.6
6 304624D 10 461.0 19.3
7 304628D 10 463.0 16.5
8 304632D 5 454.0 14.2
10 304640D 5 456.0 11.4
12 304648D 5 458.0 9.5
1 1/2 x 3/4 x 2 304708D 10 781.0 97.3
2 1/2 304710D 10 741.0 73.5
3 304712D 10 733.0 61.2
3 1/2 304714D 10 713.0 50.9
4 304716D 10 693.0 43.1
4 1/2 304718D 10 691.0 38.2
5 304720D 10 696.0 34.8
5 1/2 304722D 10 692.0 31.6
6 304724D 10 694.0 29.0
7 304728D 10 688.0 24.6
8 304732D 5 682.0 21.3
10 304740D 5 687.0 17.2
12 304748D 5 679.0 14.1
2 1/2 x 1 x 2 1/2 304810D 10 1219.0 121.0
3 304812D 10 1136.0 94.9
3 1/2 304814D 10 1116.0 79.6
4 304816D 10 1113.0 69.3
4 1/2 304818D 10 1106.0 61.1
5 304820D 10 1082.0 54.1
5 1/2 304822D 5 1080.0 49.4
6 304-824-D 5 1070.0 44.7
7 304828D 5 1054.0 37.6
8 304832D 5 1043.0 32.6
9 304836D 5 1047.0 29.0
10 304840D 5 1050.0 26.2
12 304848D 5 1040.0 21.6
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 40% of free length
Load at 1/10 in Def. (lb.)
2 1/2 x 1 1/2 x 3 304912D 5 2074.0 173.3
3 1/2 304914D 5 1980.0 141.3
4 304916D 5 1933.0 120.4
4 1/2 304918D 5 1899.0 104.8
5 304920D 5 1857.0 92.8
6 304924D 5 1809.0 75.6
7 304928D 5 1778.0 63.4
8 304932D 5 1768.0 55.3
9 304936D 5 1769.0 49.0
10 304940D 5 1769.0 44.2
12 304948D 5 1759.0 36.6
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
For Long Life (30% of free length)
Maximum Operation Def. (40% of free length)
For Optimum Life(25% of free length)
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196410
®
SPRINGS ISO D-LINE RED HEAVY DUTY
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 30% of free length
Load at 1/10 in Def. (lb.)
3/8 x 3/16 x 1 305104D 50 39.0 13.3
1 1/4 305105D 50 39.0 10.2
1 1/2 305106D 50 43.0 9.5
1 3/4 305107D 50 43.0 8.3
2 305108D 50 41.0 6.8
2 1/2 305110D 50 43.0 5.6
3 305112D 50 40.0 4.5
12 305148D 10 40.0 1.1
1/2 x 9/32 x 1 305204D 50 71.0 24.2
1 1/4 305205D 50 69.0 18.2
1 1/2 305206D 50 69.0 15.4
1 3/4 305207D 50 71.0 13.6
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 30% of free length
Load at 1/10 in Def. (lb.)
1/2 x 9/32 x 2 305208D 50 69.0 11.4
2 1/2 305210D 50 66.0 8.7
3 305212D 10 69.0 7.7
3 1/2 305214D 10 66.0 6.3
4 1/2 305216D 10 65.0 4.8
12 305248D 10 65.0 1.8
5/8 x 11/32 x 1 305304D 50 131.0 44.5
1 1/4 305305D 50 132.0 34.8
1 1/2 305306D 50 130.0 29.0
1 3/4 305307D 50 135.0 26.0
2 305308D 50 127.0 21.1
2 1/2 305310D 50 127.0 16.8
3 305312D 50 132.0 14.7
3 1/2 305314D 10 131.0 12.5
4 305316D 10 130.0 10.8
4 1/2 305318D 10 121.0 9.0
12 305348D 10 127.0 3.5
3/4 x 3/8 x 1 305404D 50 370.0 125.1
1 1/4 305405D 50 370.0 97.8
1 1/2 305406D 50 350.0 78.0
1 3/4 305407D 50 345.0 66.4
2 305408D 50 332.0 55.2
2 1/2 305410D 50 320.0 42.4
3 305412D 10 322.0 35.9
3 1/2 305414D 10 323.0 30.7
4 305416D 10 320.0 26.6
4 1/2 305418D 10 325.0 23.9
5 305420D 10 320.0 21.3
5 1/2 305422D 10 318.0 19.3
6 305424D 10 317.0 17.6
12 305448D 10 313.0 8.7
1 x 1/2 x 1 305504D 50 626 212.1
1 1/4 305505D 50 606 160.3
1 1/2 305506D 50 562.0 125.3
1 3/4 305507D 50 597.0 114.9
2 305508D 50 561.0 93.1
2 1/2 305510D 50 548.0 72.6
3 305512D 50 550.0 61.3
3 1/2 305514D 10 541.0 51.4
4 305516D 10 539.0 44.7
4 1/2 305518D 10 548.0 40.3
5 305520D 10 541.0 36.1
5 1/2 305522D 10 539.0 32.8
6 305524D 10 544.0 30.3
7 305528D 10 543.0 25.8
8 305532D 10 540.0 22.5
12 305548D 10 550.0 15.3
1 1/4 x 5/8 x 1 1/2 305606D 10 992.0 221.1
1 3/4 305607D 10 929.0 178.7
2 305608D 10 920.0 152.7
2 1/2 305610D 10 882.0 116.7
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 30% of free length
Load at 1/10 in Def. (lb.)
1 1/4 x 5/8 x 3 305612D 10 880.0 98.0
3 1/2 305614D 10 849.0 80.8
4 305616D 10 850.0 70.6
4 1/2 305618D 10 851.0 62.7
5 305620D 10 846.0 56.4
5 1/2 305622D 10 836.0 50.9
6 305624D 10 838.0 46.7
7 305628D 5 831.0 39.5
8 305632D 5 831.0 34.6
10 305640D 5 829.0 27.6
12 305648D 5 827.0 22.9
1 1/2 x 3/4 x
2 305708D 10 1278.0 212.2
2 1/2 305710D 10 1295.0 171.3
3 305712D 10 1197.0 133.4
3 1/2 305714D 10 1183.0 112.5
4 305716D 10 1172.0 97.3
4 1/2 305718D 10 1208.0 88.9
5 305720D 10 1177.0 78.5
5 1/2 305722D 10 1157.0 70.5
6 305724D 10 1172.0 65.3
7 305728D 10 1162.0 55.2
8 305732D 5 1160.0 48.4
10 305740D 5 1158.0 38.6
12 305748D 5 1156.0 32.1
2 x 1 x 2 1/2 305810D 10 1831.0 242.3
3 305812D 10 1718.0 191.3
3 1/2 305814D 10 1662.0 158.1
4 305816D 10 1685.0 139.8
4 1/2 305818D 10 1665.0 122.5
5 305820D 10 1620.0 108.0
5 1/2 305822D 5 1585.0 96.5
6 305824D 5 1579.0 88.8
7 305828D 5 1571.0 74.7
8 305832D 5 1575.0 65.7
10 305840D 5 1551.0 51.7
12 305848D 5 1553.0 43.1
2 1/2 x 1 1/2 x 3 305912D 5 -- 352.9
3 1/2 305914D 5 -- 294.1
4 305916D 5 -- 250.1
4 1/2 305918D 5 -- 211.3
5 305920D 5 -- 190.1
6 305924D 5 -- 153.6
7 305928D 5 -- 129.0
8 305932D 5 -- 113.1
9 305936D 5 -- 82.0
10 305940D 5 -- 88.5
12 305948D 5 -- 73.1
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
For Long Life (25% of free length)
Maximum Operation Def. (30% of free length)
For Optimum Life(20% of free length)
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 11
®
SPRINGSISO D-LINE YELLOW EXTRA HEAVY DUTY
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 25% of free length
Load at 1/10 in Def. (lb.)
3/8 x 3/16 x 1 306104D 50 51.0 20.8
1 1/4 306105D 50 49.0 15.7
1 1/2 306106D 50 50.0 13.3
1 3/4 306107D 50 49.0 11.2
2 306108D 50 48.0 9.6
2 1/2 306110D 50 48.0 7.6
3 306112D 50 48.0 6.4
12 306148D 10 47.0 1.6
1/2 x 9/32 x 1 306204D 50 77.0 31.2
1 1/4 306205D 50 76.0 24.2
1 1/2 306206D 50 74.0 19.7
1 3/4 306207D 50 69.0 15.9
2 306208D 50 72.0 14.4
2 1/2 306210D 50 72.0 11.4
3 306212D 10 71.0 9.5
3 1/2 306214D 10 70.0 8.0
4 306216D 10 73.0 7.3
12 306248D 10 66.0 2.2
5/8 x 11/32 x
1 306304D 50 191.0 77.8
1 1/4 306305D 50 178.0 56.6
1 1/2 306306D 50 177.0 47.3
1 3/4 306307D 50 175.0 40.4
2 306308D 50 174.0 34.6
2 1/2 306310D 50 173.0 27.4
3 306312D 10 170.0 22.8
3 1/2 306314D 10 171.0 19.5
4 306316D 10 169.0 16.8
4 1/2 306318D 10 170.0 15.1
12 306348D 10 168.0 5.6
3/4 x 3/8 x 1 306404D 50 445.0 186.4
1 1/4 306405D 50 427.0 139.8
1 1/2 306406D 50 412.0 113.7
1 3/4 306407D 50 398.0 97.2
2 306408D 50 397.0 83.9
2 1/2 306410D 50 389.0 65.5
3 306412D 10 379.0 53.7
3 1/2 306414D 10 370.0 44.8
4 306416D 10 369.0 38.9
4 1/2 306418D 10 368.0 34.4
5 306420D 10 364.0 30.9
5 1/2 306422D 10 357.0 27.7
6 306424D 10 358.0 25.4
12 306448D 10 355.0 12.6
1 x 1/2 x 1 306504D 50 655.0 262.1
1 1/4 306505D 50 626.0 198.8
1 1/2 306506D 50 592.0 158.3
1 3/4 306507D 50 584.0 134.9
2 306508D 50 564.0 112.4
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 25% of free length
Load at 1/10 in Def. (lb.)
1 x 1/2 x 2 1/2 306510D 50 558.0 88.6
3 306512D 10 552.0 73.9
3 1/2 306514D 10 543.0 62.0
4 306516D 10 546.0 54.4
4 1/2 306518D 10 549.0 48.5
5 306520D 10 545.0 43.6
5 1/2 306522D 10 541.0 39.6
6 306524D 10 542.0 36.2
7 306528D 10 546.0 31.1
8 306532D 10 544.0 27.2
12 306548D 10 540.0 18.0
1 1/4 x 5/8 x 1 1/2 306606D 10 1022.0 273.1
1 3/4 306607D 10 1039.0 239.8
2 306608D 10 1007.0 200.7
2 1/2 306610D 10 983.0 156.1
3 306612D 10 968.0 129.4
3 1/2 306614D 10 968.0 110.5
4 306616D 10 931.0 92.8
4 1/2 306618D 10 935.0 82.6
5 306620D 10 946.0 75.6
5 1/2 306622D 10 928.0 67.8
6 306624D 10 931.0 62.2
7 306628D 10 919.0 52.4
8 306632D 5 918.0 45.9
10 306640D 5 917.0 36.7
12 306648D 5 915.0 30.5
1 1/2 x 3/4 x 2 306708D 10 1687.0 336.1
2 1/2 306710D 10 1629.0 258.6
3 306712D 10 1597.0 213.4
3 1/2 306714D 10 1570.0 179.3
4 306716D 10 1570.0 156.3
4 1/2 306718D 10 1569.0 138.6
5 306720D 10 1556.0 124.5
5 1/2 306722D 10 1533.0 112.0
6 306724D 10 1536.0 102.6
7 306732D 10 1520.0 86.7
8 306740D 5 1514.0 75.7
10 306742D 5 1507.0 60.3
12 306748D 5 1506.0 50.2
2 1/2 x 1 x
2 1/2 306810D 10 2415.0 383.4
3 306812D 10 2294.0 306.7
3 1/2 306814D 10 2257.0 257.6
4 306816D 10 2230.0 222.1
4 1/2 306818D 10 2209.0 195.2
5 306820D 10 2176.0 174.1
5 1/2 306822D 5 2149.0 157.1
6 306824D 5 2141.0 143.1
7 306832D 5 2090.0 119.3
8 306840D 5 2110.0 105.6
10 306842D 5 2091.0 83.6
12 306848D 5 2057.0 68.5
Load Deflection Table
HOLE (O.D.) x ROD (I.D.)
Length PRODUCTO Part#
Bag Qty
Max. Oper Def 25% of free length
Load at 1/10 in Def. (lb.)
2 1/2 x 1 1/2 x 3 306912D 5 -- 544.0
3 1/2 306914D 5 -- 468.0
4 306916D 5 -- 400.0
4 1/2 306918D 5 -- 354.0
5 306920D 5 -- 323.0
6 306924D 5 -- 262.0
7 306928D 5 -- 219.0
8 306932D 5 -- 192.0
10 306940D 5 -- 150.0
12 306948D 5 -- 124.0
FREE LENGTH
HOLE
ROD
LOAD DEFLECTION
For Long Life (20% of free length)
Maximum Operation Def. (25% of free length)
For Optimum Life(17% of free length)
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196412
®
COMPRESSION SPRINGSNUMERICAL LISTING BY OUTSIDE DIAMETER
* Conical Spring ** Barrel Spring + Square Wire
Part # Outside Diameter (in)
Free Length (in)
Wire Diameter (in)
Rate(lbs. / in)
SolidHeight
UnitPack
020-074 0.078 0.53 0.012 5.67 0.264 12
020-073 0.078 0.56 0.011 3.90 0.231 12
020-076 0.109 0.81 0.018 12.00 0.342 12
020-075 0.109 0.91 0.018 9.30 0.414 12
020-125 0.120 0.62 0.016 6.61 0.252 25
020-126 0.120 0.75 0.016 5.32 0.304 25
020-077 0.172 0.22 0.012 1.15 0.120 12
020-056 0.176 10.00 0.014 0.15 2.254 12
020-127 0.180 0.75 0.022 8.70 0.281 25
020-128 0.180 1.12 0.022 6.80 0.352 25
020-129 0.180 1.12 0.022 7.00 0.330 25
020-130 0.180 1.25 0.022 6.50 0.424 25
020-084 0.188 0.94 0.012 0.32 0.240 12
020-131 0.240 1.00 0.026 7.80 0.306 25
020-132 0.240 1.25 0.026 5.50 0.403 25
020-133 0.240 1.50 0.026 4.60 0.445 25
020-055 0.250 10.00 0.022 0.26 2.486 12
020-080 0.281 1.25 0.040 18.00 0.640 12
020-079 0.281 1.31 0.040 21.05 0.540 12
020-098 0.281 2.06 0.020 0.29 0.510 12
020-085 0.312 0.88 0.025 Ph. Brz 2.60 0.200 12
020-081 0.312 1.97 0.022 0.65 0.528 12
020-082 0.312 2.44 0.032 1.30 0.768 12
020-083 0.312 2.44 0.028 1.00 0.672 12
020-054 0.312 10.00 0.022 0.19 2.266 12
020-053 0.359 12.00 0.048 2.20 5.273 12
020-134 0.360 1.50 0.035 6.87 0.416 25
020-135 0.360 1.75 0.035 6.30 0.446 25
020-136 0.360 2.00 0.035 5.40 0.560 25
020-086 0.375 0.78 0.042 Brass 7.40 0.378 12
020-088 0.375 2.03 0.048 11.00 0.998 12
020-094 0.375 2.21 0.063 42.00 1.147 12
020-052 0.375 11.50 0.047 2.71 4.240 12
020-093 0.438 2.00 0.054 15.40 0.972 12
020-071 0.438 2.56 0.041 2.60 1.117 12
020-089 0.438 2.63 0.048 7.20 0.950 12
020-090 0.469 2.50 0.053 12.00 0.918 12
020-060 0.500 0.97 0.072 Ph. Brz 52.00 0.612 12
020-092 0.500 2.06 0.048 5.60 0.808 12
020-091 0.500 2.50 0.063 18.00 1.000 12
Part # Outside Diameter (in)
Free Length (in)
Wire Diameter (in)
Rate(lbs. / in)
SolidHeight
UnitPack
020-051 0.516 12.00 0.063 2.80 5.438 12
020-059 0.531 1.03 0.105 436.00 0.950 12
020-109 0.562 4.38 0.102 42.15 2.344 12
020-069 0.590 2.19 0.040 3.55 0.380 12
020-123 0.600 1.50 0.070 40.00 0.560 12
020-068 0.625 2.84 0.080 30.00 1.080 12
020-050 0.625 11.50 0.054 1.22 3.564 6
020-121 0.688 1.06 0.149 1230.00 0.814 12
020-067 0.688 4.06 0.105 53.70 1.952 12
020-115 0.719 0.88 0.125 550.00 0.625 12
020-049 0.734 12.00 0.080 3.80 4.880 3
020-114 0.750 1.75 0.125 220.00 1.063 12
020-072 0.750 2.63 0.106 72.00 1.166 12
020-070 0.844 1.10 0.080 Brass 21.50 0.360 12
020-066 0.859 2.59 0.135 154.00 1.485 12
020-065 0.875 2.00 0.120 110.00 0.964 12
020-064 0.875 3.06 0.092 21.50 1.098 12
020-048 0.875 10.00 0.080 3.20 3.000 3
020-047 0.875 12.00 0.105 8.00 5.170 3
020-124 0.906 0.75 0.141 x 0.187 1632.00 0.494 12
020-119 0.938 1.00 0.207 2800.00 0.880 6
020-063 0.938 2.03 0.080 16.00 0.640 12
020-122 0.995 2.50 0.145 130.00 1.400 12
020-062 1.015 2.56 0.120 56.00 1.148 12
020-118 1.175 1.06 0.225 2400.00 0.845 12
020-120 1.312 1.25 0.125 92.12 0.687 12
020-117+ 1.468 1.25 0.281 3960.00 1.124 12
020-078* 0.281 x 1.560 0.50 0.013 0.68 0.117 12
020-087* 0.531 x 0.281 0.91 0.072 56.00 0.522 12
020-061** 0.531 x 1.031 x 0.859
3.50 0.051 1.83 0.714 12
020-058* 0.625 x 0.750 1.00 0.080 Brass 33.45 0.440 12
020-057* 0.656 x 0.938 0.94 0.058 Ph. Brz 5.08 0.363 12
COMPRESSION SPRINGS
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 13
®
EXTENSION SPRINGSNUMERICAL LISTING BY FREE LENGTH
Part # Free Length(in)
Outside Diameter (in)
Wire Diameter (in)
Rate (lbs./in)
Approx. Load @ Ref. Ext. (in)
Unit Pack
020-137 0.620 0.120 0.016 3.30 1.6 lbs @ 1.07” 25
020-138 0.750 0.120 0.016 2.50 1.6 lbs @ 1.34” 25
020-139 0.880 0.120 0.016 2.00 1.6 lbs @ 1.62” 25
020-042 1.000 0.188 0.014 0.19 .14 lbs @ 1.5” 12
020-140 1.000 0.180 0.022 2.80 2.6 lbs @ 1.86” 25
020-141 1.120 0.180 0.022 2.40 2.6 lbs @ 2.13” 25
020-040 1.125 0.234 0.020 0.75 .53 lbs @ 1.625” 12
020-039 1.130 0.300 0.040 Brass 5.25 2.0 lbs @ 1.200” 12
020-142 1.250 0.180 0.022 2.00 2.6 lbs @ 2.43” 25
020-143 1.370 0.240 0.026 1.80 3.3 lbs @ 2.96” 25
020-037 1.438 0.344 0.048 15.00 10.0 lbs @ 1.812” 12
020-144 1.500 0.240 0.026 1.60 3.3 lbs @ 2.96 25
020-146 1.500 0.360 0.037 3.40 5.9 lbs @ 3.06” 25
020-034 1.625 0.500 0.080 74.93 23.0 lbs @ 1.875” 12
020-145 1.750 0.240 0.026 1.30 3.3 lbs @ 1.75” 25
020-147 1.750 0.360 0.037 2.89 5.9 lbs @ 3.77 25
020-148 2.000 0.360 0.037 2.20 5.9 lbs @ 4.44” 25
020-095 2.000 0.718 0.107 90.86 51.0 lbs @ 2.5” 12
020-035 2.062 0.156 0.020 Brass 0.50 8.5 lbs @ 2.812” 12
020-032 2.594 0.750 0.105 46.00 29.5 lbs @ 2.968 12
020-033 2.656 0.750 0.080 10.30 12.5 lbs @ 3.656” 12
020-097 3.000 0.719 0.105 41.03 33.0 lbs @ 3.25” 12
020-019 3.250 0.375 0.041 1.90 5.2 lbs @ 5.25” 12
020-099 3.875 0.688 0.105 32.83 40.0 lbs @ 5.0” 6
020-020 4.000 0.250 0.028 0.81 1.9 lbs @ 6.0” 12
020-113 4.000 0.625 0.113 70.00 93.0 lbs @ 5.0” 12
020-024 4.000 0.719 0.105 30.78 36.5 lbs @ 5.0” 12
020-023 4.062 0.734 0.063 1.73 4.3 lbs @ 6.062” 12
020-022 4.500 0.484 0.063 4.86 14.0 lbs @ 6.5” 12
020-026 5.000 0.312 0.041 1.81 3.1 lbs @ 6.5” 12
020-028 5.250 0.438 0.063 6.50 16.0 lbs @ 7.25” 12
020-025 5.250 0.531 0.062 5.00 8.5 lbs @ 6.25” 12
020-018 5.344 0.250 0.041 4.30 8.0 lbs @ 5.843” 12
020-027 5.375 0.344 0.048 2.60 6.2 lbs @ 7.375” 12
020-014 5.500 0.375 0.054 4.00 10.0 lbs @ 7.5” 12
020-013 5.500 0.562 0.080 10.50 24.5 lbs @ 7.0” 12
020-012 5.625 0.547 0.080 10.00 24.0 lbs @ 7.625” 12
020-017 5.750 0.250 0.028 0.59 1.6 lbs @ 7.75” 12
020-015 5.750 0.297 0.048 4.40 9.3 lbs @ 7.75” 12
020-112 6.000 0.734 0.062 0.93 2.70 lbs @ 6.976” 12
Part # Free Length(in)
Outside Diameter (in)
Wire Diameter (in)
Rate (lbs./in)
Approx. Load @ Ref. Ext. (in)
Unit Pack
020-029 6.000 0.875 0.120 18.50 26.5 lbs @ 7.0” 6
020-016 6.125 0.266 0.035 1.10 4.0 lbs @ 8.125” 12
020-111 6.250 0.750 0.080 3.30 8.0 lbs @ 8.25” 12
020-009 6.438 0.438 0.048 1.10 4.2 lbs @ 8.437” 12
020-010 6.500 0.328 0.035 0.58 2.2 lbs @ 8.5” 12
020-011 6.625 0.156 0.026 1.81 2.2 lbs @ 8.625” 12
020-116 6.750 0.906 0.092 3.00 6.0 lbs @ 7.75” 12
020-104 7.625 1.250 0.207 93.80 170.0 lbs @ 8.625” 2
020-030 8.000 1.062 0.135 13.48 38.0 lbs @ 10.0” 6
020-007 8.125 0.344 0.048 1.60 6.3 lbs @ 10.125” 12
020-105 8.188 1.812 0.250 65.00 98.0 lbs @ 9.188” 2
020-031 8.500 1.000 0.105 3.96 16.8 lbs @ 10.25” 3
020-008 9.062 0.172 0.029 1.00 3.5 lbs @ 10.125” 12
020-005 10.000 0.359 0.054 2.30 6.2 lbs @ 13.0” 12
020-006 10.000 0.375 0.047 1.32 5.5 lbs @ 13.0” 12
020-004 10.000 0.500 0.062 2.09 10.2 lbs @ 12.0” 12
020-003 10.000 0.625 0.072 2.10 8.8 lbs @ 13.0” 6
020-002 10.000 0.812 0.072 0.75 5.6 lbs @ 12.0” 3
020-001 10.000 0.875 0.092 2.50 11.5 lbs @ 13.0” 3
020-100 10.000 1.125 0.148 14.00 48.0 lbs @ 13.0” 6
020-101 12.000 1.250 0.162 12.60 66.0 lbs @ 15.0” 6
020-102 14.000 1.375 0.177 13.00 74.0 lbs @ 18.0” 6
020-158 15.125 0.984 0.080 0.47 2.99 lbs @ 15.94” 12
020-152 16.000 0.297 0.041 0.70 4.3 lbs @ 17.86” 12
020-153 16.000 0.344 0.048 0.98 4.3 lbs @ 17.59” 12
020-154 16.000 0.375 0.054 1.34 5.9 lbs @ 17.94” 12
020-155 16.000 0.422 0.063 2.20 9.0 lbs @ 17.73” 12
020-156 16.000 0.438 0.072 4.06 11.7 lbs @ 17.88” 12
020-108 16.000 1.125 0.105 3.00 5.5 lbs @ 18.0” 12
020-103 16.000 1.562 0.207 16.50 100.0 lbs @ 21.0” 6
EXTENSION SPRINGS
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196414
®
EASY SPRING SELECTORCOMPRESSION
WIRE STOCK# OD FL RATE ENDS SOLID HT
0.010 3-32-10 .0930 * 10.00 0.12 P 2.800
0.011 020-073 0.078 0.56 3.90 S&G 0.231
115 0.156 2.00 0.23 SQ 0.352
0.012 020-077 0.172 0.21 1.15 S&G 0.120
020-074 0.078 0.53 5.67 S&G 0.264
020-084 0.188 0.94 0.32 SQ 0.240
1-8-12 .1250 * 10.00 0.11 P 3.000
0.013 020-078 .2810X 0.50 0.68 SQ 0.117
(CONICAL) 1.56
0.014 3-32-14 .0930 * 10.00 0.50 P 3.990
3-16-14 .1880 * 10.00 0.08 P 1.960
020-056 0.176 10.00 0.15 P 2.254
0.015 20 0.2188 1.62 0.45 SQ 0.330
120 0.2188 1.62 0.45 SQ 0.330
419 0.2188 1.62 0.45 SQ 0.330
0.016 020-125 0.1200 0.62 6.61 SQ 2.520
020-126 0.1200 0.75 5.32 SQ 3.040
1-8-16 .1250 * 10.00 0.38 P 4.000
0.017 C-6 .2500 * 0.75 1.60 SQ
C-7 .2500 * 1.50 0.66 SQ
161 0.2500 2.00 SQ
0.018 020-076 0.1090 0.81 12.00 SQ 0.342
020-075 0.1090 0.90 9.30 P 0.414
3-16-18 .1880 * 10.00 0.26 P 2.520
1-4-18 .2500 * 10.00 0.14 P 1.710
0.020 126 0.1875 0.87 3.08 SQ 0.380
421 0.1875 1.25 4.11 SQ 0.300
71X 0.1875 1.50 2.24 SQ 0.500
18 0.3125 1.50 0.93 SQ 0.280
417 0.3125 1.50 0.93 SQ 0.280
501 0.1875 2.00 SQ
69X 0.2500 2.00 0.82 SQ 0.520
429 0.2500 2.00 0.82 SQ 0.520
503 0.2500 2.00 SQ
020-098 0.2810 2.06 0.29 SQ 0.510
0.021 159 ** 0.2500 2.50 SQ
0.022 020-127 0.1800 0.75 8.70 SQ 0.281
020-128 0.1800 1.00 6.80 SQ 0.352
21 0.1875 1.00 2.44 SQ 0.418
020-129 0.1800 1.12 7.00 SQ 0.330
020-130 0.1800 1.25 6.50 SQ 0.424
72X 0.2500 1.88 1.81 SQ 0.508
020-081 0.3125 1.97 0.65 SQ 0.528
020-055 0.2500 10.00 0.26 P 2.486
1-4-22 .2500 * 10.00 P
020-054 0.3125 10.00 0.19 P 2.266
5-16-22 .3125 * 10.00 0.15 P 2.200
0.023 420 0.1875 1.31 2.44 SQ 0.418
25 0.2500 2.00 2.02 SQ 0.460
424 0.2500 2.00 2.02 SQ 0.460
WIRE STOCK# OD FL RATE ENDS SOLID HT
0.025 020-085 0.3125 0.87 2.60 SQ 0.200
430 0.3125 1.43 1.75 SQ 0.412
74X 0.3125 1.43 1.75 SQ 0.412
99X 0.3750 1.87 1.00 SQ 0.400
94X 0.2500 2.00 2.59 SQ 0.550
157 0.1875 2.25 SQ
125 0.2812 2.31 2.09 SQ 0.475
123 0.2500 2.62 1.82 SQ 0.750
0.026 020-131 0.2400 1.00 7.80 SQ 0.306
020-132 0.2400 1.25 5.50 SQ 0.403
020-133 0.2400 1.50 4.60 SQ 0.445
23 0.3125 1.87 2.00 SQ 0.442
422 0.3125 1.87 2.00 SQ 0.442
3-16-26 .1875 * 10.00 1.39 P 3.380
1-4-26 .2500 * 10.00 0.69 P 2.470
C-129 .1250 * 11.00 P
C-128 .1875 * 11.00 P
0.027 112 0.2500 1.93 5.04 SQ 0.532
0.028 67X 0.3281 1.12 4.67 SQ 0.280
427 0.3281 1.12 4.67 SQ 0.280
165 ** 0.2812 2.30 SQ
020-083 0.3120 1.44 1.00 SQ 0.672
0.030 19 0.2031 2.25 8.37 SQ 1.248
418 0.2031 2.25 8.37 SQ 1.248
0.031 116 0.2500 1.31 14.54 SQ 0.416
1-4-31 .2500 * 10.00 1.46 P 3.100
5-16-31 .3125 * 10.00 0.63 P 3.410
3-8-31 .3750 * 10.00 0.33 P 3.410
0.032 22 0.2188 1.25 15.61 SQ 0.576
98X 0.2500 1.44 14.54 SQ 0.416
431 0.2500 1.44 14.54 SQ 0.416
92X 0.3125 1.69 5.72 SQ 0.480
87X 0.2344 1.75 12.19 SQ 0.676
507 0.3125 2.00 SQ
C-8 .3750 * 2.00 2.30 SQ
020-082 0.3125 2.44 1.30 SQ 0.768
C-9 .3750 * 3.00 1.20 SQ
C-127 .2188 * 11.00 P
C-126 .2500 * 11.00 P
C-125 .3125 * 11.00 P
C-124 .3750 * 11.00 P
377 0.3750 12.00 0.37 P 3.232
0.035 77X 0.3750 1.44 3.70 SQ 0.560
90X 0.3125 1.50 7.24 SQ 0.595
020-134 0.3600 1.50 6.87 SQ 0.416
020-135 0.3600 1.75 6.30 SQ 0.446
020-136 0.3600 2.00 5.40 SQ 0.560
505 0.2500 2.00 SQ
511 0.3750 3.00 SQ
3-16-35 .1875 * 10.00 3.84 P 6.650
WIRE STOCK# OD FL RATE ENDS SOLID HT
1-4-35 .2500 * 10.00 1.82 P 4.550
3-8-35 .3750 * 10.00 0.61 P 3.500
7-16-35 .4375 * 10.00 0.54 P 2.450
1-2-35 .5000 * 10.00 0.25 P 3.150
0.036 163 ** 0.2500 2.50 SQ
C-1 .2500 * 10.00 2.40 P
0.037 5-16-37 .3125 * 10.00 1.35 P 4.070
0.040 020-080 0.2810 1.25 18.00 SQ 0.640
020-079 0.2810 1.31 21.05 P 0.540
020-069 0.5900 2.19 3.55 S&G 0.380
0.041 7 OR 407 .4062 X 1.00 SQ
TAPER 0.6875
122 0.3750 1.16 12.11 SQ 0.492
17 0.3125 1.38 29.14 SQ 0.410
416 0.3125 1.38 29.14 SQ 0.410
84X 0.4375 1.44 5.45 SQ 0.615
79X 0.3750 1.94 10.90 SQ 0.533
76X 0.3125 2.00 14.57 SQ 0.897
509 0.3125 2.00 SQ
24 0.3125 2.31 13.60 SQ 0.738
423 0.3125 2.31 13.60 SQ 0.738
020-071 0.4380 2.56 2.60 SQ 1.117
65 0.6250 2.69 1.56 SQ 0.656
515 0.5000 3.00 SQ
519 0.6250 4.00 SQ
54 0.4688 5.25 2.17 SQ 1.107
1-4-41 .2500 * 10.00 5.83 P 3.690
5-16-41 .3125 * 10.00 2.88 P 3.280
1-2-41 .5000 * 18.00 0.61 P 3.320
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 15
®
EASY SPRING SELECTORCOMPRESSION
WIRE STOCK# OD FL RATE ENDS SOLID HT
0.042 020-086 0.3750 0.78 7.40 SQ 0.378
WA-100 .3750 * 1.00 20.00 S&G 0.440
124 0.2188 1.50 61.04 SQ 0.615
WA-101 .3750 * 1.50 14.00 S&G 0.630
WA-102 .3750 * 2.00 12.00 S&G 0.815
WA-103 .3750 * 2.50 8.00 S&G 1.030
WA-104 .3750 * 3.00 6.00 S&G 1.210
0.043 167 ** 0.3125 2.38 SQ
3-8-43 0.3750 10.00 2.19 P 3.010
0.047 37 0.4688 1.13 15.66 SQ 0.423
95X 0.3125 1.50 24.97 SQ 0.705
428 0.3125 1.50 24.97 SQ 0.705
96X 0.3750 1.50 15.29 SQ 0.752
412 0.4375 1.75 11.82 SQ 0.611
82X 0.5000 1.75 10.77 SQ 0.470
12 .4375 X 2.00 SQ
(TAPER) 0.6875
513 0.3750 3.00 SQ
26 0.4375 3.00 8.44 SQ 0.799
425 0.4375 3.00 8.44 SQ 0.799
33 0.3281 3.31 13.17 SQ 1.269
45 0.7500 3.38 1.44 SQ 0.799
523 0.7500 4.00 SQ
1-4-47 .2500 * 10.00 9.35 P 4.700
5-16-47 .3125 * 10.00 6.06 P 3.530
3-8-47 .3750 * 10.00 2.67 P 4.000
7-16-47 .4375 * 10.00 1.87 P 3.290
1-2-47 .5000 * 10.00 1.10 P 3.530
020-052 0.3750 11.50 2.71 P 4.240
337 0.5000 12.00 1.50 P 2.397
299-B 0.5938 12.00 0.64 P 3.196
345 0.7500 12.00 0.39 P 2.491
0.048 020-088 0.3750 2.03 11.00 S&G 0.998
020-092 0.5000 2.06 5.60 SQ 0.808
C-10 .5000 * 2.50 4.00 SQ
020-089 0.4380 2.63 7.20 S&G 0.950
C-11 .5000 * 3.50 2.80 SQ
C-2 .2500 * 10.00 3.10 P
020-053 0.3590 12.00 2.20 P 5.273
0.051 020-061 .531 X 3.50 1.83 SQ 0.714
(BARREL) 1.031X 0.86
0.053 020-090 0.4690 2.50 12.00 S&G 0.918
0.054 85X 0.6250 1.56 6.66 SQ 0.702
13 0.5000 1.75 13.77 SQ 0.702
020-093 0.4380 2.00 15.40 SQ 0.972
411 .3125 X 2.00 SQ
(TAPER) 0.5625
020-050 0.6250 11.50 1.22 P 3.564
WIRE STOCK# OD FL RATE ENDS SOLID HT
1-2-54 .5000 * 18.00 2.32 P 3.890
5-8-54 .6250 * 18.00 1.42 P 2.920
0.055 5-16-55 .3125 * 10.00 11.45 P 4.400
3-8-55 .3750 * 10.00 7.03 P 3.300
7-16-55 .4375 * 10.00 4.49 P 3.300
1-2-55 .5000 * 10.00 2.33 P 3.850
0.058 020-057 .6560 X 0.94 5.08 SQ 0.363
(conical) 0.9380
0.062 WA-105 .5000 * 1.00 58.00 S&G 0.490
80x 0.5000 1.43 42.13 SQ 0.558
WA-106 .5000 * 1.50 42.00 S&G 0.690
WA-107 .5000 * 2.00 32.00 S&G 0.915
89X 0.6250 2.00 14.47 SQ 0.682
WA-108 .5000 * 2.50 25.00 S&G 1.050
41 0.5000 2.81 13.30 SQ 1.364
517 0.5000 3.00 SQ
WA-109 .5000 * 3.00 24.00 S&G 1.235
43 0.6875 3.00 7.25 SQ 0.930
32 0.4375 3.25 22.37 SQ 1.302
55 0.8125 3.25 3.35 SQ 1.116
WA-110 .5000 * 3.50 18.00 S&G 1.500
521 0.6250 4.00 SQ
527 1.0000 6.00 SQ
C-3 .5000 * 10.00 5.00 P
3-8-62 .3750 * 10.00 12.36 P 4.030
7-16-62 .4375 * 10.00 6.90 P 4.030
1-2-62 .5000 * 10.00 7.11 P 2.400
C-123 .4375 * 11.00 P
C-122 .5000 * 11.00 P
C-121 .5625 * 11.00 P
C-120 .6250 * 11.00 P
C-119 .6875 * 11.00 P
C-118 .7500 * 11.00 P
332 0.4375 12.00 5.44 P 4.650
380 0.5000 12.00 4.21 P 3.782
389 0.6250 12.00 2.29 P 3.286
355 0.8125 12.00 1.20 P 2.666
9-16-62 .5625 * 18.00 1.86 P 6.420
11-16-62 .6875 * 18.00 1.87 P 3.350
13-16-62 .8125* 18.00 1.25 P 2.790
0.063 020-094 0.3750 2.13 425.00 S&G 1.147
020-091 0.5000 2.50 18.00 S&G 1.000
020-051 0.5160 12.00 2.80 P 5.438
0.068 11-16-68 .6875 * 18.00 2.26 P 4.280
0.070 020-123 0.6000 1.50 40.00 S&G 0.560
0.072 020-087 .2810 X 0.91 56.00 SQ 0.522
(conical) 0.5310
020-060 0.5000 0.97 52.00 S&G 0.612
WIRE STOCK# OD FL RATE ENDS SOLID HT
WA-111 .6250 * 1.00 57.00 S&G 0.420
WA-112 .6250 * 1.50 34.00 S&G 0.585
415 0.5625 1.75 46.90 SQ 0.720
WA-113 .6250 * 2.00 32.00 S&G 0.810
16 0.6250 2.00 38.07 SQ 0.648
WA-114 .6250 * 2.50 26.00 S&G 0.920
WA-115 .6250 * 3.00 20.00 S&G 1.070
C-12 .6250 * 3.00 17.50 SQ
WA-116 .6250 * 3.50 18.00 S&G 1.280
C-13 .6250 * 4.00 11.00 SQ
WA-117 .6250 * 4.00 16.00 S&G 1.600
60 0.6875 9.50 4.61 SQ 2.808
C-4 .6250 * 10.00 5.70 P
360 0.6875 12.00 3.19 P 3.816
9-16-72 .5625 * 18.00 5.30 P 5.180
11-16-72 .6875 * 18.00 3.17 P 4.210
0.075 3-8-75 .3750 * 10.00 27.77 P 5.250
7-16-75 .4380 * 10.00 19.81 P 4.130
1-2-75 .500 * 10.00 15.03 P 3.380
0.080 020-058** .6250 X 1.00 33.45 S&G 0.440
(conical) 0.7500
020-070** 0.844 1.09 21.50 S&G 0.360
39 0.6875 1.50 65.81 SQ 0.560
020-063 0.9380 2.03 16.00 S&G 0.640
35 0.6875 2.38 77.54 SQ 1.280
020-068 0.6250 2.84 30.00 S&G 1.080
020-107 0.7500 3.35 16.00 DB
47 0.8750 3.44 11.71 SQ 1.040
C-14 .7500 * 3.50 19.00 SQ
525 0.7500 4.00 SQ
C-15 .7500 * 4.50 10.00 SQ
48 0.4375 5.00 34.97 SQ 3.040
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196416
®
EASY SPRING SELECTORCOMPRESSION
WIRE STOCK# OD FL RATE ENDS SOLID HT
0.080 020-048 0.8750 10.00 3.20 P 3.000
C-5 .7500 * 10.00 6.50 P
C-117 .5000 * 11.00 P
C-116 .6250 * 11.00 P
C-115 .7500 * 11.00 P
C-114 .8750 * 11.00 P
C-113 1.000 * 11.00 P
C-112 1.250 * 11.00 P
020-049 0.7340 12.00 3.80 P 4.880
347 0.9062 12.00 2.68 P 3.200
13-16-80 .8120 * 18.00 3.85 P 3.600
15-16-80 .9380 * 18.00 14.52 P 6.190
0.085 7-16-85 .4380 * 10.00 31.15 P 5.100
17-16-85 1.062* 18.00 2.21 P 7.290
0.090 19-16-90 1.188 * 18.00 2.77 P 2.840
0.091
14 0.6250 1.75 99.59 SQ 0.864
413 0.6250 1.75 99.59 SQ 0.864
1-2-91 .5000 * 10.00 32.54 P 4.550
299-A 0.7500 12.00 8.20 P 3.913
0.092 020-064 0.8750 3.06 21.80 S&G 1.098
C-111 .6250 * 11.00 P
C-110 .7500 * 11.00 P
C-109 1.000 * 11.00 P
C-108 1.125 * 11.00 P
C-107 1.250 * 11.00 P
C-106 1.375 * 11.00 P
0.098 020-106 0.8750 6.00 12.20 DB
7-8-98 .8750 * 18.00 14.52 P 6.190
8-8-98 1.000 * 18.00 5.72 P 3.440
0.102 020-109 0.5620 4.38 42.15 S&G 2.344
0.105 020-059 0.5310 1.03 436.00 SQ 0.950
57 0.7500 3.00 59.19 SQ 1.470
49 0.9690 3.75 27.18 SQ 1.365
020-067 0.6880 4.06 158.00 S&G 1.952
529 1.0000 6.00 SQ
C-105 .7500 * 11.00 P
C-104 1.000 * 11.00 P
C-103 1.125 * 11.00 P
020-047 0.8750 12.00 8.00 P 5.170
349 1.0000 12.00 7.17 P 3.675
0.106 020-072 0.7500 2.62 66.40 S&G 1.166
0.115 1-2-115 .5000 * 10.00 91.47 P 6.330
0.120 020-065 0.8750 2.00 110.00 S&G 0.964
020-062 1.0150 2.56 56.00 S&G 1.148
58 1.2500 4.62 20.65 SQ 1.560
56 1.0310 5.37 28.06 SQ 2.040
61 0.9380 9.87 20.24 SQ 3.600
WIRE STOCK# OD FL RATE ENDS SOLID HT
C-102 1.125 * 11.00 P
C-101 1.250 * 11.00 P
C-100 1.500 * 11.00 P
299-C 0.8750 12.00 22.34 P 3.840
0.125 020-115 0.7190 0.87 550.00 S&G 0.625
020-120 1.3120 1.25 92.12 SQ 0.687
020-114 0.7500 1.75 220.00 S&G 1.063
15-16-125 .9380 * 18.00 14.52 P 6.190
17-16-125 1.062 * 18.00 13.61 P 4.500
9-8-125 1.125 * 18.00 7.89 P 3.600
19-16-125 1.188 * 18.00 9.10 P 4.500
0.135 020-066 0.8590 2.59 154.00 S&G 1.485
59 1.0000 3.75 67.06 SQ 1.890
367 1.0000 12.00 30.74 P 3.375
369 1.2500 12.00 19.14 P 2.565
9-8-135 1.125 * 18.00 9.98 P 6.190
.141 X 0.187
020-124 0.9060 0.75 1632.00 S&G 0.494
0.145 020-122 0.9950 2.50 130.00 S&G 1.400
0.148 020-121 0.6880 1.06 1230.00 S&G 0.814
11-8-148 1.375 * 18.00 12.83 P 4.460
13-8-148 1.625 * 18.00 8.09 P 3.990
15-8-148 1.875 * 18.00 4.66 P 4.660
0.162 371 1.5000 12.00 22.96 P 3.078
0.187 373 1.5000 12.00 45.68 P 3.366
0.205 375 1.7500 12.00 34.42 P 4.305
0.207 020-119 0.9380 1.00 2800.00 S&G 0.880
0.225 020-118 1.1720 1.06 2400.00 S&G 0.845
0.281 020-117 1.4680 1.25 3960.00 S&G 1.124
LEGEND
** DENOTES BRASS SPRING * DENOTES HOLE DIAMETER P PLAIN ENDS NOT SQUARED OR GROUND S&G SQUARED AND GROUND ENDS SQ SQUARED ENDS DB DRAW BAR SPRING
Can’t find what you are lookin for?Give us a call; we’ll have it made to your specs.
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 17
®
EASY SPRING SELECTOREXTENSION
P STOCK# OD FL RATE ENDS
0.014 020-042 0.188 1.00 0.19 P
E-229 0.250 11.00 P
0.016 020-137 0.120 0.62 3.30 FLC
020-138 0.120 0.75 2.50 FLC
020-139 0.120 0.88 2.00 FLC
0.018 E-228 0.250 11.00 P
0.020 E-6 0.250 1.00 0.88 FLC
020-040 0.234 1.12 0.75 FLC
E-7 0.250 1.50 0.47 FLC
1 0.156 1.87 1.13 FLS
502 0.187 2.00 FLC
441 0.344 2.00 0.26 LHC
020-035** 0.156 2.06 0.50 FLC
93X 0.250 2.31 0.28 FLC
504 0.250 2.50 FLC
404 0.281 2.50 0.13 FLC
E-227 0.250 11.00 P
E-226 0.312 11.00 P
0.022 020-140 0.180 1.00 2.80 FLC
020-141 0.180 1.12 2.40 FLC
020-142 0.180 1.25 2.00 FLC
440 0.312 2.50 0.34 LHC
0.025 158 0.250 0.75 DFL
111-D 0.250 0.87 2.99 DFL
0.026 020-143 0.240 1.37 1.80 FLC
020-144 0.240 1.50 1.60 FLC
020-145 0.240 1.75 1.30 FLC
020-011 0.156 6.62 1.81 FLC
E-225 0.250 11.00 P
E-224 0.312 11.00 P
E-223 0.375 11.00 P
0.028 168 ** 0.312 1.25 DFL
75X 0.234 1.50 2.91 FLC
020-020 0.250 4.00 0.81 FLC
020-017 0.250 5.75 0.59 FLC
0.029 81X 0.187 1.68 5.67 FLC
406 0.250 1.87 1.76 FLC
401 0.187 2.00 3.85 FLC
020-008 0.172 9.06 1.00 FLC
0.032 111-A 0.312 1.25 3.70 DFL
83X 0.218 2.00 4.70 FLC
70X 0.312 2.12 1.43 FLC
3 0.250 2.25 2.36 FLS
508 0.312 2.50 FLC
E-222 0.250 11.00 P
E-221 0.312 11.00 P
E-220 0.375 11.00 P
E-219 0.500 11.00 P
P STOCK# OD FL RATE ENDS
0.034 E-1 0.250 10.00 0.65 P
0.035 6 0.375 2.00 1.58 FLC
91X 0.281 2.43 2.75 FLS
2 0.250 2.50 3.86 DFL
506 0.250 2.50 FLC
403 0.250 3.00 3.08 FLC
512 0.375 3.00 FLC
51 0.344 4.00 1.10 LHC
020-016 0.266 6.12 1.10 FLS
020-010 0.328 6.50 0.58 FLC
302 0.250 12.00 0.63 P
351 0.344 12.00 0.21 P
306 0.375 12.00 0.16 P
352 0.437 12.00 0.10 P
0.036 162 ** 0.312 0.81 FLS
160 ** 0.250 0.87 DFL
0.037 020-146 0.360 1.50 3.40 FLC
020-147 0.360 1.75 2.89 FLC
020-148 0.360 2.00 2.20 FLC
86X 0.188 2.00 7.97 FLC
0.040 020-039** 0.300 1.13 5.25 FLC
E-8 0.375 1.50 5.25 FLC
E-9 0.375 2.00 3.00 FLC
0.041 111B ** 0.281 1.06 28.21 DFL
78X 0.312 1.68 7.30 FLC
88X 0.375 2.00 3.97 FLC
445 0.312 2.06 8.72 LHC
68X 0.312 2.18 5.50 FLC
100X 0.468 2.25 1.60 FLS
510 0.312 2.50 FLC
4 0.312 2.68 3.89 FLS
10 0.406 2.75 1.74 FLS
410 0.406 2.75 1.74 FLS
020-019 0.375 3.25 1.90 FLC
36 0.312 3.43 2.96 FLS
516 0.500 3.50 FLC
30 0.500 3.81 0.58 FLS
46 0.656 4.87 0.18 FLS
020-026 0.312 5.00 5.23 FLC
020-018 0.250 5.34 4.30 FLC
520 0.625 6.00 FLC
38 0.281 6.50 2.02 FLS
E-218 0.312 11.00 P
E-217 0.375 11.00 P
E-216 0.500 11.00 P
E-215 0.625 11.00 P
310 0.375 12.00 0.37 P
330 0.500 12.00 0.14 P
346 0.656 12.00 0.06 P
P STOCK# OD FL RATE ENDS
020-152 0.297 16.00 0.70 DFL
0.042 442 0.218 1.75 38.96 LHC
402 0.250 2.34 9.94 FLC
0.047 443 0.250 1.68 56.06 LHC
97X 0.375 2.18 6.84 FLC
11 0.375 2.68 4.78 FLS
514 0.375 3.00 FLC
29 0.437 3.68 1.88 FLS
52 0.437 5.00 2.26 LHC
532 0.468 6.00 LHC
50 0.468 6.75 1.35 LHC
020-006 0.375 10.00 1.32 FLC
E-214 0.375 11.00 P
E-213 0.500 11.00 P
E-212 0.625 11.00 P
E-211 0.750 11.00 P
329 0.437 12.00 0.47 P
350 0.468 12.00 0.37 P
0.048 020-037 0.344 1.44 15.00 FLC
E-10 0.500 2.50 2.40 FLC
E-11 0.500 3.00 2.00 FLC
020-027 0.344 5.37 2.60 FLC
020-015 0.297 5.75 4.40 FLS
020-009 0.438 6.43 1.10 FLC
020-007 0.344 8.12 1.60 FLC
E-2 0.375 10.00 1.06 P
020-153 0.344 16.00 0.98 DFL
0.049 444 0.218 2.18 57.83 LHC
0.051 164 ** 0.312 1.09 DFL
166 ** 0.281 1.15 DFL
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196418
®
EASY SPRING SELECTOREXTENSION
WIRE STOCK# OD FL RATE ENDS
0.054 73X 0.437 1.94 12.41 FLC
8 0.468 2.44 6.43 FLS
408 0.468 2.44 6.43 FLS
020-014 0.375 5.50 4.00 FLC
447 0.344 6.87 9.91 LHC
020-005 0.359 10.00 2.30 FLC
020-154 0.375 16.00 1.34 DFL
0.062 66X 0.375 2.19 31.84 FLC
5 0.500 2.31 11.93 FLS
405 0.500 2.31 11.93 FLS
9 0.437 2.93 12.88 FLC
409 0.437 2.93 12.88 FLC
426 0.500 3.50 8.42 FLC
518 0.500 3.50 FLC
E-12 0.625 3.50 3.50 FLC
27 0.500 3.62 6.26 DFL
E-13 0.625 4.00 2.80 FLC
020-025 0.531 5.25 1.91 SW
40 0.656 5.37 1.47 DTL
522 0.625 6.00 FLC
020-112 0.734 6.00 0.93 FLC
448 0.500 6.12 5.97 LHC
449 0.343 7.50 17.91 LHC
62 0.500 9.75 1.80 DFL
E-3 0.500 10.00 1.60 P
020-004 0.500 10.00 2.09 FLC
E-210 0.500 11.00 P
E-209 0.625 11.00 P
E-208 0.750 11.00 P
E-207 1.000 11.00 P
362 0.500 12.00 1.31 P
340 0.625 12.00 0.62 P
0.063 020-023 0.734 4.06 1.73 FLC
020-022 0.484 4.50 6.20 FLC
020-028 0.438 5.25 6.50 FLC
020-155 0.422 16.00 2.20 DFL
0.072 914 0.500 1.62 MH
446 0.562 3.62 6.80 LHC
53 0.562 3.94 8.43 FLS
450 0.562 6.62 9.49 LHC
E-4 0.625 10.00 1.50 P
020-003 0.625 10.00 2.10 FLC
020-002 0.812 10.00 0.75 FLC
020-156 0.438 16.00 4.06 FLC
0.080 020-034 0.500 1.62 74.93 MH
1114 0.500 1.68 MH
020-033 0.750 2.65 10.30 MH
E-14 0.750 5.00 5.00 FLC
020-013 0.562 5.50 10.50 MH
WIRE STOCK# OD FL RATE ENDS
020-012 0.547 5.62 10.00 FLC
44 0.625 5.87 6.23 FLC
42 0.500 6.00 12.81 DTL
524 0.750 6.00 FLC
E-15 0.750 6.00 4.00 FLC
020-111 0.750 6.25 3.30 FLC
E-5 0.750 10.00 1.70 P
E-206 0.625 11.00 P
E-205 0.750 11.00 P
E-204 1.000 11.00 P
020-158 0.984 15.12 0.47 MH
0.091 63 0.750 10.25 28.75 LHC
363 0.750 12.00 2.63 P
0.092 020-116 0.906 6.75 3.00 FLC
020-001 0.875 10.00 2.50 MH
E-203 0.750 11.00 P
E-202 1.000 11.00 P
0.105 34 0.750 1.75 108.52 MH
432 0.750 1.75 108.52 MH
526 0.750 1.75 MH
612 0.750 1.75 MH
31 0.750 1.93 81.39 MH
433 0.750 1.93 81.39 MH
434 0.750 2.18 68.11 MH
1012 0.750 2.18 MH
28 0.750 2.31 54.26 MH
435 0.750 2.31 54.26 MH
528 0.750 2.37 MH
020-032 0.750 2.59 46.00 MH
436 0.750 2.62 46.51 MH
1412 0.750 2.62 MH
437 0.750 2.81 40.69 MH
1612 0.750 2.81 MH
530 0.750 3.00 MH
020-097 0.750 3.00 41.03 MH
438 0.750 3.00 36.17 MH
1812 0.750 3.00 MH
439 0.750 3.37 31.00 MH
2112 0.750 3.37 MH
2512 0.750 3.81 MH
020-099 0.688 3.87 32.83 MH
020-024 0.719 4.00 30.78 MH
210 0.750 5.50 17.55 FLC
64 0.750 8.00 10.90 FLC
020-031 1.000 8.50 3.96 MH
E-201 0.750 11.00 P
E-200 1.000 11.00 P
366 0.875 12.00 3.38 P
020-108 1.125 16.00 3.00 DFL
WIRE STOCK# OD FL RATE ENDS
0.107 020-095 0.718 2.00 90.86 MH
0.113 020-113 0.625 4.00 70.00 FLC
0.120 020-029 0.875 6.00 18.50 MH
368 1.000 12.00 4.42 P
0.128 534 1.125 5.75 MH
0.135 020-030 1.062 8.00 13.48 MH
370 1.250 12.00 3.92 P
372 1.500 12.00 2.14 P
0.148 020-100 1.125 10.00 14.00 MH
0.162 020-101 1.250 12.00 12.60 MH
0.177 020-102 1.375 14.00 13.00 MH
0.187 374 1.750 12.00 7.29 P
376 2.000 12.00 4.67 P
0.207 020-104 1.250 7.62 13.48 MH
020-103 1.562 16.00 16.50 MH
0.250 020-105 1.812 8.18 65.00 MH
LEGEND
DFL DENOTES DOUBLE FULL LOOP CENTEREDDTL DENOTES DOUBLE TWISTED FULL LOOP OVER CENTERFLC DENOTES FULL LOOP FROM CENTER FLS DENOTES FULL LOOP FROM SIDE LHC DENOTES LONG ROUND END HOOk OVER CENTERMH DENOTES MACHINE HOOkS P DENOTES PLAIN ENDS WITHOUT HOOk OR LOOPSW DENOTES SWIVEL HOOkS ** DENOTES BRASS SPRINGS
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 19
®
SPRINGBOXED ASSORTMENTS
Stock Number
Wire O.D. Spring Rate
Max Load
377 0.032 0.375 .373 3.275
299B 0.047 0.593 .640 5.639
337 0.047 0.500 1.500 7.923
345 0.047 0.750 .388 3.692
332 0.062 0.437 5.443 19.051
355 0.062 0.812 1.198 10.789
380 0.062 0.500 4.213 16.852
389 0.062 0.625 2.289 13.734
360 0.072 0.687 3.186 19.116
347 0.080 0.906 2.676 19.404
299A 0.091 0.750 8.201 33.829
349 0.105 1.000 7.168 37.633
299C 0.120 0.875 22.342 61.441
367 0.135 1.000 30.738 74.940
369 0.135 1.250 19.135 61.004
371 0.162 1.500 22.962 86.110
373 0.187 1.500 45.680 125.621
375 0.205 1.750 34.419 141.981
Springs may be ordered individually
Stock Number
Wire O.D. Spring Rate
Max Load
302 0.035 0.250 .634 6.501
306 0.035 0.375 .160 4.552
351 0.035 0.344 .214 4.960
352 0.035 0.438 .097 3.888
310 0.041 0.375 .373 7.133
330 0.041 0.500 .144 5.388
346 0.041 0.656 .059 4.098
329 0.047 0.438 .465 8.870
350 0.047 0.469 .367 8.261
340 0.062 0.625 .618 13.608
362 0.062 0.500 1.312 16.677
363 0.091 0.750 2.632 33.385
366 0.105 0.875 3.378 42.198
368 0.120 1.000 4.418 54.061
370 0.135 1.250 3.919 60.500
372 0.135 1.500 2.136 108.941
374 0.187 1.750 7.287 108.941
376 0.187 2.000 4.669 95.903
Springs may be ordered individually
Stock Number Hole Diameter Free Length Wire Diameter Maximum Pressure Load to Deflect 1/8” in Pounds
WA100 3/8” 1” .042 10 lbs. 2-1/2
WA101 3/8” 1-1/2” .042 10 lbs. 1-1
WA102 3/8” 2” .042 10 lbs. 1
WA103 3/8” 2-1/2” .042 10 lbs. 3/4
WA104 3/8” 3” .042 10 lbs. 1/2
WA105 1/2” 1” .062 20 lbs. 5
WA106 1/2” 1-1/2” .062 20 lbs. 3
WA107 1/2” 2” .062 20 lbs. 2-1/2
WA108 1/2” 2-1/2” .062 20 lbs. 2-1/4
WA109 1/2” 3” .062 20 lbs. 2
WA110 1/2” 3-1/2” .062 20 lbs. 1-3/4
WA111 5/8” 1” .072 30 lbs. 7-1/2
WA112 5/8” 1-1/2” .072 30 lbs. 5
WA113 5/8” 2” .072 30 lbs. 3-1/2
WA114 5/8” 2-1/2” .072 30 lbs. 3
WA115 5/8” 3” .072 30 lbs. 2-3/4
WA116 5/8” 3-1/2” .072 30 lbs. 2-1/2
WA117 5/8” 4” .072 30 lbs. 2
400 Pc. Spring Assortment - Set No. 400Metal Wall Display with 50 Mounted Springs! 2-Drawer Metal Cabinet with 52 Compartments.• 400 Springs: 50 different numbers contained
in a neatly compartmented 2-drawer steel cabinet
• Each compartment is clearly numbered to correspond with the actual numbered items mounted on the metal display
• Assortment includes springs for windshield wipers, stoves, gliders, lawnmowers, outdoor furniture...as well as a multitude of other uses
• Cabinet Size: 8” H x 20” W x 12” D• Approx. shipping weight: 40 lbs
250 Pc. Spring Assortment - Set No. 250Includes Plastic Cabinet & Photo Display Card Consists of:• FREE Plastic Cabinet with 15 plastic drawers• 250 springs (27 different types)• Colorful counter display card which can also
be hung on the wall• Springs are ideal for countless, varied uses.
Compact cabinet has compartmented drawers, clearly numbered for ease of dispensing.
• Cabinet size: 7 1⁄4” H x 9” W x 6 1⁄2” D
1,000 Pc. Spring Assortment - Set No. 750A Complete Spring Department in 2 Sq. Ft. of Shelf Space.Includes Free metal display with springs and 4-drawer matching metal cabinet.• Assortment includes a spring for every need
- sizes No. 1 to 100X• Springs are neatly contained in 4-drawer
cabinet with numbered compartments• Cabinet size: 15” H x 20” W x 16” D• Approx. shipping weight: 90 Lbs• Convenient cabinet size to fit most all MRO
work areas.
Compression Spring Assortment Set - No. 299Can be cut to any desired size reorders of individual springs can be refilled.Wire Size: .032” to .205”Spring Diameter: 3/8” to 1 3/4”Length: 12”18 pieces
Extension Spring Assortment Set - No. 300Can be cut to any size, reorders of individual springs can be refilled.Wire Size: .035" to .187"Spring Diameter: 1/4" to 2"Length: 12”18 pieces
Round Music Wire Springs - Medium Duty
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196420
®
For Spring Assortment #750, 400 & 250 REPLACEMENT SPRINGSEXTENSION – COMPRESSION – TORSION
Stock Type of Wire Outside Total Body Type of Spring Max. Nb Spring Size Diameter Length Length Ends Rate Load
1 E 0.020 0.156 1.875 1.625 A 1.13 1.87 2 E 0.035 0.250 2.500 2.000 CD 3.86 5.80 3 E 0.032 0.250 2.250 2.000 A 2.36 4.45 4 E 0.041 0.312 2.687 2.187 A 3.89 7.23 5 E 0.062 0.500 2.312 1.375 A 11.93 14.74 6 E 0.035 0.375 2.000 1.250 B 1.58 3.74 7 CC 0.041 .40x.68 1.000 NA Z 8 E 0.054 0.468 2.437 1.500 A 6.43 10.43 9 E 0.062 0.437 2.937 2.000 B 12.88 16.77 10 E 0.041 0.406 2.750 2.000 A 1.74 5.35 11 E 0.047 0.375 2.687 2.000 A 4.78 8.77 12 DC 0.047 .43x.68 2.000 NA Z 13 C 0.054 0.500 1.750 NA Z 13.77 14.43 14 C 0.091 0.625 1.750 NA Z 99.59 88.19 15 T 0.072 0.500 NA NA Y 16 C 0.072 0.625 2.000 NA Z 38.07 51.47 17 C 0.041 0.312 1.375 NA Z 29.14 28.13 18 C 0.020 0.312 1.500 NA Z .93 1.02 19 C 0.032 0.203 2.250 NA Z 8.37 8.39 20 C 0.015 0.218 1.625 NA Z .45 .59 21 C 0.022 0.187 1.312 NA Z 2.44 2.18 22 C 0.032 0.218 1.250 NA Z 15.61 10.52 23 C 0.026 0.312 1.875 NA Z 2.00 2.87 24 C 0.041 0.312 2.312 NA Z 13.60 21.41 25 C 0.023 0.250 2.000 NA Z 2.02 3.11 26 C 0.047 0.437 3.000 NA Z 8.44 18.59 27 E 0.062 0.500 3.625 2.562 CD 6.26 14.84 28 E 0.105 0.750 2.312 1.250 D 54.26 43.27 29 E 0.047 0.437 3.687 3.000 A 1.88 7.44 30 E 0.041 0.500 3.812 3.000 A .58 4.27 31 E 0.105 0.750 1.937 0.812 D 81.39 40.25 32 C 0.062 0.437 3.250 NA Z 22.37 43.59 33 C 0.047 0.328 3.312 NA Z 13.17 26.91 34 E 0.105 0.750 1.750 0.625 D 108.52 44.25 35 C 0.080 0.468 2.375 NA Z 77.54 84.90 36 E 0.041 0.312 3.437 2.875 A 2.96 7.26 37 C 0.047 0.468 1.125 NA Z 15.66 10.99 38 E 0.041 0.281 6.500 6.000 A 2.02 8.31 39 C 0.080 0.687 1.500 NA Z 65.81 61.86 40 E 0.062 0.640 5.375 4.375 ED 1.47 11.30 41 C 0.062 0.500 2.812 NA Z 13.30 19.26 42 E 0.080 0.500 6.000 5.000 ED 12.81 30.88 43 C 0.062 0.687 3.000 NA Z 7.25 15.00 44 E 0.080 0.625 5.875 4.750 F 6.23 23.00 45 C 0.047 0.750 3.375 NA Z 1.44 3.78 46 E 0.041 0.656 4.875 4.000 A .18 3.71 47 C 0.080 0.875 3.437 NA Z 11.71 28.08 48 C 0.080 0.437 5.000 NA Y 34.97 68.55 49 C 0.105 0.968 3.750 NA Z 27.18 64.83 50 E 0.047 0.468 6.750 3.312 G 1.35 6.92 51 E 0.035 0.343 4.000 2.375 G 1.10 4.11 52 E 0.047 0.437 5.000 2.125 G 2.26 7.48 53 E 0.072 0.562 3.937 2.875 A 8.43 19.70 54 C 0.041 0.468 5.250 NA Z 2.17 9.00 55 C 0.062 0.812 3.250 NA Z 3.35 7.16 56 C 0.120 1.032 5.375 NA Z 28.06 93.60 57 C 0.105 0.750 3.000 NA Z 59.19 90.57 58 C 0.120 1.250 4.625 NA Z 20.65 63.31 59 C 0.135 1.000 3.750 NA Z 67.06 124.74 60 C 0.072 0.687 3.750 NA Z 4.61 30.87 61 C 0.120 0.937 9.500 NA Z 20.24 127.03
Stock Type of Wire Outside Total Body Type of Spring Max. Nb Spring Size Diameter Length Length Ends Rate Load
62 E 0.062 0.500 9.750 8.750 CD 1.80 14.6263 E 0.091 0.750 10.250 3.562 G 9.03 28.7564 E 0.105 0.750 8.000 6.375 B 10.90 44.1265 C 0.041 0.625 2.687 NA Z 1.56 3.8266X E 0.062 0.375 2.187 1.437 B 31.84 19.2467X C 0.028 0.328 1.125 NA Z 4.67 3.9568X E 0.041 0.312 2.187 1.562 B 5.50 7.2869X C 0.020 0.250 2.000 NA Z .82 1.2170X E 0.032 0.312 2.125 1.562 B 1.43 3.4871X C 0.020 0.187 1.500 NA Z 2.24 2.2472X C 0.022 0.250 1.875 NA Z 1.81 2.4773X E 0.054 0.437 1.937 1.000 B 12.41 11.06 74X C 0.025 0.312 1.437 NA Z 1.75 1.8075X E 0.028 0.234 1.500 1.000 B 2.91 3.1676X C 0.041 0.312 2.000 NA Z 14.57 18.9977X C 0.035 0.375 1.437 NA Z 3.70 4.2278X E 0.041 0.312 1.687 1.187 B 7.30 7.1479X C 0.041 0.375 1.937 NA Z 10.90 15.3080X C 0.062 0.500 1.437 NA Z 42.13 37.0381X E 0.028 0.187 1.687 1.250 B 5.67 3.9682X C 0.047 0.500 1.750 NA Z 10.77 13.7983X E 0.032 0.218 2.000 1.625 B 4.70 5.3284X C 0.041 0.437 1.437 NA Z 5.45 4.8085X C 0.054 0.625 1.562 NA Z 6.66 5.6486X E 0.037 0.187 2.000 1.625 B 7.97 13.5287X C 0.032 0.234 1.750 NA Z 12.19 14.3188X E 0.041 0.375 2.000 1.187 B 3.97 5.9189X C 0.062 0.625 2.000 NA Z 14.47 19.6090X C 0.035 0.312 1.500 NA Z 7.24 6.5691X E 0.035 0.281 2.437 1.875 A 2.76 5.1892X C 0.032 0.312 1.687 NA Z 5.72 7.6293X E 0.020 0.250 2.312 1.875 B .28 1.1094X C 0.025 0.250 2.000 NA Z 2.59 3.7695X C 0.047 0.312 1.500 NA Z 24.97 31.4196X C 0.047 0.375 1.500 NA Z 15.29 11.4397X E 0.047 0.375 2.187 1.437 B 6.84 8.9298X C 0.032 0.250 1.437 NA Z 14.54 14.8599X C 0.026 0.375 1.875 NA Z 1.00 1.48100X E 0.041 0.468 2.250 1.375 A 1.60 4.60111A E 0.032 0.312 1.250 0.625 CD 3.70 3.33111B E 0.041 0.281 1.062 0.468 CD 28.21 8.99111D E 0.026 0.250 0.875 0.437 CD 2.99 2.11112 C 0.028 0.250 1.937 NA Z 5.04 7.09115 C 0.011 0.156 2.000 NA Z .23 .39116 C 0.031 0.250 1.312 NA Z 14.54 14.85120 C 0.015 0.218 1.625 NA Z .45 .59122 C 0.041 0.375 1.156 NA Z 12.11 8.04123 C 0.026 0.250 2.625 NA Z 1.82 1.42124 C 0.041 0.218 1.500 NA Z 61.04 64.02 125 C 0.256 0.281 2.312 NA Z 2.09 3.84126 C 0.020 0.187 0.875 NA Z 3.08 1.52
BRASS WIRE SPRINGS #157 TO #162 Stock Type of Wire Outside Total Body Type of Spring Max. Nb Spring Size Diameter Length Length Ends Rate Load 157 C 0.025 0.187 2.250 NA Z - - 158 E 0.025 0.250 0.750 0.250 CD - - 159 C 0.021 0.250 2.500 NA Z - - 160 E 0.036 0.250 0.875 0.375 A - - 161 C 0.017 0.250 2.000 NA Z - - 162 E 0.036 0.312 0.812 0.312 CD - -
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 21
®
REPLACEMENT SPRINGS For Spring Assortment #750, 400 & 250
EXTENSION – COMPRESSION – TORSION
Stock Type of Wire Outside Total Body Type of Spring Max. Nb Spring Size Diameter Length Length Ends Rate Load
BRASS WIRE SPRINGS #163 TO #168163 C 0.036 0.250 2.500 NA Z - - 164 E 0.051 0.312 1.093 0.500 CD - -165 C 0.028 0.281 2.312 NA Z - -166 E 0.051 0.281 1.156 0.562 CD - -167 C 0.043 0.312 2.375 NA Z - -168 E 0.028 0.312 1.250 0.687 CD - -
200 T 0.032 0.250 NA 0.375 Y - -210 E 0.105 0.750 5.500 4.000 B 17.55 44.24401 E 0.028 0.187 2.000 1.625 B 3.85 4.09402 E 0.041 0.250 2.343 1.875 B 9.94 7.97403 E 0.035 0.250 3.000 2.500 B 3.08 3.08404 E 0.020 0.281 2.500 2.000 B .13 .99405 E 0.062 0.500 2.312 1.375 A 11.93 14.74406 E 0.028 0.250 1.875 1.312 B 1.76 3.01407 CC 0.041 .40x.68 1.000 NA Z - -408 E 0.054 0.468 2.437 1.500 A 6.43 10.43409 E 0.062 0.437 2.937 2.000 B 12.88 15.77410 E 0.041 0.406 2.750 2.000 A 1.74 5.35411 DC 0.054 .31x.56 2.000 NA Z - -412 C 0.047 0.437 1.750 NA Z 11.82 13.46413 C 0.091 0.625 1.750 NA Z 99.59 88.19414 T 0.072 0.500 NA NA Z - -415 C 0.072 0.562 1.750 NA Z 46.90 48.31416 C 0.041 0.312 1.375 NA Z 29.14 28.13417 C 0.020 0.312 1.500 NA Z .93 1.02418 C 0.032 0.203 2.250 NA Z 8.37 8.39419 C 0.015 0.218 1.625 NA Z .46 .59420 C 0.023 0.187 1.312 NA Z 2.44 2.18421 C 0.020 0.187 1.125 NA Z 4.11 3.39422 C 0.026 0.312 1.875 NA Z 2.00 2.87423 C 0.041 0.312 2.312 NA Z 13.60 21.41424 C 0.023 0.250 2.000 NA Z 2.02 3.11425 C 0.047 0.437 3.000 NA Z 8.44 18.59426 E 0.062 0.500 3.500 2.500 Z 6.42 14.74427 C 0.028 0.328 1.125 NA Z 4.67 3.95428 C 0.047 0.312 1.500 NA Z 24.97 31.41429 C 0.020 0.250 2.000 NA Z .82 1.21430 C 0.025 0.312 1.437 NA Z 1.75 1.80431 C 0.032 0.250 1.437 NA Z 14.54 14.85432 E 0.105 0.750 1.750 0.625 D 108.52 44.25433 E 0.105 0.750 1.937 0.812 D 81.39 40.25434 E 0.105 0.750 2.187 1.062 D 68.11 42.00435 E 0.105 0.750 2.312 1.250 D 54.26 43.27436 E 0.105 0.750 2.625 1.500 D 46.51 43.96437 E 0.105 0.750 2.812 1.750 D 40.69 44.00438 E 0.105 0.750 3.000 1.875 D 36.17 44.81439 E 0.105 0.750 3.375 2.250 D 31.00 45.69440 E 0.022 0.312 2.500 1.125 G .34 1.32441 E 0.020 0.343 2.000 0.532 GB .26 .79442 E 0.041 0.218 1.750 0.812 G 38.95 11.32443 E 0.047 0.250 1.687 0.750 G 56.06 13.74444 E 0.047 0.218 2.187 1.187 G 57.83 15.62445 E 0.041 0.312 2.062 1.000 GB 8.72 7.02446 E 0.072 0.562 3.625 0.937 G 6.80 19.66447 E 0.054 0.343 6.437 2.812 G 9.91 15.03448 E 0.062 0.500 6.125 2.687 G 5.97 14.74449 E 0.062 0.343 7.500 3.375 G 17.91 22.02450 E 0.072 0.562 6.625 2.562 G 9.49 19.65
EXPLANATION OF CODESfor Replacement Springs
A = FULL LOOP FROM SIDE B = FULL LOOP FROM CENTER C = COMPRESSION CC = CONE COMPRESSION CD = DOUBLE FULL LOOP D = MACHINE HOOk DC = DOUBLE CONE E = EXTENSION ED = DOUBLE TWISTED FULL LOOP OVER CENTER G = LONG ROUND END HOOk OVER CENTER GB = LONG FULL LOOP OVER CENTER NA = NOT APPLICABLE T = TORSION Y = PLAIN END Z = SQUARED END
Stock Type of Wire Outside Total Body Type of Spring Max. Nb Spring Size Diameter Length Length Ends Rate Load
501 C 0.020 0.188 2.000 NA Z502 E 0.020 0.188 2.000 1.500 B503 C 0.020 0.250 2.000 NA Z504 E 0.020 0.250 2.500 2.000 B505 C 0.035 0.250 2.000 NA Z506 E 0.035 0.250 2.500 2.000 B507 C 0.032 0.312 2.000 NA Z508 E 0.032 0.312 2.500 1.875 B509 C 0.041 0.312 2.000 NA Z510 E 0.041 0.312 2.500 1.875 B511 C 0.035 0.375 3.000 NA Z512 E 0.035 0.375 3.000 2.250 B513 C 0.047 0.375 3.000 NA Z514 E 0.047 0.375 3.000 2.250 B515 C 0.041 0.500 3.000 NA Z516 E 0.041 0.500 3.500 2.500 B517 C 0.062 0.500 3.000 NA Z518 E 0.062 0.500 3.500 2.500 B519 C 0.041 0.625 4.000 NA Z520 E 0.041 0.625 6.000 4.750 B521 C 0.062 0.625 4.000 NA Z522 E 0.062 0.625 6.000 4.750 B523 C 0.047 0.750 4.000 NA Z524 E 0.080 0.750 6.000 4.500 B525 C 0.080 0.750 4.000 NA Z526 E 0.105 0.750 1.750 0.625 D527 C 0.062 1.000 6.000 NA Z528 E 0.105 0.750 2.375 1.250 D529 C 0.105 1.000 6.000 NA Z530 E 0.105 0.750 3.000 1.875 D532 E 0.047 0.468 6.000 3.312 G534 E 0.128 1.125 5.750 4.250 D612 E 0.105 0.750 1.750 0.625 D914 E 0.080 0.500 1.625 0.812 D1012 E 0.105 0.750 2.187 1.062 D1114 E 0.080 0.500 1.687 1.000 D1412 E 0.105 0.750 2.625 1.500 D1612 E 0.105 0.750 2.812 1.750 D1812 E 0.105 0.750 3.000 1.875 D2112 E 0.105 0.750 3.375 2.250 D2512 E 0.105 0.750 3.812 2.812 D
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196422
®
KALLER® GAS SPRINGS
SERIES Description
Model Available Stoke Lengths (mm)
Initial Force at Max Pressure
Total Length (mm)Cylinder Diameter (mm)(daN) (lbf)
EP2 Color coded gas Ejector-Pins that are fully interchangeable with mechanical spring plungers
EP2 16 10,20,30,40,50,60,70,80,100,125 42 94 45 + (2 x Stroke) M16x1.5/ 16x2
EP2 24 10,20,30,40,50,60,70,80,100,125 170 380 45 + (2 x Stroke) M24x1.5
EPS2 24 10,16,20,25,30,38,40,50,60,70,80,100,125 170 380 45 + (2 x Stroke) M24x1.5
“R” Rod Sealed and color coded gas springs that are compact and fully adjustable.
R12 7,10,12.7,15,19,25,38.1,50,63.5,75,80,100,125 50 110 42 or 45+ (2 x Stroke) Ø 12
R15 7,10,12.7,15,19,25,38.1,50,63.5,75,80,100,125 70 160 42 or 45 + (2 x Stroke) Ø 15
R19 7,10,15,25,38.1,50,63.5,80,100,125 90 200 42 or 45 + (2 x Stroke) Ø 19
Mini Repairable, color coded and fully adjustable gas springs. Available with or without threaded cylinders.
M2 10,12.7,15,16,25,38.1,50,63.5,80,100,125 200 450 42 or 45 + (2 x Stroke) Ø 25
MM2 10,12.7,15,16,25,38.1,50,63.5,80,100,125 200 450 42 +(2 x Stroke) M28x1.5
MC3 10,12.7,16,25,38.1,50,63.5,80,100,125 200 450 50 + (2 x Stroke) Ø 32
CU Super compact gas springs that provide extreme forces with minimal cylinder diameter.
CU 420 6,10,16,25,32,40,50 425 960 56 - 195 Ø 25
CU 740 6,10,16,25,32,40,50 740 1660 63 - 195 Ø 32
CU 1000 6,10,16,25,32,40,50 1060 2380 61 - 230 Ø 38
CU 1800 6,10,16,25,32,40,50 1800 4050 66 - 220 Ø 50
CU 2900 10,16,25,32,40,50, 2950 6630 85 - 205 Ø 63
CU 4700 10,16,25,32,40,50, 4700 10570 80 - 240 Ø 75
CU 7500 10,16,25,32,40,50, 7500 16860 90 - 255 Ø 95
CU 11800 10,16,25,32,40,50, 11800 26530 100 - 260 Ø 120
CU 18300 10,16,25,32,40,50, 18300 41140 110 - 270 Ø 150
Power-Line X The shortest, strongest and most advanced rod sealed gas springs.
X 170 7,10,15,19,25,38,50,63,75,80,100,125 170 380 30 or 35 + (2 x Stroke) Ø 19
X 320 7,10,15,19,25,38,50,63,75,80,100,125 320 720 30 or 35 + (2 x Stroke) Ø 25
X 350 10,13,16,19,25,32,38,50,63,75,80,100,125 360 810 30 + (2 x Stroke) Ø 32
X 500 10,13,16,19,25,32,38,50,63,75,80,100,125 470 1060 30 + (2 x Stroke) Ø 38
X 750 10,13,16,19,25,32,38,50,63,75,80,100,125 740 1660 32 + (2 x Stroke) Ø 45
X 1000 13,16,19,25,32,38,50,63,75,80,100,125 920 2070 38 + (2 x Stroke) Ø 50
X 1500 13,16,19,25,32,38,50,63,75,80,100,125 1500 3370 44 + (2 x Stroke) Ø 63
X 2400 16,19,25,32,38,50,63,75,80,100,125 2400 5400 45 + (2 x Stroke) Ø 75
X 4200 16,19,25,32,38,50,63,75,80,100,125 4200 9440 58 + (2 x Stroke) Ø 95
X 6600 16,19,25,32,38,50,63,75,80,100,125 6630 14910 68 + (2 x Stroke) Ø 120
X 9500 19,25,32,38,50,63,75,80,100,125 9500 21360 78 + (2 x Stroke) Ø 150
X 20 000 19,25,32,,38,50,63,75,80,100,125 20000 44960 110 + (2 x Stroke) Ø 195
TU Standard series – dimensions correspond to the ISO 11901 standard for gas springs.
TU 250 10,12.7,16,25,38.1,50,63.5,80,100,125 265 600 50 + (2 x Stroke) Ø 38
TU 500 10,12.7,25,38.1,50,63.5,80,100,125,160 470 1060 85 + (2 x Stroke) Ø 45
TU 750 12.7,25,38.1,50,63.5,80,100,125,160,200,250,300 740 1660 95 + (2 x Stroke) Ø 50
TU 1500 25,38.1,50,63.5,80,100,125,160,200,250,300 1500 3370 110 + (2 x Stroke) Ø 75
TU 3000 25,38.1,50,63.5,80,100,125,160,200,250,300 3000 6740 120 + (2 x Stroke) Ø 95
TU 5000 25,38.1,50,63.5,80,100,125,160,200,250,300 5000 11240 140 + (2 x Stroke) Ø 120
TU 7500 25,38.1,50,63.5,80,100,125,160,200,250,300 7500 16860 155 + (2 x Stroke) Ø 150
TU 10000 25,38.1,50,63.5,80,100,125,160,200,250,300 10600 23830 160 + (2 x Stroke) Ø 195
OTHER SERIES AVAILAbLE:
TX: Power Line - Heavy Duty series a crossover between standard TU series and Power Line X series.
SPC Series: Speed Control has been engineered to reduce or eliminate blank holder bounce commonly associated with increased return stroke, speeds from link drive presses. LCF Series: These innovative Low Contact Force series of gas spring are 100% interchangeable with ISO gas springs (ie. TU Series) and reduce shock loads, noise levels and pad bounce problems. Mould Temp - MT 16 to MT1000 - gas springs are compact and powerful piston rod sealed gas springs, which can be used up to 120°C.
Accessories, Mounts, Repair and Tool Kits available.
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 23
®
SCHNORR®DISC SPRINGS
Ref O.D. ‘D’
I.D. ‘d’
Thick ‘t’
Deflect ‘h’
Free Ht ‘h+t’
‘h/t’ P f = .25h P f = .5h P f = .75h P f = h Bolt Size
Stock Number
Z1 3/8 0.195 0.0157 0.0119 0.0276 0.758 22 0.0030 39 0.0060 53 0.0089 65 0.0119 3/16 DS-10
Z2 1/2 0.258 0.0196 0.0158 0.0354 0.806 33 0.0040 58 0.0079 76 0.0119 94 0.0158 1/4 DS-20
Z3 1/2 0.258 0.0236 0.0158 0.0394 0.670 52 0.0040 94 0.0079 130 0.0119 162 0.0158 1/4 DS-30
Z4 11/16 0.382 0.0236 0.0197 0.0433 0.835 42 0.0049 72 0.0099 95 0.0148 114 0.0197 3/8 DS-60
Z5 11/16 0.382 0.0275 0.0197 0.0472 0.717 61 0.0049 108 0.0099 147 0.0148 181 0.0197 3/8 DS-70
Z6 3/4 0.320 0.0275 0.0237 0.0512 0.863 57 0.0059 99 0.0119 130 0.0178 155 0.0237 5/16 DS-40
Z7 3/4 0.320 0.0315 0.0236 0.0551 0.750 79 0.0059 141 0.0118 189 0.0177 232 0.0236 5/16 DS-50
Z8 3/4 0.382 0.0315 0.0217 0.0532 0.690 76 0.0054 135 0.0109 187 0.0163 232 0.0217 3/8 DS-80
Z9 3/4 0.382 0.0354 0.0217 0.0571 0.613 102 0.0054 187 0.0109 262 0.0163 330 0.0217 3/8 DS-90
Z10 1 0.445 0.0354 0.0316 0.0670 0.893 96 0.0079 164 0.0158 213 0.0237 252 0.0316 7/16 DS-100
Z11 1 0.445 0.0394 0.0315 0.0709 0.800 123 0.0079 214 0.0158 285 0.0236 346 0.0315 7/16 DS-110
Z12 1 0.445 0.0492 0.0256 0.0748 0.520 175 0.0064 316 0.0128 438 0.0192 548 0.0256 7/16 DS-120
Z12a 1-1/10 0.512 0.0394 0.0354 0.0748 0.899 126 0.0088 214 0.0177 276 0.0266 326 0.0354 1/2 DS-130
Z12b 1-1/10 0.512 0.0492 0.0335 0.0827 0.680 198 0.0084 355 0.1680 485 0.0251 600 0.0335 1/2 DS-140
Z12c 1-1/10 0.512 0.0590 0.0275 0.0866 0.466 247 0.0069 467 0.0138 664 0.0206 853 0.0275 1/2 DS-150
Z13 1-3/8 0.637 0.0492 0.0453 0.0945 0.920 204 0.0113 346 0.0227 444 0.0340 524 0.0453 5/8 DS-160
Z14 1-3/8 0.637 0.0590 0.0434 0.1024 0.736 388 0.0109 629 0.0217 772 0.0326 865 0.0434 5/8 DS-170
Z15 1-3/8 0.637 0.0787 0.0316 0.1103 0.402 412 0.0079 790 0.0158 1144 0.0237 1492 0.0316 5/8 DS-180
Z16 1-1/2 0.761 0.0590 0.0551 0.1141 0.935 381 0.0138 642 0.0276 825 0.0413 970 0.0551 3/4 DS-190
Z17 1-1/2 0.761 0.0787 0.0433 0.1220 0.550 541 0.0108 1050 0.0217 1419 0.0325 1810 0.0433 3/4 DS-200
Z18 1-1/2 0.761 0.0983 0.0355 0.1338 0.361 783 0.0089 1518 0.0178 2210 0.0267 2895 0.0355 3/4 DS-210
Z19 2 1.016 0.0787 0.0590 0.1377 0.750 475 0.0148 841 0.0295 1132 0.0443 1386 0.0590 1 DS-220
Z20 2 1.016 0.0983 0.0591 0.1574 0.602 837 0.0148 1540 0.0296 2155 0.0443 2720 0.0591 1 DS-230
Z21 2 1.016 0.1181 0.0472 0.1653 0.400 1035 0.0118 1980 0.0236 2870 0.0354 3740 0.0472 1 DS-240
Z22 2-3/8 1.016 0.0787 0.0787 0.1574 1.000 609 0.0197 829 0.0394 1045 0.0590 1208 0.0787 1 DS-250
Z23 2-3/8 1.016 0.0983 0.0787 0.1770 0.801 836 0.0197 1460 0.0394 1943 0.0590 2355 0.0787 1 DS-260
SCHNORR PRECISION DISC SPRINGS Pressure P in pounds Deflection f in inch
FEATURESDisc springs have a simple circular shape and cannot tangle. Disc springs do not require special packaging or handling and are very well suited for feeding in automatic assembly operations.
Disc springs require less volume than coil springs of equivalent energy absorbing capacity.
Because of their unique shape, disc springs lend themselves to stacking in parallel, series, or series-parallel combinations. This feature allows systems of standard springs to be assembled to achieve the required force/deflection characteristics without having to resort to special designs.
If one coil of a coil spring breaks, the spring usually is useless and has to be replaced. In the unlikely failure of one disc spring in a stack, the remaining springs continue to function and the operation may continue satisfactorily until it is convenient to replace the broken disc.
In applications that require a spring to rotate at very high speeds, disc springs offer good resistance to the effects of centrifugal force.
Disc springs provide high load-bearing capacity in confined spaces that would require hydraulic or special designs with conventional springs.
Original SCHNORR® Safety Washers type “S”• The “S” Series is suitable for normal duty
and available for screws of size M1.6 to M36.
• Available in Carbon steel SAE 1060, Stainless steel and Phosphor bronze
• Available finishes: phosphate (stock), zinc-plated – clear, zinc-plated – yellow and stainless steel
For more details specifications and deflections on the SCHNORR® Disc Springs and Safety Washers
visit our website: http://productodiemakers.com/schnorr.html or call our Customer Service department.
When ordering please specify OD, ID and thickness.
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196424
®
SCHNORR®DISC SPRINGS
mm Size Inch Size Inch Dimension Deflect /
O.D. I.D. Thick O.D. I.D. Thick Deflect Free H Thick
6 3.2 0.3 .236 .126 .0118 .0059 .0177 .500
8 3.2 0.2 .315 .126 .0079 .0079 .0157 1.000
8 3.2 0.3 .315 .126 .0118 .0098 .0216 .833
8 3.2 0.4 .315 .126 .0157 .0079 .0236 .500
8 4.2 0.2 .315 .165 .0079 .0118 .0197 1.500
8 4.2 0.3 .315 .165 .0118 .0098 .0216 .833
8 4.2 0.4 .315 .165 .0157 .0079 .0236 .500
10 3.2 0.3 .394 .126 .0118 .0136 .0256 1.167
10 3.2 0.4 .394 .126 .0157 .0118 .0275 .750
10 3.2 0.5 .394 .126 .0197 .0098 .0295 .500
10 4.2 0.4 .394 .165 .0157 .0118 .0275 .750
10 4.2 0.5 .394 .165 .0197 .0098 .0295 .500
10 5.2 0.4 .394 .205 .0157 .0118 .0275 .750
10 5.2 0.5 .394 .205 .0197 .0098 .0295 .5008
12 4.2 0.4 .472 .165 .0157 .0157 .0314 1.000
12 4.2 0.5 .472 .165 .0197 .0138 .0335 .700
12 4.2 0.6 .472 .165 .0236 .0157 .0394 .670
12 5.2 0.5 .472 .205 .0197 .0157 .0354 .800
12 5.2 0.6 .472 .205 .0236 .0138 .0374 .583
12 6.2 0.5 .472 .244 .0197 .0138 .0335 .700
12 6.2 0.6 .472 .244 .0236 .0138 .0374 .583
12.5 5.2 0.5 .492 .205 .0197 .0138 .0340 .700
12.5 6.2 0.5 .492 .244 .0197 .0138 .0335 .700
12.5 6.2 0.7 .492 .244 .0275 .0118 .0394 .428
14 7.2 0.5 .551 .283 .0197 .0157 .0354 .800
14 7.2 0.8 .551 .283 .0315 .0118 .0433 .375
15 5.2 0.4 .591 .205 .0157 .0217 .0374 1.375
15 5.2 0.5 .591 .205 .0197 .0197 .0394 1.000
15 5.2 0.6 .591 .205 .0236 .0177 .0413 .750
15 5.2 0.7 .591 .205 .0276 .0157 .0433 .572
15 6.2 0.5 .591 .244 .0197 .0197 .0394 1.000
15 6.2 0.6 .591 .244 .0236 .0177 .0413 .750
15 6.2 0.7 .591 .244 .0276 .0157 .0433 .572
15 8.2 0.7 .591 .323 .0276 .0157 .0433 .572
15 8.2 0.8 .591 .323 .0315 .0157 .0472 .500
16 8.2 0.6 .630 .323 .0236 .0177 .0413 .750
16 8.2 0.7 .630 .323 .0276 .0177 .0453 .640
16 8.2 0.8 .630 .323 .0315 .0157 .0472 .500
16 8.2 0.9 .630 .323 .0354 .0138 .0492 .389
18 6.2 0.4 .709 .244 .0157 .0236 .0393 1.500
18 6.2 0.5 .709 .244 .0197 .0236 .0433 1.200
18 6.2 0.6 .709 .244 .0236 .0236 .0472 1.000
18 6.2 0.7 .709 .244 .0276 .0217 .0493 .785
18 6.2 0.8 .709 .244 .0315 .0197 .0512 .625
18 8.2 0.5 .709 .323 .0197 .0236 .0433 1.200
18 8.2 0.7 .709 .323 .0276 .0217 .0493 .785
18 8.2 0.8 .709 .323 .0315 .0197 .0512 .625
18 8.2 1.0 .709 .323 .0394 .0157 .0552 .400
18 9.2 0.7 .709 .362 .0276 .0197 .0472 .715
18 9.2 1.0 .709 .362 .0394 .0157 .0551 .400
20 8.2 0.6 .787 .323 .0236 .0276 .0512 1.166
20 8.2 0.7 .787 .323 .0276 .0256 .0532 .929
20 8.2 0.8 .787 .323 .0315 .0236 .0551 .750
mm Size Inch Size Inch Dimension Deflect /
O.D. I.D. Thick O.D. I.D. Thick Deflect Free H Thick
20 8.2 0.9 .787 .323 .0354 .0217 .0571 .611
20 8.2 1.0 .787 .323 .0394 .0216 .0610 .550
20 10.2 0.8 .787 .402 .0315 .0217 .0532 .690
20 10.2 0.9 .787 .402 .0354 .0217 .0571 .611
20 10.2 1.0 .787 .402 .0394 .0217 .0611 .550
20 10.2 1.1 .787 .402 .0433 .0177 .0610 .409
20 10.2 1.25 .787 .402 .0492 .0197 .0690 .400
20 10.2 1.5 .787 .402 .0591 .0118 .0708 .200
22.5 11.2 0.8 .886 .441 .0315 .0256 .0571 .813
22.5 11.2 1.25 .886 .441 .0492 .0197 .0689 .400
23 8.2 0.7 .906 .323 .0276 .0315 .0591 1.144
23 8.2 0.8 .906 .323 .0315 .0295 .0610 .938
23 8.2 0.9 .906 .323 .0354 .0276 .0630 .778
23 8.2 1.0 .906 .323 .0394 .0276 .0669 .700
23 10.2 0.9 .906 .402 .0354 .0295 .0649 .833
23 10.2 1.0 .906 .402 .0394 .0276 .0670 .700
23 10.2 1.25 .906 .402 .0492 .0256 .0748 .520
23 12.2 1.0 .906 .480 .0394 .0236 .0630 .600
23 12.2 1.25 .906 .480 .0492 .0236 .0728 .480
23 12.2 1.5 .906 .480 .0591 .0236 .0827 .400
25 10.2 1.0 .984 .402 .0394 .0295 .0689 .750
25 12.2 0.7 .984 .480 .0276 .0354 .0630 1.290
25 12.2 0.9 .984 .480 .0354 .0276 .0630 .778
25 12.2 1.0 .984 .480 .0394 .0315 .0709 .800
25 12.2 1.25 .984 .480 .0492 .0276 .0768 .560
25 12.2 1.5 .984 .480 .0591 .0217 .0808 .367
28 10.2 0.8 1.10 .402 .0315 .0374 .0689 1.187
28 10.2 1.0 1.10 .402 .0394 .0354 .0748 .900
28 10.2 1.25 1.10 .402 .0492 .0315 .0807 .640
28 10.2 1.5 1.10 .402 .0591 .0276 .0866 .470
28 12.2 1.0 1.10 .480 .0394 .0374 .0768 .950
28 12.2 1.25 1.10 .480 .0492 .0335 .0827 .680
28 12.2 1.5 1.10 .480 .0591 .0295 .0886 .500
28 14.2 0.8 1.10 .559 .0315 .0394 .0709 1.250
28 14.2 1.0 1.10 .559 .0394 .0315 .0709 .800
28 14.2 1.25 1.10 .559 .0492 .0335 .0827 .680
28 14.2 1.5 1.10 .559 .0591 .0256 .0847 .433
31.5 12.2 1.0 1.24 .480 .0394 .0434 .0827 1.100
31.5 12.2 1.25 1.24 .480 .0492 .0374 .0866 .760
31.5 12.2 1.5 1.24 .480 .0591 .0335 .0925 .570
31.5 16.3 0.8 1.24 .642 .0315 .0434 .0748 1.380
31.5 16.3 1.25 1.24 .642 .0492 .0354 .0846 .720
31.5 16.3 1.0 1.24 .642 .0591 .0354 .0945 .600
31.5 16.3 1.75 1.24 .642 .0690 .0276 .0966 .400
31.5 16.3 2.0 1.24 .642 .0787 .0296 .1083 .370
34 12.3 1.0 1.34 .484 .0394 .0492 .0886 1.250
34 12.3 1.25 1.34 .484 .0492 .0433 .0925 .880
34 12.3 1.5 1.34 .484 .0591 .0394 .0985 .667
34 14.3 1.25 1.34 .563 .0492 .0453 .0945 .920
34 14.3 1.5 1.34 .562 .0591 .0413 .1004 .700
34 16.3 1.5 1.34 .642 .0591 .0413 .1004 .700
34 16.3 2.0 1.34 .642 .0787 .0335 .1123 .425
35.5 18.3 0.9 1.40 .720 .0354 .0473 .0827 1.330
mm Size Inch Size Inch Dimension Deflect /
O.D. I.D. Thick O.D. I.D. Thick Deflect Free H Thick
35.5 18.3 1.25 1.40 .720 .0492 .0394 .0886 .800
35.5 18.3 2.0 1.40 .720 .0787 .0315 .1103 .400
40 14.3 1.25 1.57 .563 .0492 .0551 .1043 1.120
40 14.3 1.50 1.57 .563 .0591 .0492 .1083 .833
40 14.3 2.0 1.57 .563 .0787 .0413 .1200 .525
40 16.3 1.5 1.57 .642 .0591 .0512 .1103 .867
40 16.3 2.0 1.57 .642 .0787 .0433 .1220 .550
40 18.3 2.0 1.57 .720 .0787 .0453 .1240 .575
40 20.4 1.0 1.57 .803 .0394 .0512 .0950 1.300
40 20.4 1.5 1.57 .803 .0591 .0453 .1044 .767
40 20.4 2.0 1.57 .803 .0787 .0433 .1220 .550
40 20.4 2.25 1.57 .803 .0886 .0354 .1240 .400
40 20.4 2.5 1.57 .803 .0984 .0374 .1358 .380
45 22.4 1.25 1.77 .882 .0492 .0650 .1142 1.320
45 22.4 1.75 1.77 .882 .0689 .0512 .1201 .744
45 22.4 2.5 1.77 .882 .0984 .0394 .1378 .400
50 18.4 1.25 1.97 .724 .0492 .0630 .1122 1.280
50 18.4 1.5 1.97 .724 .0591 .0709 .1300 1.200
50 18.4 2.0 1.97 .724 .0787 .0591 .1378 .750
50 18.4 2.5 1.97 .724 .0984 .0630 .1615 .640
50 18.4 3.0 1.97 .724 .1181 .0551 .1731 .470
50 20.4 2.0 1.97 .803 .0787 .0591 .1378 .750
50 20.4 2.5 1.97 .803 .0984 .0531 .1515 .540
50 22.4 2.0 1.97 .882 .0787 .0630 .1417 .800
50 22.4 2.5 1.97 .882 .0984 .0551 .1535 .560
50 25.4 1.25 1.97 1.00 .0492 .0630 .1122 1.280
50 25.4 1.5 1.97 1.00 .0591 .0630 .1220 1.070
50 25.4 2.0 1.97 1.00 .0787 .0551 .1338 .700
50 25.4 2.5 1.97 1.00 .0984 .0551 .1535 .560
50 25.4 3.0 1.97 1.00 .1181 .0433 .1614 .367
56 28.5 1.5 2.20 1.122 .0591 .0787 .1378 1.330
56 28.5 2 2.20 1.122 .0787 .0630 .1417 .800
56 28.5 3 2.20 1.122 .1181 .0512 .1693 .433
60 20.5 2 2.36 .807 .0787 .0827 .1614 1.050
60 20.5 2.5 2.36 .807 .0984 .0709 .1693 .720
60 20.5 3 2.36 .807 .1181 .0670 .1850 .570
60 25.5 2.5 2.36 1.004 .0984 .0748 .1732 .760
60 25.5 3 2.36 1.004 .1181 .0651 .1832 .550
60 30.5 2.5 2.36 1.201 .0984 .0709 .1693 .720
60 30.5 3 2.36 1.201 .1181 .0669 .1850 .567
60 30.5 3.5 2.36 1.201 .1378 .0591 .1969 .428
63 31 1.8 2.48 1.22 .0709 .0945 .1654 1.330
63 31 2.5 2.48 1.22 .0984 .0689 .1673 .700
63 31 3 2.48 1.22 .1181 .0709 .1890 .600
63 31 3.5 2.48 1.22 .1378 .0551 .1929 .400
70 25.5 2 2.76 1.004 .0787 .0984 .1771 1.250
70 30.5 2.5 2.76 1.201 .0984 .0945 .1929 .960
70 30.5 3 2.76 1.201 .1181 .0827 .2008 .700
70 35.5 3 2.76 1.396 .1181 .0827 .2008 .700
70 35.5 4 2.76 1.398 .1575 .0709 .2279 .450
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 25
®
SCHNORR®DISC SPRINGS
Reduced Material Thicknesses on DiscSprings with Turned Contact Surfaces Springs with a thickness of 4 mm and over are machined all over
and are given lathe-turned contact surfaces at the inner and outer supporting edges. The contact surfaces have a width of about O.D./150. These contact surfaces cause an increase in spring load which has to be compensated by reducing the thickness T to T’. Call Customer Service for more information.
Note: Only when stacking spring layers in parallel does a reduced height have to be taken into consideration. The free height of the single disc remains unaltered. Special sizes up to 600 mm outside diameter can be manufactured if required.
mm Size Inch Size Inch Dimension Deflect /
O.D. I.D. Thick O.D. I.D. Thick Deflect Free H Thick
70 40.5 4 2.76 1.595 .1575 .0630 .2204 .400
70 40.5 5 2.76 1.595 .1968 .0472 .2441 .240
71 36 2 2.80 1.42 .0787 .1024 .1811 1.300
71 36 2.5 2.80 1.42 .0984 .0787 .1771 .800
71 36 4 2.90 1.42 .1575 .0630 .2205 .400
80 31 2.5 3.15 1.22 .0984 .1102 .2086 1.120
80 31 3 3.15 1.22 .1181 .0984 .2165 .833
80 31 4 3.15 1.22 .1575 .0827 .2402 .525
80 36 3 3.15 1.42 .1181 .1063 .2244 .900
80 36 4 3.15 1.42 .1575 .0866 .2441 .550
80 41 3 3.15 1.61 .1181 .0906 .2087 .767
80 41 4 3.15 1.61 .1575 .0866 .2441 .550
80 41 5 3.15 1.61 .1968 .0669 .2637 .340
90 46 2.5 3.54 1.81 .0984 .1261 .2245 1.280
90 46 3.5 3.54 1.81 .1378 .0984 .2362 .715
90 46 5 3.54 1.81 .1968 .0787 .2755 .400
100 41 4 3.94 1.61 .1575 .1260 .2835 .800
100 41 5 3.94 1.61 .1968 .1083 .3051 .550
100 51 2.7 3.94 2.01 .1063 .1418 .2481 1.330
100 51 3.5 3.94 2.01 .1378 .1102 .2480 .800
100 51 4 3.94 2.01 .1575 .1180 .2755 .750
100 51 5 3.94 2.01 .1966 .1102 .3070 .560
100 51 6 3.94 2.01 .2362 .0866 .3228 .367
112 57 3 4.41 2.24 .1181 .1458 .2640 1.230
112 57 4 4.41 2.24 .1575 .1260 .2835 .800
112 57 6 4.41 2.24 .2362 .0984 .3346 .417
125 41 4 4.92 1.61 .1575 .1654 .3229 1.050
125 51 4 4.92 2.01 .1575 .1772 .3347 1.125
125 51 5 4.92 2.01 .1968 .1535 .3503 .780
125 51 6 4.92 2.01 .2362 .1340 .3702 .567
125 61 5 4.92 2.40 .1968 .1575 .3535 .800
125 61 6 4.92 2.40 .2362 .1417 .3779 .600
125 61 8 4.92 2.40 .3150 .1142 .4292 .362
125 64 3.5 4.92 2.52 .1378 .1772 .3149 1.280
125 64 5 4.92 2.52 .1968 .1378 .3346 .700
125 64 8 4.92 2.52 .3150 .1024 .4174 .325
125 71 6 4.92 2.80 .2362 .1299 .3661 .550
125 71 8 4.92 2.80 .3150 .0945 .4094 .300
125 71 10 4.92 2.80 .3940 .0708 .4646 .180
140 72 3.8 5.51 2.83 .1496 .1968 .3465 1.310
140 72 5 5.51 2.83 .1968 .1575 .3543 .800
140 72 8 5.51 2.83 .3150 .1260 .4410 .400
150 61 5 5.91 2.40 .1968 .2087 .4055 1.060
150 61 6 5.91 2.40 .2362 .1890 .4252 .800
150 71 6 5.91 2.80 .2362 .1890 .4252 .800
150 71 8 5.91 2.80 .3150 .1575 .4724 .500
150 81 8 5.91 3.20 .3150 .1457 .4606 .460
150 81 10 5.91 3.20 .3940 .1181 .5118 .300
160 82 6 6.30 3.23 .236 .1772 .4134 .750
160 82 10 6.30 3.23 .394 .1378 .5318 .350
180 92 6 7.09 3.62 .236 .2008 .4360 .850
mm Size Inch Size Inch Dimension Deflect /
O.D. I.D. Thick O.D. I.D. Thick Deflect Free H Thick
180 92 10 7.09 3.62 .394 .1575 .5515 .400
200 82 8 7.87 3.23 .315 .2441 .5591 .775
200 82 10 7.87 3.23 .394 .2165 .6105 .550
200 82 12 7.87 3.23 .472 .1811 .6531 .383
200 92 10 7.87 3.62 .394 .2205 .6145 .560
200 92 12 7.87 3.62 .472 .1890 .6610 .400
200 92 14 7.87 3.62 .552 .1614 .7134 .293
200 102 8 7.87 4.02 .315 .2205 .5355 .700
200 102 10 7.87 4.02 .394 .2205 .6145 .560
200 102 12 7.87 4.02 .472 .1654 .6374 .350
200 102 14 7.87 4.02 .552 .1654 .7174 .300
200 112 12 7.87 4.41 .472 .1653 .6378 .350
200 112 14 7.87 4.41 .552 .1378 .6890 .250
200 112 16 7.87 4.41 .630 .1102 .7401 .180
225 112 8 8.86 4.41 .315 .2559 .5709 .813
225 112 12 8.86 4.41 .472 .1968 .6688 .417
250 102 10 9.84 4.02 .394 .3150 .7090 .800
250 102 12 9.84 4.02 .472 .2756 .7476 .583
250 127 10 9.84 5.00 .394 .2756 .6696 .700
250 127 12 9.84 5.00 .472 .2874 .7594 .608
250 127 14 9.84 5.00 .552 .2205 .7725 .400
250 127 16 9.84 5.00 .630 .2283 .8583 .362
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196426
®
ALLENAIR
CYLINDERS
VALVE-IN-HEAD CYLINDERS
• Small bore cylinders 1/2, 3/4, 1 1/8” bore up to 14” stroke
• Pneumatic and low pressure hydraulic 7/8 thru 4” bore up to 130” stroke
• All stainless steel cylinders in 300 series or all 316
• Single acting 1/2, 3/4, 1 1/8”, bores• Double acting 1 1/8” thru 4” bore• Stroke length up to 130”• Compact self-contained units
combining cylinder and valve into one complete module
• Faster response and flow
• 2 and 3 way valves 1/8 or 1/4” NPT Ports
• 4 way valves 1/8, 1/4, 3/8 & 1/2” NPT ports
• Single or double solenoid• AC and DC Voltages• 9 coil housing options including
explosion proof• Bleed pilot, single or double
pressure pilot
VALVES
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 27
®
ALLENAIR
ROTARY INDEX TABLES
CYL-CHECKS®• 3000 pounds max thrust load• Feed control available in forward,
rearward or both directions• Feed rate infinitely variable• Parallel or tandem mount• Optional stop or skip check features• For smooth, precise uniform
feed control
SPECIALS
• Four models available in clockwise or counter clockwise rotation
• 4 to 100 stations• 5 operating circuits• 5 top plate sizes• Accuracy with +/- .001”• Repeatability at a station is in the low tenths
• Allenair custom makes cylinders and valves in 5 to 7 working days for your specific applications.
For complete list of fluid power products for Allenair visit our website:
www.productodiemakers.com/allenair.html
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196428
®
RING PRECISION COMPONENTSENERPAC
PRECISION COMPONENTS• Custom Specials• OEM Components• Injection Mold
Components• Punches, Dies,
Guides & Quills
ENERPACEnerpac is the recognized global market leader in high pressure hydraulics. • Cylinders - Hydraulic cylinders are available in more than 1000 different configurations.
• Hydraulic Pumps - are available in more than 1000 different configurations. Featuring Hand, Battery, Electric, Air and Gasoline powered models
• Presses - Hydraulic Presses are available in a variety of capacities and sizes. All components can be ordered separately, making it easy to custom build the press which will exactly match your application requirements.
• Pullers - Complete line of pullers, whether your application requires mechanical, hydraulic or the patented Posi Lock system, Enerpac can satisfy your requirements.
• Valves - Hydraulic valves are available in a wide variety of models and configurations, rated for 10,000 psi operating pressure. Available for pump mounted operations or remote mounting and manual or solenoid actuation
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 29
®
TRANSFER PUNCHES & SCREWS
TRANSFER PUNCHESSET NO. 3-17
28 precision-made punches - 4-7/8” long with indexed stand. Sizes 3/32” to 1/2” by 1/64”. Plus handy 17/32” size. Finest tool steel, carefully heat treated.
SET NO. 25 Metric size transfer punch set No. 25 is for the machine shop tooling up for metric. Set of 25 precision punches in the most popular metric sizes 1.0 MM through 13.0 by .5 MM
SET NO. A-Z This 26-piece punch set features letter sizes A through Z. All punches precision crafted of the finest tool steel. Heat treated and tempered for years of machine shop service. Punches are 4-7/8” long with rugged index stand.
Fractional Sizes: (dia. inches) Ranges from 1/16” through 1” by 64ths and 1-1/32” through 2” by 16ths
Letter Sizes: Ranges from A through Z Wire Gauge Sizes: Ranges from A through Z Metric Sizes: Ranges from 1.0 mm through
26.0 mm by 0.5 mm.
TRANSFER SCREWS & SETS• Screws-only are sold in any quantity over 6 per size.
• Sets consist of 6 screws of one size contained in a holder, which doubles as a wrench.
Standard Sizes:COURSE
Standard Sizes:FINE
4-40 4-48
5-40 5-44
6-32 6-40
8-32 8-36
10-24 10-32
3/16-24 3/16-32
12-24 12-28
1/4-20 1/4-28
5/16-18 5/16-24
3/8-16 3/8-24
7/16-14 7/16-20
1/2-13 1/2-20
9/16-12 9/16-18
5/8-11 5/8-18
3/4-10 3/4-16
7/8-9 7/8-14
1-8 1-14
METRIC Sizes:
M-3 X 0.50
M-4 X 0.70
M-5 X 0.80
M-6 X 1.00
M-8 X 1.25
M-10 X 1.50
M-12 X 1.75
M-14 X 2.00
M-16 X 2.00
M-20 X 2.50
M-24 X 3.00
SET NO. 33 A ‘super’ 33-piece set, sizes 1/2” through 1” by 64ths. This larger, complete set provides a total matched set of transfer punches that satisfies most shop requirements. Heat treated and tempered.
SET NO. 1-60 60 piece wire gauge transfer punch set, sizes 1 through 60. This precision, matched set gives your shop a complete set of wire gauge sizes, packed in a handy index stand. Punches are 4-7/8” long.
SET NO. 25A METRIC Sizes 13 MM through 25 MM by .5 MM Heat treated and tempered for years of service. Packaged in a rugged index stand.
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196430
®
STANDARD SPRING PLUNGERS
NYLOKA (CLASS 2ATHREADS)
C
D
B
When ordering with Nylock, add “N” at the end of the part number for sizes 1/4-20 and larger; under 1/4-20, add “P” at end of part number.
When ordering with Nylok, add “N” at the end of the part number for sizes 1/4-20 and larger; under 1/4-20, add “P” at end of part number.
HOW TO CHOOSE THE MODEL TO MEET YOUR APPLICATION1. Select end forces needed - standard or light (Silvernose). 2. Select plunger travel distance required. 3. Select plunger type - hex or round. 4. Select plunger material - steel, stainless steel, phenolic or Delrin®. 5. Select thread size.
Delrin® is a trademark of DuPont Corp.
Spring forces are accurate, uniform and dependable. Large bearing surface on plunger prevents binding, assures perfect alignment of the plunger at any extension. Steel bodies have a black oxide finish and case hardened nose.
Zinc plated plunger noses identify Silvernose spring plungers as having light end forces. Special springs were developed for fast, repetitive operations…designed to flex thousands of times. Steel bodies have a black oxide finish and case hardened nose.
STANDARD SPRING PLUNGERS
ROUND NOSE
PART NO. END FORCE, LBS.A B C D USE
WRENCHSTEEL BODY STEEL NOSE
STAINLESS BODY STAINLESS NOSE
INIT. FINAL
S-48 SSS-48 1.5 4.5 6-32 17/32” 1/16” .044-.045 VW-48
S-48A SSS-48A 1.0 1.6 6-32 3/8” 1/16” .044-.045 VW-48
S-50 SSS-50 2.7 7.3 8-32 5/8” 3/32” .069-.070 VW-50
S-52 SSS-52 2.9 11.1 10-32 3/4” 1/8” .091-.092 VW-52
S-54 SSS-54 3.0 13.0 1/4-20 1” 3/16” .117-.118 VW-54
S-54A SSS-54A 3.0 13.0 1/4-28 1” 3/16” .117-.118 VW-54
S-54B SSS-54B 2.0 9.0 1/4-20 3/4” 1/8” .117-.118 VW-54
S-56 SSS-56 3.0 15.0 5/16-18 1” 3/16” .133-.135 VW-56
S-58 SSS-58 5.5 14.5 3/8-16 1-1/8” 3/16” .186-.187 VW-58
S-60 SSS-60 6.6 17.4 1/2-13 1-1/4” 1/4” .247-.248 VW-60
S-62 SSS-62 10.5 25.5 5/8-11 1-1/2” 5/16” .308-.310 VW-62
S-64 SSS-64 6.7 37.3 3/4-10 1-3/4” 5/16” .373-.374 VW-64
S-66 SSS-66 16.0 68.0 1-8 2-13/32” 1/2” .496-.498 VW-66
HEAVY END FORCES
ROUND SILVERNOSE®
PART NO. END FORCE, LBS.A B C D USE
WRENCHSTEEL BODY STEEL NOSE
STAINLESS BODY STAINLESS NOSE
INIT. FINAL
S-49 SSS-49 0.5 1.5 6-32 17/32” 1/16” .044-.045 VW-48
S-51 SSS-51 0.7 2.3 8-32 5/8” 3/32” .069-.070 VW-50
S-53 SSS-53 1.3 2.7 10-32 3/4” 1/8” .091-.192 VW-52
S-55 SSS-55 1.0 4.0 1/4-20 1” 3/16” .117-.118 VW-54
S-55A SSS-55A 1.0 4.0 1/4-28 1” 3/16” .117-.118 VW-54
S-57 SSS-57 1.5 4.5 5/16-18 1” 3/16” .134-.135 VW-56
S-59 SSS-59 2.8 7.2 3/8-16 1-1/8” 3/16” .186-.187 VW-58
S-61 SSS-61 2.7 9.3 1/2-13 1-1/4” 1/4” .247-.248 VW-60
S-63 SSS-63 3.5 10.5 5/8-11 1-1/2” 5/16” .308-.310 VW-62
S-67 SSS-67 4.0 31.0 1-8 2-13/32” 1/2” .496-.498 VW-66
LIGHT END FORCES
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 31
®
STUBBY SPRING PLUNGERS
NYLOK
A (CLASS 2A THREADS)
CB
D
Stubby” spring plungers offer the advantages of a ball plunger’s short body with the long nose of a spring plunger. These compact units provide considerable plunger travel and high end forces in applications where space is restricted - their bodies are only half the length of spring plunger, yet plunger travel is twice that of a ball plunger.
Case hardened nose - Offers excellent wear resistance; however, core is ductile to reduce possibility of fracturing under impact. Steel version only.
Available with steel, stainless steel or Delrin noses. Steel bodies have a black oxide finish.
Nose telescopes completely - Permits use where mating surfaces must be flush.
Quickly installs from either end - Only tool required is a wrench.
Complete Viler product line available - Call for your free catalog
When ordering with Nylok, add “N” at the end of the part number for sizes 1/4-20 and larger; under 1/4-20, add “P” at the end of the part number.
STUBBY SPRING PLUNGERS
For positive holding action, spring plungers offer many advantages. Quickly, easily installed or removed. Apply accurately controlled end pressures. 418 types and sizes including round nose, hex nose for easy removal, stubby for tight places, hand retractable and ball type for use where side loads are a problem. Can be modified to fit your special needs. Steel or stainless. Other materials on special order.
HOLD IT!
WITH VLIER SPRING LOADED DEVICES
PART NO. END FORCE, LBS.A B C D USE
WRENCHSTEEL BODY STEEL NOSE
STAINLESS BODY DELRIN NOSE
STAINLESS BODYSTANLESS STEEL NOSE
INIT. FINAL
M-50A NM-50A SSM-50A 1.5 4.75 8-32 .437 .052 .070 VW-50
M-50 NM-50 SSM-50 1.5 4.75 8-36 .437 .052 .070 VW-50
M-52 NM-52 SSM-52 1.75 6.25 10-32 .468 .065 .093 VW-52
M-54 NM-54 SSM-54 3.0 10.5 1/4-20 .531 .078 .119 VW-54
M-56 NM-56 SSM-56 3.75 15.5 5/16-18 .562 .084 .135 VW-56
M-58 NM-58 SSM-58 4.5 18.5 3/8-16 .625 .110 .186 VW-58
M-60 NM-60 SSM-60 5.0 28.0 1/2-13 .750 .151 .248 VW-60
M-62 NM-62 SSM-62 7.0 50.0 5/8-11 1.062 .215 .310 VW-62
HEAVY END FORCES
When ordering with Nylok, add “N” at the end of the part number for sizes 1/4-20 and larger; under 1/4-20, add “P” at the end of the part number.
PART NO. END FORCE, LBS.A B C D USE
WRENCHSTEEL BODY STEEL NOSE
STAINLESS BODY DELRIN NOSE
STAINLESS BODYSTANLESS STEEL NOSE
INIT. FINAL
M-51A NM-51A SSM-51A 0.5 1.5 8-32 .437 .052 .070 VW-50
M-51 NM-51 SSM-51 0.5 1.5 8-36 .437 .052 .070 VW-50
M-53 NM-53 SSM-53 0.75 2.5 10-32 .468 .065 .093 VW-52
M-55 NM-55 SSM-55 1.0 3.5 1/4-20 .531 .078 .119 VW-54
M-57 NM-57 SSM-57 1.25 4.0 5/16-18 .562 .084 .135 VW-56
M-59 NM-59 SSM-59 1.5 5.0 3/8-16 .625 .110 .186 VW-58
M-61 NM-61 SSM-61 1.75 5.5 1/2-13 .750 .151 .248 VW-60
M-63 NM-63 SSM-63 2.0 8.5 5/8-11 1.062 .215 .310 VW-62
LIGHT END FORCES
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196432
®
VIBRASYSTEMS INC.
TYPE: VSCM, CMSS, CRS, CSS Cup Mount• Ideally suited for presses, pumps, blowers, crushers or injection molding machines• Designed for where shear loads are up to 40% of the maximum
load. • Available in stainless steel.
TYPE: SML, VTM Compression Shear Mounts• Designed for heavy machinery such as presses, rolling mills,
injection molding machines• Provide good stability with shear loads of up to 40% of the
maximum load while vertical deflection is low.
TYPE: NVS Compress Shear Mounts• Recommended for applications with both compression and
shear loads. • Can be used for the installation of almost all factory production
equipment.• Leveling adjustment – 1/2” (12mm).
TYPE VM, VMT Compression Shear Leveling Mounts• Designed for installation where shear loads are not more than
10% of the maximum load.• Self-aligning capabilities compensate for uneven floors.
TYPE: VMH Leveling Wedge Mounts• Designed for precision leveling of heavy industrial equipment• Special opening allows bolting machines to the floor when
leveling is done.
CYLINDRICAL MOUNTS – BOBBINS• Designed for wide range of applications with light loads where
simple and compact anti-vibration mounting are required, such as: fans, motors, scales, electrical panels, compressors, air conditioners, computer equipment, etc.
TYPE: VP, ECRMP, RP, CRMP, SRMP, VB Neoprene Pads• Standard pads are 18” x 18” overall dimensions• Thickness available from 1/4” and up to 1”• Different hardness for different load capacities
INDUSTRIAL RUBBER PRODUCTS IN ROLLS• Red silicone, Neoprene, Pure Gum (natural rubber), EPDM,
Hypalon, Viton, Butyl, Nitrile, SBR, Rubber Matting, etc.• Available in thickness for up to 2” (50mm)
VIbRASYSTEMS INC.
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 33
®
URETHANE PRODUCTS
Standard Lengths are:
Hardness: Colors:
12”, 24”, 36” 20A, 30A, 40A, 60A, 75A, 80A, 90A, 95A, 75D
Amber, Black, (Other Colors Available)
Standard sizes are: Hardnesses: Colors:
12"W x 12" L, 12"x 24" L24" x 24" L, 12" x 48" L24" x 48" L
20A, 30A, 40A60A, 70A, 80A90A, 95A, 75D
Amber, Black,(Other Colors Available)
Standard Lengths are: Width x Height (in): Hardness: Colors:
12", 24”,36", 48" ½ x ½, ¾ x ¾, 1 x 1, 1 ¼ x 1 ¼, 1 ½ x 1 ½, 2 x 2, 2 x 3, 3 x 3, 4 x 4, 4 x 5
20A, 30A, 40A, 60A, 70A, 80A, 90A, 95A, 75D
Amber, Black, (Other Colors Available)
O.D.(inch) ID (inch)
1 ¾ 1
2 ½ , 1, 1 ¼, 1 ½
2 ½ ½, 1, 1 ¼, 1 ½
2 ¾ 1 ¼, 1 ½, 1 ¾, 2, 2 ½
3 1, 1 ½, 2, 2 ¼
3 ¼ 1 ¾, 2 ¼
3 ½ 1 ¼, 2, 2 ½, 2 ¾
O.D.(inch) ID (inch)
3 ¾ 2 ¾
4 2, 2 ¼, 2 ½
4 ½ 2 ½, 3
5 3
5 ½ 4
6 5
Standard Lengths are: Diameters (in): Hardnesses: Colors:
6",12”, 24", 36", 48" ¼, 3⁄8, ½, 5⁄8, ¾, 7⁄8, 1, 1 1⁄8, 1 ¼, 1 3⁄8, 1 ½, 1 5⁄8, 1 ¾, 2, 2 ¼, 2 ½, 3, 3 ½, 4, 5
20A, 30A, 40A,60A, 70A, 80A, 90A, 95A, 75D,
Amber, Black,(Other Colors Available)
Model Number: PH-12 PH-20 PH-24 PH-48 PH-60 PH-88
Face Model F12-* F20-* F24-* F48-* F60-* F88-*
Head Length (with faces) 3.3” 3.8 4.0” 5.0 6.0” 7.7”
Face Dia. 1.4” 1.8” 1.9” 2.5” 2.9” 2.9”
OAL Hammer length 10” 11” 11.75” 12.75” 14.75” 19.25”
Approx. Weight 0.75 lbs 1.5 lbs 2 lbs 3 lbs 4.5 lbs 7 lbs
Producto Urethane Strippers and Urethane Closed End Strippers are also available.
URETHANE SHEETS• Tolerances for width & length for all sheets:
+1/8” to + 1” depending on the sheet size.
RODS (Round Sections)Used as strippers, pressure cylinders in bulging applications as
tube bending mandrels & for machining variety of parts
BARS (Square & Rectangular Sections)Molded to shape. Used as Die-Pads in bending applications, as pressure Pads in
stamping applications, and as bumper strips.
TUBES (Hollow Sections)We have a huge inventory of tube molds that are interchangeable for standard fractional sizes of I.D.s & O.D.s• Tolerance: I.D : + 0.010” , - 0.060” ; O.D : + 0.060” , - 0.010
POLY-HAMMERS (Hollow Sections)• Molded Polyurethane head is shot-filled, with screw-in faces. • When the hammer faces are worn out, just unscrew the face and screw-in a new face.• Hammer handles are steel reinforced, molded integral with the head, with a protruding texture on the handle for a better grip.• Standard hammers are ORANGE color. Hammer faces are available in 6 color-coded hardness of Urethane as mentioned below:
* Hammer faces Available Hardness: 60A - Clear (Soft), 70A – Blue, 80A – Green, 90A – Red, 95A – Amber, and 75D - Black ( Hard).
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 196434
®
DACWEICON
DACDAC Industries mold release products, cleaners, degreasers, lubricants and rust inhibitors are designed to
extend machine and tool life, improve mold release properties, and increase efficiency.
Product No. Product Quantity
DAC-101 Moisture Guard 12 cans/Case
DAC-102 On Line Resin Remover 12 cans/Case
DAC-103 Universal All Purpose Degreaser 12 cans/Case
DAC-104 All Purpose Foam 12 cans/Case
DAC-105 Dry Film With Coverage Indicator 12 cans/Case
DAC-107 703 All Purpose Spray 12 cans/Case
DAC-107-A Trigger Sprayer EACH
DAC-108 Does It All 12 cans/Case
DAC-110 Micro Plate 12 cans/Case
DAC-111 Extreme Resin Remover 12 cans/Case
DAC-112 Armor Plate 12 cans/Case
DAC-113 Super Lube 12 cans/Case
DAC-115 Rhino Plate 12 cans/Case
DAC-119 Hopper & Grinder with Acid Static 12 cans/Case
DAC-200 Die Lube 12 cans/Case
DAC-205 Excel 12 cans/Case
DAC-206 Wear Guard 12 cans/Case
DAC-208 On Cycle Heavy Duty Resin Remover 12 cans/Case
DAC-220 DAC's Easy Spray Grease 12 cans/Case
DAC-300 Ultra Fine Dry Mold Shield 12 cans/Case
DAC-353 Universal All Purpose Degreaser II 12 cans/Case
Product No. Product Quantity
DAC-354 Total Mold Cleaner & Degreaser 12 cans/Case
DAC-405 Contact & Circuit Board Cleaner 12 cans/Case
DAC-15151 All Purpose Mold Release 12 cans/Case
DAC-30612 Heavy Duty Paintable Mold Release 12 cans/Case
DAC-36361 Paintable Mold Release 12 cans/Case
DAC-40512 Heavy Duty Silicone Mold Release 12 cans/Case
DAC-45451 All Temperature Silicone Mold Release 12 cans/Case
DAC-55512 Lecithin Drilling & Tapping Fluid 12 cans/Case
DAC-75751 Penetrating Oil 12 cans/Case
DAC-85851 Biodegradable Paintable Mold Release 12 cans/Case
WEICONSolutions for production, repair, maintenance & servicing.
Surface and corrosion protection
Aluminum Sprays
Brass Spray
Chrome Silver Spray
Copper Spray
Corro-Protection
Rust Protection 2000 Plus
Stainless Steel Spray
Zinc Sprays
Zinc Alu Spray
Cleaning and degreasing
Brake Cleaner
Burner Cleaner
Cleaner Spray S
Compressed-Air Spray
Electro Contact Cleaner
Mould Cleaner
Multi Foam
Plastic Cleaner
Multi Foam
Plastic Cleaner
Sealant & Adhesive Remover
Surface Cleaner
TFT/LCD Screen-Cleaner
Visor Cleaner
Lubrication
Lubricating and multifunctional oils
Adhesive lubricants
Assembly sprays
Dissolving and separating
Alu Grinding Protection
Chewing Gum Remover
Label Remover
Mould Release Agent
Rust Loosened & Contact Spray
Rust-Shock
Welding Protection Spray
Care and protection
Cockpit Spray
Contact Spray
Hand Protective Foam
Metal-Fluid
Stainless Steel Care Spray
Inspection aids and agents
Starter Spray
Adhesive Spray
Freeze Spray
Leak Detection Spray
WEICON Repair SticksThe uncomplicated solution for all repair and maintenance work. • Easy to use: Cut off - knead – use• Always the right portion, even for small repairs• Bonds to metal, hard-plastics*, fibre-reinforced
materials, wood, glass, ceramic and stone• Nine different Repair Sticks to choose from for various
applications.• All Around Lubricants• Two Component Adhesives• One Component Adhesives• Elastic AdhesivesComplete WEICON
line available.
WWW.PRODUCTODIEMAKERS.COM • SERVING THE CANADIAN MANUFACTURING INDUSTRY SINCE 1964 35
®
PRODUCTO DIEMAKERSLOCATIONS, DIVISIONS, AFFLIATES & PARTNERS
PRODUCTO DIEMAKERS SUPPLIES LOCATIONS
ONTARIOProducto Diemakers
641 Chrislea Rd, Unit #4 Vaughan, ON L4L 8A3 Phone: 905-856-9990 Toll Free: 866-562-0555 Fax: 905-856-9887
www.productodiemakers.com [email protected]
QUEBECProducto Diemakers
4486 Boulevard de la Grande Allee Boisbriand, QC J7H 1R9 Phone: 450-430-5082 Toll Free: 866-508-5082 Fax: 450-430-1022
www.productodiemakers.com [email protected]
Grinding Systems & Machinery Systems
800 Union Ave Bridgeport, CT 06607 Phone: 203-366-3224 Fax: 203-367-0418 www.mooretool.com
Nanotechnology Systems, LLC
230 Old Homestead Hwy Swanzey, NH 03446 Phone: 603-352-3030 Fax: 603-352-3363 www.nanotechsys.com
DIVISIONS: AFFILIATES:
Springs, Accessories & Die Sets 5835 Harper Rd Solon, OH 44139 Phone: 440-542-0000 Toll Free: 800-237-1440 Fax: 440-542-0250 www.dieco.us Serving the U.S.
is a proud distributor of these quality products:
Ajax • Allenair • All American • Asco
Associated Spring Raymond • Barry Controls • DAC
Enerpac • Kaller • Knu-Vise (Lapeer) • Lee Springs
Ortman • Polyurethane Products • Royal • Schmalz
Schnorr • Stilson • VibraSystems • Vlier • Weicon
Precision Components 2980 Turner Rd Jamestown, NY 14701 Phone: 716-484-7131 Toll Free: 800-828-2216 Fax: 716-484-2235 www.ringprecision.com
®
PRODUCT LINE
Vlier Spring Loaded Stubby Ball And Push-Fit Plungers, Ball Buttons, Torque Thumb Screws & Handles, Retractable Plungers, Tooling Flanges, Spring Stops, Toggle Pads.
Kaller Gas Springs, Flex Cam, Controllable Gas Springs, Roller Cam, Flange Stripper, Pierce-Nut Stamping Equipment.
EnerpacCylinders, Hydraulic Pumps, Hydraulic Presses, Pullers and Hydraulic Valves.
NEW!
SchnorrPrecision Disc Springs, Safety Washers, 6mm - 250mm OD. High alloyed steels. Slotted and non-slotted k-springs for preloading ball bearings. Sizes from 1/4” to 10” O.D.
Transfer Screws & Sets Screws are available in sets of six per size. Consist of six screws contained in a holder which doubles as a wrench. Can be purchasedindividually. Metric Transfer Punch Size also available.
ISO D-Line Die Springs, meet ISO 10243 specifications.
CUSTOM/SPECIAL Springs available per your specifications.
Die Springs In addition to our standard Die Springs, we offer separate lines manufactured to ISO & JIS specifications. Full line of Stainless Steel Mechanical Spring Struts.
Allenair Air and Light Hydraulic Cylinders to 4” bore, Valve-In-Head, 100% Stainless Steel Cylinders, Air Clamps, 2, 3, & 4- Way Valves, Cyl-Checks, Rotary Index Tables, Custom and Specials.
DACDegreasers, Resin Remover, Rust Inhibitors, Lubricants, Greases, Specialty Lubricant, Drilling & Tapping, Mold Releases, Heavy Duty Mold Releases and Plating Agents.
Urethane• Available in sheets, rods,
bars and tubes.
• Poly-Hammers available in 6 sizes.
Weicon • All Around Lubricants• Two Component Adhesives• One Component Adhesives• Elastic Adhesives• Technical Sprays
www.productodiemakers.com [email protected]
ONTARIO • TEL: (905) 856-9990 FAX: (905) 856-9887 TOLL FREE: 1-866-562-0555 641 Chrislea Road, Unit #4, Vaughan, ON L4L 8A3
QUEBEC • TEL: (450) 430-5082 FAX: (450) 430-1022 TOLL FREE: 1-866-508-5082 4486 Boulevard de la Grande Allee, Boisbriand, QC J7H 1R9