Process application guide for vehicle INDASA provides on a ... · Block sand the primed area. 4...
1
Process application guide for vehicle repair, refinish preparation and polishing INDASA provides on a daily basis: • High performance abrasive systems and innovative refinishing solutions • Consistency through a repair process • Commercial advantage through best working practice • Structured programme for enhanced bodyshop profitability Health and safety compliance is required for all processes. The Indasa Academy represents the commitment and delivery of technical expertise and instruction. Training programmes are tailored to develop the customer’s skill base and optimise performance efficiencies in the workplace. Preparation for primer 1 Prepare the repair and surrounding area for primer application. METHOD Machine sand the repair area to a feather edge. PRODUCT Rhynogrip HT Line Ultravent disc. Grit P320. EQUIPMENT Orbital palm sander with 5mm orbit. Softform adaptor pad. Dust extraction. Preparation for primer 4 Protection masking for the panel and repair area. METHOD Apply masking tape to the edge of the repair area to protect any adjacent panels. PRODUCT MTE-RED masking tape 24/36mm. Masking film/paper. Preparation for primer 2 Clean the repair and surrounding area. METHOD Remove all dust and dirt from panel leaving a clean/dry repair area. PRODUCT Panel wipe cloth. Degreaser. Preparation for primer 5 Thoroughly clean the repair area prior to primer application. METHOD Remove all dust/dirt particles from repair area leaving a clean/dry panel surface for priming. PRODUCT Low tack cloth. Preparation for primer 3 Apply 440 Express to eliminate micro-pinholes in the repair surface and to enhance primer coverage. METHOD Apply a small amount with a cloth to cover the repair area. Wipe off residue and leave to dry for 15 minutes prior to primer application. PRODUCT Evercoat 440 Express. Preparation for primer 6 Apply primer surfacer to the repair. METHOD Refer to the paint manufacturer’s technical data sheet for application process. PRODUCT Compliant paint refinish process. Preparation for topcoat 1 Block sand the primed area. Preparation for topcoat 4 Thoroughly inspect and clean the panel repair area prior to topcoat application. METHOD Remove all dust/dirt particles from repair area leaving a clean/dry panel surface for painting. PRODUCT Degrease with panel wipe cloth. Low tack cloth. Preparation for topcoat 2 Reapply Dry Guide Coat and machine sand the primed area. METHOD Machine sand the primed area to a smooth finish. PRODUCT Rhynogrip HT Line Ultravent disc. Grit P500. EQUIPMENT Orbital palm sander with 5mm orbit. Softform adaptor pad. Dust extraction. Preparation for topcoat 5 Apply the topcoat. METHOD Refer to the paint manufacturer’s technical data sheet for application process. PRODUCT Compliant paint refinish process. Preparation for topcoat 3 Prepare the surrounding blend area. METHOD Machine sand the area to be blended for clear coat. Hand sand any edges and awkward areas. PRODUCT Rhynogrip HT Line Ultravent disc. Grit P1000. Nylon web (grey) or Sponge (MF). EQUIPMENT Orbital palm sander with 5mm orbit. Softform adaptor pad. Dust extraction. Paint rectification and polish 1 Remove any paint imperfections (nibs) from the paint surface. METHOD For small areas denib by hand. Machine sand large areas. PRODUCT Rhynowet paper P2000 Rhynogrip Filmline disc. Grit P1500 (size to suit). EQUIPMENT Orbital palm sander with 5mm orbit. Softform adaptor pad. Dust extraction. Paint rectification and polish 4 Polish the panel to a showroom gloss finish. METHOD Low speed polisher with liquid polish to remove swirl marks and to produce high gloss finish. PRODUCT Autogloss Hi-Gloss Plus. EQUIPMENT E-Series electric orbital polisher. Autogloss Mop (black). Paint rectification and polish 2 Prepare the surface area for compounding. METHOD Machine sand the area to remove all traces of sanding marks in the surface. PRODUCT Rhynocell disc. Grit MF3000 (size to suit). EQUIPMENT Orbital palm sander with 5mm orbit. Dust extraction. Paint rectification and polish 5 Remove all residue and hand polish to a flawless finish. METHOD Hand polish the surface to a high gloss finish. PRODUCT Microfibre cloth (blue). Paint rectification and polish 3 Machine compound the repair area. METHOD Low speed polisher with compound to remove all traces of sanding marks and to leave gloss finish. PRODUCT Autogloss Compound Plus. EQUIPMENT E-Series electric rotary polisher. Autogloss Mop (white). Panel repair 1 Clean panel prior to repair. METHOD Remove all dust, dirt and traffic film residue from panel leaving a clean/dry repair area. PRODUCT Panel wipe cloth. Degreaser. Panel repair 4 Shape the filler to match the required panel contour. METHOD Apply Dry Guide Coat to the filler area then hand sand with dust extraction block to achieve the required shape of repair. PRODUCT Rhynogrip HT Line strip. Grit P80 – P180 (size to suit). Dry Guide Coat. EQUIPMENT Dust extraction block. Dust extraction. Panel repair 2 Sand the repair area to prepare for the application of body filler. METHOD Machine sand the repair area to a clean, bare metal surface or prepare the OE paint finish if using multi-substrate body filler. PRODUCT Rhynogrip HT Line Ultravent disc. Grit P80 – P180. EQUIPMENT Orbital palm sander with 5mm orbit. Dust extraction. Panel repair 5 Remove sanding scratches in the filler. METHOD Hand sand the bodyfiller with dust extraction block to a smooth surface finish. PRODUCT Rhynogrip HT Line strip. Grit P180 (size to suit). EQUIPMENT Dust extraction block. Dust extraction. Panel repair 3 Prepare the Evercoat™ body filler and apply to the repair area. METHOD Mix the hardener with the filler to a 2% ratio (by weight) on the mixing board. PRODUCT Evercoat Rage Ultra. EQUIPMENT Rhyno mixing board. Autofill spreader. Panel repair 6 Machine sand the repair area to produce a feather edge. METHOD Machine sand the repair area to remove all scratches, leaving a feather edge into the surrounding paintwork. PRODUCT Rhynogrip HT Line Ultravent disc. Grit P180 – P320 (feather edge). EQUIPMENT Orbital palm sander with 5mm orbit. Dust extraction. METHOD Apply Dry Guide Coat then hand sand the repair area, leaving a smooth, primed surface finish. PRODUCT Rhynogrip HT Line strip Grit P320 (size to suit). For awkward areas use Rhynosoft P600 or Sponge SF. Dry Guide Coat. EQUIPMENT Dust extraction block. Dust extraction.
Transcript of Process application guide for vehicle INDASA provides on a ... · Block sand the primed area. 4...
Process application guide for vehicle repair, refinish preparation and polishing
INDASA provides on a daily basis:• High performance abrasive systems and innovative refinishing solutions
• Consistency through a repair process
• Commercial advantage through best working practice
• Structured programme for enhanced bodyshop profitability
Health and safety compliance is required for all processes.
The Indasa Academy represents the commitment and delivery of technical expertise and instruction.
Training programmes are tailored to develop the customer’s skill base and optimise performance efficiencies in the workplace.
Preparation for primer1Prepare the repair and surrounding area for primer application.
METHODMachine sand the repair area to a feather edge.
PRODUCTRhynogrip HT Line Ultravent disc. Grit P320.
EQUIPMENTOrbital palm sander with 5mm orbit.Softform adaptor pad. Dust extraction.
Preparation for primer4Protection masking for the panel and repair area.
METHODApply masking tape to the edge of the repair area to protect any adjacent panels.
PRODUCTMTE-RED masking tape 24/36mm.Masking film/paper.
Preparation for primer2Clean the repair and surrounding area.
METHODRemove all dust and dirt from panel leaving a clean/dry repair area.
PRODUCTPanel wipe cloth.Degreaser.
Preparation for primer5Thoroughly clean the repair area prior to primer application.
METHODRemove all dust/dirt particles from repair area leaving a clean/dry panel surface for priming.
PRODUCTLow tack cloth.
Preparation for primer3Apply 440 Express to eliminate micro-pinholes in the repair surface and to enhance primer coverage.
METHODApply a small amount with a cloth to cover the repair area. Wipe off residue and leave to dry for 15 minutes prior to primer application.
PRODUCTEvercoat 440 Express.
Preparation for primer6Apply primer surfacer to the repair.
METHODRefer to the paint manufacturer’s technical data sheet for application process.
PRODUCTCompliant paint refinish process.
Preparation for topcoat1Block sand the primed area.
Preparation for topcoat4Thoroughly inspect and clean the panel repair area prior to topcoat application.
METHODRemove all dust/dirt particles from repair area leaving a clean/dry panel surface for painting.
PRODUCTDegrease with panel wipe cloth.Low tack cloth.
Preparation for topcoat2Reapply Dry Guide Coat and machine sand the primed area.
METHODMachine sand the primed area to a smooth finish.
PRODUCTRhynogrip HT Line Ultravent disc.Grit P500.
EQUIPMENTOrbital palm sander with 5mm orbit.Softform adaptor pad.Dust extraction.
Preparation for topcoat5Apply the topcoat.
METHODRefer to the paint manufacturer’s technical data sheet for application process.
PRODUCTCompliant paint refinish process.
Preparation for topcoat3Prepare the surrounding blend area.
METHODMachine sand the area to be blended for clear coat.Hand sand any edges and awkward areas.
PRODUCTRhynogrip HT Line Ultravent disc. Grit P1000.Nylon web (grey) or Sponge (MF).
EQUIPMENTOrbital palm sander with 5mm orbit. Softform adaptor pad.Dust extraction.
Paint rectification and polish1Remove any paint imperfections (nibs) from the paint surface.
METHODFor small areas denib by hand.Machine sand large areas.
PRODUCTRhynowet paper P2000 Rhynogrip Filmline disc. Grit P1500 (size to suit).
EQUIPMENTOrbital palm sander with 5mm orbit.Softform adaptor pad.Dust extraction.
Paint rectification and polish4Polish the panel to a showroom gloss finish.
METHODLow speed polisher with liquid polish to remove swirl marks and to produce high gloss finish.
PRODUCTAutogloss Hi-Gloss Plus.
EQUIPMENTE-Series electric orbital polisher.Autogloss Mop (black).
Paint rectification and polish2Prepare the surface area for compounding.
METHODMachine sand the area to remove all traces of sanding marks in the surface.
PRODUCTRhynocell disc.Grit MF3000 (size to suit).
EQUIPMENTOrbital palm sander with 5mm orbit.Dust extraction.
Paint rectification and polish5Remove all residue and hand polish to a flawless finish.
METHODHand polish the surface to a high gloss finish.
PRODUCTMicrofibre cloth (blue).
Paint rectification and polish3Machine compound the repair area.
METHODLow speed polisher with compound to remove all traces of sanding marks and to leave gloss finish.
PRODUCTAutogloss Compound Plus.
EQUIPMENTE-Series electric rotary polisher.Autogloss Mop (white).
Panel repair1Clean panel prior to repair.
METHODRemove all dust, dirt and traffic film residue from panel leaving a clean/dry repair area.
PRODUCTPanel wipe cloth.Degreaser.
Panel repair4Shape the filler to match the required panel contour.
METHODApply Dry Guide Coat to the filler area then hand sand with dust extraction block to achieve the required shape of repair.
PRODUCTRhynogrip HT Line strip. Grit P80 – P180 (size to suit). Dry Guide Coat.
EQUIPMENTDust extraction block.Dust extraction.
Panel repair2Sand the repair area to prepare for the application of body filler.
METHODMachine sand the repair area to a clean, bare metal surface or prepare the OE paint finish if using multi-substrate body filler.
PRODUCTRhynogrip HT Line Ultravent disc. Grit P80 – P180.
EQUIPMENTOrbital palm sander with 5mm orbit.Dust extraction.
Panel repair5Remove sanding scratches in the filler.
METHODHand sand the bodyfiller with dust extraction block to a smooth surface finish.
PRODUCTRhynogrip HT Line strip. Grit P180 (size to suit).
EQUIPMENTDust extraction block.Dust extraction.
Panel repair3Prepare the Evercoat™ body filler and apply to the repair area.
METHODMix the hardener with the filler to a 2% ratio (by weight) on the mixing board.
PRODUCTEvercoat Rage Ultra.
EQUIPMENTRhyno mixing board.Autofill spreader.
Panel repair6Machine sand the repair area to produce a feather edge.
METHODMachine sand the repair area to remove all scratches, leaving a feather edge into the surrounding paintwork.
PRODUCTRhynogrip HT Line Ultravent disc. Grit P180 – P320 (feather edge).
EQUIPMENTOrbital palm sander with 5mm orbit. Dust extraction.
METHODApply Dry Guide Coat then hand sand the repair area, leaving a smooth, primed surface finish.
PRODUCTRhynogrip HT Line strip Grit P320 (size to suit). For awkward areas use Rhynosoft P600 or Sponge SF. Dry Guide Coat.
EQUIPMENTDust extraction block.Dust extraction.
