Pompa Namol Secundar
3
Date: 7/24/2013 Project pos. no.: secondary sludge pump Temperature: Viscosity: pH value: Shaft deflection: Dry matter content: Starting torque: m³/h Hz min -1 kW Operating torque: 379 50 457 13.9 Max. requ. operating power: Volumetric efficiency: NPSHR (water, 20°C): Max. free passage : Connector left: Connector right: Connector material: Base: F Type of drive: IE2 Coupling or belt guard: Yes No Total weight: Approx. 660 kg Accessories: Remarks: Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No * Test only for complete pump units incl. drive motor. ** test only for complete units incl. drive motor and known operating mode. Created withCAPSpro Version 3.13.05 SS 316 Ti Gooseneck DN250, With flange according to EN1092-1/11 PN10 Seal type: Motor manufacturer: Shaft Ø pump chamber: HVSS High wear resistant special steel (-0.3mm) Blockring SS 316 Ti WC/SiC Shaft deflection/bar: 0.360 mm Motor type: Assembly specification Isolation class: 18.5 kW Power: 400/690 V Voltage: Frequency: Gooseneck DN250, With flange according to EN1092-1/11 PN10 SS 316 Ti HexaFlex 60 (60 mm/55 mm, 800/1600 Nm) 50 Hz Coupling guard, galvanized Motor efficiency classification: Base, type in-line, galvanized Thermistor sensor: Accessories/option Final inspection Tests Hydrostatic test** General visual inspection Pressure test buffer chamber Performance test** Customer inspection Alignment check* *** Final inspection Noise level at 1 m Grey cast iron 250 / Injection A Drehzahl (min -1 ): SK52-180MH/4 457 min -1 Seal carrier: Synchronization check Idle torque check Buffer chamber options: Getriebebau Nord Buffer fluid tank, pressurised Oil NBR SS 316 Ti Wear plates: Pressure disc/strain screw: Buffer chamber medium: Lobes: O-rings in touch with medium: 0.0 bar 0.4 bar Type: VX186-368Q Pressure at discharge: Differential pressure: Medium: Secondary sludge, 20.0 °C Pressure at inlet: Required volume flow: Process conditions 370 m³/h 20.0 °C 1000.0 kg/m³ Density: 3.00 0.4 bar 0.129 mm 291 Nm 13.9 kW 96.60% 2.5 % 486 Nm 1.0 mPas Pump specification Housing segments: Data sheet 85 mm 61 mm NBR / HiFlo / 4 Wings Design data Operating points:
description
Pompa Namol Secundar
Transcript of Pompa Namol Secundar
Date: 7/24/2013
Project pos. no.: secondary sludge pump
Temperature:Viscosity:pH value:
Shaft deflection: Dry matter content:
Starting torque:m³/h Hz min-1 kW Operating torque:
379 50 457 13.9 Max. requ. operating power:Volumetric efficiency:
NPSHR (water, 20°C):
Max. free passage :
Connector left:
Connector right:
Connector material:Base:
F Type of drive:IE2 Coupling or belt guard:
Yes No Total weight: Approx. 660 kg
Accessories:
Remarks:
Yes No Yes NoYes No Yes NoYes No Yes NoYes No Yes NoYes No Yes No
* Test only for complete pump units incl. drive motor.** test only for complete units incl. drive motor and known operating mode.
Created withCAPSpro Version 3.13.05
SS 316 Ti
Gooseneck DN250, With flange according to EN1092-1/11PN10
Seal type:
Motor manufacturer:
Shaft Ø pump chamber:HVSS High wear resistant special steel (-0.3mm)
Blockring SS 316 Ti WC/SiC Shaft deflection/bar: 0.360 mm
Motor type:
Assembly specification
Isolation class:
18.5 kWPower:400/690 VVoltage:
Frequency:
Gooseneck DN250, With flange according to EN1092-1/11PN10SS 316 Ti
HexaFlex 60 (60 mm/55 mm, 800/1600 Nm)50 Hz
Coupling guard, galvanizedMotor efficiency classification:
Base, type in-line, galvanized
Thermistor sensor:
Accessories/option
Final inspection
Tests
Hydrostatic test**
General visual inspectionPressure test buffer chamberPerformance test**
Customer inspection
Alignment check* ***
Final inspection
Noise level at 1 m
Grey cast iron 250 / Injection A
Drehzahl (min-1):SK52-180MH/4457 min-1
Seal carrier:
Synchronization checkIdle torque check
Buffer chamber options:
Getriebebau Nord
Buffer fluid tank, pressurisedOilNBRSS 316 TiWear plates: Pressure disc/strain screw:
Buffer chamber medium:Lobes:O-rings in touch with medium:
0.0 bar
0.4 bar
Type: VX186-368Q
Pressure at discharge:Differential pressure:
Medium: Secondary sludge, 20.0 °C
Pressure at inlet:Required volume flow:
Process conditions
370 m³/h20.0 °C1000.0 kg/m³Density:
3.00
0.4 bar
0.129 mm
291 Nm13.9 kW96.60%
2.5 %
486 Nm
1.0 mPas
Pump specification
Housing segments:
Data sheet
85 mm
61 mmNBR / HiFlo / 4 Wings
Design data
Operating points:
Recommended anchor bolts: L RSize: M 16 / Length min 60 mm Standard DIN DIN
DN DN250 DN250
D 395 mm 395 mm
k 350 mm 350 mm
d 22 mm 22 mmHole number 12 12
mm1961 Allowable horizontal forces: 1000N655 Allowable vertical forces: 1000N212 Allowable moments: 300Nm31
14000 a 609 a 6090 b 457 b 457
377 c 0 c 0560 d 120 d 120510200250 Dimensions shown in mm0 Changes of dimensions reserved0 General tolerances acc. to DIN ISO 2768 rough
18 Created withCAPSpro Version 3.13.05 Date:
Motor type
Customer:Vogelsang data:
Coupling guard, galvanizedHexaFlex 60 (60 mm/55 mm, 800/1600 Nm)SK52-180MH/4VX186-368Q
Quote no.:H
Position no.:
u
L 1 Order no.:L 2L 3
Flange data
Pump type
GooseneckCoupling or belt guard
Total weight
y
Space required for maintenance work:
L
v
www.vogelsang-gmbh.com
Holthöge 10-14, DE-49632 Essen (Oldenburg)
Gooseneck
W = 700 mm required, 1000 mm recommended
L 4
Hugo Vogelsang Maschinenbau GmbH
Not an assembly drawing. Concept sketch only!
L 5
BaseApprox. 660 kgBase, type in-line, galvanized
Type of drive
7/24/2013
x
h
y2
zy3
379
0.00
10.00
20.00
30.00
40.00
50.00
60.00
70.00
0.00
50.00
100.00
150.00
200.00
250.00
300.00
350.00
400.00
450.00
500.00
0 100 200 300 400 500 600
Pow
er in
[kW
]
Volu
me
flow
in [m
³/h]
Speed in [min-1]
Volume flow / speed at const. pressureVX186-368Q (HiFlo 4 Wings NBR)
Theoretical volume flow New pump Pump with gap (0.5 mm)
Operating points Water curve Operating power
CAPSpro Version 3.13.05
Water, 20,0 °C
ΔP = 0.4 bar
Medium:
