PLASMA / LCD DISPLAY SUPPORTMODEL: ALT50/2-BLK

ASSEMBLY INSTRUCTIONS

IMPORTANT INFORMATION!1) Before starting assembly please take time to familiarise yourself with the instructionsand the components listed on the back page, as this product could be unstable ifincorrectly installed.2) Do not place hot or cold items against or in close proximity to any glass surfaceunless an adequately thick insulating material is used to prevent such items coming intocontact with the glass.3) Do not strike the glass with hard or pointed items.4) When cleaning glass panels use a damp cloth or leather with washing up liquid orsoft soap if necessary; do not use washing powders or other substances containingabrasives as these may scratch the glass.5) Do not sit or stand upon horizontal glass surfaces.

Alphason Designs LimitedAlphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UKTel: +44 (0)1942 885600Fax: +44 (0)1942 876955info@alphasondesigns.com

www.alphasondesigns.com

Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.

Please Note:Total maximum load for this support must not exceed 70KgThis support must be assembled in accordance with these assembly instructions.Maximum load for bracket is 35Kg. Maximum load for glass shelves is 20kg.

PHILIPS SCREWDRIVER

PLEASE NOTE OTHER TOOLS REQUIRED:(NOT SUPPLIED)

01 03/08issue

3.

Place glass base panel on a clean, flat surface to

avoid scratching.

Attach plastic glides to the underside of base

panel with screws , using allen key .

STAGE 1

•

•

1.

x4x4

A

AA

h

hh

h

01 03/08issue

h

2.

B

C

C

C

m

i

Assemble side supports to central connectors , using screws

and washers and .

Ensure plastic washer , is used inbetween side support and

washer .

Please ensure that central connectors are fitted in the correct

locations. The bottom hole and the top two holes in side supports are

to be used.

STAGE 2•

•

•

x6

B Cm

CB

B

x6 x6

STAGE 3• Attach large felt pads to front and underside of framework as

illustrated on the left.

Secure framework to base panel using screws , washers

and in the central holes and screws and washers and in

the side holes as illustrated below.

Fix all screws finger

tight first for location

then ensure all screws

are fully tightened using

allen key .

.

x12A m

A

i

i

ii

ih

j

q

q

n

n

mn

q m n

p

q

p

p

p

q

n•

qq

m n

•

x4

x4

x2

x2

q

m

nn

m

j

s

s

s

s

Attach glass side panels to framework using screws and

washers and .

STAGE 4

•

4.

01 03/08issue

Carefully assemble glass back panel to framework using screws

washers and . Only fix each screw finger tight until all are in

position then ensure all screws are fully tightened using allen key .

Push fit plastic cover caps onto all four screw heads.

Fit cable tidy trims into holes in glass back panel .

STAGE 6

•

•

•

x4 x4

x4

m

x4x4x4

m

x4

DD

Dm

m

5.

qn

q n

q n

G

I

k

q

mn

6.

STAGE 5

Fix small felf pads to

the bottom edge of glass

back panel in

positions shown.

• o

G

o

G

Gn m

k

l G

q n

o

q

k

j

Attach 2 large felt pads to the back of each shelf frame .

STAGE 7

•

7.

01 03/08issue

Assemble both glass shelves to shelf frames from the

underside using screws washers and .

Only fix each screw finger tight until all are in position then

ensure all screws are fixed tightly using allen key .

STAGE 8

•

•

x8 x8

m

x4

x8

8.

9. STAGE 9

Fix both shelf frames securely through back panel and into

framework using screws washers and .

• G

nm

n

F Fp

pp

FG

F

F

r

mn

Fr m n

x4 x4 x4

m nr

E

E

F

E F

mn

F

E

j

r

r

r

r

Attach bracket plate to framework using screws washers

and .

STAGE 10

•

01 03/08issue

STAGE 12

x4

STAGE 13

•

10.

m nn m

x4 x4

m n

11.Fix adjustment knob, washer and screw through square hole in

hang on brackets .

STAGE 11

•

12.Attach hang-on brackets to back of screen using suitable

screws from fixing kit . Ensure brackets are fixed at the

correct height for viewing your screen.

Carefully hook brackets to back plate .

•

• Tighten base fixing screw on both hang-on brackets to secure

brackets in place.

You can now tilt your screen to your desired position by loosening

adjustment knob . Please ensure adjustment knob is fully

tightened when suitable position is found.

Congratulations your stand is now

complete!

•

•

13.

Base fixing

screw

u

u

u

tv

t

t

u

w

t

t

t

vv v

q

q

q

DESCRIPTION QTY

1

2

3

2

COMPONENT

CERTIFICATE OF CONFORMITY

01 03/08issue

A

B

2

4

4

GLASS SHELF

GLASS SIDE PANEL(These panels are handed left and right)

CENTRAL CONNECTOR

SIDE SUPPORT

GLASS BASE PANEL

2

PLASTIC GLIDE

GLIDE SCREWS

C

D

E

F

h

i

34

34

M8 PLASTIC WASHER

M8 WASHER

j

k

m

MODEL: ALT50/2-BLK

SHELF FRAME

PLASTIC COVER CAP

CABLE TIDY TRIM

4

2

ALLEN KEY 1

G

l

n

GLASS BACK PANEL 1

This document is your guarantee that the product has reached you in the highest of quality standards. Should you have any cause for complaint please return this document with your

correspondence to the address given at the bottom of the front page.

20

12

2

DESCRIPTION QTYCOMPONENT

1SET OF FIXING SCREWS

AND WASHERS(FOR FLATSCREEN FIXING)

s

t

v

w

01 03/08issue

M8 x 30 SCREW

M8 x 47 SCREW

M8 x 55 SCREW

p

q

r

BRACKET PLATE

HANG ON BRACKET 2

1

LARGE FELT PAD

SMALL FELT PADo 2

16

ADJUSTMENT KNOB KIT 2

u