PISCO push-in fitting, superior in operability and ... · PISCO push-in fitting, superior in...

No, SFD 1-02e

øD øD øD øD øD

øDøD

øDøD øD

øD øDR R Rc øD Rc R RR

R

R

Model code

Tube O.D. øD

R A B L C Hex.

PC4-M5□ 4 M5×0.83 ［3.2］ 20 17 ［16.8］

14.9 103 19.8 16.8

①：There are no dimensional changes.②：There are dimensional changes.　　Upper character: Current model, Bottom character: New model

1. Reduced in weight for all the models. 　 Average of about 25% reduction in weight has been achieved　 and some models have been downsized.

2. The gasket material is unified to PPS.　 Fall prevention type with improved corrosion resistance is applied.

3. Recommended screw tightening torque is reduced.　 We reviewed the tightening torque for all the taper pipe thread sizes.　 *Please refer to the last page.

Easier to use!

▼ Please refer to details from next page.

The old and new dimension comparison table of Tube Fitting Standard series

These changes shall be implemented sequentially from November 1, 2014Type of subject models

How to use this table

Satisfying customer’s needs by saving the core structure.

PC POC PCF PM PMF PL PLL PB PD PXStraight Inner Hex.

StraightFemale Straight

Bulkhead Union

Bulkhead Female Straight Elbow Long Elbow Branch Tee Run Tee Branch Y

Model CodePCøD-R

Model CodePOCøD-R

Model CodePCFøD-Rc

Model CodePMøD

Model CodePMFøD-Rc

Model CodePLøD-R

Model CodePLLøD-R

Model CodePBøD-R

Model CodePDøD-R

Model CodePXøD-R

PISCO push-in fitting, superior in operability anddurability, has been redesigned to smart type.

(10 configurations.) 　　

● Current model ● New model

2

Unit：㎜

Model codeTube O.D.

øDR A B L C Hex. øP

Orifice（ø㎜）

Weight（g）

PC4-M5□ 4 M5×0.83 ［3.2］ 20 17 ［16.8］

14.9 10 -1.8 6.3

3 19.8 16.8 2.4 5.6

PC4-M50□ 4 M5×0.83 ［3.2］ 22.9 19.9 ［19.7］

14.9 8 9.71.8 6.6

3 22.7 19.7 2.4 6.1

PC4-M6□ 4 M6×1 421 17

14.9 10 - 36.4

20.8 16.8 6.0

PC4-01□ 4 R1/8 8 21 17 14.9 10 - 38.37.4

PC4-02□ 4 R1/4 1121 15

14.9 14 - 3 1622.5 16.5

PC6-M5□ 6 M5×0.83 ［3.2］ 22.1 19.1 ［18.9］

17 12 -1.8 9.2

3 21.9 18.9 2.4 8.1

PC6-M6□ 6 M6×1 423.1 19.1

17 12 - 39.4

22.9 18.9 8.5

PC6-01□ 6 R1/8 822.6 18.6

17 12 -4.6 9.3

22.3 18.3 5 8.2

PC6-02□ 6 R1/4 1124.6 18.5

17 14 -4.6 18

23.7 17.6 5 15

PC6-03□ 6 R3/8 1223.6 17.2

17 17 -4.6

2824.5 18.1 5

PC8-01□ 8 R1/8 8 27.9 23.9 18.2 14 - 61614

PC8-02□ 8 R1/4 11 26.6 20.6 18.2 14 - 71614

PC8-03□ 8 R3/8 1223.9 17.6

18.2 17 - 724

25.5 19.2 25

PC10-01□ 10 R1/8 8 30.3 26.3 20.7 17 - 62421

PC10-02□ 10 R1/4 11 29.8 23.8 20.7 17 - 8.52119

PC10-03□ 10 R3/8 12 29.3 23 20.7 17 -8.5 279 24

PC10-04□ 10 R1/2 1530.3 22.1

20.7 21 -8.5 50

30.4 22.2 9 46

PC12-02□ 12 R1/4 11 35.9 29.9 23.3 21 - 8.54437

PC12-03□ 12 R3/8 12 31.9 25.6 23.3 21 - 113629

PC12-04□ 12 R1/2 15 33.9 25.7 23.3 21 - 115043

PC16-03□ 16 R3/8 12 39.3 33 24.8 24 - 115854

PC16-04□ 16 R1/2 15 41.3 33.1 24.8 24 - 136663

・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type PC4-M50

øD

R

øP

B L C

A ALB Hex.

Hex.

R R


øD

R

Hex.

øP

BL C

A ALB

R R

Hex.

2014 NEW PRODUCTS

PC Straight（mm-R ）


3

Unit：㎜

Model codeTube O.D.

øDR A B L C Hex.

Orifice（ø㎜）

Weight（g）

PC5/32-M5□ 5/32 M5×0.83 ［3.2］ 20 17 ［16.8］

14.9 101.8 6.3

3 19.8 16.8 2.4 5.6

PC5/32-01□ 5/32 R1/8 8 21 17 14.9 10 38.37.4

PC5/32-02□ 5/32 R1/4 1121 15

14.9 14 3 1622.5 16.5

PC3/16-M5□ 3/16 M5×0.83 ［3.2］ 22.5 19.5 ［19.3］

17.4 121.8 9.5

3 22.3 19.3 2.4 8.6

PC3/16-01□ 3/16 R1/8 823 19

17.4 12 49.8

22.7 18.7 9.0

PC3/16-02□ 3/16 R1/4 1125 18.9

17.4 14 418

24.1 18 16

PC1/4-M5□ 1/4 M5×0.83 ［3.2］ 22.1 19.1 ［18.9］

17 121.8 9

3 21.9 18.9 2.4 8.0

PC1/4-01□ 1/4 R1/8 822.6 18.6

17 124.6 9.1

22.3 18.3 5.3 8.0

PC1/4-02□ 1/4 R1/4 1124.6 18.5

17 144.6 18

23.7 17.6 5.3 15

PC1/4-03□ 1/4 R3/8 1223.6 17.2

17 174.6 27

24.5 18.1 5.3 28

PC5/16-01□ 5/16 R1/8 8 27.9 23.9 18.2 14 61614

PC5/16-02□ 5/16 R1/4 11 26.6 20.6 18.2 14 71614

PC5/16-03□ 5/16 R3/8 1223.9 17.6

18.2 17 724

25.5 19.2 25

PC3/8-01□ 3/8 R1/8 8 30.3 26.3 20.7 17 62422

PC3/8-02□ 3/8 R1/4 11 29.8 23.8 20.7 17 8.52119

PC3/8-03□ 3/8 R3/8 12 29.3 23 20.7 17 8.52725

PC3/8-04□ 3/8 R1/2 1530.3 22.1

20.7 21 8.551

30.4 22.2 47

PC1/2-02□ 1/2 R1/4 11 35.7 29.7 23.1 21 8.54236

PC1/2-03□ 1/2 R3/8 12 31.7 25.4 23.1 21 113529

PC1/2-04□ 1/2 R1/2 15 33.7 25.5 23.1 21 114943

PC5/8-03□ 5/8 R3/8 12 39.3 33 24.8 24 115854

PC5/8-04□ 5/8 R1/2 15 41.3 33.1 24.8 24 136663



øD

R

Hex.

øP

BL C

A ALB

R R

Hex.


øD

R

øP

B L C

A ALB Hex.

Hex.

R R


PC Straight（inch-R）


4

Unit：㎜

Model codeTube O.D.

øDR A B L C Hex.

Orifice（ø㎜）

Weight（g）

PC4-U10U 4 No.10-32UNF 320 17

14.9 7/161.8 6.9

19.8 16.8 2.4 6.2

PC4-N0U 4 1/16-27NPT 8 21 16.9 14.9 7/163 7.6

2.4 6.5

PC4-N1U 4 1/8-27NPT 8 21 16.9 14.9 7/16 39.58.3

PC4-N2U 4 1/4-18NPT 1121 15.2

14.9 9/16 3 1722.5 16.7

PC6-U10U 6 No.10-32UNF 322.1 19.1

17 1/21.8 11

21.9 18.9 2.4 8.7

PC6-N0U 6 1/16-27NPT 8 26.2 22.1 17 1/23 13

2.4 11

PC6-N1U 6 1/8-27NPT 822.6 18.4

17 1/24.6 11

22.3 18.1 5 8.8

PC6-N2U 6 1/4-18NPT 1124.6 18.8

17 9/164.6 18

23.7 18.4 5 15

PC6-N3U 6 3/8-18NPT 1223.6 17.5

17 11/164.6 28

24.5 18.4 5.3 30

PC8-N1U 8 1/8-27NPT 8 27.9 23.8 18.2 9/16 61614

PC8-N2U 8 1/4-18NPT 11 26.6 20.8 18.2 9/16 71615

PC8-N3U 8 3/8-18NPT 1223.9 17.8

18.2 11/16 725

25.5 19.4 26

PC10-N1U 10 1/8-27NPT 8 30.3 26.2 20.7 11/16 62223

PC10-N2U 10 1/4-18NPT 11 29.8 24 20.7 11/16 8.52220

PC10-N3U 10 3/8-18NPT 12 29.3 23.2 20.7 11/168.5 289 25

PC10-N4U 10 1/2-14NPT 1530.3 22.2

20.7 7/88.5 52

30.4 22.3 9 48

PC12-N2U 12 1/4-18NPT 11 35.9 30.1 23.3 7/8 8.54839

PC12-N3U 12 3/8-18NPT 12 31.9 25.8 23.3 7/8 113932

PC12-N4U 12 1/2-14NPT 15 33.9 25.8 23.3 7/8 115246

PC16-N3U 16 3/8-18NPT 12 39.3 33.2 24.8 1 116961

PC16-N4U 16 1/2-14NPT 15 41.3 33.2 24.8 1 137669

・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.


øD

R

øP

B L C

A ALB Hex.

Hex.

R RMetric thread type PC4-M50

øD

R

Hex.

øP

BL C

A ALB

R R

Hex.

2014 NEW PRODUCTS

PC Straight（mm - NPT）

Unified Unified


5

Unit：㎜

Model codeTube O.D.

øDR A B L C Hex.

Orifice（ø㎜）

Weight（g）

PC5/32-U10U 5/32 No.10-32UNF 320 17

14.9 7/161.8 6.9

19.8 16.8 2.4 6.2

PC5/32-N0U 5/32 1/16-27NPT 8 21 16.9 14.9 7/16 37.66.5

PC5/32-N1U 5/32 1/8-27NPT 8 21 16.9 14.9 7/16 39.58.3

PC5/32-N2U 5/32 1/4-18NPT 1121 15.2

14.9 9/16 3 1722.5 16.7

PC3/16-U10U 3/16 No.10-32UNF 322.5 19.5

17.4 1/21.8 11

22.3 19.3 2.4 9.2

PC3/16-N0U 3/16 1/16-27NPT 8 26.6 22.5 17.4 1/2 31412

PC3/16-N1U 3/16 1/8-27NPT 823 18.8

17.4 1/2 412

22.7 18.5 10

PC3/16-N2U 3/16 1/4-18NPT 1125 19.2

17.4 9/16 419

24.1 18.3 16

PC3/16-N3U 3/16 3/8-18NPT 1224 17.9

17.4 11/16 429

24.9 18.8 30

PC1/4-U10U 1/4 No.10-32UNF 322.1 19.1

17 1/21.8 11

21.9 18.9 2.4 8.6

PC1/4-N0U 1/4 1/16-27NPT 8 26.2 22.1 17 1/2 31311

PC1/4-N1U 1/4 1/8-27NPT 822.6 18.4

17 1/24.6 11

22.3 18.1 5.3 8.6

PC1/4-N2U 1/4 1/4-18NPT 1124.6 18.8

17 9/164.6 18

23.7 17.9 5.3 15

PC1/4-N3U 1/4 3/8-18NPT 1223.6 17.5

17 11/164.6 28

24.5 18.4 5.3 29

PC5/16-N1U 5/16 1/8-27NPT 8 27.9 23.8 18.2 9/16 61614

PC5/16-N2U 5/16 1/4-18NPT 11 26.6 20.8 18.2 9/16 71615

PC5/16-N3U 5/16 3/8-18NPT 1223.9 17.8

18.2 11/16 725

25.5 19.4 26

PC3/8-N1U 3/8 1/8-27NPT 8 30.3 26.2 20.7 11/16 62623

PC3/8-N2U 3/8 1/4-18NPT 11 29.8 24 20.7 11/16 8.52320

PC3/8-N3U 3/8 3/8-18NPT 12 29.3 23.2 20.7 11/16 8.52926

PC3/8-N4U 3/8 1/2-14NPT 1530.3 22.2

20.7 7/8 8.552

30.4 22.3 49

PC1/2-N2U 1/2 1/4-18NPT 11 35.7 29.9 23.1 7/8 8.54838

PC1/2-N3U 1/2 3/8-18NPT 12 31.7 25.6 23.1 7/8 113931

PC1/2-N4U 1/2 1/2-14NPT 15 33.7 25.6 23.1 7/8 115245

PC5/8-N3U 5/8 3/8-18NPT 12 39.3 33.2 24.8 1 116961

PC5/8-N4U 5/8 1/2-14NPT 15 41.3 33.2 24.8 1 137669

・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.


øD

R

Hex.

øP

BL C

A ALB

R R

Hex.


øD

R

øP

B L C

A ALB Hex.

Hex.

R R


PC Straight（inch - NPT）

Unified Unified


6

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

POC4-M5□ 4 M5×0.83 ［3.2］ 19.9 16.9 ［16.7］

14.92

9.72 5.6

3 19.7 16.7 2.5 2.6 4.6

POC4-M6□ 4 M6×1 420.9 16.9

14.93

9.73.1 5.9

20.7 16.7 2.5※ 2.6※ 5.4

POC4-01□ 4 R1/8 821 17

14.9 2.5 9.7 2.67.6

20 16 6.6

POC6-M5□ 6 M5×0.83 ［3.2］ 23 20 ［19.8］

172

11.82 8.5

3 21.3 18.3 2.5 2.6 5.6

POC6-M6□ 6 M6×1 422.5 18.5

17 3 11.8 3.16.9

22.3 18.3 6.3

POC6-01□ 6 R1/8 822.6 18.6

17 4 11.8 4.18.1

22.1 18.1 7.6

POC6-02□ 6 R1/4 1122.6 16.5

17 414

4.115

21.3 15.2 13.7 13

POC8-01□ 8 R1/8 827.9 23.9

18.2 5 13.7 5.114

25.9 21.9 8.8

POC8-02□ 8 R1/4 1126.6 20.6

18.2 6 13.7 6.215

25.1 19.1 13

POC8-03□ 8 R3/8 1223.9 17.6

18.2 6 16.8 6.223

22.2 15.9 19

POC10-01□ 10 R1/8 8 30.3 26.3 20.7 517.7

5.123

17.5 17

POC10-02□ 10 R1/4 11 29.8 23.8 20.7 617.7

6.223

17.5 20

POC10-03□ 10 R3/8 12 29.3 23 20.7 617.7

6.228

17.5 26

POC10-04□ 10 R1/2 15 30.3 22.1 20.7 6 20.8 6.24945

POC12-02□ 12 R1/4 11 35.9 29.9 23.3 6 20.8 6.24029

POC12-03□ 12 R3/8 12 31.9 25.6 23.3 8 20.8 8.23431

POC12-04□ 12 R1/2 15 33.9 25.7 23.3 8 20.8 8.24945

POC16-03□ 16 R3/8 12 39.3 33 24.8 10 26 10.26461

POC16-04□ 16 R1/2 1542.3 34.1

24.8 12 26 12.273

40.3 32.1 65※ Avoid Lock-claws defect by interference of hexagon key wrench, inner hexagon size is reviewed and the orifice size was changed. ・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type

øD

R

øP

B L C

AH

ex.

ALB

RMetric thread type

øD

R

øP

BL C

AH

ex.

ALB

R

2014 NEW PRODUCTS

POC Inner Hex. Straight（mm - R ）


7

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

POC1/4-M5□ 1/4 M5×0.8 323 20

172

11.82 8.2

21.3 18.3 2.5 2.6 5.6

POC1/4-01□ 1/4 R1/8 822.6 18.6

17 4 11.8 4.18

22.1 18.1 7.5

POC1/4-02□ 1/4 R1/4 1122.6 16.5

17 414

4.114

21.3 15.2 13.7 12

POC5/16-01□ 5/16 R1/8 827.9 23.9

18.2 5 13.7 5.114

25.9 21.9 8.8

POC5/16-02□ 5/16 R1/4 1126.6 20.6

18.2 6 13.7 6.215

25.1 19.1 13

POC5/16-03□ 5/16 R3/8 1223.9 17.6

18.2 6 16.8 6.223

22.2 15.9 19

POC3/8-02□ 3/8 R1/4 11 29.8 23.8 20.7 617.7

6.223

17.5 21

POC3/8-03□ 3/8 R3/8 12 29.3 23 20.7 617.7

6.229

17.5 27

POC3/8-04□ 3/8 R1/2 15 30.3 22.1 20.7 6 20.8 6.24946


Metric thread type

øD

R

øP

B L C

AH

ex.

ALB

RMetric thread type

øD

R

øP

BL C

AH

ex.

ALB

R


POC Inner Hex. Straight（inch - R ）


8

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

POC4-U10U□ 4 No.10-32UNF 319.9 16.9

14.9 3/32 9.7 2.55.4

19.7 16.7 4.6

POC4-N1U□ 4 1/8-27NPT 821 16.9

14.9 3/32 9.7 2.57.8

20 15.9 6.5

POC6-U10U□ 6 No.10-32UNF 323 20

17 3/32 11.8 2.58.1

21.3 18.3 5.6

POC6-N1U□ 6 1/8-27NPT 822.6 18.4

17 5/32 11.8 4.18.4

22.1 17.9 7.6

POC8-N1U□ 8 1/8-27NPT 827.9 23.8

18.2 3/16 13.7 4.915

25.9 21.8 9

POC8-N2U□ 8 1/4-18NPT 1126.6 20.8

18.2 7/32 13.7 5.716

25.1 19.3 13・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

øD

R

øP

B L C

AH

ex.

ALB

RMetric thread type

øD

R

øP

BL C

AH

ex.

ALB

RUnified Unified

2014 NEW PRODUCTS

POC Inner Hex. Straight（mm - NPT）


9

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

POC5/32-U10U□ 5/32 No.10-32UNF 319.9 16.9

14.9 3/32 9.7 2.55.4

19.7 16.7 4.6

POC5/32-N1U□ 5/32 1/8-27NPT 821 16.9

14.9 3/32 9.7 2.57.8

20 15.9 6.5

POC3/16-U10U□ 3/16 No.10-32UNF 323.4 20.4

17.4 3/32 11.8 2.58.5

21.7 18.7 6.1

POC3/16-N1U□ 3/16 1/8-27NPT 823 18.8

17.4 1/8 11.8 3.39.2

22.5 18.3 8.3

POC1/4-U10U□ 1/4 No.10-32UNF 323 20

17 3/32 11.8 2.58

21.3 18.3 5.6

POC1/4-N1U□ 1/4 1/8-27NPT 822.6 18.4

17 3/32 11.8 4.18.3

22.1 17.9 7.4

POC1/4-N2U□ 1/4 1/4-18NPT 1122.6 16.8

17 5/3214

4.115

21.3 15.5 13.7 13

POC5/16-N1U□ 5/16 1/8-27NPT 827.9 23.8

18.2 3/16 13.7 4.915

25.9 21.8 9

POC5/16-N2U□ 5/16 1/4-18NPT 1126.6 20.8

18.2 7/32 13.7 5.716

25.1 19.3 13

POC5/16-N3U□ 5/16 3/8-18NPT 1223.9 17.8

18.2 7/32 16.8 5.723

22.2 16.1 19

POC3/8-N1U□ 3/8 1/8-27NPT 8 30.3 26.2 20.7 3/1617.7

4.924

17.5 18

POC3/8-N2U□ 3/8 1/4-18NPT 11 29.8 24 20.7 7/3217.7

5.723

17.5 22

POC3/8-N3U□ 3/8 3/8-18NPT 12 29.3 23.2 20.7 7/3217.7

5.730

17.5 28

POC3/8-N4U□ 3/8 1/2-14NPT 15 30.3 22.2 20.7 7/32 20.8 5.75045

POC1/2-N2U□ 1/2 1/4-18NPT 11 35.7 29.9 23.1 7/32 20.8 5.73930

POC1/2-N3U□ 1/2 3/8-18NPT 1235.1 29

23.1 5/1622

8.246

31.7 25.6 20.8 30

POC1/2-N4U□ 1/2 1/2-14NPT 1538.1 30

23.1 5/1623

8.268

33.7 25.6 20.8 44・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

øD

R

øP

B L C

AH

ex.

ALB

RMetric thread type

øD

R

øP

BL C

AH

ex.

ALB

RUnified Unified


POC Inner Hex. Straight（inch - NPT ）


10

Unit：㎜

Model codeTube O.D.

øDRc A B E øP1 øP2 C Hex. T

Orifice（ø㎜）

Weight（g）

PCF4-M5□ 4 M5×0.8 4.5 21.4- 10 -

14.9 10- 2.5 8.8

8 9.7 9 4 3 7.6

PCF4-01□ 4 Rc1/8 724.4 - 11 -

14.9 14-

316

23.9 10 9.7 13.8 5 13

PCF4-02□ 4 Rc1/4 9.527.4 - 12 -

14.9 17-

324

26.9 13 9.7 16.8 6 19

PCF6-M5□ 6 M5×0.8 5 22- 12 -

17 12-

4.112

9 11.8 9 5 9.5

PCF6-01□ 6 Rc1/8 726.5 - 13 -

17 14- 4.6 18

26 10 11.8 13.8 5 5 15

PCF6-02□ 6 Rc1/4 9.529.5 - 13 -

17 17- 4.6 25

29 13 11.8 16.8 6 5 21

PCF6-03□ 6 Rc3/8 10.530.5 - 13 -

17 21- 4.6 32

30 14 11.8 20.8 6.5 5 29

PCF8-01□ 8 Rc1/8 728 - 14.5 -

18.2 14- 6 20

27.2 10 13.7 13.8 5 7 16

PCF8-02□ 8 Rc1/4 9.531 - 15 -

18.2 17- 6 27

30.2 13 13.7 16.8 6 7 22

PCF8-03□ 8 Rc3/8 10.532 - 15.5 -

18.2 21- 6 37

31.2 14 13.7 20.8 6.5 7 30

PCF10-02□ 10 Rc1/4 9.533.7 -

17.5-

20.7 17- 8.5 33

32.7 13 16.8 6 9 28

PCF10-03□ 10 Rc3/8 10.534.7 -

17.5-

20.7 21- 8.5 42

33.7 14 20.8 6.5 9 37

PCF12-02□ 12 Rc1/4 9.535.8 -

20.8-

23.3 21-

1157

34.8 13.5 16.8 6.5 42

PCF12-03□ 12 Rc3/8 10.536.8 -

20.8-

23.3 21-

1151

36.3 14 20.8 6.5 44

PCF12-04□ 12 Rc1/2 1340.8 -

20.8-

23.3 24-

1162

39.3 17 25 7 54

PCF16-03□ 16 Rc3/8 10.538.3 -

26-

24.8 27-

14.297

37.3 15.5 20.8 8 71

PCF16-04□ 16 Rc1/2 1341.3 -

26-

24.8 27- 14 94

40.8 18 25 8 15 76・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

øD

RcHex.

øP1

øP2

BE

T

CA

øD

RcHex.

øPB

CA

2014 NEW PRODUCTS

PCF Female Straight（mm - Rc ）


11

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

PCF5/32-01□ 5/32 Rc1/8 724.4 - 11 -

14.9 14-

316

23.9 10 9.7 13.8 5 13

PCF5/32-02□ 5/32 Rc1/4 9.527.4 - 12 -

14.9 17-

324

26.9 13 9.7 16.8 6 19

PCF3/16-01□ 3/16 Rc1/8 726.9 - 13 -

17.4 14-

419

26.4 10 11.8 13.8 5 16

PCF3/16-02□ 3/16 Rc1/4 9.529.9 - 13 -

17.4 17-

425

29.4 13 11.8 16.8 6 22

PCF1/4-01□ 1/4 Rc1/8 726.5 - 13 -

17 14- 4.6 18

26 10 11.8 13.8 5 5.3 15

PCF1/4-02□ 1/4 Rc1/4 9.529.5 - 13 -

17 17- 4.6 25

29 13 11.8 16.8 6 5.3 21

PCF1/4-03□ 1/4 Rc3/8 10.530.5 - 13 -

17 21- 4.6 32

30 14 11.8 20.8 6.5 5.3 29

PCF5/16-01□ 5/16 Rc1/8 728 - 14.5 -

18.2 14- 6 20

27.2 10 13.7 13.8 5 7 16

PCF5/16-02□ 5/16 Rc1/4 9.531 - 15 -

18.2 17- 6 27

30.2 13 13.7 16.8 6 7 22

PCF5/16-03□ 5/16 Rc3/8 10.532 - 15.5 -

18.2 21- 6 36

31.2 14 13.7 20.8 6.5 7 30

PCF3/8-02□ 3/8 Rc1/4 9.533.7 -

17.5-

20.7 17-

8.533

32.7 13 16.8 6 29

PCF3/8-03□ 3/8 Rc3/8 10.534.7 -

17.5-

20.7 21-

8.543

33.7 14 20.8 6.5 37

PCF1/2-02□ 1/2 Rc1/4 9.535.6 -

20.8-

23.1 21-

1155

34.6 13.5 16.8 6.5 41

PCF1/2-03□ 1/2 Rc3/8 10.536.6 -

20.8-

23.1 21-

1149

36.1 14 20.8 6.5 44

PCF1/2-04□ 1/2 Rc1/2 1340.6 -

20.8-

23.1 24-

1161

39.1 17 25 7 53・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

øD

RcHex.

øP1

øP2

BE

T

CA

øD

RcHex.

øP

B

CA


PCF Female Straight（inch - Rc ）


12

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

PCF4-N1U□ 4 1/8-27NPT 724.4 - 11 -

14.9 9/16-

316

23.9 10 9.7 13.8 5 13

PCF4-N2U□ 4 1/4-18NPT 9.527.4 - 12 -

14.9 11/16-

322

26.9 13 9.7 17.2 6 20

PCF6-N1U□ 6 1/8-27NPT 726.5 - 13 -

17 9/16- 4.6 18

26 10 11.8 13.8 5 5 15

PCF6-N2U□ 6 1/4-18NPT 9.529.5 - 13 -

17 11/16- 4.6 25

29 13 11.8 17.2 6 5 22

PCF8-N1U□ 8 1/8-27NPT 728 - 14.5 -

18.2 9/16- 6 18

27.2 10 13.7 13.8 5 7 16

PCF8-N2U□ 8 1/4-18NPT 9.531 - 15 -

18.2 11/16- 6 28

30.2 13 13.7 17.2 6 7 23

PCF10-N2U□ 10 1/4-18NPT 9.533.7 - 17.5 -

20.7 11/16- 8.5 34

32.7 13 17.5 16.8 6 9 29

PCF12-N2U□ 12 1/4-18NPT 9.536.8 -

20.8-

23.3 7/8-

1159

34.8 13.5 16.8 6.5 44

PCF12-N3U□ 12 3/8-18NPT 10.536.8 -

20.8-

23.3 7/8-

1154

36.3 14 21.8 6.5 48・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

øD

RcHex.

øP1

øP2

BE

T

CA

øD

RcHex.

øPB

CA

2014 NEW PRODUCTS

PCF Female Straight（mm - NPT）


13

Unit：㎜

Model codeTube O.D.


Orifice（ø㎜）

Weight（g）

PCF5/32-U10U□ 5/32 No.10-32UNF 4.5 21.4- 11 -

14.9 7/16- 2.5 12

8 9.7 9 4 3 8.2

PCF5/32-N1U□ 5/32 1/8-27NPT 724.4 - 11 -

14.9 9/16-

316

23.9 10 9.7 13.8 5 13

PCF5/32-N2U□ 5/32 1/4-18NPT 9.527.4 - 12 -

14.9 11/16-

322

26.9 13 9.7 17.2 6 20

PCF3/16-U10U□ 3/16 No.10-32UNF3.5 23.4 -

11.8-

17.4 1/2-

3.914

5 22.4 9 9 5 11

PCF3/16-N1U□ 3/16 1/8-27NPT 726.9 - 13 -

17.4 9/16-

419

26.4 10 11.8 13.8 5 15

PCF3/16-N2U□ 3/16 1/4-18NPT 9.529.9 - 13 -

17.4 11/16-

426

29.4 13 11.8 17.2 6 23

PCF1/4-U10U□ 1/4 No.10-32UNF3.5 23 -

11.8-

17 1/2-

3.913

5 22 9 9 5 10

PCF1/4-N1U□ 1/4 1/8-27NPT 726.5 - 13 -

17 9/16- 4.6 18

26 10 11.8 13.8 5 5.3 15

PCF1/4-N2U□ 1/4 1/4-18NPT 9.529.5 - 13 -

17 11/16- 4.6 25

29 13 11.8 17.2 6 5.3 22

PCF1/4-N3U□ 1/4 3/8-18NPT 10.530.5 - 13 -

17 7/8- 4.6 35

30 14 11.8 21.8 6.5 5.3 33

PCF5/16-N1U□ 5/16 1/8-27NPT 728 - 14.5 -

18.2 9/16- 6 18

27.2 10 13.7 13.8 5 7 16

PCF5/16-N2U□ 5/16 1/4-18NPT 9.531 - 15 -

18.2 11/16- 6 28

30.2 13 13.7 17.2 6 7 23

PCF5/16-N3U□ 5/16 3/8-18NPT 10.532 - 15.5 -

18.2 7/8- 6 40

31.2 14 13.7 21.8 6.5 7 34

PCF3/8-N1U□ 3/8 1/8-27NPT 730.8 -

17.5-

20.7 11/16- 7.5 34

29.7 11 13.8 6 8.3 27

PCF3/8-N2U□ 3/8 1/4-18NPT 9.533.7 -

17.5-

20.7 11/16-

8.534

32.7 13 16.8 6 29

PCF3/8-N3U□ 3/8 3/8-18NPT 10.534.7 -

17.5-

20.7 7/8-

8.546

33.7 14 21.8 6.5 41

PCF1/2-N2U□ 1/2 1/4-18NPT 9.536.6 -

20.8-

23.1 7/8-

1158

34.6 13.5 16.8 6.5 43

PCF1/2-N3U□ 1/2 3/8-18NPT 10.536.6 -

20.8-

23.1 7/8-

1153

36.1 14 21.8 6.5 47

PCF1/2-N4U□ 1/2 1/2-14NPT 1340.6 -

20.8-

23.1 1-

1167

39.1 17 25.2 7 58・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

øD

RcHex.

øP1

øP2

BE

T

CA

øD

RcHex.

øP

B

CA


PCF Female Straight（inch - NPT）


14

Unit：㎜

Model codeTube O.D.

øDM B E A øP C Hex. T

Orifice（ø㎜）

Weight（g）

PM4□ 4 M12×1 30.810.4 15

10.8 14.9 14 4 3 119.5 14.8

PM6□ 6 M14×1 34.911 18

12.5 17 17 44.6

169.5 19 5

PM8□ 8 M16×1 37.414.3 16.8

14.6 18.2 19 46 20

10.5 19.4 7 19

PM10□ 10 M20×1 42.412.7 23

18.5 20.7 24 58 39

11.9 21.6 9 35

PM12□ 12 M22×1 47.612.3 29

20.4 23.3 27 6 1157

13.2 24.2 52

PM16□ 16 M28×1.551 5.4 40.2 ‐

24.8 32 613 80

50.6 13.2 27.2 25.5 15 73

PM5/32□ 5/32 M12×1 30.810.4 15

10.8 14.9 14 4 311

9.5 14.8 10

PM3/16□ 3/16 M14×1 35.711.4 18

12.5 17.4 17 4 4 169.9 19

PM1/4□ 1/4 M14×1 34.911 18

12.5 17 17 44.6

169.5 19 5.3

PM5/16□ 5/16 M16×1 37.414.3 16.8

14.6 18.2 19 46 20

10.5 19.4 7 19

PM3/8□ 3/8 M20×1 42.412.7 23

18.5 20.7 24 58 39

11.9 21.6 8.5 36

PM1/2□ 1/2 M22×1 47.212.1 29

20.4 23.1 27 611 55

13 24.2 11.7 51・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

2-ø

D

2-Hex.

øP

BE

2-CM

A2-T

2-ø

D

2-Hex.ø

P

BE

2-CM

A2-T

2014 NEW PRODUCTS

PM Bulkhead Union（mm & inch - mm nut）


15

Unit：㎜

Model codeTube O.D.

øDM B E A øP C Hex. T

Orifice（ø㎜）

Weight（g）

PM5/32U□ 5/32 1/2-20UNF 30.810.4 15 10.8

14.9 9/16 5 3.0 129.5 14.8 11.3

PM3/16U□ 3/16 9/16-18UNF 35.711.4 18

12.5 17.4 11/16 5.5 4.0 20

9.9 19 21

PM1/4U□ 1/4 9/16-18UNF 34.911 18

12.5 17 11/16 5.54.6

209.5 19 5.3

PM5/16U□ 5/16 5/8-18UNF 37.414.3 16.8

14.3 18.2 3/4 5.56.0

2310.5 19.4 7.0

PM3/8U□ 3/8 7/8-14UNF 42.412.7 23 18.5

20.7 1 78.0 49

11.9 21.6 20.2 8.5 48

PM1/2U□ 1/2 7/8-14UNF 47.212.1 29

20.4 23.1 1 711.0 51

13 24.2 11.7 49・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

2-ø

D

2-Hex.

øP

BE

2-CM

A2-T

2-ø

D

2-Hex.

øP

BE

2-CM

A2-T


PM Bulkhead Union（inch - inch nut ）


16

Unit：㎜

Model codeTube O.D.

øDRc M B E1 E2 A C øP Hex.1 Hex.2 T1 T2

Orifice（ø㎜）

Weight（g）

PMF4-01□ 4 Rc1/8 M12×124.5 9.9 10

7 14.9-

14 14 4-

319

24.2 9 9 13.8 5 17

PMF4-02□ 4 Rc1/4 M12×1 27.59.9 13

9.5 14.9-

14 17 4-

325

9 12.3 16.8 6 22

PMF6-01□ 6 Rc1/8 M14×127.1 11.9

10 7 17-

17 17 4- 4.6 29

26.4 10.2 13.8 6 5 25

PMF6-02□ 6 Rc1/4 M14×130.1 11.9 13

9.5 17-

17 17 4- 4.6 29

28.7 10.2 12.3 16.8 6 5 26

PMF6-03□ 6 Rc3/8 M14×131.1 11.9

14 10.5 17-

17 19 4- 4.6 30

30.4 10.2 19.5 6 5 29

PMF8-01□ 8 Rc1/8 M16×129 13.5

10 7 18.2-

19 19 4- 6 39

27 9.8 13.8 6 7 30

PMF8-02□ 8 Rc1/4 M16×132 13.5

13 9.5 18.2-

19 19 4- 6 41

30 9.8 16.8 6 7 32

PMF8-03□ 8 Rc3/8 M16×133 13.5

14 10.5 18.2-

19 19 4- 6 35

31 9.8 19.5 6 7 30

PMF10-02□ 10 Rc1/4 M20×134.8 14.9 14

9.5 20.7-

24 24 5- 8.5 78

32.7 11.1 13 16.8 7 9 55

PMF10-03□ 10 Rc3/8 M20×135.8 14.9 15

10.5 20.7-

24 24 5- 8.5 73

33.7 11.1 14 20.8 7 9 56

PMF12-02□ 12 Rc1/4 M22×135.9 23.9 12

9.5 23.3-

27 24 6-

1182

35.3 12.4 13 16.8 7 65

PMF12-03□ 12 Rc3/8 M22×138.9 18.4 15

10.5 23.3-

27 24 6-

1186

36.3 12.4 14 20.8 7 65

PMF12-04□ 12 Rc1/2 M22×141.9 18.4 18

13 23.3-

27 24 6-

1180

39.3 12.4 17 25 7 67

PMF16-03□ 16 Rc3/8 M27×1.5 38.317.9 15

10.5 24.8-

32 2910 -

14.2136

14.4 14 20.8 9 8.5 110

PMF16-04□ 16 Rc1/2 M27×1.541.3 17.9 18

13 24.8-

32 2910 - 13 136

40.8 14.4 16.5 25 9 8.5 15 110・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

øD

Rc

M

Hex.2

BE

2E

1T

1 CA

Hex.1øD

Rc

M

øP

BE

2E

1 T1

T2

CA

Hex.2

Hex.1

2014 NEW PRODUCTS

PMF Bulkhead Female Straight（mm - Rc）


17

Unit：㎜

Model codeTube O.D.

øDRc M B E1 E2 A C øP Hex.1 Hex.2 T1 T2

Orifice（ø㎜）

Weight（g）

PMF4-N1U□ 4 1/8-27NPT 1/2-20UNF24.5 9.9 10

7 14.9-

9/16 9/16 5-

319

24.2 9 9 13.8 5 17

PMF6-N1U□ 6 1/8-27NPT 9/16-18UNF27.1 11.9

10 7 17-

11/16 11/16 5.5- 4.6 32

26.4 10.2 13.8 6 5 28

PMF6-N2U□ 6 1/4-18NPT 9/16-18UNF30.1 11.9 13

9.5 17-

11/16 11/16 5.5- 4.6 32

28.7 10.2 12.3 17.2 6 5 29

PMF8-N2U□ 8 1/4-18NPT 5/8-18UNF32 13.5

13 9.5 18.2-

3/4 3/4 5.5- 6 41

30 9.8 16.8 6 7 33

PMF8-N3U□ 8 3/8-18NPT 5/8-18UNF33 13.5

14 10.5 18.2-

3/4 3/4 5.5- 6 35

31 9.8 19.5 6 7 31

PMF10-N3U□ 10 3/8-18NPT 7/8-14UNF35.8 14.9 15

10.5 20.7-

1 1 7- 8.5 88

33.7 11.1 14 20.8 7 9 67

PMF12-N3U□ 12 3/8-18NPT 7/8-14UNF38.9 18.4 15

10.5 23.3-

1 1 7-

1188

36.3 12.4 14 20.8 7 68

PMF5/32-N1U□ 5/32 1/8-27NPT 1/2-20UNF24.5 9.9 10

7 14.9-

9/16 9/16 5-

319

24.2 9 9 13.8 5 17

PMF5/32-N2U□ 5/32 1/4-18NPT 1/2-20UNF 27.59.9 13

9.5 14.9-

9/16 11/16 5-

326

9 12.3 17.2 6 24

PMF3/16-N1U□ 3/16 1/8-27NPT 9/16-18UNF27.5 11.9

10 7 17.4-

11/16 11/16 5.5-

432

26.8 10.2 13.8 6 28

PMF3/16-N2U□ 3/16 1/4-18NPT 9/16-18UNF30.5 11.9 13

9.5 17.4-

11/16 11/16 5.5-

432

29.1 10.2 12.3 17.2 6 30

PMF1/4-N1U□ 1/4 1/8-27NPT 9/16-18UNF27.1 11.9

10 7 17-

11/16 11/16 5.5- 4.6 32

26.4 10.2 13.8 6 5.3 28

PMF1/4-N2U□ 1/4 1/4-18NPT 9/16-18UNF30.1 11.9 13

9.5 17-

11/16 11/16 5.5- 4.6 32

28.7 10.2 12.3 17.2 6 5.3 29

PMF1/4-N3U□ 1/4 3/8-18NPT 9/16-18UNF31.1 11.9

14 10.5 17-

11/16 3/4 5.5- 4.6 31

30.4 10.2 19.5 6 5.3 30

PMF5/16-N1U□ 5/16 1/8-27NPT 5/8-18UNF29 13.5

10 7 18.2-

3/4 3/4 5.5- 6 40

27 9.8 13.8 6 7 31

PMF5/16-N2U□ 5/16 1/4-18NPT 5/8-18UNF32 13.5

13 9.5 18.2-

3/4 3/4 5.5- 6 41

30 9.8 16.8 6 7 33

PMF5/16-N3U□ 5/16 3/8-18NPT 5/8-18UNF33 13.5

14 10.5 18.2-

3/4 3/4 5.5- 6 35

31 9.8 19.5 6 7 31

PMF3/8-N1U□ 3/8 1/8-27NPT 7/8-14UNF30.8 14.9

10 7 20.7-

1 1 7- 7.5 81

29.7 11.1 13.8 7 8.3 66

PMF3/8-N2U□ 3/8 1/4-18NPT 7/8-14UNF34.8 14.9 14

9.5 20.7-

1 1 7-

8.593

32.7 11.1 13 16.8 7 67

PMF3/8-N3U□ 3/8 3/8-18NPT 7/8-14UNF35.8 14.9 15

10.5 20.7-

1 1 7-

8.590

33.7 11.1 14 20.8 7 68

PMF1/2-N2U□ 1/2 1/4-18NPT 7/8-14UNF35.7 18.4 12

9.5 23.1-

1 1 7-

1183

35.1 12.4 13 16.8 7 65

PMF1/2-N3U□ 1/2 3/8-18NPT 7/8-14UNF38.7 18.4 15

10.5 23.1-

1 1 7-

1187

36.1 12.4 14 20.8 7 66

PMF1/2-N4U□ 1/2 1/2-14NPT 7/8-14UNF41.7 18.4 18

13 23.1-

1 1 7-

1183

39.1 12.4 17 25.2 7 70・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*The prices remain the same with current models.

øD

Rc

M

Hex.2

BE

2E

1T

1 CA

Hex.1øD

Rc

M

øP

BE

2E

1 T1

T2

CA

Hex.2

Hex.1


PMF Bulkhead Female Straight（mm - NPT & inch - NPT）


18

Unit：㎜

Model codeTube O.D.

øDR A B L øP C E Hex.

Orifice (ø㎜ )

Weight (g)

PL4-M5□ 4 M5×0.83［3.2］ 20.3 22.3［22.1］

10 14.918 10 1.8 8

3 16 18 17.7 8 2.4 5.7

PL4-M6□ 4 M6×1 421.3 22.3

10 14.918

10 2.48.3

20 21 18.7 8.0

PL4-01□ 4 R1/8 823.3 24.3

10 14.918

10 2.811

22 23 18.7 10

PL4-02□ 4 R1/4 1126.3 25.3

10 14.918

14 2.821

29 28 20.7 18

PL6-M5□ 6 M5×0.83［3.2］ 22 25.3［25.1］

12.516.8 19.8 12 1.8 13

3 19.5 22.8 17 20.3 10 2.4 8.9

PL6-M6□ 6 M6×1 423 25.3

12.516.8 19.8 12

313

20.5 22.8 17 20.3 10 8.0

PL6-01□ 6 R1/8 825 27.3

12.516.8 19.8 12

4.314

22.5 24.8 17 20.3 10 11

PL6-02□ 6 R1/4 11 28 28.2 12.516.8 19.8

14 4.322

17 21.8 19

PL6-03□ 6 R3/8 1229.8

29.7 12.516.8 19.8

17 4.335

31.5 17 23.8 30

PL8-01□ 8 R1/8 828 31.3

14.5 18.1 22.714

619

24 27.3 12 14

PL8-02□ 8 R1/4 1131 32.2

14.5 18.122.7

146 24

28 29.2 23.7 6.7 20

PL8-03□ 8 R3/8 1232.8 33.7

14.5 18.122.7

176 37

31 31.9 24.7 6.7 31

PL10-01□ 10 R1/8 833 37.8

17.5 20.226.2 17

631

25 29.8 25.5 12 18

PL10-02□ 10 R1/4 1136 38.7

17.5 20.226.2 17

834

28.5 31.2 26 14 23

PL10-03□ 10 R3/8 1237 39.4

17.5 20.226.2

178 43

32 34.4 27 8.3 34

PL10-04□ 10 R1/2 1540 40.6

17.5 20.226.2

218 65

36 36.6 27.5 8.3 57

PL12-02□ 12 R1/4 1138 42.5

21 23.429.4 21

851

29.8 34.2 29 14 27

PL12-03□ 12 R3/8 1239 43.2

21 23.429.4 21

1052

32.5 36.7 29.7 17 38

PL12-04□ 12 R1/2 1542 44.3

21 23.429.4

2110 67

36.5 38.8 30.7 10.3 61・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type

øD

RHex.

øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

R

2014 NEW PRODUCTS

PL Elbow（mm - R）


19

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PL5/32-M5□ 5/32 M5×0.83［3.2］ 20.3 22.3［22.1］

10 14.918 10 1.8 8

3 16 18 17.7 8 2.4 5.7

PL5/32-01□ 5/32 R1/8 823.3 24.3

10 14.918

10 2.811

22 23 18.7 10

PL5/32-02□ 5/32 R1/4 1126.3 25.3

10 14.918

14 2.821

29 28 20.7 18

PL3/16-M5□ 3/16 M5×0.83［3.2］ 22 25.3［25.1］

12.517.2 20.2 12 1.8 12

3 19.5 22.8 17.4 20.7 10 2.4 8.7

PL3/16-01□ 3/16 R1/8 825 27.3

12.517.2 20.2 12

3.314

22.5 24.8 17.4 20.7 10 11

PL3/16-02□ 3/16 R1/4 11 28 28.2 12.517.2 20.2

14 3.322

17.4 22.2 19

PL1/4-M5□ 1/4 M5×0.83［3.2］ 22 25.3［25.1］

12.516.8 19.8 12 1.8 12

3 19.5 22.8 17 20.3 10 2.4 8.5

PL1/4-01□ 1/4 R1/8 825 27.3

12.516.8 19.8 12

4.614

22.5 24.8 17 20.3 10 11

PL1/4-02□ 1/4 R1/4 11 28 28.2 12.516.8 19.8

144.6 22

17 21.8 5.3 18

PL1/4-03□ 1/4 R3/8 1229.8 29.7

12.516.8 19.8

174.6 35

31.5 31.4 17 23.8 5.3 29

PL5/16-01□ 5/16 R1/8 828 31.3

14.5 18.1 22.714

619

24 27.3 12 14

PL5/16-02□ 5/16 R1/4 1131 32.2

14.5 18.122.7

146 24

28 29.2 23.7 6.7 20

PL5/16-03□ 5/16 R3/8 1232.8 33.7

14.5 18.122.7

176 37

31 31.9 24.7 6.7 31

PL3/8-01□ 3/8 R1/8 833 37.8

17.5 20.226.2 17

631

25 29.8 25.5 12 18

PL3/8-02□ 3/8 R1/4 1136 38.7

17.5 20.226.2 17

834

28.5 31.2 26 14 24

PL3/8-03□ 3/8 R3/8 1237 39.4

17.5 20.226.2

178 43

32 34.4 27 8.3 35

PL3/8-04□ 3/8 R1/2 1540 40.6

17.5 20.226.2

218 65

36 36.6 27.5 8.3 58

PL1/2-02□ 1/2 R1/4 1138 42.5

21 23.729.7 21

850

29.8 34.2 29.3 14 26

PL1/2-03□ 1/2 R3/8 1239 43.2

21 23.729.7 21

1051

32.5 36.7 30 17 37

PL1/2-04□ 1/2 R1/2 1542 44.3

21 23.729.7

2110 67

36.5 38.8 31 11 60・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread typeø

D

RHex.

øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

R


PL Elbow（inch - R）


20

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PL4-U10U□ 4 No.10-32UNF 320.3 22.3

10 14.918 7/16 1.8 8.1

16 18 17.7 5/16 2.4 5.4

PL4-N0U□ 4 1/16-27NPT 823.3 24.2

10 14.918

7/16 2.8 9.9

22 22.9 18.7 12

PL4-N1U□ 4 1/8-27NPT 823.3 24.2

10 14.918

7/16 2.8 12

22 22.9 18.7 11

PL4-N2U□ 4 1/4-18NPT 1126.3 25.5

10 14.918

9/16 2.8 22

29 28.2 20.7 18

PL6-U10U□ 6 No.10-32UNF 322 25.3

12.516.8 19.8 1/2 1.8 13

19.5 22.8 17 20.3 7/16 2.4 9.1

PL6-N0U□ 6 1/16-27NPT 825 27.2

12.516.8 19.8 1/2 4.6 13

22.5 24.7 17 20.3 7/16 4.3 13

PL6-N1U□ 6 1/8-27NPT 825 27.1

12.516.8 19.8 1/2 4.6 15

22.5 24.6 17 20.3 7/16 4.3 12

PL6-N2U□ 6 1/4-18NPT 1128 28.5

12.516.8 19.8

9/164.6 21

28 28.5 17 21.8 4.3 19

PL6-N3U□ 6 3/8-18NPT 1229.8 30

12.516.8 19.8

11/164.6 36

31.5 31.7 17 23.8 4.3 31

PL8-N1U□ 8 1/8-27NPT 828 31.1

14.5 18.1 22.79/16

6.0 20

24 27.1 1/2 15

PL8-N2U□ 8 1/4-18NPT 1131 32.5

14.5 18.122.7

9/166.0 24

28 29.5 23.7 6.7 20

PL8-N3U□ 8 3/8-18NPT 1232.8 34

14.5 18.122.7

11/166.0 38

31 32.2 24.7 6.7 32

PL10-N1U□ 10 1/8-27NPT 833 37.6

17.5 20.226.2 11/16

6.0 32

25 26.9 25.5 1/2 19

PL10-N2U□ 10 1/4-18NPT 1136 39

17.5 20.226.2 11/16

8.0 35

28.5 31.5 26 9/16 24

PL10-N3U□ 10 3/8-18NPT 1237 39.7

17.5 20.226.2

11/168.0 43

32 34.7 27 8.3 36

PL10-N4U□ 10 1/2-14NPT 1540 40.6

17.5 20.226.2

7/88.0 65

36 36.6 27.5 8.3 60

PL12-N2U□ 12 1/4-18NPT 1138 42.7

21 23.429.4 7/8

8.0 52

29.8 34.5 29.3 9/16 27

PL12-N3U□ 12 3/8-18NPT 1239 43.4

21 23.429.4 7/8

10.0 53

32.5 36.9 30 11/16 39

PL12-N4U□ 12 1/2-14NPT 1542 44.4

21 23.429.4

7/810.0 68

36.5 38.9 31 10.3 63・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.


DRHex.

øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

RUnified Unified

2014 NEW PRODUCTS

PL Elbow（mm - NPT）


21

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PL5/32-U10U□ 5/32 No.10-32UNF 320.3 22.3

10 14.918 7/16 1.8 8.3

16 18 17.7 5/16 2.4 5.4

PL5/32-N0U□ 5/32 1/16-27NPT 823.3 24.2

10 14.918

7/16 2.8 9.9

22 22.9 18.7 12

PL5/32-N1U□ 5/32 1/8-27NPT 823.3 24.2

10 14.918

7/16 2.8 12

22 22.9 18.7 11

PL5/32-N2U□ 5/32 1/4-18NPT 1126.3 25.5

10 14.918

9/16 2.8 21

29 28.2 20.7 18

PL3/16-U10U□ 3/16 No.10-32UNF 322 25.3

12.517.2 20.2 1/2 1.8 13

19.5 22.8 17.4 20.7 7/16 2.4 9.4

PL3/16-N0U□ 3/16 1/16-27NPT 825 27.2

12.517.2 20.2 1/2 3.9 13

22.5 24.7 17.4 20.7 7/16 3.3 14

PL3/16-N1U□ 3/16 1/8-27NPT 825 27.1

12.517.2 20.2 1/2 3.9 15

22.5 24.6 17.4 20.7 7/16 3.3 12

PL3/16-N2U□ 3/16 1/4-18NPT 1128 28.5

12.517.2 20.2

9/163.9 23

28 28.5 17.4 22.2 3.3 19

PL1/4-U10U□ 1/4 No.10-32UNF 322 25.3

12.516.8 19.8 1/2 1.8 13

19.5 22.8 17 20.3 7/16 2.4 9

PL1/4-N0U□ 1/4 1/16-27NPT 825 27.2

12.516.8 19.8 1/2

4.6 13

22.5 24.7 17 20.3 7/16 13

PL1/4-N1U□ 1/4 1/8-27NPT 825 27.1

12.516.8 19.8 1/2

4.6 15

22.5 24.6 17 20.3 7/16 12

PL1/4-N2U□ 1/4 1/4-18NPT 1128 28.5

12.516.8 19.8

9/164.6 22

28 28.5 17 21.8 5.3 19

PL1/4-N3U□ 1/4 3/8-18NPT 1229.8 30

12.516.8 19.8

11/164.6 36

31.5 31.7 17 23.8 5.3 31

PL5/16-N1U□ 5/16 1/8-27NPT 828 31.1

14.5 18.1 22.79/16

6.0 19

24 27.1 1/2 15

PL5/16-N2U□ 5/16 1/4-18NPT 1131 32.5

14.5 18.122.7

9/166.0 24

28 29.5 23.7 6.7 20

PL5/16-N3U□ 5/16 3/8-18NPT 1232.8 34

14.5 18.122.7

11/166.0 38

31 32.2 24.7 6.7 32

PL3/8-N1U□ 3/8 1/8-27NPT 833 37.6

17.5 20.226.2 11/16

6.0 32

25 29.6 25.5 1/2 19

PL3/8-N2U□ 3/8 1/4-18NPT 1136 39

17.5 20.226.2 11/16

8.0 34

28.5 31.5 26 9/16 24

PL3/8-N3U□ 3/8 3/8-18NPT 1237 39.7

17.5 20.226.2

11/168.0 43

32 34.7 27 8.3 36

PL3/8-N4U□ 3/8 1/2-14NPT 1540 40.6

17.5 20.226.2

7/88.0 65

36 36.6 27.5 8.3 60

PL1/2-N2U□ 1/2 1/4-18NPT 1138 42.7

21 23.729.7 7/8

8.0 51

29.8 34.5 29.3 9/16 26

PL1/2-N3U□ 1/2 3/8-18NPT 1239 43.4

21 23.729.7 7/8

10.0 52

32.5 36.9 30 11/16 38

PL1/2-N4U□ 1/2 1/2-14NPT 1542 44.4

21 23.729.7

7/810.0 67

36.5 38.9 31 11.0 63・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.　*The prices remain the same with current models.


D

RHex.

øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

RUnified Unified


PL Elbow（inch - NPT）


22

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PLL4-M5□ 4 M5×0.83［3.2］ 32.3 34.3［34.1］

10 14.918 10 1.8 8.4

3 28 30 18.7 8 2.4 6.4

PLL4-01□ 4 R1/8 835.3 36.3

10 14.918

10 2.817

34 35 18.7 11

PLL4-02□ 4 R1/4 1138.3 37.3

10 14.918

14 2.834

41 40 20.7 19

PLL6-M5□ 6 M5×0.83［3.2］ 35 38.3［38.1］

12.516.8 19.8 12 1.8 24

3 34 37.3 17 20.3 10 2.4 9.9

PLL6-01□ 6 R1/8 838 40.3

12.516.8 19.8 12

4.326

37 39.3 17 20.3 10 13

PLL6-02□ 6 R1/4 1141 41.2

12.516.8 19.8

14 4.339

42.5 42.7 17 21.8 20

PLL6-03□ 6 R3/8 1243.3 43.2

12.516.8 19.8

17 4.362

46 45.9 17 23.8 33

PLL8-01□ 8 R1/8 843.5 46.8

14.5 18.1 22.714

637

40.5 43.8 12 16

PLL8-02□ 8 R1/4 1146.5 47.7

14.5 18.122.7

146 43

44.5 45.7 23.7 6.7 22

PLL8-03□ 8 R3/8 1248.3 49.2

14.5 18.122.7

176 66

47.5 48.4 24.7 6.7 35

PLL10-01□ 10 R1/8 851.5 56.3

17.5 20.226.2 17

662

44.5 49.3 25.5 12 20

PLL10-02□ 10 R1/4 1154.5 57.2

17.5 20.226.2 17

865

48 50.7 26 14 26

PLL10-03□ 10 R3/8 1255.5 57.9

17.5 20.226.2

178 74

51.5 53.9 27 8.3 38

PLL10-04□ 10 R1/2 1560 60.6

17.5 20.226.2

218 121

55.5 56.1 27 8.3 63

PLL12-02□ 12 R1/4 1160 64.5

21 23.429.4 21

8112

52.8 57.2 29 14 30

PLL12-03□ 12 R3/8 1261 65.2

21 23.429.4 21

10107

55.5 59.7 29.7 17 42

PLL12-04□ 12 R1/2 1564 66.3

21 23.429.4

2110 123

59.5 61.8 29.7 10.3 68・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type

øD

R

Hex.

øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

R

2014 NEW PRODUCTS

PLL Long Elbow（mm - R）


23

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PLL5/32-01□ 5/32 R1/8 835.3 36.3

10 14.918

10 2.817

34 35 18.7 11

PLL5/32-02□ 5/32 R1/4 1138.3 37.3

10 14.918

14 2.834

41 40 20.7 19

PLL3/16-01□ 3/16 R1/8 838 40.3

12.517.2 20.2 12

3.326

37 39.3 17.4 20.7 10 13

PLL3/16-02□ 3/16 R1/4 1141 41.2

12.517.2 20.2

14 3.339

42.5 42.7 17.4 22.2 21

PLL1/4-01□ 1/4 R1/8 838 40.3

12.516.8 19.8 12

4.626

37 39.3 17 20.3 10 13

PLL1/4-02□ 1/4 R1/4 1141 41.2

12.516.8 19.8

144.6 39

42.5 42.7 17 21.8 5.3 20

PLL1/4-03□ 1/4 R3/8 1243.3 43.2

12.516.8 19.8

174.6 61

46 45.9 17 23.8 5.3 33

PLL5/16-01□ 5/16 R1/8 843.5 46.8

14.5 18.1 22.714

637

40.5 43.8 12 16

PLL5/16-02□ 5/16 R1/4 1146.5 47.7

14.5 18.122.7

146 43

44.5 45.7 23.7 6.7 22

PLL5/16-03□ 5/16 R3/8 1248.3 49.2

14.5 18.122.7

176 66

47.5 48.4 24.7 6.7 35

PLL3/8-01□ 3/8 R1/8 851.5 56.3

17.5 20.226.2 17

662

44.5 49.3 25.5 12 20

PLL3/8-02□ 3/8 R1/4 1154.5 57.2

17.5 20.226.2 17

865

48 50.7 26 14 27

PLL3/8-03□ 3/8 R3/8 1255.5 57.9

17.5 20.226.2

178 74

51.5 53.9 27 8.3 39

PLL3/8-04□ 3/8 R1/2 1560 60.5

17.5 20.226.2

218 120

55.5 56.1 27 8.3 63

PLL1/2-02□ 1/2 R1/4 1160 64.5

21 23.729.7 21

8111

52.8 57.2 29.3 14 30

PLL1/2-03□ 1/2 R3/8 1261 65.2

21 23.729.7 21

10107

55.5 59.7 30 17 42

PLL1/2-04□ 1/2 R1/2 1564 66.3

21 23.729.7

2110 122

59.5 61.8 30 11 67・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

øD

R

Hex.

øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

R


PLL Long Elbow（inch - R）


24

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PLL5/32-U10U□ 5/32 No.10-32UNF 332.3 34.3

10 14.918 7/16 1.8 19

28 30 18.7 5/16 2.4 6.4

PLL5/32-N1U□ 5/32 1/8-27NPT 835.3 36.2

10 14.918

7/16 2.8 20

34 34.9 18.7 12

PLL5/32-N2U□ 5/32 1/4-18NPT 1138.3 37.5

10 14.918

9/16 2.8 35

41 40.2 20.7 20

PLL3/16-U10U□ 3/16 No.10-32UNF 335 38.3

12.517.2 20.2 1/2 1.8 27

34 37.3 17.4 20.7 7/16 2.4 11

PLL3/16-N1U□ 3/16 1/8-27NPT 838 40.1

12.517.2 20.2 1/2 3.9 29

37 39.1 17.4 20.7 7/16 3.3 14

PLL3/16-N2U□ 3/16 1/4-18NPT 1141 41.5

12.517.2 20.2

9/163.9 39

42.5 43 17.4 22.2 3.3 21

PLL1/4-U10U□ 1/4 No.10-32UNF 335 38.3

12.516.8 19.8 1/2 1.8 27

34 37.3 17 20.3 7/16 2.4 11

PLL1/4-N1U□ 1/4 1/8-27NPT 838 40.1

12.516.8 19.8 1/2

4.6 28

37 39.1 17 20.3 7/16 13

PLL1/4-N2U□ 1/4 1/4-18NPT 1141 41.5

12.516.8 19.8

9/164.6 39

42.5 43 17 21.8 5.3 21

PLL1/4-N3U□ 1/4 3/8-18NPT 1243.3 43.5

12.516.8 19.8

11/164.6 64

46 46.2 17 23.8 5.3 35

PLL5/16-N1U□ 5/16 1/8-27NPT 843.5 46.6

14.5 18.1 22.79/16

6.0 37

40.5 43.6 1/2 17

PLL5/16-N2U□ 5/16 1/4-18NPT 1146.5 48

14.5 18.122.7

9/166.0 43

44.5 46 23.7 6.7 23

PLL5/16-N3U□ 5/16 3/8-18NPT 1248.3 49.5

14.5 18.122.7

11/166.0 69

47.5 48.7 24.7 6.7 36

PLL3/8-N1U□ 3/8 1/8-27NPT 851.5 56.1

17.5 20.226.2 11/16

6.0 66

44.5 49.1 25.5 1/2 21

PLL3/8-N2U□ 3/8 1/4-18NPT 1154.5 57.5

17.5 20.226.2 11/16

8.0 68

48 51 26 9/16 27

PLL3/8-N3U□ 3/8 3/8-18NPT 1255.5 58.2

17.5 20.226.2

11/168.0 76

51.5 54.2 27 8.3 40

PLL3/8-N4U□ 3/8 1/2-14NPT 1560 60.6

17.5 20.226.2

7/88.0 129

55.5 56.1 27 8.3 66

PLL1/2-N2U□ 1/2 1/4-18NPT 1160 64.7

21 23.729.7 7/8

8.0 120

52.8 57.5 29.3 9/16 30

PLL1/2-N3U□ 1/2 3/8-18NPT 1261 65.4

21 23.729.7 7/8

10.0 116

55.5 59.9 30 11/16 43

PLL1/2-N4U□ 1/2 1/2-14NPT 1564 66.4

21 23.729.7

7/810.0 131

59.5 61.9 30 11.0 70・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.


DR

Hex.øP

LB

CE

A ALB

RMetric thread type

øD

RHex.

øP

LB

CE

A

ALB

RUnified Unified

2014 NEW PRODUCTS

PLL Long Elbow（inch - NPT）


25

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PB4-M5□ 4 M5×0.83［3.2］ 20.2 22.2［22］

10 14.916.9 10 1.8 11

3 16 18 17.7 8 2.4 8

PB4-M6□ 4 M6×1 421.2 22.2

10 14.916.9

10 2.4 1120 21 18.7

PB4-01□ 4 R1/8 823.2 24.2

10 14.916.9

10 2.814

22 23 18.7 13

PB4-02□ 4 R1/4 1126.2 25.2

10 14.916.9

14 2.823

29 28 20.7 20

PB6-M5□ 6 M5×0.83［3.2］ 23 26.5［26.3］ 13

1720.15 12 1.8 16

3 19.5 22.8 12.5 20.25 10 2.4 12

PB6-M6□ 6 M6×1 424 26.5 13

1720.15 12

316

20.5 22.8 12.5 20.25 10 13

PB6-01□ 6 R1/8 826 28.5 13

1720.15 12

4.318

22.5 24.8 12.5 20.25 10 14

PB6-02□ 6 R1/4 1129 29.5 13

1720.15

14 4.326

28 28.2 12.5 21.75 22

PB6-03□ 6 R3/8 1230.8 31 13

1720.15

17 4.339

31.5 31.4 12.5 23.75 33

PB8-01□ 8 R1/8 826.3 29.8 15

18.122.4 14 5.8 23

24 27.3 14.5 22.7 12 6 19

PB8-02□ 8 R1/4 1129.3 30.8 15

18.122.4

145.8 29

28 29.2 14.5 23.7 6.7 25

PB8-03□ 8 R3/8 1231.1 32.3 15

18.122.4

175.8 42

31 31.9 14.5 24.7 6.7 35

PB10-01□ 10 R1/8 833 37.8

17.5 20.225.2 17

638

25 29.8 25.5 12 25

PB10-02□ 10 R1/4 1136 38.7

17.5 20.225.2 17

842

28.5 31.2 26 14 31

PB10-03□ 10 R3/8 1237 39.4

17.5 20.225.2

178 50

32 34.4 27 8.3 42

PB10-04□ 10 R1/2 1540 40.6

17.5 20.225.2

218 72

36 36.6 27.5 8.3 65

PB12-02□ 12 R1/4 1138 42.5

2122.9 28.4 21

861

29.8 34.2 23.4 28.95 14 38

PB12-03□ 12 R3/8 1239 43.2

2122.9 28.4 21

1062

32.5 36.7 23.4 29.7 17 48

PB12-04□ 12 R1/2 1542 44.3

2122.9 28.4

2110 78

36.5 38.8 23.4 30.7 10.3 72・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type

2-ø

D

RHex.

2-ø

P

LB

2-C2-E

A ALB

RMetric thread type

2-ø

D

R

Hex.

2-ø

P

LB

2-C2-E

A

ALB

R


PB Branch Tee（mm - R）


26

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PB5/32-01□ 5/32 R1/8 819.2 24.2

10 14.916.9

10 2.814

22 23 18.7 13

PB5/32-02□ 5/32 R1/4 1126.2 25.2

10 14.916.9

14 2.823

29 28 20.7 20

PB3/16-01□ 3/16 R1/8 826 28.5 13

17.420.55 12

3.318

22.5 24.8 12.5 20.65 10 15

PB3/16-02□ 3/16 R1/4 1129 29.5 13

17.420.55

14 3.325

28 28.2 12.5 22.15 22

PB1/4-01□ 1/4 R1/8 826 28.5 13

1720.15 12

4.618

22.5 24.8 12.5 20.25 10 14

PB1/4-02□ 1/4 R1/4 1129 29.5 13

1720.15

144.6 26

28 28.2 12.5 21.75 5.3 22

PB1/4-03□ 1/4 R3/8 1230.8 31 13

1720.15

174.6 39

31.5 31.4 12.5 23.75 5.3 33

PB5/16-01□ 5/16 R1/8 826.3 29.8 15

18.122.4 14 5.8 23

24 27.3 14.5 22.7 12 6 19

PB5/16-02□ 5/16 R1/4 1129.3 30.8 15

18.122.4

145.8 29

28 29.2 14.5 23.7 6.7 25

PB5/16-03□ 5/16 R3/8 1231.1 32.3 15

18.122.4

175.8 42

31 31.9 14.5 24.7 6.7 35

PB3/8-01□ 3/8 R1/8 833 37.8

17.5 20.225.2 17

639

25 29.8 25.5 12 25

PB3/8-02□ 3/8 R1/4 1136 38.7

17.5 20.225.2 17

842

28.5 31.2 26 14 31

PB3/8-03□ 3/8 R3/8 1237 39.4

17.5 20.225.2

178 50

32 34.4 27 8.3 42

PB3/8-04□ 3/8 R1/2 1540 40.6

17.5 20.225.2

218 72

36 36.6 27.5 8.3 65

PB1/2-02□ 1/2 R1/4 1138 42.5

2123.2 28.7 21

859

29.8 34.2 23.7 29.25 14 36

PB1/2-03□ 1/2 R3/8 1239 43.2

2123.2 28.7 21

1060

32.5 36.7 23.7 30 17 46

PB1/2-04□ 1/2 R1/2 1542 44.3

2123.2 28.7

2110 76

36.5 38.8 23.7 31 11 71・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

2-ø

D

R

Hex.

2-ø

P

LB

2-C2-E

A

ALB

R

Metric thread type

2-ø

D

RHex.

2-ø

P

LB

2-C2-E

A ALB

R

2014 NEW PRODUCTS

PB Branch Tee（inch - R）


27

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PB5/32-U10U□ 5/32 No.10-32UNF 320.2 22.2

10 14.916.9 7/16 1.8 11

16 18 17.7 5/16 2.4 7.9

PB5/32-N1U□ 5/32 1/8-27NPT 823.2 24.1

10 14.916.9

7/16 2.8 13

22 22.9 18.7 14

PB5/32-N2U□ 5/32 1/4-18NPT 1126.2 25.4

10 14.916.9

9/16 2.8 23

29 28.2 20.7 20

PB3/16-U10U□ 3/16 No.10-32UNF 323 26.5 13

17.420.55 1/2 1.8 17

19.5 22.8 12.5 20.65 7/16 2.4 13

PB3/16-N1U□ 3/16 1/8-27NPT 826 28.4 13

17.420.55 1/2 4.0 19

22.5 24.7 12.5 20.65 7/16 3.3 16

PB3/16-N2U□ 3/16 1/4-18NPT 1129 29.7 13

17.420.55

9/164.0 26

28 28.5 12.5 22.15 3.3 22

PB1/4-U10U□ 1/4 No.10-32UNF 323 26.5 13

1720.15 1/2 1.8 16

19.5 22.8 12.5 20.25 7/16 2.4 13

PB1/4-N1U□ 1/4 1/8-27NPT 826 28.4 13

1720.15 1/2 4.6 18

22.5 24.6 12.5 20.25 7/16 4.6 15

PB1/4-N2U□ 1/4 1/4-18NPT 1129 29.7 13

1720.15

9/164.6 26

28 28.5 12.5 21.75 5.3 22

PB1/4-N3U□ 1/4 3/8-18NPT 1230.8 31.2 13

1720.15

11/164.6 40

31.5 31.7 12.5 23.75 5.3 34

PB5/16-N1U□ 5/16 1/8-27NPT 826.3 29.7 15

18.122.4 9/16 5.8 23

24 27.2 14.5 22.7 1/2 6.0 20

PB5/16-N2U□ 5/16 1/4-18NPT 1129.3 31 15

18.122.4

9/165.8 29

28 29.5 14.5 23.7 6.7 25

PB5/16-N3U□ 5/16 3/8-18NPT 1231.1 32.5 15

18.122.4

11/165.8 43

31 32.2 14.5 24.7 6.7 37

PB3/8-N1U□ 3/8 1/8-27NPT 833 37.6

17.5 20.225.2 11/16

6.0 40

25 29.7 25.5 1/2 26

PB3/8-N2U□ 3/8 1/4-18NPT 1136 39

17.5 20.225.2 11/16

8.0 42

28.5 31.5 26 9/16 31

PB3/8-N3U□ 3/8 3/8-18NPT 1237 39.7

17.5 20.225.2

11/168.0 51

32 34.7 27 8.3 44

PB3/8-N4U□ 3/8 1/2-14NPT 1540 40.6

17.5 20.225.2

7/88.0 73

36 36.6 27.5 8.3 68

PB1/2-N2U□ 1/2 1/4-18NPT 1138 42.7

2123.2 28.7 7/8

8.0 61

29.8 34.5 23.7 29.25 9/16 36

PB1/2-N3U□ 1/2 3/8-18NPT 1239 43.4

2123.2 28.7 7/8

10.0 62

32.5 36.9 23.7 30 11/16 47

PB1/2-N4U□ 1/2 1/2-14NPT 1542 44.4

2123.2 28.7

7/810.0 77

36.5 38.9 23.7 31 11.0 73・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

2-ø

D

R

Hex.

2-ø

P

LB

2-C2-E

A

ALB

R

Metric thread type

2-ø

D

RHex.

2-ø

P

LB

2-C2-E

A ALB

RUnified Unified


PB Branch Tee（inch - NPT）


28

Unit：㎜

Model codeTube O.D.

øDR A B L1 L2 øP C E Hex.

Orifice (ø㎜ )

Weight (g)

PD4-M5□ 4 M5×0.83［3.2］ 37.1 34.1［33.9］ 17.2［17］

10 14.916.9 10 1.8 11

3 33.7 30.7 13.5 17.2 8 2.4 7.8

PD4-M6□ 4 M6×1 438.1 34.1 17.2

10 14.916.9

10 2.4 1138.2 34.2 17 17.2

PD4-01□ 4 R1/8 840.1 36.1 19.2

10 14.916.9

10 2.814

40.2 36.2 19 17.2 13

PD4-02□ 4 R1/4 1143.1 37.1 20.2

10 14.916.9

14 2.823

46.2 40.2 23 19.2 20

PD6-M5□ 6 M5×0.83［3.2］ 43.2 40.2［40］20［19.8］ 13

1720.1 12 1.8 16

3 40.3 37.3 16.8 12.5 20.5 10 2.4 12

PD6-M6□ 6 M6×1 444.2 40.2 20 13

1720.1 12

317

41.3 37.3 16.8 12.5 20.5 10 12

PD6-01□ 6 R1/8 846.2 42.2 22 13

1720.1 12

4.318

43.3 39.3 18.8 12.5 20.5 10 14

PD6-02□ 6 R1/4 1149.2 43.1 23 13

1720.1

14 4.326

48.8 42.7 22.2 12.5 20.5 22

PD6-03□ 6 R3/8 1251 44.6 24.5 13

1720.1

17 4.339

52 45.7 25.2 12.5 21.5 32

PD8-01□ 8 R1/8 850.4 46.4 24.2 15

18.122.2 14

623

46.9 42.9 20 14.5 22.9 12 19

PD8-02□ 8 R1/4 1153.4 47.4 25.2 15

18.122.2

146 29

51.7 45.7 22.8 14.5 22.9 6.7 25

PD8-03□ 8 R3/8 1255.2 48.9 26.7 15

18.122.2

176 42

55.4 49.1 26.2 14.5 22.9 6.7 35

PD10-01□ 10 R1/8 858.2 54.2 29

17.5 20.225.2 17

638

51.2 47.2 21 25.5 12 25

PD10-02□ 10 R1/4 1161.2 55.2 30

17.5 20.225.2 17

842

54.7 48.7 22.5 26.2 14 31

PD10-03□ 10 R3/8 1262.2 55.9 30.7

17.5 20.225.2

178 50

58.2 51.9 25.7 26.2 8.3 42

PD10-04□ 10 R1/2 1565.2 57 31.8

17.5 20.225.2

218 72

62.2 54 27.8 27.3 8.3 65

PD12-02□ 12 R1/4 1166.6 60.6 32.2

2122.9 28.2 21

862

60.3 54.2 23.7 23.4 30 14 38

PD12-03□ 12 R3/8 1267.6 61.3 32.9

2122.9 28.2 21

1078

63.5 57.2 26.7 23.4 30.5 17 48

PD12-04□ 12 R1/2 1570.6 62.4 34

2122.9 28.2

2110 78

67.5 59.3 28.8 23.4 30.7 10.3 72・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type

2-ø

D

RHex.

2-øP

L1B

2-C

L2

2-E

A ALB

RMetric thread type

2-ø

D

RHex.

2-øP

L1B

2-C

L2

2-E

A

ALB

R

2014 NEW PRODUCTS

PD Run Tee（mm - R）


29

Unit：㎜

Mod el codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PD5/32-01□ 5/32 R1/8 840.1 36.1 19.2

10 14.916.9

10 2.814

40.2 36.2 19 17.2 13

PD5/32-02□ 5/32 R1/4 1143.1 37.1 20.2

10 14.916.9

14 2.823

46.2 40.2 23 19.2 20

PD3/16-01□ 3/16 R1/8 846.6 42.6 22 13

17.420.5 12

3.318

43.7 39.7 18.8 12.5 20.9 10 15

PD3/16-02□ 3/16 R1/4 1149.6 43.5 23 13

17.420.5

14 3.326

49.2 43.1 22.2 12.5 20.9 22

PD1/4-01□ 1/4 R1/8 846.2 42.2 22 13

1720.1 12

4.618

43.3 39.3 18.8 12.5 20.5 10 14

PD1/4-02□ 1/4 R1/4 1149.2 43.1 23 13

1720.1

144.6 26

48.8 42.7 22.2 12.5 20.5 5.3 22

PD1/4-03□ 1/4 R3/8 1251 44.6 24.5 13

1720.1

174.6 39

52 45.7 25.2 12.5 21.5 5.3 32

PD5/16-01□ 5/16 R1/8 850.4 46.4 24.2 15

18.122.2 14

623

46.9 42.9 20 14.5 22.9 12 19

PD5/16-02□ 5/16 R1/4 1153.4 47.4 25.2 15

18.122.2

146 29

51.7 45.7 22.8 14.5 22.9 6.7 25

PD5/16-03□ 5/16 R3/8 1255.2 48.9 26.7 15

18.122.2

176 42

55.4 49.1 26.2 14.5 22.9 6.7 35

PD3/8-01□ 3/8 R1/8 858.2 54.2 29

17.5 20.225.2 17

639

51.2 47.2 21 25.5 12 25

PD3/8-02□ 3/8 R1/4 1161.2 55.2 30

17.5 20.225.2 17

842

54.7 48.7 22.5 26.2 14 31

PD3/8-03□ 3/8 R3/8 1262.2 55.9 30.7

17.5 20.225.2

178 50

58.2 51.9 25.7 26.2 8.3 42

PD3/8-04□ 3/8 R1/2 1565.2 57 31.8

17.5 20.225.2

218 72

62.2 54 27.8 27.3 8.3 65

PD1/2-02□ 1/2 R1/4 1166.9 60.9 32.2

2123.2 28.5 21

859

60.6 54.5 23.7 23.7 30.3 14 37

PD1/2-03□ 1/2 R3/8 1267.9 61.6 32.9

2123.2 28.5 21

1060

63.8 57.5 26.7 23.7 30.8 17 47

PD1/2-04□ 1/2 R1/2 1570.9 62.7 34

2123.2 28.5

2110 76

67.8 59.6 28.8 23.7 31 11 71・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

2-ø

D

RHex.

2-øP

L1B

2-C

L2

2-E

A ALB

RMetric thread type

2-ø

D

RHex.

2-øP

L1B

2-C

L2

2-E

A

ALB

R


PD Run Tee（inch - R）


30

Unit：㎜

Mod el codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PD5/32-U10U□ 5/32 No.10-32UNF 337.1 34.1 17.2

10 14.916.9 7/16 1.8 11

33.7 30.7 13.5 17.2 5/16 2.4 7.8

PD5/32-N1U□ 5/32 1/8-27NPT 840.1 36 19.1

10 14.916.9

7/16 2.8 1440.2 36.1 18.9 17.2

PD5/32-N2U□ 5/32 1/4-18NPT 1143.1 37.3 20.4

10 14.916.9

9/16 2.8 23

46.2 40.4 23.2 19.2 20

PD3/16-U10U□ 3/16 No.10-32UNF 343.6 40.6 20 13

17.420.5 1/2 1.8 17

40.7 37.7 16.8 12.5 20.9 7/16 2.4 13

PD3/16-N1U□ 3/16 1/8-27NPT 846.6 42.4 21.9 13

17.420.5 1/2 4.0 19

43.7 39.5 18.6 12.5 20.9 7/16 3.3 16

PD3/16-N2U□ 3/16 1/4-18NPT 1149.6 43.8 23.2 13

17.420.5

9/164.0 27

49.2 43.4 22.5 12.5 20.9 3.3 22

PD1/4-U10U□ 1/4 No.10-32UNF 343.2 40.2 20 13

1720.1 1/2 1.8 16

40.3 37.3 16.8 12.5 20.5 7/16 2.4 13

PD1/4-N1U□ 1/4 1/8-27NPT 846.2 42 21.9 13

1720.1 1/2

4.6 18

43.3 39.1 18.6 12.5 20.5 7/16 15

PD1/4-N2U□ 1/4 1/4-18NPT 1149.2 43.4 23.2 13

1720.1

9/164.6 26

48.8 43 22.5 12.5 20.5 5.3 22

PD1/4-N3U□ 1/4 3/8-18NPT 1251 44.9 24.7 13

1720.1

11/164.6 40

52 45.9 25.4 12.5 21.5 5.3 34

PD5/16-N1U□ 5/16 1/8-27NPT 850.4 46.3 24.1 15

18.122.2 9/16

6.0 23

46.9 42.8 19.9 14.5 22.9 1/2 20

PD5/16-N2U□ 5/16 1/4-18NPT 1153.4 47.6 25.4 15

18.122.2

9/166.0 29

51.7 45.9 23 14.5 22.9 6.7 25

PD5/16-N3U□ 5/16 3/8-18NPT 1255.2 49.1 26.9 15

18.122.2

11/166.0 43

55.4 49.3 26.4 14.5 22.9 6.7 37

PD3/8-N1U□ 3/8 1/8-27NPT 858.2 54.1 28.9

17.5 20.225.2 11/16

6.0 40

51.2 47.1 20.9 25.5 1/2 26

PD3/8-N2U□ 3/8 1/4-18NPT 1161.2 55.4 30.2

17.5 20.225.2 11/16

8.0 42

54.7 48.9 22.7 26.2 9/16 31

PD3/8-N3U□ 3/8 3/8-18NPT 1262.2 56.1 30.9

17.5 20.225.2

11/168.0 51

58.2 52.1 25.9 26.2 8.3 43

PD3/8-N4U□ 3/8 1/2-14NPT 1565.2 57.1 31.9

17.5 20.225.2

7/88.0 73

62.2 54.1 27.9 27.3 8.3 67

PD1/2-N2U□ 1/2 1/4-18NPT 1166.9 61.1 32.4

2123.2 28.5 7/8

8.0 61

60.6 54.8 24 23.7 30.3 9/16 37

PD1/2-N3U□ 1/2 3/8-18NPT 1267.9 61.8 33.1

2123.2 28.5 7/8

10.0 62

63.8 57.7 26.9 23.7 30.8 11/16 48

PD1/2-N4U□ 1/2 1/2-14NPT 1570.9 62.8 34.1

2123.2 28.5

7/810.0 77

67.8 59.7 28.9 23.7 31 11.0 73・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

2-ø

DRHex.

2-øP

L1B

2-C

L22-E

A ALB

RMetric thread type

2-ø

D

RHex.

2-øP

L1B

2-C

L2

2-E

A

ALB

RUnified Unified

2014 NEW PRODUCTS

PD Run Tee（inch - NPT）


31

Unit：㎜

Model codeTube O.D.

øDR A B L øP C J ød F T Hex.

Orifice (ø㎜ )

Weight (g)

PX4-M5□ 4 M5×0.83［3.2］ 37.6 34.6［34.4］

10 14.911 3.2 14.1 10.4 10 1.8 11

3 32.9 29.9 10.3 - - - 8 2.4 8

PX4-M6□ 4 M6×1 438.6 34.6

10 14.911 3.2 14.1 10.4

10 2.4 1136.4 32.4 10.3 - - -

PX4-01□ 4 R1/8 840.6 36.6

10 14.911 3.2 14.1 10.4

102.7 14

38.4 34.4 10.3 - - - 2.8 13

PX4-02□ 4 R1/4 1143.6 37.6

10 14.911 3.2 14.1 10.4

142.7 23

43.4 37.4 10.3 - - - 2.8 20

PX6-M5□ 6 M5×0.83［3.2］ 41.4 38.4［38.2］

12.5 1712 3.4 15.8 13.5 12 1.8 16

3 38.3 35.3 12.5 - - - 10 2.4 13

PX6-M6□ 6 M6×1 442.4 38.4

12.5 1712 3.4 15.8 13.5 12

317

39.3 35.3 12.5 - - - 10 13

PX6-01□ 6 R1/8 844.4 40.4

12.5 1712 3.4 15.8 13.5 12

4.318

41.3 37.3 12.5 - - - 10 15

PX6-02□ 6 R1/4 1147.4 41.3

12.5 1712 3.4 15.8 13.5

14 4.326

48.3 42.2 12.5 - - - 22

PX6-03□ 6 R3/8 1249.2 42.8

12.5 1712 3.4 15.8 13.5

17 4.340

51.3 44.9 12.5 - - - 33

PX8-01□ 8 R1/8 848.7 44.7

14.5 18.114 3.4 17.2 15.1 14 5.9 24

46.1 42.1 14.5 - - - 12 6 20

PX8-02□ 8 R1/4 1151.7 45.7

14.5 18.114 3.4 17.2 15.1

145.9 29

49.3 43.3 14.5 - - - 6.7 25

PX8-03□ 8 R3/8 1253.5 47.2

14.5 18.114 3.4 17.2 15.1

175.9 43

52.5 46.2 14.5 - - - 6.7 36

PX10-01□ 10 R1/8 855.3 51.3 18 20.7 18 4.5 19.5 18 17

640

49.8 45.8 17.5 20.2 17.5 - - - 12 27

PX10-02□ 10 R1/4 1158.3 52.3 18 20.7 18 4.5 19.5 18 17 6.7 4453.6 47.6 17.5 20.2 17.5 - - - 14 8 32

PX10-03□ 10 R3/8 1259.3 53 18 20.7 18 4.5 19.5 18

176.7 52

56.7 50.4 17.5 20.2 17.5 - - - 8.3 43

PX10-04□ 10 R1/2 1562.3 54.1 18 20.7 18 4.5 19.5 18

216.7 74

60.2 52 17.5 20.2 17.5 - - - 8.3 66

PX12-02□ 12 R1/4 1163.5 57.5

21 23.420 4.2 22.2 21 21

864

58.6 52.6 21 - - - 14 40

PX12-03□ 12 R3/8 1264.5 58.2

21 23.420 4.2 22.2 21 21 8 65

60.6 54.3 21 - - - 17 10 51

PX12-04□ 12 R1/2 1567.5 59.3

21 23.420 4.2 22.2 21

218 81

64.7 56.5 21 - - - 10.3 74・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The dimensions in [ ] are those of clean-room package spec.*The prices remain the same with current models.

Metric thread type

RHex.

LB

2-C

J2-øD

A

ALB

2-øP

RMetric thread type

2-øP

R

Hex.

TLB

2-C F

J2-øD

ød

A ALB

R


PX Branch Y（mm - R）


32

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PX5/32-01□ 5/32 R1/8 840.6 36.6

10 14.911 3.2 14.1 10.4

102.7 14

38.4 34.4 10.3 - - - 2.8 13

PX5/32-02□ 5/32 R1/4 1143.6 37.6

10 14.911 3.2 14.1 10.4

142.7 23

43.4 37.4 10.3 - - - 2.8 20

PX3/16-01□ 3/16 R1/8 844.8 40.8

12.5 17.412 3.4 16.2 13.5 12

3.318

41.7 37.7 12.5 - - - 10 15

PX3/16-02□ 3/16 R1/4 1147.8 41.7

12.5 17.412 3.4 16.2 13.5

14 3.326

48.7 42.6 12.5 - - - 23

PX1/4-01□ 1/4 R1/8 844.4 40.4

12.5 1712 3.4 15.8 13.5 12 4.4 18

41.3 37.3 12.5 - - - 10 4.6 15

PX1/4-02□ 1/4 R1/4 1147.4 41.3

12.5 1712 3.4 15.8 13.5

144.4 26

48.3 42.2 12.5 - - - 5.3 22

PX1/4-03□ 1/4 R3/8 1249.2 42.8

12.5 1712 3.4 15.8 13.5

174.4 39

51.3 44.9 12.5 - - - 5.3 33

PX5/16-01□ 5/16 R1/8 848.7 44.7

14.5 18.114 3.4 17.2 15.1 14 5.9 24

46.1 42.1 14.5 - - - 12 6 20

PX5/16-02□ 5/16 R1/4 1151.7 45.7

14.5 18.114 3.4 17.2 15.1

145.9 29

49.3 43.3 14.5 - - - 6.7 25

PX5/16-03□ 5/16 R3/8 1253.5 47.2

14.5 18.114 3.4 17.2 15.1

175.9 43

52.5 46.2 14.5 - - - 6.7 36

PX3/8-01□ 3/8 R1/8 855.3 51.3 18 20.7 18 4.5 19.5 18 17

641

49.8 45.8 17.5 20.2 17.5 - - - 12 27

PX3/8-02□ 3/8 R1/4 1158.3 52.3 18 20.7 18 4.5 19.5 18 17 6.8 4453.6 47.6 17.5 20.2 17.5 - - - 14 8 33

PX3/8-03□ 3/8 R3/8 1259.3 53 18 20.7 18 4.5 19.5 18

176.8 52

56.7 50.4 17.5 20.2 17.5 - - - 8.3 44

PX3/8-04□ 3/8 R1/2 1562.3 54.1 18 20.7 18 4.5 19.5 18

216.8 74

60.2 52 17.5 20.2 17.5 - - - 8.3 67

PX1/2-02□ 1/2 R1/4 1163.8 57.8

21 23.720 4.2 22.5 21 21

862

58.9 52.9 21 - - - 14 39

PX1/2-03□ 1/2 R3/8 1264.8 58.5

21 23.720 4.2 22.5 21 21 8 63

60.9 54.6 21 - - - 17 10 51

PX1/2-04□ 1/2 R1/2 1567.8 59.6

21 23.720 4.2 22.5 21

218 78

65 56.8 21 - - - 11 74・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

2-øP

R

Hex.

TLB

2-C F

J2-øD

ød

A ALB

RMetric thread type

RHex.

LB

2-C

J2-øD

A

ALB

2-øP

R

2014 NEW PRODUCTS

PX Branch Y（inch - R）


33

Unit：㎜

Model codeTube O.D.


Orifice (ø㎜ )

Weight (g)

PX5/32-U10U□ 5/32 No.10-32UNF 337.6 34.6

10 14.911 3.2 14.1 10.4 7/16 1.8 11

32.9 29.9 10.3 - - - 5/16 2.4 8

PX5/32-N1U□ 5/32 1/8-27NPT 840.6 36.5

10 14.911 3.2 14.1 10.4

7/162.7 15

38.4 34.3 10.3 - - - 2.8 14

PX5/32-N2U□ 5/32 1/4-18NPT 1143.6 37.8

10 14.911 3.2 14.1 10.4

9/162.7 23

43.4 37.6 10.3 - - - 2.8 20

PX3/16-U10U□ 3/16 No.10-32UNF 341.8 38.8

12.5 17.412 3.4 16.2 13.5 1/2 1.8 17

38.7 35.7 12.5 - - - 7/16 2.4 14

PX3/16-N1U□ 3/16 1/8-27NPT 844.8 40.6

12.5 17.412 3.4 16.2 13.5 1/2 4.2 19

41.7 37.5 12.5 - - - 7/16 3.3 16

PX3/16-N2U□ 3/16 1/4-18NPT 1147.8 42

12.5 17.412 3.4 16.2 13.5

9/164.2 27

48.7 42.9 12.5 - - - 3.3 23

PX1/4-U10U□ 1/4 No.10-32UNF 341.4 38.4

12.5 1712 3.4 15.8 13.5 1/2 1.8 16

38.3 35.3 12.5 - - - 7/16 2.4 13

PX1/4-N1U□ 1/4 1/8-27NPT 844.4 40.2

12.5 1712 3.4 15.8 13.5 1/2 4.4 19

41.3 37.1 12.5 - - - 7/16 4.6 16

PX1/4-N2U□ 1/4 1/4-18NPT 1147.4 41.6

12.5 1712 3.4 15.8 13.5

9/164.4 26

48.3 42.5 12.5 - - - 5.3 22

PX1/4-N3U□ 1/4 3/8-18NPT 1249.2 43.1

12.5 1712 3.4 15.8 13.5

11/164.4 40

51.3 45.2 12.5 - - - 5.3 35

PX5/16-N1U□ 5/16 1/8-27NPT 848.7 44.6

14.5 18.114 3.4 17.2 15.1 9/16 5.9 24

46.1 42 14.5 - - - 1/2 6.0 21

PX5/16-N2U□ 5/16 1/4-18NPT 1151.7 45.9

14.5 18.114 3.4 17.2 15.1 9/16 5.9 30

49.3 43.5 14.5 - - - 9/16 6.7 26

PX5/16-N3U□ 5/16 3/8-18NPT 1253.5 47.4

14.5 18.114 3.4 17.2 15.1

11/165.9 43

52.5 46.4 14.5 - - - 6.7 38

PX3/8-N1U□ 3/8 1/8-27NPT 855.3 51.2 18 20.7

184.5 19.5 18 11/16

6.0 42

49.8 45.7 17.5 20.2 - - - 1/2 28

PX3/8-N2U□ 3/8 1/4-18NPT 1158.3 52.5 18 20.7

184.5 19.5 18 11/16 6.8 44

53.6 47.8 17.5 20.2 - - - 9/16 8.0 33

PX3/8-N3U□ 3/8 3/8-18NPT 1259.3 53.2 18 20.7

184.5 19.5 18

11/166.8 53

56.7 50.6 17.5 20.2 - - - 8.3 45

PX3/8-N4U□ 3/8 1/2-14NPT 1562.3 54.2 18 20.7

184.5 19.5 18

7/86.8 75

60.2 52.1 17.5 20.2 - - - 8.3 69

PX1/2-N2U□ 1/2 1/4-18NPT 1163.8 58

21 23.720 4.2 22.5 21 7/8

8.0 63

58.9 53.1 21 - - - 9/16 39

PX1/2-N3U□ 1/2 3/8-18NPT 1264.8 58.7

21 23.720 4.2 22.5 21 7/8 8.0 65

60.9 54.8 21 - - - 11/16 10.0 51

PX1/2-N4U□ 1/2 1/2-14NPT 1567.8 59.7

21 23.720 4.2 22.5 21

7/88.0 80

65 56.9 21 - - - 11.0 75・-C in □ is Clean-room package. W in □ is Light-gray spec. W-C in □ is Light-gray and Clean-room package spec. –UC in □ is Ultra-sonic clean wash spec. Apply blank for standard model.*L dimensions of taper thread type are reference dimensions after tightening screw.*The prices remain the same with current models.

Metric thread type

RHex.

LB

2-C

J2-øD

A

ALB

2-øP

RMetric thread type

2-øP

R

Hex.

TLB

2-C F

J2-øD

ød

A ALB

RUnified Unified


PX Branch Y（inch - NPT）


34

HEAD OFFICE AND PLANT3-9-32, OSACHIIZUHAYA, OKAYA-CITY, NAGANO-PREF., 394-0089 JAPANTEL: 0266-28-6072 FAX: 0266-28-7349Web: www.pisco.co.jp

OVERSEAS OPERATION TEAM3884-1 MINAMIMINOWA, KAMIINA, NAGANO-PREF., 399-4588 JAPANTEL: +81-(0)265-76-7751 FAX: +81-(0)265-76-3305Web: http://en.pisco.co.jp/ 　E-mail : [email protected]

PISCO USA, INC. (sales office)463 W. Wrightwood Ave.,Elmhurst, Illinois 60126,U.S.A.Tel: +1-630-993-3500 　FAX:+1-630-993-3501Web: www.pisco.com 　E-mail: [email protected]

NIHON PISCO SINGAPORE PTE. LTD. (sales office)5012 Ang Mo Kio Avenue 5, #02-10 Techplace II, Singapore, 569876, SINGAPORETel: +65-6481-5866 　Fax: +65-6481-7289Web: www.pisco.com.sg 　E-mail: [email protected]

PISCO TAIWAN CO., LTD. (Sales & Factory)NO. 71-2, HUAZONG RD., XUEJIA DIST., TAINAN CITY, 72645, TAIWAN, R.O.C.Tel : +886-6-7820701 　FAX: 886-6-7820710

PISCO KOREA PNEUMATICS CO., LTD403-3TH FLOOR, BUCHEON TECHNO PARK, 193, YAKDAE-DONG, WONMI-GU, BUCHEON-CITY, GYEONGGI-DO, KOREATEL: +82-32-327-9795 　FAX : 82-32-327-0385Web: www.pisco.co.kr 　E-mail: [email protected]

NIHON PISCO Co., Ltd. Bangkok Representative Office2 Jasmine Bldg., No.5, 12th Floor, Soi Prasarnmitr (Sukhumvit 23), Sukhumvit Rd.,North Klongtoey, Wattana, Bangkok 10110, Kingdom of ThailandTel: +66-(0)2-612-7366 　Fax: +66-(0)2-612-7399E-mail: [email protected]

ISO 9001CertifiedISO14001

● Recommended screw tightening torque,Sealock color and gasket material for subject modelsThread type Thread size Tightening torque(N・m) Sealock color Gasket material

Metric threadM5×0.8 1～ 1.5

ー PPSM6×1 2～ 2.7

Taper pipe thread※

R1/8 4.5～ 6.5

White ーR1/4 7～ 9

R3/8 12.5～ 14.5

R1/2 20～ 22※ They are common tightening torques for all products equipped with taper pipe thread.

Conventionally, two pieces of Tube Fittings had to be used for the size reduction fromφ12 to φ8 by using φ10 in the middle,but now one piece of Tube Fitting can realize same size reduction !

Each layer of double or triple banjo type can make a 360-degree turn individually.

Triple-tee or twin-triple-tee are good for centralized piping.

φ8

When the main piping is intensively branched,

tube lead-out direction can be changed freely after the installation of Tube Fitting.

Suitable for centralized branching.

Tube lead-out direction can be adjusted to multiple directions.

Many size variations are availableTwo-step size reduction is

realized.Unequal plug-in straight type has three-

step size reduction models

Introduction of Tube Fitting 　-There are many other configurations available to suite your purposes.-

There are many other configuration lineups are available. Please check our website for details.

φ12Tube O.D. (Example)

φ10

PISCO　　　　SEARCH▼▼

2014 NEW PRODUCTS

●The specifications are subject to change without advance notice. 2014.08 PDF

PISCO push-in fitting, superior in operability and ... · PISCO push-in fitting, superior in...

Documents

Transcript of PISCO push-in fitting, superior in operability and ... · PISCO push-in fitting, superior in...