perma STAR CONTROL - SINGLEPOINT LUBRICATION LTD · 2015. 7. 8. · perma STAR CONTROL is used for...
Transcript of perma STAR CONTROL - SINGLEPOINT LUBRICATION LTD · 2015. 7. 8. · perma STAR CONTROL is used for...
perma STAR CONTROL TIME and IMPULSE mode in one system
Lubrication based on operating hours or on impulse
perma STAR CONTROL is machine / PLC controlled and can easily be integrated into machines with external power supply. The operating status can be transmitted to the PLC. The lubrication system offers two operating modes - TIME and IMPULSE - for more flexibility. In TIME mode, discharges are only carried out when the machine is in operation. In IMPULSE mode, the system discharges a predefined lubricant amount every time external power is applied. The desired mode can be selected via the display. perma STAR CONTROL consists of an electro-mechanical drive unit with LCD display and an LC unit (available in three different sizes 60 cm3, 120 cm3, 250 cm3). The system discharges exact amounts independent of temperature and up to 6 bar counter pressure.
Generation2.0
perma-tec GmbH & Co. KG | www.perma-tec.com | 2
Applications
perma STAR CONTROL is used for single-point lubrication of roller- and sliding bearings, sliding guides, open gears,gear racks, spindles, shaft seals, and chains. This lubrication system is ideal for applications that require preciselubricant metering. It is a preferred system for electric motors with very specific relubrication amounts.perma STAR CONTROL is protected against dust and water jets when the individual parts are assembled correctly (IP 65).
© 2
014/
12 ·
Vers
ion:
1.1
· Pa
rt n
o. 1
0950
4Technical Information
Drive – reusableElectromechanicalPower supplyExternal 9 - 30 V DC, Imax 0.5 ADischarge period Time controlled (TIME)Impulse controlled (IMPULSE)Lubricant volume 60 cm³, 120 cm³ or 250 cm³Operating temperature -20 °C to +60 °CPressure build-up 6 barProtection classIP 65 Lubricants Grease up to NLGI 2 / oil
LCD displaywith push button
Gearmotor
LubricantLCs with oilfilling require a separate oilretaining valve
Piston
Cable connector
Product characteristics Benefits
Electromechanical drive with external power supply
All around visible LED lights (red / green) signal function and possible errors
LCD display with push button shows discharge settings, LC size and operating status
Push button for setting mode, LC size, discharge amount and PIN
Reliable, precise lubricant discharge independent of temperature and counter pressure
Quick function control via visual signals on the lubrication system or electronic signals on the machine's fault reporting system saves time and improves overall workflow
Quick and easy control of settings and remaining impulses / operating hours until LC exchange
More flexibility with simple programming of TIME or IMPULSE mode; settings can be changed at any time
PIN prevents manipulation
DimensionsLC S60: ø 72 x 152 mmLC M120: ø 72 x 175 mmLC L250: ø 72 x 225 mm
Pressure build-up to 6 barallows remote mounting
Counter pressure check and manual discharge (purge function)
Remote installation at safe- and easy-to-access places (maximum 5 m) reduces workplace accidents and saves time
Less equipment downtime since the exchange can be carried out while the machines are running
Lubrication point can be purged to clear blockages
Cable STAR CONTROL Part no. 5 m 108432 10 m 108431
STAR CONTROL Drive Gen 2.0 Part no. 108985 TIME Mode Setting: 1, 2, 3, ... 12 monthsFurther settings on request
IMPULSE ModeSetting: 0.1 - 9.5 cm3 / Impulse
perma STAR LC S60 / M120 / L250Part no. go to perma Catalogue
Support flange STAR G1/4o x G1/4i Part no. 101416