2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 1/7

metal+mettlea goldsmith at her bench: thoughts, tips & inspiration

TAG ARCHIVES: PATINAS

A blush of red in the studio

D.Bréchault. Bowl, copper, patina. Dia.: 9.5 cm

As I walk through the neighbourhood these days, I notice the first blushing trees. So many shades of red:

burgundy, crimson, vermillion, even some magenta – and some rusty reds too. I enjoy these rich and

vibrant colours and I always have the urge to run to my studio and add splashes of colours to my

jewellery.

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 2/7

The palette of a metalsmith does not have to be limited to a few muted shades of silver and gold. Metals

like copper, brass, and bronze lend themselves particularly well to a wide variety of colours (or patinas)

and can open up all kinds of possibilities. Metal patination has been used in different parts of the world

for a very long time. Years ago, Ayako Kuroki, a distinguished goldsmith and teacher from Tokyo, Japan,

told me about hiirodo the red copper patina used in traditional Japanese metalwork. Here is an example

of tsuba (sword guards) with a deep maroon red copper patina:

Tsubas (Asian Art Museum, San Francisco)

Photo : Wikipedia Commons

Several types of methods can be used to colour metal, depending on the colours you want to obtain –

heat or chemicals, or a combination of both. For now, let’s deal with these rich and vibrant red autumn

colours (I will talk about the greens, and the blues in another post). Here is how you can incorporate

them into your work. Note that these recipes will only work with copper.

Remember to wear goggles, and make sure there is sufficient ventilation in your studio.

- Heat up the copper with the torch to a high temperature (until the metal is red hot).

- Quench immediately in a boiling water and salt solution (Salt/water solution: 3 tablespoons salt to 3

cups water).

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 3/7

This creates a deep brick red patina:

Depending on the intensity of the flame, or how long the metal is heated up, you’ll get darker shades of

red or purplish red. If the metal is heated up for a bit longer, this can produce a marbled effect of red and

black,

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 4/7

or a smoky effect like this:

Heating up the metal and quenching it in boiling water without salt will produce some rich tones of red as

well, but generally more on the rusty or orangy side:

Here is another recipe:

First, coat the metal with a mixture of borax flux and water, and heat up with the torch. Quench in boiling

water. Usually the more interesting colours appear on the back side of the sheet. Depending on what

type of flux is used (borax cone ground, and mixed with water, or liquid flux like “Batterns”), you’ll get

various results, from a deep burgundy with streaks of orange to a more mottled pattern:

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 5/7

And for a different mottled effect, try sprinkling salt on the metal as you are heating it up. Keep the flame

on only until the grains of salt melt, then quench in boiling water right away. Results vary. On this sample,

there are intricate patterns of purple and rose tones mixed with some smoky greys.

Sometimes, I like to texture the metal before coloring it; it adds more depth and another layer of interest

to the design. There are many types of surface treatments available. In these examples, I used etching

and roll-printing:

0

Stumble

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 6/7

Important note: Don’t pickle your metal, as the pickling solution would remove the patina!

This heat patina is stable and fairly tough, so it does not really require much protection, especially if the

patinated metal is in a recessed area that will prevent scratches. Otherwise a thin coat of soft beeswax will

work well.

Now, if you consider yourself a control freak, these techniques are probably not for you! As with most

patinas, results are not always consistent, and are difficult to predict, but that’s the beauty of it, and for

me that’s the fun of it too. Factors such as the gauge of the metal, the intensity of the flame, or the

temperature of the water will affect the results, so keep experimenting!

Share this:

Twitter Facebook Pinterest Email Tumblr Google More

This entry was posted in how-to and tagged copper, Dominique Brechault, fall colours, heat patina, how-

to, jewelry, metal coloring, metal work, metalsmithing, patinas, red on October 20, 2012

[https://metalandmettle.wordpress.com/2012/10/20/a-blush-of-red-in-the-studio/] .

Like

5 bloggers like this.

Follow

Follow “metal+mettle”

Get every new post delivered

to your Inbox.

Join 78 other followers

Enter your email address

Sign me up

Pow ered by WordPress.com

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 7/7