Pak- lok Installation Instructions
description
Transcript of Pak- lok Installation Instructions
![Page 1: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/1.jpg)
Pak-lok Installation InstructionsQuick Installation Guide00825-0300-4809 rev. DB
![Page 2: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/2.jpg)
Drill the Hole into the Pipe Using a Drill Bit or Hole Saw
Tag with correct drill hole size attached to the Annubar
![Page 3: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/3.jpg)
Clean the Area with a Grinder to Prepare for the Surface for Welding
![Page 4: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/4.jpg)
Weld Pak-lok Body to the Pipe
Make sure the mounting hardware is centered over the mounting hole
![Page 5: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/5.jpg)
Insert Studs into the Packing Body
![Page 6: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/6.jpg)
Mark the End of the Sensor With a Felt Tip Marker Do not mark if order with special cleaning (Option Code P2, PA)
![Page 7: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/7.jpg)
Insert the Flowmeter Until the Tip Contacts the Opposite Side Pipe WallRotate Annubar back and forth.
![Page 8: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/8.jpg)
Remove the Flowmeter and Verify the Sensor Tip Made ContactSome of the marker should have been rubbed off.
![Page 9: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/9.jpg)
Align the Flow Arrow and Insert the Annubar
![Page 10: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/10.jpg)
Insert a Packing Ring Underneath the Compression Plate and the FollowerThe split in the packing ring should face one of the three studs. Use the Compression Plate and Follower to compress the packing into the Pak-lok Body.
![Page 11: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/11.jpg)
Packing Goes Below the Compression Plate and Follower
NO!
YES!
NO!
Compression PlateFollower
Weld Ring
Packing
![Page 12: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/12.jpg)
The Next 2 Packing Rings should be Inserted so the Split is 120 ۫ Apart
The split in each packing ring should face a different stud which are 120 degrees apart
![Page 13: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/13.jpg)
Insert the Second Packing Ring with the Split Facing a Different StudCompress it with the Follower and Compression Plate
![Page 14: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/14.jpg)
Insert the Third Packing Ring with the Split Facing a Different StudCompress it with the Follower and Compression Plate
![Page 15: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/15.jpg)
Place the Split Ring Washers on the Studs
![Page 16: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/16.jpg)
Thread the Nuts onto the Studs
![Page 17: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/17.jpg)
Tighten Each Nut ½ Turn in Succession
![Page 18: Pak- lok Installation Instructions](https://reader036.fdocuments.in/reader036/viewer/2022081420/568161da550346895dd1e60d/html5/thumbnails/18.jpg)
Tightened the Nuts Until the Split-Ring Washers are Flattened
The Split-Ring washers are specially designed to be flat at the appropriate Torque level for the Annubar