Page 1 of 28 Group A (VLAN A) 1) VID: 2 2) IP Interface: a) IP Address: 192.168.100.254 b) Subnet...
-
Upload
brent-mccormick -
Category
Documents
-
view
227 -
download
0
Transcript of Page 1 of 28 Group A (VLAN A) 1) VID: 2 2) IP Interface: a) IP Address: 192.168.100.254 b) Subnet...
Page 1 of 28
Group A (VLAN A)1) VID: 2
2) IP Interface:a) IP Address: 192.168.100.254b) Subnet Mask: 255.255.255.0
3) Ports: 1x to 8x
PC10IP Address: 192.168.100.1
Subnet Mask: 255.255.255.0Gateway IP: 192.168.100.254
DES-3326 Layer 3 SwitchIP Address: 192.168.22.1
Subnet Mask: 255.255.255.0
Group B (VLAN B)1) VID: 3
2) IP Interface:a) IP Address: 192.168.200.254b) Subnet Mask: 255.255.255.0
3) Ports: 17x to 24x
PC20IP Address: 192.168.200.1
Subnet Mask: 255.255.255.0Gateway IP: 192.168.200.254
Default VLAN1) VID: 1
2) IP Interface:a) IP Address: 192.168.22.1
b) Subnet Mask: 255.255.255.03) Ports: 9x to 16x
AdministratorIP Address: 192.168.22.10
Subnet Mask: 255.255.255.0Gateway IP: 192.168.22.1
Page 2 of 28
2.1) Firstly, ensure that your Console (RS-232) cable is connected from your computer to the DES-3326 Switch.
2.2) Execute the “Hyper Terminal” program. (as shown above)
2.3) Key in the “User name” & “Password” as prompted.
Page 3 of 28
3.1) Select the <Remote Management Setup> option.
Page 4 of 28
4.1) Key in this Switch’s IP Address in the <IP Address:>, and also key in this Switch’s Subnet Mask in the <Subnet Mask:>. Example: 192.168.22.1 {IP} 255.255.255.0 {Subnet Mask}.
4.2) Next, select the <APPLY> option.
Page 5 of 28
5.1) Go back to the <Main Menu>.
5.2) Select the <Save Changes> option.
Page 6 of 28
6.1) Wait till you see the sentence “Press any key to continue” (in the above screen).
6.2) Next, press any key.
Page 7 of 28
7.1) Select the <Switch Settings> option.
Page 8 of 28
8.1) Select the <Switch Operation Mode> option.
Page 9 of 28
9.1) Press <Space Bar>, to select “IP Routing, Support IEEE 802.1Q VLANs”.
9.2) Next, select <Apply> option.
Page 10 of 28
10.1) Key in “y”, when you are prompted (shown above).
10.2) Next, wait till the Switch finish its rebooting.
Page 11 of 28
11.1) Ensure that you see “Layer 3 Switch” at the top right corner. If not, please repeat this configuration from Step 7.1
11.2) Key in the “User name” & “Password” as prompted.
Page 12 of 28
12.1) Select the <VLANs> option.
Page 13 of 28
13.1) Select the <Edit 802.1Q VLANs> option.
Page 14 of 28
14.1) In the <VID>, key in “2”.14.2) In the <VLAN Name>, key in “VLANA”.14.3) Set port 1 to 8’s <Membership> and <Tagging> to “E” and “U”. * Note: Use the <E> and <U> keys on your Keyboard.14.4) Next, select the <APPLY> option.14.5) Ensure that “VLANA” entry appears after you applied these settings. If not, please repeat this configuration from Step 14.1
Page 15 of 28
15.1) In the <VID>, key in “3”.15.2) In the <VLAN Name>, key in “VLANB”.15.3) Set port 17 to 24’s <Membership> and <Tagging> to “E” and “U”. * Note: Use the <E> and <U> keys on your Keyboard.15.4) Next, select the <APPLY> option.15.5) Ensure that “VLANB” entry appears after you applied these settings. If not, please repeat this configuration from Step 15.1
Page 16 of 28
16.1) Next, select the <Configure 802.1Q Port Settings> option.
Page 17 of 28
17.1) In the <Configure Port from [ ] to [ ]>, key in “1” and “8”.
17.2) In the <PVID> , key in “2”.
17.3) Next, select the <APPLY> option.
17.4) After the applying the above settings, ensure that from Port 1 to 8, you see PVID=2. If not, please repeat this configuration from Step 17.1.
Page 18 of 28
18.1) In the <Configure Port from [ ] to [ ]>, key in “17” and “24”.
18.2) In the <PVID> , key in “3”.
18.3) Next, select the <APPLY> option.
18.4) After the applying the above settings, ensure that from Port 17 to 24, you see PVID=3. If not, please repeat this configuration from Step 18.1.
Page 19 of 28
19.1) Select the <Layer 3 IP Networking> option.
Page 20 of 28
20.1) Select the <Setup IP Interface> option.
Page 21 of 28
21.1) In the <Interface Name>, key in “GroupA”.21.2) In the <IP Address>, key in “192.168.100.254”.21.3) In the <Subnet Mask>, key in “255.255.255.0”.21.4) In the <VID>, key in “2”.21.5) Next, select the <APPLY> option.21.6) After the applying the above settings, ensure that you see the above settings are shown. If not, please repeat this configuration from Step 21.1.
Page 22 of 28
22.1) In the <Interface Name>, key in “GroupB”.22.2) In the <IP Address>, key in “192.168.200.254”.22.3) In the <Subnet Mask>, key in “255.255.255.0”.22.4) In the <VID>, key in “3”.22.5) Select the <APPLY> option.22.6) Follow by, pressing the <CTRL> and <N> keys (on your keyboard), to view the next page.22.7) After the applying the above settings, ensure that you see the above settings are shown. If not, please repeat this configuration from Step 22.1.
Page 23 of 28
23.1) At “PC10” (GroupA computer), execute the <MS-DOS Prompt>.23.2) Key in “ping 192.168.100.1” (its own IP address), and press the <Enter> key.23.3) Key in “ping 192.168.100.254” (its own VLAN Interface IP address), and press the <Enter> key.23.4) Key in “ping 192.168.22.1” (DES-3326’s IP address), and press the <Enter> key.23.5) Key in “ping 192.168.200.254” (VLAN B Interface IP address) , and press the <Enter> key.23.6) Key in “ping 192.168.200.1” (VLAN B computer’s IP address) , and press the <Enter> key.23.7) Ensure that all the above mentioned “Ping” have “reply”.
1
2
3
4 5
Page 24 of 28
54
3
2
1
24.1) At “PC20” (GroupB computer), execute the <MS-DOS Prompt>.24.2) Key in “ping 192.168.200.1” (its own IP address), and press the <Enter> key.24.3) Key in “ping 192.168.200.254” (its own VLAN Interface IP address), and press the <Enter> key.24.4) Key in “ping 192.168.22.1” (DES-3326’s IP address), and press the <Enter> key.24.5) Key in “ping 192.168.100.254” (VLAN A Interface IP address) , and press the <Enter> key.24.6) Key in “ping 192.168.100.1” (VLAN A computer’s IP address) , and press the <Enter> key.24.7) Ensure that all the above mentioned “Ping” have “reply”.
Page 25 of 28
23.1) Next, select the <Network Monitoring> option.
Page 26 of 28
24.1) Select the <Routing Table> option.
Page 27 of 28
25.1) Ensure that you see the above entries (shown above). If not, please repeat this configuration from Step 19.1
* Note: The above entries will only show when there are network traffics between the IP segments or VLANs (Example: GroupA’s computer ping GroupB’s Computer).
Page 28 of 28
26.1) Select the <Logout> option.
26.2) Lastly, you may close the “Hyper Terminal” program.
=== The End ===