P-C3_inst
2
Canopy Installation Instructions Version 05-2008 Copyright © MP Lighting All technical information in this document is subject to change. T 604 708 1184 mplighting.com 1 2 Unbraid outer woven wire to expose 1/2” (13mm) of inner wire. Twist outer strands tightly together. Strip 1/8” (3mm) of insulation from inner wire. 3 4 5 92mm 3-5/8” 92mm 3-5/8” C3 Connect braided coax wire to 60W minimum 12V transformer. Next, connect primary to driver input wires then fit into electrical box. For remote driver connect fixture wires to low voltage wiring. Tighten screws with Allen Key. Align canopy to electrical box. If necessary mount universal crossbar to electrical box then mount canopy to crossbar. Read all instructions. Risk of fire and electrical shock. Turn off power before installation. Connect to 12V electronic transformer. Keep this document as a reference. CAUTION • • • • Do not over tighten screws. • Test installation by leaving fixture on for 20-30 minutes to ensure proper operation. • Maximum 50W lamp. • Use only low voltage electronic dimmers. • 13mm 1/2” 3mm 1/8” INPUT PRIMARY 120/277V 12V Transformer Ceiling Mount Pendant Mount C3 Canopy and Pendant
-
Upload
mp-lighting -
Category
Documents
-
view
213 -
download
0
description
http://www.mplighting.com/pdf/installation/P/P-C3_inst.pdf
Transcript of P-C3_inst
CanopyInstallation Instructions
Version 05-2008
Cop
yrig
ht ©
MP
Lig
htin
g A
ll te
chni
cal i
nfor
mat
ion
in th
is d
ocum
ent i
s su
bjec
t to
chan
ge.
T 604 708 1184 mplighting.com
1
2
Unbraid outer woven wire to expose 1/2” (13mm) of inner wire. Twist outer strands tightly together.
Strip 1/8” (3mm) of insulation from inner wire.
3
4
5
92mm3-5/8”
92mm3-5/8”
C3
Connect braided coax wire to 60W minimum 12V transformer. Next, connect primary to driver input wires then fit into electrical box.
For remote driver connect fixture wires to low voltage wiring.
Tighten screws with Allen Key.
Align canopy to electrical box. If necessary mount universal crossbar to electrical box then mount canopy to crossbar.
Read all instructions.
Risk of fire andelectrical shock.Turn off powerbefore installation.
Connect to 12V electronic transformer.
Keep this documentas a reference.
CAUTION•
•
•
•
Do not over tighten screws.
•
Test installation by leaving fixture on for 20-30 minutes to ensure proper operation.
•
Maximum 50W lamp.•
Use only low voltage electronic dimmers.
•
13mm1/2”
3mm1/8”
INPUT PRIMARY 120/277V12V Transformer
Ceiling Mount Pendant
Mount C3 Canopy and Pendant
C3 PendantPendant Length
Adjustment Instructions
Version 05-2008
Cop
yrig
ht ©
MP
Lig
htin
g A
ll te
chni
cal i
nfor
mat
ion
in th
is d
ocum
ent i
s su
bjec
t to
chan
ge.
T 604 708 1184 mplighting.com
1 Cut coax wire to desired length.
2
3
Unbraid outer woven wire to expose 1/2” (13mm) of inner wire. Twist outer strands tightly together.
Strip 1/8” (3mm) of insulation from inner wire.
Adjust Pendant Length on C3 Canopy
4 Remove setscrew on canopy.
5 Place strain relief in center hole and pull wire through canopy.
6 Tighten setscrew when pendant is adjusted to desired height.
13mm1/2”
3mm1/8”
Read all instructions.
Ensure setscrews are tight and firmly holding wire to prevent pendant from falling.
Keep this document as a reference.
CAUTION•
•
•
Make sure strain relief is positioned properly with open side facing away from setscrew. Failure to do so may cause setscrew to pierce cable and short pendant.
•
