OWNERS MANUAL CHARGER 9 - My Wheel Horsemywheelhorse.com/graphics/file/Tractors/Tractor_1968... ·...
Transcript of OWNERS MANUAL CHARGER 9 - My Wheel Horsemywheelhorse.com/graphics/file/Tractors/Tractor_1968... ·...
-
,
, i
\ ! , I , I ! j i ! , 1 , , , j
" , !
[ , ,
, !
!.
, , , ! , i ,
, " , ,
.1
-
WHE L-HORS PRODUCTS, INC.
• • • • • • • • • • • • •
• • • • • • • • • • • • • • • • • • • • • • • • • •
OWNERS MANUAL
CHARGER 9
MOD L
•
SOUTH BEND, IND.
www.MyWheelHorse.com
-
ASSEMBLY
A. The tractor is shipped in one carton with the rear wheel and tire assemblies, Part No. 5432, in a separate carton.
B. Mount rear wheels to hubs using the ten lug bolts, Part No. 1004.
C. Mount front wheels to spindles using the %-16 x Ys Nylok bolts, Part No. 908033-6 and washers, Part No. 2844.There are two shim washers, one .015 thick and one .050 thick, in the loose part package for each wheel. Use one or both as shown on the exploded view drawing to provide a close flt. Press on hub caps.
D. To mount the steering wheel slip the collar, Part No.7 468, on the steering shaft, insert the Wood-ruff Key, Part No. 937014, mount the steering wheel, and secure with the )4 x 1)4 roll pin, Part No. 933215.
BATTERY
The battery installed in the tractor is a dry charged battery. It is important that you properly prepare this battery to insure good service and long life.
1. Remove vent caps. Remove or destroy any seal-ing device which may have been used to close or re-strict the vent openings.
2. Fill each cell of the battery to the proper level with the battery electrolyte.
NOTE: Temperature of battery and electrolyte at time of fllling should be above 60°F. Never flll bat-tery in the vehicle.
3. BOOST CHARGE: 15 amps. for 10 minutes or 7 amps. for 30 minutes. Adjust electrolyte level, if necessary, after charge.
4. Install battery with battery posts toward the rear of tractor. Start engine. After battery has been in service, add only approved water.
DO NOT ADD ACID.
TIRES
The front tires are 16 x 5.50-8 and should be in-flated to 12 pounds of air pressure. The rear tires are 8.50 x 12 and should have 6 to 8 pounds of air pres-sure. The tires can also be fliled with ballast if desired. Ordinarily this is not necessary as the weight of the operator will add sufficient weight for adequate trac-tion.
BEFORE YOU START
There is NO OIL in the crankcase of the engine when shipped from the factory. OIL ... See Engine Manual.
- 2
Wheel-a-Matic Transmission: The transmission has been fliled with Automatic Transmission fluid at the factory. (This is type "A" automatic transmission fluid, which is used in automobiles and may be purchased at any service station.)
A. Remove Plug from transmission flll pipe, (lo-cated under seat) and insert dipstick, Part No. 6155. (See Fig. I). Now check level of transmission fluid to make sure transmission is fliled to proper level.
B. To enable moving the tractor by hand you must open the towing valve. (See Towing Instructions.)
Lubricate all grease flttings with a regular pressure gun lubricant every eight to ten hours of operation. Refer to Figure IV for the location of grease flttings.
A light machine oil should be used where indicated.
OPERATING INSTRUCTIONS
The speed, direction and braking are controlled by the control handle located on the right side.
• To go Forward push the control handle Forward.
• To go Backward pull the control handle Back.
• To Stop put control handle in Neutral position.
• You may also Stop the tractor at anytime by depressing the foot pedal on the left side.
The tractor speed is affected instantly by the move-ment of the control handle. For safest operation the control handle should not be moved too rapidly, especially on grades.
TOWING INSTRUCTIONS
This tractor should never be towed or pushed with-out first opening the towing valve.
A. The towing valve is located on the top sur-face of the pump. To push or tow folloVV; directions on towing decal. (See Fig. I)
B. CAUTION: Do not tow for long distance or over a speed of seven (7) miles per hour.
STARTING ENGINE
1. Before starting the engine flll gas tank (located under the hood) with a good grade of regular gas, and open valve on gas tank.
2. The tractor has a key starter-switch. Turn key all the way to right to start engine.
3. Pull throttle lever ~ way out and turn to the right to lock it in position. Note: The throttle control has a locking device. Turn the throttle control to the left to unlock, adjust to the desired position and turn to the right to lock.
www.MyWheelHorse.com
-
4. Pull choke lever all the way out to choke en-gine. If engine is warm and has been running, choking may not be necessary.
5. When engine starts push choke in to off posi-tion and regulate throttle control by tUrning to the left to unlock and push in or out to desired speed.
6. When starting tractor in cold weather set the park brake. This releases the drive belt, and the engine does not have to turn the transmission.
PARKING BRAKE
The parking brake is located on the right side of the tractor. (See Figure IV.) To set the parking brake pull on the handle. Brake should always be set when dismounting from tractor, especially on a grade, otherwise the tractor may creep. When brake is set 'the drive belt is automatically released. Caution: Do not set parking brake while tractor is in motion as this may result in damage to the transmission. Always depress foot pedal (on left side) before releasing parking brake.
TRANSMISSION CARE
Change oil filter after first ten hours. Change oil and filter every year or 100 hours of operation, whichever occurs first. The transmission oil capacity is approximately four (4) quarts.
• Use only type "A" automatic transmission oil.
• Check oil periodically and maintain at proper level as indicated on dipstick.
CARE OF TRACTOR
1. Keep tractor greased and oiled regularly. Re-fer to Figure IV for the location of grease fittings. Check transmission and engine case oil levels.
2. Keep engine air cleaner clean. This will add to engine life.
3. Keep tires properly inflated. See previous in-structions.
4. Keep tractor covered and in a dry place when not in use.
5. Keep grass and dirt out of engine cowling as these will stop the flow of air and decrease engine life.
6. Keep grass and dirt off transmission for good transmission cooling.
7. Battery - Check electrolyte level periodically.
NOTE: If tractor has been in storage it may be necessary to recharge battery.
8. Control Handle Friction Adjustment:
- 3
The control lever is friction loaded so it will hold at any desired speed. The tension has been adjusted at the factory and should need little or no attention. If the handle does not stay where it is set during opera-tion, the friction may be increased QY releasing the locknut and tightening the collar-friction adjustment. (See Figure III.) The proper amount of friction is obtained when approximately five pounds of force at the handle grip moves the control lever. Be sure to tighten the locknut after proper tension has been reached. The friction collar is self lubricating and does not require lubrication.
9. Neutral Adjustment:
A. If tractor should creep while in neutral posi-tion this can be corrected. To check for creep place tractor on level surface with engine running, and de-press foot pedal. Creep on slopes is normal and can-not be entirely eliminated.
B. To make neutral adjustment (See Figure II).
1. Block rear wheels off ground.
2. Remove instruction plate, (located in front of the seat) by removing the four screws which hold it.
3. Loosen set screw in arm with allen wrench (See Figure II).
4. Depress foot pedal on left side.
5. With tractor engine running and park brake disengaged, insert short screwdriver through hole in nylon cam and rotate the eccentric cam pin until rear wheels stop. Now retighten set screw in arm and re-place plate.
6. NOTE: The lobe on the eccentric pin must be upward for proper operation.
7. When replacing belts be sure to purchase genuine Wheel Horse Belts, as these belts are specifically designed for each applica-tion. NOTE: Make sure all pulleys are in line.
8. Your tractor is only as good as the service you give it. See your Wheel Horse Dealer for a thorough check-up after each season of use.
ATTACHING TOOLS
Complete information on the assembly, attachment, operation and service of the many attaching tools will be provided with each attachment.
All drawn implements attach in seconds. Simply lift the tractor hitch pin, insert the tongue, and replace pin.
www.MyWheelHorse.com
-
LIGHTS
o w cr
LIGHT SWITCH 8 cr
TAIL LIGHT LIGHTER
ENGINE
SPARK PLUG
BLACK
BATTERY
IGNITION-START SWITCH
WIRING DIAGRAM
SAFETY SUGGESTIONS Recommended by Outdoor Power Equipment Institute
1. Know the controls and how to stop quickly read the owners manual.
2. Do not allow children to operate machine; nor adults to operate it without proper instruction.
3. Clear work area of objects which might be picked up and thrown.
4. Disengage all clutches and shift into neutral before starting motor. Keep hands, feet, and clothing away from power driven parts.
5. Do not carry passengers. Keep children and pets a safe distance away.
6. Never direct discharge of any material toward bystanders, nor allow anyone near machine while in operation.
7. Disengage power to attachment (s) and stop motor before leaving operator position.
8. Take precautions when leaving machine un-attended (to avoid accidental starting, rolling away, accidental dropping of any attachment, etc.)
9. Disengage power to any attachment whenever it is not in use, or when traveling from one work area to another.
10. Stay alert for holes and other hidden hazards. Know what is behind you, before backing up.
11. Beware of steep slopes; reduce speed on all side slopes and sharp turns, to prevent tipping or losing control.
12. Don't stop or start suddenly when going uphill or downhill.
13. Use care when pulling loads or using heavy equipment.
14. Watch out for traffic when near roadways.
- 4
15. Handle gasoline with care - it is highly flammable.
a. Use approved gasoline container.
b. Never add gasoline to a running motor -fill tank out of doors wipe up spilled gasoline.
c. Replace gasoline cap securely.
d. Open doors if motor is run in garage -exhaust gases are dangerous.
17. Keep machine in good operating condition and keep safety devices in place. Use guards as instructed in owner's manual.
SPECIFICATIONS
(Specincalions sub/ecl to change withoul nolice.J
Length Overall ....................................... 65 inches Wheelbase ........................................ 45X inches Width Overall ....................................... 36 inches Width at Front Wheels ................................ 33 inches Height .............................................. 40 inches Height to Top of Hood ............................... 35 inches Approx. Shipping Weight .............................. 636 Ibs. Crop Clearance ..................................... 7X inches Frame Clearance ..................................... 13 inches Engine ................................................ 9 H.P. Engine Oil Capacity .................................. 2.5 pints Fuel Capacity ........................................ 6 qua rts
Tires (front) 5.50-8 Pneumatic (16" wheel dia.) Tires (rear) Terra-Type 8.50 x 12" Pneumatic (23" wheel dia.)
Speeds - Infinitely Variable Forward - 0 to 7 M.P.H.
Reverse - 0 to 3X M.P.H. Turning Radius (to outside of outside wheel) ................ 6' 9"
www.MyWheelHorse.com
-
FIG. I
FIG. II FIG. III
-5-
www.MyWheelHorse.com
-
HOOD RELEASE
Fig. IV
-6-
www.MyWheelHorse.com
-
228
218
'" (34 32
"
STEERING & WHEEL ASS/Y.
www.MyWheelHorse.com
-
MAIN FRAME , FEN
-8-
www.MyWheelHorse.com
-
14 ?f!!!.. . 12 @;"~ ~~®
DER & HOOD ASS'Y. -9-
www.MyWheelHorse.com
-
TRACTOR PARTS LIST
(See pages 12 and 13 for Transmission break down and Parts List)
When ordering parts always list Part No. and name of Part.
Item Part No. Item Part No. No. No. Description Req'd. No. No. Description Req'd.
1 7627 Ass'y. Frame 1 59 2179 Rod - Height Control 1
2 7665 Ass'y. Hoodstand 1 60 5280 Knob - Height Control 1
3 6825 Cover - Dust 1 61 3931 Ass'y. Cable - lift 1
4- 908034-4 Bolt Hex %-16 x 1 12 62 932120-4 Pin - Clevis Y.; Dia. 2
5 915663-4 Nut - Elastic Stop %-16 14 63 3926 Hitch 1
6 908017-4 Bolt Hex ~6-18 x % 8 64 3988 Pin 1
7 915112-6 Nut - Nylok ~6-18 6 65 936125 Snap Ring % Shaft 2
8 7446 Pulley 1 66 7781 Ass'y. Battery Box 1
9 909862-5 Set Screw - Nylok ~6- 18 x ~6 3 67 7779 link - Battery Clamp 1
10 937010 Key #6 Woodruff %2 x % 1 68 915111-6 Nut - Nylok y';-20 8 11 908033 Bolt Hex %-16 x % 2 69 7474- Ass'y. lever 1 12 920083-4 lockwasher % Dia. 8 70 920011-4 Washer X SAE 4
13 908033-6 Bolt - Nylok %-16 x % 4 71 5701 "E" Ring X Dia. Shaft 4 14 6110 Ass'y. Tool Box 1 72 6130 Ass'y. Arm & Rod 1
15 908032-4- 80lt Hex %-16 x % 8 73 5666 Bushing 6
16 6465 Hub - Wheel - 5 Bolt 2 74 908003-4 Bolt Hex y';-20 x % 2
17 937022 Key # 15 Woodruff 2 75 915234-4 Nut Jam .Y.;-20 1
18 909554 Set Screw Square Head %-16 x 1 2 76 920081-4 lockwasher .y.; 1 19 915236-4 Nut Hex %-16 Jam 2 77 7432 Ass'y. Handle - Brake 1
20 5638 Axle - Front 1 78 6129 Grip - Handle 2
21 1030 Fitting - Grease 3 79 920009-4 Washer % SAE 6
22 1481 Fitting - Grease 450 1 80 6135 Spring - Brake 1
23 6216 Ass'y. Pin & Plate 1 81 7434 Pulley - Idler 1
24 908015-4 Bolt Hex ~6-18 x X 5 82 7435 Spacer 1
25 920082-4 lockwasher Ji'6 8 83 911400 Bolt - Special %-16 x lX 1
26 5630 Ass'y. Spindle R.H. 1 84 7598 Ass'y. Cam Control Arm 1
27 5631 Ass'y. Spindle l.H. 1 85 6128 Indicator - Speed 1
28 5618 "E" Ring % Dia. 3 86 908001-4 Bolt Hexy';-20 x X 1
29 6396 Support - Steering 1 87 MW-2195 Bushing - Bronze 1
30 6397 Bushing 1 88 6127 Pin - Cam Block 1
31 908035-4 Bolt Hex %-16 x lY.; 3 89 915113-6 Nut - Nylok %-16 6
32 7447 Ass'y. Shaft Upper Steering 1 90 7604 Ass'y. Rod - Cam Pivot 1
33 1085 Collar 2 91 7599 Collar - Friction 1
34 909848-5 Set Screw - Nylok y';-20 x y.; 2 92 7601 Collar - Bracket Pivot 1 35 6469 Ass'y. Steering Shaft lower 1 93 7600 Cone - Friction 1
36 5210 Washer - Shim (.015) 2 94 7602 Spring - Friction 1
37 1278 Washer - Shim (.050) 2 95 7603 Collar - Friction 1
38 932035-4 Cotter Pin 716 x lY.; 1 96 915241-4 Nut %-10 Jam 1
39 6472 Bearing - Side Flange 1 97 937007 Key - Woodruff Ys xX 1 40 5628 Ass'y. Ball Joint R.H. 1 98 6142 Plate - Cam - Neutral 1
41 5629 Ass'y. Ball Joint l.H. 1 99 6143 Spacer - Cam Plate 1
42 915002-6 Nut - Nylok %-24 4 100 5983 Bushing - Nyliner 1
43 6403 Pedal - Neutral 1 101 3765 Washer X Dia. Special 1
44 6254 Bushing 2 102 1230 Spring 1
45 6113 Rod Neutral 1 103 5450 Housing - Control Panel 1
46 933504-4 Hairpin Cotter 1 104 5458 Support - Fuel Tank 1
47 933503-4 Hairpin 7 105 908016-4 Bolt Hex %-18 x % 4 48 933188 Roll Pin 716 x 1 1 106 960152-4 Bolt Whizlock y';-20 x % 4 49 5448 Ass'y. lift lever 1 107 5409 Bushing - Nylon 1
50 4438 Plunger 1 108 5439 Grommet - Rubber 1
51 5449 Rod 1 109 7379 Panel - Complete 1
52 933168 Roll Pin %2 x 1716 1 110 5442 Speed Nut #10-16 4 53 3624 Spring 1 111 926308-4 Screw - Self Tap #10-16 4
54 3578 Guide Plunger 1 112 5417 Tank - Fuel 1
55 3680 Cap 2 113 5459 Clamp - Tank 1
56 1000 Grip - Handle 1 114 5186 Cap - Fuel Tank 1
57 933506-4 Hairpin Cotter Pin 1 115 909059-4 Bolt Round Head Y.;-20 x 1 Y.; 1
58 5640 Quadrant 1 116 915515-4- Nut Square y';-20 1
- 10 -
www.MyWheelHorse.com
-
Item Part No. No.
117 4941
118 7722
119 950153 120 7840 121 908036-4 122 7467 123 943335-4
124 5222 125 5224
126 2873
127 943367-4
128 7443 _ 129 6507
130 5440 131 7638 132 920127-4
133 1364 134 7572 135 7261 136 920159;4 137 5451 138 7262 139 5480 140 5481 141 5483 142 5482 143 915562 144 920078 145 7679 146 7778 147 7664 148 6488 149 7223 150 7226 151 7227 152 7228 153 7075 154 7229 155 7184 156 7185 157 3023 158 7618 159 7680 160 5487 161 5488 162 7574 163 6922 164 909138-4 165 915551-4 166 920079-4 167 908045-4 168 920084-4 169 960175-4 170 7463 171 7454
172 915662-4
173 7455
174 7456
175 900214-4
TRACTOR PARTS LIST
(See pages 12 and 13 for Transmission break down and Parts List)
When ordering parts always list Part No. and name of part.
Description
Ass'y. Filter & Valve Hose - Fuel
Clamp - Corbin 3i'6 Dia. Ass'y. Engine - Lauson Bolt Hex %-16 x I~ Base Engine
Nipple % Pipe x 5 Elbow 90° Cap % Pipe
Muffler Nipple I" Pipe x 2~ Pulley - Engine
Key .);4 x );4 x~ Ass'y. Control - Choke Ass'y. Control - Throttle Lockwasher Ji'6 Shakeproof
Nut - Round Ji'6-18 .Ass'y. Switch Ignition
Nut - Hex Special Ji'6-24 Lockwasher Ji'6 Dia. Insulator - Switch Key Ignition
Ass'y. Cigar Lighter - Complete Ass'y. - Knob & Plub Shell Ass'y. Socket
Nut #8-32 Brass Lockwasher #8 Ass'y. Wire Battery ~. Wiring Harness Wire - Battery to Ground Ass'y. Reflector Housing
Ass'y. Wire & Terminal Spring Bulb (#1156) Lens Screw Self To p #6-32 x % Switch Harness - Headlight
Clip Connector - Three Wire Base - Tail Light Cover - Tail Light Bulb - Tail Light
Ass'y. Wire - Tail Light to Switch Connector - Two Wire Bolt Round Head # 10-32 x% Nut - Hex # 10-32 Lockwasher # 10
Bolt Hex 3i'6-14 x % Lockwasher 3i'6 Dia. Bolt Whizlock %-18 x K Bracket Footrest
Footrest R.H.
Nut ~6-18 Elastic Stop
Footrest L.H.
Bracket - Footrest Anchor
Bolt Carriage ~6-18 x %
No. Req'd.
I
I 2 I 4 I I
I I
I I I I
I I 2 2 I
I I I 2 I I I
I 2 I I I I I I I I 2 I 4 I
I 5 I I I 2 I
I 2 2 2
I I
6 I I
6
I
2
2
Item No.
176
177 178 179 180 181 182
183 184 185
186 187 188 189 190 191 192
193 194 195 196 197
198 199 200 201 202
203 204 205 206 207 208 209 210 211 212 213
214 215
216 217 218 219 220
221 222
223 224 225 226 227
228
229
230
231 232 233
-11-
Part No. Description
7464 Latch - Fender MW-8863 Spring - Fender Latch
5977 7617
7616 908002-4 915661-4
7559 960151-4 7417 4937 5667 7018
7019 7020
7027 7230 5455 5457 6490 5467
5469 933182
5505 5468 915932-4
5466 5522 5438 5437
5432 5433 5434 5435 1004 5637 5635 4999 5636 5512 2844 2816 7420 7469 933215 937014 7468 7561
7568 7476 7477 5604
7421
7634
7633
1813 7478 7436
Bushing - Nyliner
Pin ~6 Rod End Bracket - Fender Latch Screw);4-20 x % Hex Nut );4-20 Elastic Stop
Plate Cover Bolt Whizlock );4-20 x ~ Ass'y. Fender Spacer Bumper Rubber Ass'y. Seat Base
Cushion - Seat Cushion - Back Screw - Whizlock );4-20 x ~ Ass'y. Hood Bracket - Hood Hinge
Bushing - Nylon
Rod - Pivot Lever - Hood Latch
Knob
Roll Pin K6 x % Roller - Rubber Roller - Steel Nut - High Crown # 10-24 Speed Nut - Push On );4 Dia. Rod - Hood Latch Ornament - Hood Speed Nut - Push On Ys Dia. Ass'y. Wheel & Tire Wheel Tire 8:50 x 12 Valve Lug Bolt - Wheel 3i'6-20 Ass'y. Wheel, Tire & Tube Wheel Bearing - Ball Tire 16 x 5.50-8
Tube Washer Hub Cap Steering Wheel Insert Roll Pin );4 x 1);4 Key #9 Woodruff Collar Decal - Charger Decal "9" Decal - Hood Trim R.H. Decal - Hood Trim L.H. Decal - Attachment
Decal - Steering Wheel
Decal - Free Wheeling
Decal - Maintenance Instructions
Tool Pin "V" Belt - Drive Ass'y. Belt Guard
No. Req'd.
I
I
I
I
I
2
2 I
4 I
2 4 1
I
I
5
I
I
2 I
I
1
I 2 2
2
2 1
I
2
2
2
2
2 10 2
2
4 2
2
2
2 I
I
1
I
1
2
2 1
1
1
1
1
I
1
1
1
www.MyWheelHorse.com
-
Transmission
www.MyWheelHorse.com
-
c
,
-
Item No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Part No.
6454
1532
1533
1526
6449
5959
3915
6455
5960
2822
6446
2821
2819
2827
908043-4
920156
2828
6450
6451
2820
933217
2826
6452
5963
5964
5965
936131
937014
5999
908143-4
908038-4
908043-4
915113·6
908034-6
5966
5969
933152
5990
5991
5992
7880
5993
PARTS LIS T
5054 TRANSMISSION (Order No. 5054 for Complete Transmission)
When ordering parts always list Part No. and Name of Part.
Description
Case R.H.
Bea ring - Needle 1" 1.0.
Bearing - Ball 1)1" 1.0.
Bearing - Needle lYe" 1.0.
Seal 1 Ye" 1.0. Seal Brake Shaft)1" 1.0.
Pin - Dowell
Case L.H.
Bearing Needle 1" 1.0.
Case - Differential R.H.
Case - Differential L.H.
Gear - Differential Bull
Gea r - Differential Pinion
Shaft - Differential
Bolt Hex %-16 x 3)1
Washer - Shakeproof %" 1.0.
Washer - Thrust
Axle - Rear - R.H.
Axle - Rear - L.H.
Gear - Axle
Roll Pin 1:1 x )1
Block - Differential
Gear
Gear - 22 Teeth
Gea r 33 Teeth
Shaft 1" Dia.
Snap Ring 1" Shaft
Key #9 Woodruff
Gasket - Case
Bolt Hex %-16 x 5
Bolt Hex %-16 x 2
Bolt Hex %-16 x 3)1
Nut - Nylok %-16
Bolt Hex Nylok %-16 x 1
Assembly - Park Brake
Assembly - Lever Brake
Roll Pin Ye x % Assembly - Filter (Throw-A-Way)
Fitting - Filter
Strainer
Ass'y Hydro-Gear Unit Complete
Support Cam Block
No. Req'd.
1
3
2
2
2
1
2
1
1
1
1
1
2
1
4
4
2
1
1
2
2
2
1
1
1
1
2
2
1
2
3
1
6
3
1
1
1
1
1
1
1
1
Item No.
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
- 13 -
Part No.
911037
6826
972116
5994
933215
970026
5995
909849-5
920229-4
920078·4
5996
5998
909000-4
933196
6155
943346·4
943004
5955
943460
7266
7268
971113
7267
6444
970118
971015
7054
971018
7052
7264
7051
7050
7049
971017
7752
7753
7754
7755
7756
943462
973310
7877
No. Description Req'd.
Screw - Socket Head Cap 1:1-20 x)1 3
Shim
"0" Ring
Arm _. Cam Follower
Roll Pin 1:1 x 11:1
Washer - Seal
Eccentric - Cam Follower
Set Screw - Nylok 1:1-20 x ~6
Washer
Lockwasher # 8
Cam
Plate - Tension
Screw Round Head #8 - 32 x )1
Roll Pin ~6 x 2
Ass'y Dipstick & Filter
Nipple )1 Pipe x 3)1
Coupling )1 Pipe
Gasket - Pump
plug 1:1 Pipe
Valve
Ring - Back Up
"Oil Ring
Plug
2
1
1
1
2
1
1
2
2
1
2
2
1
1
1
1
1
1
1
1
2
1
Ass'y Dampening Valve (With "0" Rings) 2
110" Ring
"O'l Ring
2
2
Ass'y Piston & Sleeve (Matched Ass'y) 2
Spring - Relief Valve
Spring - Relief Valve
Seat Spring
Cone - Relief Valve
Sleeve
"Oil Ring
Plug
Spring - Check Valve
2
2
2
2
2
2
2
7
2
Valve 2
Spring - Charge Pump Relief Valve 1
Cone - Relief Valve 1
Plug )1-14 Pipe 1
"0" Ring 7
Seal 1
www.MyWheelHorse.com
-
ATTACHMENTS AVAILABLE FOR
CHARGER 9 48/1 ROTARY MOWER (5-1481)
42/1 ROTARY MOWER (5-1421)
36/1 ROTARY MOWER (5-1361)
37/1 SNOW THROWER (6-1211)
50/1 SICKLE BAR MOWER (7-1311)
42/1 DOZER BLADE (6-1111)
32/1 DISC (7-1511)
36/1 TILLER (7-1211)
12/1 PLOW (7-1411)
TRAILING CULTIVATOR (7-1711)
TWO SECTION CULTIVATOR (7-1721)
GRADER BLADE (7-1111)
SPI KE TOOTH HARROW (7-1611)
4-WHEEL UTILITY WAGON (7-2111)
2-WHEEL DUMP TRAILER (7-2211)
SPI KED DISC AERATOR (7-2411)
LAWN ROLLER (7-2311)
OPTIONAL ACCESSORIES . FRONT AND REAR WHEEL DISCS (8-0511)
POWER TAKE-OFF (8-3211)
REAR WHEEL WEIGHTS (8-1111)
FRONT WHEEL WEIGHTS (8-1211)
ATTACHMENT CLUTCH (8-3111)
TIRE CHAINS (8-2511)
HYDRAULIC POWER LIFT (8-4111)
DUAL WHEELS (8-0711)
- 14 -
'\ I www.MyW
heelHorse.com
-
ALL SEASON USE
,0
".n~~ "~
, "
- 15 -
www.MyWheelHorse.com
-
Printed in U.S.A. 8-14-67 FORM NO. 396
www.MyWheelHorse.com