NSN Zef

EF - Base Control FunctionHandling

DN9813196Issue 17-0 en29/02/2008

# Nokia Siemens Networks 1 (85)

BSC3153Nokia GSM/EDGE BSS, Rel. BSS13, BSC andTCSM, Rel. S13, Product Documentation, v.1

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended for theuse of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted inany form or means without the prior written permission of Nokia Siemens Networks. Thedocumentation has been prepared to be used by professional and properly trained personnel,and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomescustomer comments as part of the process of continuous development and improvement of thedocumentation.

The information or statements given in this documentation concerning the suitability, capacity, orperformance of the mentioned hardware or software products are given “as is” and all liabilityarising in connection with such hardware or software products shall be defined conclusively andfinally in a separate agreement between Nokia Siemens Networks and the customer. However,Nokia Siemens Networks has made all reasonable efforts to ensure that the instructionscontained in the document are adequate and free of material errors and omissions. NokiaSiemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues whichmay not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NOEVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUTNOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESSOPPORTUNITY OR DATA, THAT MAYARISE FROM THE USE OF THIS DOCUMENT OR THEINFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark ofNokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners,and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2008. All rights reserved.

2 (85) # Nokia Siemens Networks DN9813196Issue 17-0 en

29/02/2008

EF - Base Control Function Handling

Contents

Contents 3

List of tables 4

List of figures 5

Summary of changes 7

EF - BASE CONTROL FUNCTION HANDLING 11

EFC CREATE BASE CONTROL FUNCTION 13

EFD DELETE BASE CONTROL FUNCTION 29

EFM MODIFY BASE CONTROL FUNCTION PARAMETERS 31

EFO OUTPUT BASE CONTROL FUNCTION PARAMETERS 47

EFL OUTPUT BASE CONTROL FUNCTION SYNCHRONIZATIONCONFIGURATION 61

EFS CHANGE BASE CONTROL FUNCTION ADMINISTRATIVESTATE 69

EFT SET BASE CONTROL FUNCTION OUTPUTS 71

EFX SET BASE CONTROL FUNCTION EXTERNAL INPUTPARAMETERS 75

EFR RESET BASE CONTROL FUNCTION 79

EFE MODIFY EXTERNAL INPUT AND OUTPUT TEXT 81

EFP OUTPUT EXTERNAL INPUT AND OUTPUT TEXTS 83

DN9813196Issue 17-0 en29/02/2008


Contents

List of tables


29/02/2008


List of figures

DN9813196Issue 17-0 en29/02/2008


List of figures


29/02/2008


Summary of changes

Changes between document issues are cumulative. Therefore, the latestdocument issue contains all changes made to previous issues.

Changes made between issues 17-0 and 16-1

EFC CREATE BASE CONTROL FUNCTION

New parameters automatic unlock allowed (AU), TRXshutdown timer 2 (NTIM2), TRX shutdown timer 3(NTIM3), Flexi EDGE Abis over IP Ethernet usage(TRS1), Flexi EDGE Additional 2 E1/T1 usage(TRS2), Flexi EDGE TRS Abis Grooming usage(TRS3), and Flexi EDGE TRS Loop Protection usage(TRS4) have been added, and the parameterexplanations, syntax, and execution printout 4 havebeen updated accordingly.

Parameter explanations of TRX shutdown timer(NTIM) and BCCH TRX shutdown timer (BTIM) havebeen updated.

A new execution printout has been added for NokiaFlexi EDGE site type.

EFM MODIFY BASE CONTROL FUNCTIONPARAMETERS

New parameters automatic unlock allowed (AU), TRXshutdown timer 2 (NTIM2), TRX shutdown timer 3(NTIM3), Flexi EDGE Abis over IP Ethernet usage(TRS1), Flexi EDGE Additional 2 E1/T1 usage(TRS2), Flexi EDGE TRS Abis Grooming usage(TRS3), and Flexi EDGE TRS Loop Protection usage(TRS4) have been added, and the parameterexplanations and syntax have been updatedaccordingly.

DN9813196Issue 17-0 en29/02/2008


Summary of changes

Parameter explanations of TRX shutdown timer(NTIM) and BCCH TRX shutdown timer (BTIM) havebeen updated.

Execution printouts for Nokia MetroSite and NokiaUltraSite site types have been updated.

EFO OUTPUT BASE CONTROL FUNCTIONPARAMETERS

Command example 1 has been updated.

Execution printout for Nokia UltraSite has beenupdated and execution printouts for Nokia FlexiEDGE site type have been added. Also the executionprintout abbreviations section has been updated.

Description of abbreviation BL-SWO has beenupdated, and abbreviations BL-CF, BL-CU, and BL-FU have been removed.

EFL OUTPUT BASE CONTROL FUNCTIONSYNCHRONIZATION CONFIGURATION

The execution printout abbreviations section hasbeen updated.

Description of abbreviation BL-SWO has beenupdated, and abbreviations BL-CF, BL-CU, and BL-FU have been removed.



Flexi EDGE optionality was added to the site typeparameter values.


Flexi EDGE optionality was added to the site typeparameter values.


Editorial changes.


ABIS SYNCH and LMU SYNCH were added to theparameter explanation of synchronization mode.


29/02/2008


Connect type parameter was removed.

Flexi EDGE information was added.

EFD DELETE BASE CONTROL FUNCTION

A mention of TRE was added.




EFO OUTPUT BASE CONTROL FUNCTIONPARAMETERS


Reference to Automatic Picocell Planning wasremoved.

ABIS SYNCH and LMU SYNCH were added to theexecution printout abbreviations.

The first execution printout was updated.

EFL OUTPUT BASE CONTROL FUNCTIONSYNCHRONIZATION CONFIGURATION

Reference to Automatic Picocell Planning wasremoved.

EFE MODIFY EXTERNAL INPUT AND OUTPUT TEXT

Parameter description of text string was updated.

EFX SET BASE CONTROL FUNCTION EXTERNALINPUT PARAMETERS


EFR RESET BASE CONTROL FUNCTION


DN9813196Issue 17-0 en29/02/2008


Summary of changes


29/02/2008


EF - BASE CONTROL FUNCTION HANDLING

With the commands of the EF command group you can create and deletea BCF object. In addition, you can change and output the parameters, theadministrative state of the BCF object and the states of the externaloutputs in the BSS Radio Network Configuration Database (BSDATA). Youcan also reset the BTS site or its Operation and Maintenance Unit (OMU).

In addition, with the commands of this command group you can attach atext string to external inputs and outputs of the BCF and modify the textstring. You can also set external input parameters of the BCF.

Menu of the command group:

BASE CONTROL FUNCTION HANDLING COMMANDS

? ..... DISPLAY MENU

C: ..... CREATE BASE CONTROL FUNCTION

D: ..... DELETE BASE CONTROL FUNCTION

M: ..... MODIFY BASE CONTROL FUNCTION PARAMETERS

O: ..... OUTPUT BASE CONTROL FUNCTION PARAMETERS

L: ..... OUTPUT BASE CONTROL FUNCTION SYNCHRONIZATION CONFIGURATION

S: ..... CHANGE BASE CONTROL FUNCTION ADMINISTRATIVE STATE

T: ..... SET BASE CONTROL FUNCTION OUTPUTS

X: ..... SET BASE CONTROL FUNCTION EXTERNAL INPUT PARAMETERS

R: ..... RESET BASE CONTROL FUNCTION

E: ..... MODIFY EXTERNAL INPUT AND OUTPUT TEXT

P: ..... OUTPUT EXTERNAL INPUT AND OUTPUT TEXTS

Z; ..... RETURN TO MAIN LEVEL

DN9813196Issue 17-0 en29/02/2008


EF - BASE CONTROL FUNCTION HANDLING


29/02/2008


EFC CREATE BASE CONTROL FUNCTIONFunction With this command you create a BCF object in the BSS Radio Network

Configuration Database (BSDATA).

Parameters BCF identification, site type: autoconfigure <option>, bit rate <option>,automatic unlock allowed, D-channel link set number, D-channel link setname, reference BCF identification, RX difference limit: identification oftest equipment: BTS battery backup procedure <option>, TRX shutdowntimer <option>, TRX shutdown timer 2 <option>, TRX shutdown timer 3<option>, BCCH TRX shutdown timer <option>: clock source, add BCF tochain, synch enabled, master clock BCF identification: Flexi EDGE Abisover IP Ethernet usage <option>, Flexi EDGE Additional 2 E1/T1 usage<option>, Flexi EDGE TRS Abis Grooming usage <option>, Flexi EDGETRS Loop Protection usage <option>;

Syntax

EFC: <BCF identification>,

<site type> :

[ AC = <autoconfigure> <option> | N def |

BR = <bit rate> <option> |

AU = <automatic unlock allowed> | T def |

DNBR = <D-channel link set number> |

DNAME = <D-channel link set name> |

REF = <reference BCF identification> |

RXDL = <RX difference limit> | 10 def | ] ... :

[ TEST = <identification of test equipment> | NOT def ] :

[ BBU = <BTS battery backup procedure> | ALL def |

NTIM = <TRX shutdown timer> | 0 def |

NTIM2 = <TRX shutdown timer 2> <option> | 0 def |

NTIM3 = <TRX shutdown timer 3> <option> | 0 def |

BTIM = <BCCH TRX shutdown timer> | 0 def ] ... <option> :

[[ CS = <clock source> | NOT USED def |

ADD = <add BCF to chain> ... |

SENA = <synch enabled> | F def ] ... |

DN9813196Issue 17-0 en29/02/2008



[ MCBCF = <master clock BCF identification> ]] :

[ TRS1 = <Flexi EDGE Abis over IP Ethernet usage> <option> | 0 def |

TRS2 = <Flexi EDGE Additional 2 E1/T1 usage> <option> | 0 def |

TRS3 = <Flexi EDGE TRS Abis Grooming usage> <option> | 0 def |

TRS4 = <Flexi EDGE TRS Loop Protection usage> <option> | 0 def ] ... ;

Parameterexplanations

BCF identification

With this parameter you identify the BCF with a decimal number. The valuerange depends on the BSC hardware configuration and the correspondingoptions.

The parameter is obligatory.

site type

With this parameter you identify the type of the BTS site. The alternativesare:

B: Nokia 2nd generation

D: Nokia Talk-family

F: Nokia PrimeSite

C: Nokia MetroSite

I: Nokia InSite

P: Nokia UltraSite

E: <option> Nokia Flexi EDGE


autoconfigure <option>

With this parameter you define whether the BCF is created to beautoconfigured.

The values are:

Parameter Value Explanation

AC = Y BCF is created to beautoconfigured.

N BCF is not created to beautoconfigured.


29/02/2008


You can give this parameter only if the site type is Nokia MetroSite, NokiaInSite, Nokia UltraSite, or Nokia Flexi EDGE.

The default value is N.

automatic unlock allowed

With this parameter you define whether the automatic unlock is allowed forthe BCF or not.

The values are:


AU = T Automatic unlock isallowed.

F Automatic unlock is notallowed.

The default value is T.

You can give this parameter only if the site type is Nokia Flexi EDGE.

bit rate <option>

BR = decimal number

With this parameter you define the bit rate of the D-channel O&M signallinglink of the BCF.

The values are 8, 16, 32, or 64 kbps.

This parameter is obligatory if the BCF is created to be autoconfigured (thevalue of parameter autoconfigure is Y).

If the BCF is not created to be autoconfigured, you cannot give thisparameter.

D-channel link set number

DNBR = decimal number

With this parameter you identify the D-channel link set number of the BTSsite O&M link. You can give only one of the parameters DNBR and DNAMEin the same command.

DN9813196Issue 17-0 en29/02/2008



You cannot give the D-channel link set number for the Nokia PrimeSite.

You cannot give this parameter if the BCF is created to be autoconfigured.

D-channel link set name

DNAME = text string

With this parameter you identify the D-channel link set name of the BTSsite O&M link. The name can contain 1 to 5 characters. You can give onlyone of the parameters DNBR and DNAME in the same command.

You cannot give the D-channel link set name for the Nokia PrimeSite.

This parameter is obligatory if the BCF is created to be autoconfigured (thevalue of parameter autoconfigure is Y).

If the BCF is created to be autoconfigured, the D-channel O&M signallinglink cannot exist because it is created during the BCF creation.

reference BCF identification

REF = decimal number

With this parameter you identify the BCF that is used to obtain the externalinput and output values. The value range depends on the BSC hardwareconfiguration and the corresponding options.

If a reference BCF is not used, the system uses the default values for therequired BCF parameters during the creation.

The parameter is allowed only for the Nokia MetroSite, Nokia UltraSite,and Nokia Flexi EDGE site types.

RX difference limit

RXDL = decimal number

With this parameter you define the value limit for activating the RX alarm.The BTS compares the main and diversity antenna RX levels and if thedifference is below this limit, an RX alarm is set.

The values range from 3 to 64 dB.

The default value is 10 dB.


29/02/2008


For site types Nokia UltraSite, Nokia MetroSite, Nokia 2nd generation, andNokia Flexi EDGE the value 64 dB indicates that no RX alarms are set.

The parameter is not available for the Nokia InSite site type.

identification of test equipment

With this parameter you define the test equipment connected to the BCF.The values are:


TEST = STM Site Test Monitor unit

RFTE Radio Frequency TestEquipment

NOT no test equipment

The default value is that no test equipment is connected to the BCF.

Value RFTE is allowed only for the Nokia 2nd generation site type.

The parameter is available only for the Nokia 2nd generation and NokiaTalk-family site types.

BTS battery backup procedure <option>

With this parameter you define what type of BTS battery backup procedureis used. The procedure is executed when the mains power goes down atthe BTS site and there is a battery backup unit.

The values are:


BBU = ALL Transmission equipmentand all the TRXs are leftalive.

BCCH Transmission equipmentand only the BCCH TRXare left alive.

NONE Only transmissionequipment is left alive.

The default value is that all the TRXs and transmission equipment are leftalive.

DN9813196Issue 17-0 en29/02/2008



The parameter is not available for the Nokia PrimeSite or Nokia InSite sitetypes.

TRX shutdown timer <option>

NTIM = decimal number

With this parameter you define the time period after which shutdown group1 TRXs are powered down. The time starts after the TRX Shutdown Timer2 has expired. The parameter is valid only if the BTS Battery BackupProcedure (BBU) parameter has value BCCH or NONE.

The values range from 0 to 600 minutes. The default value is 0.


TRX shutdown timer 2 <option>

NTIM2 = decimal number



The parameter is not available for the Nokia PrimeSite, Nokia InSite, orNokia 2nd generation site types.



With this parameter you define the time period after which shutdown group3 TRXs are powered down. The parameter is valid only if the BTSBattery Backup Procedure (BBU) parameter has value BCCH orNONE.



BCCH TRX shutdown timer <option>


29/02/2008


BTIM = decimal number

With this parameter you define the time period after which shutdown group0 TRXs are powered down. The time starts after the TRX Shutdown Timer1 has expired. The parameter is valid only if the BTS Battery BackupProcedure (BBU) parameter has value BCCH or NONE. Also the BCCHTRXs are powered down when the BTS Battery Backup Procedure(BBU) parameter has value NONE.



clock source

With this parameter you define the clock source of the master clock BCF orthe independent mode BCF. When creating the master clock BCF, theclock source must be BCF, LMU, or LAB. Use LMU and LAB values whenBSS synchronisation is in use.

The values you can give are:


CS = BCF master clock BCF

LMU Location Measurement Unit

LAB Location Measurement Unitwith Abis recovery (LMU-ABIS)

NONE remove clock source

PCM independent mode

The default value is NOT USED.

The parameter is not available for the Nokia 2nd generation, NokiaPrimeSite, or Nokia InSite site types.

add BCF to chain

ADD = decimal number

DN9813196Issue 17-0 en29/02/2008



With this parameter you define BCFs to a chain under the master clockBCF. The value range depends on the BSC hardware configuration andthe corresponding options. You can enter several values at the same timeby using the grouping character &. You can define at the most 8 BCFs to achain under the master clock BCF. The definition is done when creatingthe master clock BCF.


synch enabled

With this parameter you enable the synchronisation of the BCF chain orthe independent mode BCF. The enabling of the synchronisation ispossible only when creating the master clock BCF or the independentmode BCF.

The values are:


SENA = T Synchronisation enabled.

F Synchronisation disabled.

The default value is F.


master clock BCF identification

MCBCF = decimal number

With this parameter you add the BCF to a chain. The value range dependson the BSC hardware configuration and the corresponding options. Thedefinition is done when creating the BCF which is added to a chain under amaster clock BCF.


synchronization mode

SM (non-modifiable)

This parameter describes the synchronisation mode of the BCF.


29/02/2008


The values are:


SM = UNSYNCH unsynchronised

SYNCH synchronised

ABIS SYNCH BSS synchronised usingAbis

LMU SYNCH BSS synchronised usingLocation Measurement Unit

The value SYNCH is shown in printouts when the synchronisation of theBCF or the BCF chain is enabled and the BCF is working in thesynchronised mode.

Flexi EDGE Abis over IP Ethernet usage <option>

With this parameter you enable Flexi EDGE Abis over IP/ Ethernet in theBCF.

The values are:


TRS1 = 0 Flexi EDGE Abis over IP/Ethernet not in use.

1 Flexi EDGE Abis over IP/Ethernet in use.

The default value is 0.

This parameter is valid only for Nokia Flexi EDGE site type.

Flexi EDGE Additional 2 E1/T1 usage <option>

With this parameter you enable Flexi EDGE Additional 2 E1/T1 in the BCF.

The values are:


TRS2 = 0 2 E1/T1 free interfaces inuse.

1 Additional 2 E1/T1interface in use.

DN9813196Issue 17-0 en29/02/2008




2 2 additional 2 E1/T1interfaces in use.




Flexi EDGE TRS Abis Grooming usage <option>

With this parameter you enable Flexi EDGE TRS Abis Grooming in theBCF.

The values are:


TRS3 = 0 Flexi EDGE TRS AbisGrooming not in use.

1 Flexi EDGE TRS AbisGrooming in use.



Flexi EDGE TRS Loop Protection usage <option>

With this parameter you enable Flexi EDGE TRS Loop Protection in theBCF.

The values are:


TRS4 = 0 Flexi EDGE TRS LoopProtection not in use.

1 Flexi EDGE TRS LoopProtection in use.




29/02/2008


Examples 1. Create a BCF whose identification number is 127 and site type isNokia PrimeSite.

ZEFC:127,F;

2. Create a BCF whose identification number is 128, D-channel link setnumber is 5, and site type is Nokia 2nd generation.

ZEFC:128,B:DNBR=5;

3. Create a BCF whose identification number is 12, D-channel link setname is FU11, and site type is Nokia Talk-family. The test equipmentSTM is connected to it and no TRXs are left alive after timers haveexpired on the BTS battery backup procedure. The BCF is createdas an independent mode BCF and the synchronisation is enabled.

ZEFC:12,D:DNAME=FU11:TEST=STM:BBU=NONE,NTIM=30,BTIM=60:CS=PCM,SENA=T;

4. Create a BCF whose identification number is 120, D-channel link setname is AC1, and site type is Nokia MetroSite. The reference BCF-121 is used to obtain the external input and output parameters. TheBCF is created to be autoconfigured and the bit rate of the O&Msignalling link is set to 64 kbps. The BCF is created as the masterclock BCF and the clock source is defined to LMU. BCFs 121 and122 are added to the chain under the master clock BCF.

ZEFC:120,C:AC=Y,BR=64,DNAME=AC1,REF=121:::CS=LMU,ADD=121&122;

5. Create a BCF whose identification number is 125, D-channel link setname is AC2, and site type is Nokia UltraSite. The BCF is created tobe autoconfigured and the bit rate of the O&M signalling link is set to16 kbps. The BCF is added to the chain under the master clock BCFnumber 110.

ZEFC:125,P:AC=Y,BR=16,DNAME=AC2:::MCBCF=110;

Additionalinformation

After you have created a BCF its administrative state is LOCKED and itsexternal outputs are in the OFF state.

In addition, the default values are set for the BCF's external inputparameters. The default parameter values are:

PARAMETER ABBR. VALUE

master clock trx MCT 0 (not synchronised)

external synchronisation source ESS 2 (PCM external)

route ROU NOT (not reported)

polarity POL OPEN (open)

severity SEV AL1 (lowest alarm level)

text ID TID 0 (text not defined)

DN9813196Issue 17-0 en29/02/2008



Executionprintouts

The printout of command example 1 is the following:

BSC BSC-LAB 2007-10-10 13:55:06

BASE CONTROL FUNCTION BCF-0127 CREATED

SITE TYPE ............................ F - PRIMESITE

ADMINISTRATIVE STATE ................. LOCKED

OPERATIONAL STATE .................... BL-USR

RX DIFFERENCE LIMIT ..........(RXDL).. 10 dB

MASTER CLOCK TRX .............(MCT)... 0 (NOT SYNCHRONISED)

EXTERNAL SYNC SOURCE .........(ESS)... 2 (PCM EXTERNAL)

DEFAULT BCF SOFTWARE BUILD ATTACHED

COMMAND EXECUTED


BSC BSC-LAB 2007-10-10 13:54:32


SITE TYPE ............................ B - 2ND GEN



D-CHANNEL LINK SET 5 ............. FU2 WO-EX

OUTPUT 1 .......................... OFF

OUTPUT 2 .......................... OFF

OUTPUT 3 .......................... OFF

OUTPUT 4 .......................... OFF

OUTPUT 5 .......................... OFF

OUTPUT 6 .......................... OFF


TEST EQUIPMENT ...............(TEST).. --

BTS BATTERY BACKUP PROCEDURE .(BBU)... ALL

TRX SHUTDOWN TIMER ...........(NTIM).. 0 min

BCCH TRX SHUTDOWN TIMER ......(BTIM).. 0 min


COMMAND EXECUTED

The printout of command example 4 for MetroSite is the following:

BSC BSC-LAB 2007-10-10 14:14:32


BCF IS WAITING FOR AUTOCONFIGURATION


29/02/2008


SITE TYPE ............................ C - METROSITE



D-CHANNEL LINK SET 1 ............. AC1 BL-SY

OUTPUT 1 ....................... ON TEXT ID 2

ADDITIONAL COOLER FAN

OUTPUT 2 ........................ ON TEXT ID -

OUTPUT 3 ........................ OFF TEXT ID -


INPUT 1 ..............ROUTE: ACT

POLARITY: OPEN SEVERITY: *** TEXT ID 99

RECTIFIER MAJOR ALARM

INPUT 2 ..............ROUTE: NOT REPORT

POLARITY: OPEN SEVERITY: * TEXT ID -




















TRX SHUTDOWN TIMER 2 .........(NTIM2). 0 min



MASTER CLOCK BCF .............(MCBCF). 0120

CHAIN BCFS AFTER MASTER CLOCK BCF:

BCF-0121

BCF-0122

CLOCK SOURCE .................(CS).... LMU

SYNCHRONIZATION ENABLED ......(SENA).. F

SYNCHRONIZATION MODE .........(SM).... UNSYNCH


COMMAND EXECUTED

The printout of command example 4 using site type E (Flexi EDGE) is thefollowing:

DN9813196Issue 17-0 en29/02/2008



BSC BSC-LAB 2007-10-10 14:14:32


BCF IS WAITING FOR AUTOCONFIGURATION

SITE TYPE ............................ E - FLEXI EDGE



D-CHANNEL LINK SET 1 ............. AC1 BL-SY

OUTPUT 1 ....................... ON TEXT ID 2


OUTPUT 2 ........................ ON TEXT ID -































CHAIN BCFS AFTER MASTER CLOCK BCF:

BCF-0121

BCF-0122

CLOCK SOURCE .................(CS).... LMU



AUTOMATIC UNLOCK ALLOWED .....(AU).... T

FACCH LAPDM T200 .............(T200F). 0 (BCF PREDEFINED VALUES)

SDCCH LAPDM T200 .............(T200S). 0 (BCF PREDEFINED VALUES)

ABIS OVER IP ETHERNET USAGE...(TRS1).. 0 (NOT IN USE)

ADDITIONAL 2 E1/T1 USAGE......(TRS2).. 0 (NOT IN USE)


29/02/2008


TRS ABIS GROOMING USAGE.......(TRS3).. 0 (NOT IN USE)

TRS LOOP PROTECTION USAGE.....(TRS4).. 0 (NOT IN USE)


COMMAND EXECUTED

Semantic errormessages

/*** BCF IS NOT DEFINED TO MASTER CLOCK BCF ***/

The BCF, which you have attempted to define as the master clock BCF ofthe created BCF, is not a master clock BCF.

/*** CHAIN BCF NOT FOUND IN BSC DATABASE ***/

The BCF, which you have attempted to add to the chain under the masterclock BCF, does not exist.

In addition, the general semantic error messages of the MML commandsare output. For more information, see General Notice Messages of MMLSession.

Execution errormessages

/*** ATTACHMENT OF DEFAULT BCF SOFTWARE BUILD FAILED ***/

The BCF creation was successful but attaching the software build failed.

/*** BCSU UPDATE ERROR ***/

The creation was successful but updating one or more BCSUs failed. Afterthis message, a list of failed BCSU updates is output, for example, in thefollowing form:

/*** BCSU-05 NOT UPDATED ***/


In addition, the general execution error messages of the MML commandsare used. For more information, see Radio Network Administration andGeneral Error Messages of System.

DN9813196Issue 17-0 en29/02/2008




29/02/2008


EFD DELETE BASE CONTROL FUNCTIONFunction With this command you delete a BCF object from the radio network (RNW)

database. A BCF object can be deleted only if there are no BTSs or TREsunder it.

Parameters BCF identification;

Syntax EFD: <BCF identification>;


BCF identification


Examples 1. Delete the BCF object whose identification number is 128.

ZEFD:128;

Executionprintouts

The execution printout of command example 1 is the following:

BSC BSC-LAB 2007-10-10 13:54:32

BASE CONTROL FUNCTION BCF-0128 DELETED

COMMAND EXECUTED


In error conditions, the general semantic error messages of the MMLcommands are output. For more information, see General NoticeMessages of MML Session.



DN9813196Issue 17-0 en29/02/2008


EFD DELETE BASE CONTROL FUNCTION

The deletion was successful but updating one or more BCSUs failed. Afterthis message, a list of failed BCSU updates is output, for example, in thefollowing form:





29/02/2008


EFM MODIFY BASE CONTROL FUNCTIONPARAMETERSFunction With this command you modify the BCF object's parameters in the BSS

Radio Network Configuration Database (BSDATA). The D-channel link setnumber must be created before this command can be used. If the BCF siteis synchronised, the master clock TRX must be defined under the BCF thatyou want to modify.

The command is not available for the Nokia InSite if it is waiting forautoconfiguration.

Parameters BCF identification: site type, D-channel link set number, D-channel link setname, RX difference limit, identification of test equipment, master clockTRX, external synchronisation source, automatic unlock allowed, BTSbattery backup procedure <option>, TRX shutdown timer <option>, TRXshutdown timer 2 <option>, TRX shutdown timer 3 <option>, BCCH TRXshutdown timer <option>, clock source, synch enabled, add BCF to chain,remove BCF from chain, text ID of the output 1, text ID of the output 2, textID of the output 3, text ID of the output 4, text ID of the output 5, text ID ofthe output 6: FACCH LAPDm T200, SDCCH LAPDm T200: Flexi EDGEAbis over IP Ethernet usage <option>, Flexi EDGE Additional 2 E1/T1usage <option>, Flexi EDGE TRS Abis Grooming usage <option>, FlexiEDGE TRS Loop Protection usage <option>;

Syntax

EFM: <BCF identification> :

( [ TYPE = <site type> |

DNBR = <D-channel link set number> |

DNAME = <D-channel link set name> |

RXDL = <RX difference limit> |

TEST = <identification of test equipment> |

MCT = <master clock TRX> |

ESS = <external synchronisation source> |

AU = <automatic unlock allowed> |

BBU = <BTS battery backup procedure> <option> |

DN9813196Issue 17-0 en29/02/2008


EFM MODIFY BASE CONTROL FUNCTION PARAMETERS

NTIM = <TRX shutdown timer> <option> |

NTIM2 = <TRX shutdown timer 2> <option> |

NTIM3 = <TRX shutdown timer 3> <option> |

BTIM = <BCCH TRX shutdown timer>

CS = <clock source> |

SENA = <synch enabled> |

ADD = <add BCF to chain> ... |

REM = <remove BCF from chain> ... |

OUT1 = <text ID of the output 1> |





OUT6 = <text ID of the output 6> ] ... ) :

[ T200F = <FACCH LAPDm T200> |

T200S = <SDCCH LAPDm T200> ] :

[ TRS1 = <Flexi EDGE Abis over IP Ethernet usage> <option> |

TRS2 = <Flexi EDGE Additional 2 E1/T1 usage> <option> |

TRS3 = <Flexi EDGE TRS Abis Grooming usage> <option> |

TRS4 = <Flexi EDGE TRS Loop Protection usage> <option> ] ... );


BCF identification



site type

With this parameter you modify the BTS site type. The following BTS sitetype modifications are allowed:

. from Nokia 2nd generation to Nokia Talk-family,

. from Nokia 2nd generation to Nokia UltraSite,

. from Nokia Talk-family to Nokia 2nd generation,

. from Nokia Talk-family to Nokia UltraSite,

. from Nokia Talk-family to Nokia Flexi EDGE, and

. from Nokia UltraSite to Nokia Flexi EDGE.

The alternatives are:


29/02/2008



TYPE = B Nokia 2nd generation

D Nokia Talk-family

P Nokia UltraSite

E <option> Nokia Flexi EDGE

Tip

Check the BCF hardware database and the BCF software build.

Note

The base transceiver station (BTS) site type modification deletes thetransmission equipment under the modified base control function(BCF). The transmission equipment is updated automatically aftersome time. If the update needs to be faster, use the QUF MMLcommand for the BTSs with hardware database or the QWA MMLcommand for the BTSs without hardware database.

For more information, see .

Note

The operation and maintenance unit (OMU) link of the base controlfunction (BCF) cannot be in working (WO) state when the basetransceiver station (BTS) site type is modified to Nokia UltraSite orNokia Flexi EDGE.

D-channel link set number

DNBR = decimal number

With this parameter you modify the D-channel link set number of the BTSsite O&M link. You can give only one of the parameters DNBR and DNAMEin the same command.

This parameter cannot be given if the BCF is waiting for autoconfiguration.

DN9813196Issue 17-0 en29/02/2008



For the Nokia PrimeSite, you cannot modify the D-channel link set number.

D-channel link set name

DNAME = identifier

With this parameter you modify the D-channel link set name of the BTSsite O&M link. The name can contain 1 to 5 characters. You can give onlyone of the parameters DNBR and DNAME in the same command.

This parameter cannot be given if the BCF is waiting for autoconfiguration.

For the Nokia PrimeSite, you cannot modify the D-channel link set name.

RX difference limit

RXDL = decimal number

With this parameter you define the value limit for activating the RX alarm.The BTS compares the main and diversity antenna RX levels and if thedifference is below this limit, an RX alarm is set.

The values range from 3 to 64 dB.

For site types Nokia UltraSite, Nokia MetroSite, Nokia 2nd generation, andNokia Flexi EDGE the value 64 dB indicates that no RX alarms are set.

The parameter is not available for the Nokia InSite site type.

identification of test equipment

With this parameter you define the test equipment connected to the BCF.

The parameters are:


TEST = STM Site Test Monitor unit

RFTE Radio Frequency TestEquipment

NOT no test equipment

Value RFTE is allowed only for the Nokia 2nd generation site type.


29/02/2008


The parameter is available only for the Nokia 2nd generation and NokiaTalk-family site types.

master clock TRX

MCT = decimal number

With this parameter you define the master clock TRX for the NokiaPrimeSite. The values range from 0 to 16. Value 0 indicates that the site isnot synchronised (stand-alone). Values 1 - 16 identify the master clockTRX (and indicate that the site is synchronised). If there is more than oneTRX in the site, the site must be synchronised (MCT≠0).

When you modify the master clock TRX, the BCF must be locked.

The parameter is only available for the Nokia PrimeSite.

external synchronisation source

With this parameter you define the synchronisation source of the masterclock TRX for a synchronised site. If the site is not synchronised but stand-alone, the parameter defines a synchronisation source for all the TRXs inthe site.

The values are:


ESS = 0 BTS internal

2 PCM external

3 other external

When you modify the external synchronisation source, the BCF must belocked.

The parameter is only available for the Nokia PrimeSite.

automatic unlock allowed

With this parameter you define whether the automatic unlock is allowed forthe BCF or not.

The values are:

DN9813196Issue 17-0 en29/02/2008




AU = T Automatic unlock isallowed.

F Automatic unlock is notallowed.

You can give this parameter only if the site type is Nokia Flexi EDGE.

BTS battery backup procedure <option>

With this parameter you modify what type of BTS battery backupprocedure is used. The procedure is executed when the mains power goesdown at the BTS site and the battery backup unit exists.

The values are:


BBU = ALL Transmission equipmentand all the TRXs are leftalive.

BCCH Transmission equipmentand only the BCCH TRXare left alive.

NONE Only transmissionequipment is left alive.


TRX shutdown timer <option>

NTIM = decimal number


The values range from 0 to 600 minutes.




29/02/2008








With this parameter you define the time period after which shutdown group3 TRXs are powered down. The parameter is valid only if the BTSBattery Backup Procedure (BBU) parameter has value BCCH orNONE.



BCCH TRX shutdown timer <option>

BTIM = decimal number

With this parameter you define the time period after which shutdown group0 TRXs are powered down. The time starts after the TRX Shutdown Timer1 has expired. The parameter is valid only if the BTS Battery BackupProcedure (BBU) parameter has value BCCH or NONE. Also the BCCHTRXs are powered down when the BTS Battery Backup Procedure(BBU) parameter has value NONE.



clock source

DN9813196Issue 17-0 en29/02/2008



With this parameter you define the clock source of the master clock BCF orthe independent mode BCF. The clock source of the master clock BCFmust be BCF, LMU, or LAB. You can remove the master clock BCF and allBCFs from the chain or the independent mode BCF from independentmode by defining the clock source to NONE.

You can modify the value of this parameter online from LMU to LAB. If theBCF chain is not in 'ABIS SYNCH' mode, you can modify the value of thisparameter from LAB to LMU online. Otherwise the parameter modificationrequires that the BCF's synch enabled (SENA) parameter has the valueN or that the BCF is locked. In the case of a BCF chain, all the BCFs in thechain must be locked.

The values are:


CS = BCF master clock BCF

LMU Location Measurement Unit

LAB Location Measurement Unitwith Abis recovery (LMU-ABIS)

PCM independent mode

NONE remove clock source


synch enabled

With this parameter you enable and disable the synchronisation of theBCF chain or the independent mode BCF. Enabling and disabling thesynchronisation is possible only when modifying the master clock BCF orthe independent mode BCF.

When you enable the synchronisation, the BCF must be locked.

When you disable the synchronisation, the BCF, and in the case of a BCFchain, all the BCFs in the chain must be locked.

The values are:




29/02/2008





add BCF to chain

ADD = decimal number

With this parameter you add BCFs to the chain under the master clockBCF. The value range depends on the BSC hardware configuration andthe corresponding options. You can enter several values at the same timeby using the grouping character &. You can define at the most 8 BCFs to achain under a master clock BCF. The definition is done when modifying themaster clock BCF.

You can add a slave BCF to synch enabled BCF chain if the slave BCF islocked.


remove BCF from chain

REM = decimal number

With this parameter you remove BCFs from a chain. The value rangedepends on the BSC hardware configuration and the correspondingoptions. You can enter several values at the same time by using thecharacter &. The definition is done when modifying the master clock BCF.

You can remove a slave BCF from synch enabled BCF chain if the slaveBCF is locked.


text ID of the output from 1 to 6

OUT1...OUT6 = decimal number

With this parameter you define the text ID for the external output. Thevalues range from 1 to 200.

To remove the output's text ID, enter the value 0 (0 = text not defined).

DN9813196Issue 17-0 en29/02/2008



The parameter is only available for the Nokia MetroSite, Nokia UltraSite,and Nokia Flexi EDGE.

Nokia MetroSite has 4 external outputs, whereas Nokia UltraSite andNokia Flexi EDGE have 6 external outputs.

FACCH LAPDm T200

T200F = decimal number

With this parameter you define an LAPDm for the supervision of theFACCH message transfer from the BTS to the mobile. The values rangefrom 200 to 1260 ms, in20 ms steps.

This parameter is supported only by Nokia Talk-family, Nokia UltraSite,and Nokia Flexi EDGE site types.

SDCCH LAPDm T200

T200S = decimal number

With this parameter you define an LAPDm for the supervision of theSDCCH message transfer from the BTS to the mobile. The values rangefrom 220 to 1260 ms, in 20 ms steps.

This parameter is supported only by Nokia Talk-family, Nokia UltraSite,and Nokia Flexi EDGE site types.

Flexi EDGE Abis over IP Ethernet usage <option>

With this parameter you enable Flexi EDGE Abis over IP/ Ethernet in theBCF.

The values are:


TRS1 = 0 Flexi EDGE Abis over IP/Ethernet not in use.

1 Flexi EDGE Abis over IP/Ethernet in use.


Flexi EDGE Additional 2 E1/T1 usage <option>


29/02/2008


With this parameter you enable Flexi EDGE Additional 2 E1/T1 in the BCF.

The values are:


TRS2 = 0 2 E1/T1 free interfaces inuse.

1 Additional 2 E1/T1interface in use.




Flexi EDGE TRS Abis Grooming usage <option>

With this parameter you enable Flexi EDGE TRS Abis Grooming in theBCF.

The values are:


TRS3 = 0 Flexi EDGE TRS AbisGrooming not in use.

1 Flexi EDGE TRS AbisGrooming in use.


Flexi EDGE TRS Loop Protection usage <option>

With this parameter you enable Flexi EDGE TRS Loop Protection in theBCF.

The values are:


TRS4 = 0 Flexi EDGE TRS LoopProtection not in use.

DN9813196Issue 17-0 en29/02/2008




1 Flexi EDGE TRS LoopProtection in use.


Examples 1. In BCF-128, modify the D-channel link set number to 10.

ZEFM:128:DNBR=10;

2. In BCF-12, modify the test equipment information to RFTE.

ZEFM:12:TEST=RFTE;

3. In BCF-12, modify the D-channel link set number to 22, set the BTSbattery backup procedure to BCCH and BCCH TRX shutdown timerto 20 minutes, and set the test equipment information to RFTE.

ZEFM:12:DNBR=22,TEST=RFTE,BBU=BCCH,BTIM=20;

4. In BCF-101 of Nokia PrimeSite, modify the site's master clock TRXto TRX 2 and external synchronisation source to PCM external.

ZEFM:101:MCT=2,ESS=2;

5. In BCF-120, modify the text ID number of output 2 to value 5.

ZEFM:120:OUT2=5;

6. In BCF-130, define the BCF as the master clock BCF and set theclock source to BCF, enable the synchronisation of the chain andadd BCFs 131 and 132 to the chain.

ZEFM:130:CS=BCF,SENA=T,ADD=131&132;

7. Remove master clock BCF number 130 and all BCFs from the chainunder the master clock BCF.

ZEFM:130:CS=NONE;

8. Remove BCFs 108, 109, and 110 from the chain under the masterclock BCF number 105.

ZEFM:105:REM=108&109&110;

Executionprintouts

The printout of the command ZEFM:128:TYPE=B,DNBR=43,TEST=NOT;for Nokia 2nd generation is the following:

BSC BSC-LAB 2007-10-10 13:54:32

BASE CONTROL FUNCTION BCF-0128 MODIFIED

SITE TYPE ............................ B - 2ND GEN


29/02/2008


D-CHANNEL LINK SET 43 ............. FU21







COMMAND EXECUTED

The printout of the command ZEFM:127:MCT=1,ESS=2; for NokiaPrimeSite is the following:

BSC BSC-LAB 2007-10-10 13:55:37




MASTER CLOCK TRX .............(MCT)... 1


COMMAND EXECUTED

The printout of the command ZEFM:120:OUT2=5; for Nokia MetroSite isthe following:

BSC BSC-LAB 2007-10-10 15:16:31


SITE TYPE ............................ C - METROSITE


OUTPUT 1 ........................ ON TEXT ID 2


OUTPUT 2 ........................ ON TEXT ID 5

MAST WARNING LIGHTS









MASTER CLOCK BCF .............(MCBCF). ––

CLOCK SOURCE .................(CS).... PCM

SYNCHRONIZATION ENABLED ......(SENA).. T

SYNCHRONIZATION MODE .........(SM).... SYNCH

COMMAND EXECUTED

DN9813196Issue 17-0 en29/02/2008



The printout of the command ZEFM:100:RXDL=20; for Nokia UltraSite isthe following:

BSC BSC-LAB 2007-10-10 05:08:37


SITE TYPE ............................ P - ULTRASITE


OUTPUT 1 ....................... OFF TEXT ID -












MASTER CLOCK BCF .............(MCBCF). ––

CLOCK SOURCE .................(CS).... ––



FACCH LAPDM T200 .............(T200F). 0 (BCF PREDEFINED VALUE)

SDCCH LAPDM T200 .............(T200S). 0 (BCF PREDEFINED VALUE)

COMMAND EXECUTED


/*** BCF IS NOT DEFINED TO MASTER CLOCK BCF ***/

You have attempted to modify a parameter which is allowed only for themaster clock BCF.

/*** CHAIN BCF NOT FOUND IN BSC DATABASE ***/

The BCF, which you have attempted to add to the chain under the masterclock BCF, does not exist.



29/02/2008



/*** ATTACHMENT OF DEFAULT BCF SOFTWARE BUILD FAILED ***/

The BCF modification was successful but attaching the software buildfailed.


The modification was successful but updating one or more BCSUs failed.After this message, a list of failed BCSU updates is output, for example, inthe following form:




DN9813196Issue 17-0 en29/02/2008




29/02/2008


EFO OUTPUT BASE CONTROL FUNCTIONPARAMETERSFunction With this command you output the BCF object parameters.

You can identify the BCF with the BCF number. You can also identifymultiple BCF numbers by using the grouping characters & and &&. Theprogram displays the data on those BCFs that are stored in the BSS RadioNetwork Configuration Database (BSDATA).

If you do not identify the BCF, the data on all BCFs in the BSDATA isdisplayed.

The command also displays the identification and the administrative stateof the BTSs controlled by the BCF and the identification of the segments(SEGs) where the BTSs are located.

Parameters BCF identification: parameter group;

Syntax EFO: [ <BCF identification> ... | <all> def ] :

[ <parameter group> | IDE def ] ;


BCF identification


You can enter multiple BCFs by using the grouping characters & and &&. Ifyou do not enter the parameter, all BCFs that exist are output.

parameter group

With this parameter you identify the BCF parameter group that is output.

DN9813196Issue 17-0 en29/02/2008


EFO OUTPUT BASE CONTROL FUNCTION PARAMETERS

IDE BCF identification parameters

HOP frequency hopping parameters

IOP external inputs and outputs of the BCF

ALL all parameters

The default value is the IDE parameter group.

Examples 1. Output the BCF identification parameters of BCFs 1 and from 3 to 8.

ZEFO:1&3&&8;

2. Output the frequency hopping parameters of BCFs number 1 and 2.

ZEFO:1&2:HOP;

3. Output all BCF parameters of BCFs 1 to 28.

ZEFO:1&&28:ALL;

4. Output the external inputs and outputs of BCF 128.

ZEFO:128:IOP;

Executionprintouts

The abbreviations used in the execution printout are:

ABIS SYNCH= BSS synchronised using Abis

AD= activation denied

BL= blocked

BL-BCF= blocked-bcf_fault

The object is blocked out of use due to a fatal BTS-site-wide failure.

BL-BTS= blocked-bts_fault

The object is blocked out of use due to a fatal sector-wide failure on the BTS site.

BL-DGN= blocked-diagnostic

The object is blocked temporarily out of use due tobase station diagnostic activities.

BL-PWR= blocked-mains_power_fault_or_manual_power_down

The object is blocked out of use due to a mains powerfailure or manual TRX power down on the BTS site.

BL-RSL= blocked-rsl_fault

The object is blocked out of use due to a telecom AbisD-channel link disconnection.


29/02/2008


BL-RST= blocked-reset

The logical radio network object is blocked out of usedue to the reset of the corresponding physical radionetwork equipment.

BL-SHD= blocked-shutting_down

The object will be blocked out of use within a timelimit. New call attempts are prohibited via an object inthe BL-SHD state and forced handovers are executedfor ongoing calls via the object.

BL-SU= blocked-bcsu_reset

The object is blocked out of use due to a BCSU unitreset on the BSC.

BL-SWO= blocked-file_based_plan_provisioning_activation

The object is blocked out of use due to File BasedPlan Provisioning activation.

BL-SYS= blocked-system

The radio network management function class of theBSC has blocked the logical object out of use due toongoing radio network recovery actions which aretriggered because of fatal faults in the BSS radionetwork.

BL-TRX= blocked-trx_fault

The object is blocked out of use due to a fatal TRX-wide failure on the BTS site.

BL-TST= blocked-testing

The object is blocked temporarily out of use due toradio network testing activities.

BL-USR= blocked-user

The operator has blocked the object out of use. Theadministrative state of the object is LOCKED or therelated higher-level object is LOCKED.

BL-WAC= blocked-waiting_for_autoconfiguration

The object is blocked out of use.

DFCA= Dynamic Frequency and Channel Allocation

EX= executing

F= false

L= locked

LMU= Location Measurement Unit

LMU SYNCH= BSS synchronised using Location Measurement Unit

DN9813196Issue 17-0 en29/02/2008



RFTE= Radio Frequency Test Equipment

SD= shutting down

SP= spare

STM= Site Test Monitor unit

SY= system

SYNCH= synchronised

T= true

U= unlocked

UA= unavailable

UNSYNCH= unsynchronised

US= user

WO= working

WO-EX= working-executing

The execution printout of the command ZEFO:125; for Nokia UltraSite isthe following:

BSC BSC-LAB 2007-10-10 13:54:32

BASE CONTROL FUNCTION BCF-0125 DATA

SITE TYPE ............................ P - ULTRASITE

ADMINISTRATIVE STATE ................. UNLOCKED

OPERATIONAL STATE .................... WO

D-CHANNEL LINK SET 1 ............. OMU12 WO-EX


TEST EQUIPMENT ...............(TEST).. STM










BTS UNDER THIS BCF ARE:

BTS-0001 SECTOR-001 CITY1 ..... LOCKED

BTS-0002 SECTOR-002 CITY2 ..... UNLOCKED


COMMAND EXECUTED

The execution printout of the command ZEFO:126; for Nokia Flexi EDGEis the following:


29/02/2008


BSC BSC-LAB 2007-10-10 13:54:32


SITE TYPE ............................ E - FLEXI EDGE



D-CHANNEL LINK SET 1 ............. OMU12 WO-EX


TEST EQUIPMENT ...............(TEST).. STM








AUTOMATIC UNLOCK ALLOWED .....(AU).... T



ABIS OVER IP ETHERNET USAGE ..(TRS1).. NOT DEFINED

ADDITIONAL 2 E1/T1 USAGE .....(TRS2).. NOT DEFINED

TRS ABIS GROOMING USAGE ......(TRS3).. NOT DEFINED

TRS LOOP PROTECTION USAGE ....(TRS4).. NOT DEFINED





COMMAND EXECUTED

The execution printout of the command ZEFO:127; for Nokia PrimeSite isthe following:

BSC BSC-LAB 2007-10-10 13:54:54






MASTER CLOCK TRX .............(MCT)... 1






COMMAND EXECUTED

The execution printout of the command ZEFO:1&&3:HOP; is thefollowing:

DN9813196Issue 17-0 en29/02/2008



BSC BSC-LAB 2007-10-10 12:54:32

FREQUENCY HOPPING PARAMETERS:

=============================

SEG-0003 CENTRE003

BCF-0001 BTS-0007 CITY7

-------------------------------------

BTS ADMINISTRATIVE STATE ... UNLOCKED

BTS OPERATIONAL STATE ...... WO

BTS HOPPING MODE..................(HOP).... BB (BASEBAND HOPPING)

BACKGROUND BTS HOPPING MODE.......(BHOP)... -

HOPPING SEQUENCE NUMBER 1......(HSN1)... 12

BACKGROUND HSN1................(BHSN1).. -



MAIO OFFSET....................(MO)..... 0 *)

BACKGROUND MAIO OFFSET.........(BMO).... -

MAIO STEP......................(MS)..... 1 *)

BACKGROUND MAIO STEP...........(BMS).... -

MOBILE ALLOCATION FREQ LIST....(MAL).... - *)

BACKGROUND MA FREQ LIST........(BMAL)... -

UNDERLAY BTS HOPPING MODE.........(UHOP)... BB (BASEBAND HOPPING)

BG UNDERLAY BTS HOPPING MODE......(BUHOP).. -

UNDERLAY HOP SEQ NUMBER........(UHSN)... 10

BG UNDERLAY HOP SEQ NUMBER.....(BUHSN).. -

UNDERLAY MAIO OFFSET...........(UMO).... 0 *)

BG UNDERLAY MAIO OFFSET........(BUMO)... -

UNDERLAY MAIO STEP.............(UMS).... 1 *)

BG UNDERLAY MAIO STEP..........(BUMS)... -

UNDERLAY MA FREQUENCY LIST.....(UMAL)... - *)

BG UNDERLAY MA FREQUENCY LIST..(BUMAL).. -

DFCA MODE ........................(DMOD)... OFF

DFCA MA FREQ LIST(S)...........(DMAL)... -

DFCA UNSYNC MODE MA FREQ LIST..(DUMAL).. - *)

MAIO VALUES PER RADIO TIMESLOT:

OVERLAY TRXS:

ADM. OP.

STATE STATE FREQ RTSL0 RTSL1 RTSL2 RTSL3 RTSL4 RTSL5 RTSL6 RTSL7

TRX-001 U WO 12 BCCH 0 0 0 0 0 0 0

TRX-002 U WO 64 0 1 1 1 1 1 1 1

TRX-003 U WO 96 1 2 2 2 2 2 2 2

TRX-004 L BL-USR 124 - - - - - - - -

UNDERLAY TRXS:

TRX-005 U WO 2 0 0 0 0 0 0 0 0

TRX-006 U WO 8 1 1 1 1 1 1 1 1

TRX-007 U WO 18 2 2 2 2 2 2 2 2

TRX-008 U WO 32 3 3 3 3 3 3 3 3


29/02/2008


SEG-0003 CENTRE03


-------------------------------------

BTS ADMINISTRATIVE STATE ... LOCKED

BTS OPERATIONAL STATE ...... BL-USR

BTS HOPPING MODE..................(HOP).... BB (BASEBAND HOPPING)






MAIO OFFSET....................(MO)..... 0 *)


MAIO STEP......................(MS)..... 1 *)




UNDERLAY BTS HOPPING MODE.........(UHOP)... N (NOT HOPPING)










DFCA MODE ........................(DMOD)... OFF

DFCA MA FREQ LIST(S)...........(DMAL)... -

DFCA UNSYNC MODE MA FREQ LIST..(DUMAL).. - *)


OVERLAY TRXS:

ADM. OP.


TRX-001 U BL-USR 31 - - - - - - - -

TRX-002 U BL-USR 32 - - - - - - - -

TRX-003 U BL-USR 33 - - - - - - - -

THERE IS NO UNDERLAY TRX UNDER BTS

SEG-0003 CENTRE03


-------------------------------------



BTS HOPPING MODE..................(HOP).... RF (RF HOPPING)


HOPPING SEQUENCE NUMBER 1 .....(HSN1)... 8


DN9813196Issue 17-0 en29/02/2008



HOPPING SEQUENCE NUMBER 2 .....(HSN2)... 0 *)


MAIO OFFSET....................(MO)..... 0


MAIO STEP......................(MS)..... 1


MOBILE ALLOCATION FREQ LIST....(MAL).... 110

FREQUENCIES:

4 6 12 96 102 108 114 120 124


UNDERLAY BTS HOPPING MODE.........(UHOP)... RF (RF HOPPING)




UNDERLAY MAIO OFFSET...........(UMO).... 0


UNDERLAY MAIO STEP.............(UMS).... 1


UNDERLAY MA FREQUENCY LIST.....(UMAL)... -


DFCA MODE ........................(DMOD)... STANDBY

DFCA MA FREQ LIST(S)...........(DMAL)... 2001 2005 2007

DFCA UNSYNC MODE MA FREQ LIST..(DUMAL).. 209 *)


OVERLAY TRXS:

ADM. OP.


TRX-005 U WO 24 BCCH - - - - - - -

TRX-006 U WO 35 0 0 0 0 0 0 0 0

TRX-007 U WO 54 1 1 1 1 1 1 1 1

TRX-008 U WO 59 2 2 2 2 2 2 2 2


SEG-0004 CENTRE04


-------------------------------------









MAIO OFFSET....................(MO)..... 3


MAIO STEP......................(MS)..... 1




29/02/2008


FREQUENCIES:

4 6 12 96 102 108 114 120 124

BACKGROUND MA FREQ LIST.......(BMAL)... -











DFCA MODE ........................(DMOD)... DFCA


DFCA UNSYNC MODE MA FREQ LIST..(DUMAL).. 120

FREQUENCIES:

8 14 24 68 88 104 110 116 122


OVERLAY TRXS:

ADM. OP.


TRX-009 U WO 64 BCCH - - - - - - -

TRX-010 U WO 87 3 3 3 3 3 3 3 3

TRX-011 U WO 45 4 4 4 4 4 4 4 4

TRX-012 U WO 121 5 5 5 5 5 5 5 5


DFCA TRXS:

TRX-013 U WO 75 1 1 1 1 1 1 1 1

TRX-014 U WO 79 3 3 3 3 3 3 3 3

TRX-015 U WO 83 5 5 5 5 5 5 5 5

SEG-0004 CENTRE04


-------------------------------------









MAIO OFFSET....................(MO)..... 6


MAIO STEP......................(MS)..... 1



DN9813196Issue 17-0 en29/02/2008



FREQUENCIES:

4 6 12 96 102 108 114 120 124


UNDERLAY BTS HOPPING MODE.........(UHOP)... RF (RF HOPPING)




UNDERLAY MAIO OFFSET...........(UMO).... 9


UNDERLAY MAIO STEP.............(UMS).... 1


UNDERLAY MA FREQUENCY LIST.....(UMAL)... 112

FREQUENCIES:

1 3 21 23 45 49 77 81 85 89

113 117 119 121






OVERLAY TRXS:

ADM. OP.


TRX-013 U WO 96 BCCH - - - - - - -

TRX-014 U WO 6 6 6 6 6 6 6 6

TRX-015 U WO 7 7 7 7 7 7 7 7

TRX-016 U WO 8 8 8 8 8 8 8 8

UNDERLAY TRXS:

TRX-001 U WO 9 9 9 9 9 9 9 9

TRX-002 U WO 10 10 10 10 10 10 10 10

TRX-003 U WO 11 11 11 11 11 11 11 11

TRX-004 U WO 12 12 12 12 12 12 12 12

THERE IS NO DFCA TRX UNDER BTS

SEG-0004 CENTRE04


-------------------------------------



BTS HOPPING MODE..................(HOP).... N (NOT HOPPING)






MAIO OFFSET....................(MO)..... 0 *)



29/02/2008


MAIO STEP......................(MS)..... 1 *)






UNDERLAY HOP SEQ NUMBER........(UHSN)... - *)


UNDERLAY MAIO OFFSET...........(UMO).... - *)










OVERLAY TRXS:

ADM. OP.


TRX-001 U WO 100 BCCH

TRX-002 U WO 104

TRX-003 L BL-USR 110

TRX-004 U WO 116


DFCA TRXS:

TRX-008 U WO 35 - - - - - - - -

TRX-009 U WO 43 - - - - - - - -

TRX-010 U WO 54 - - - - - - - -

*) NOT RELEVANT IN THIS HOPPING MODE

COMMAND EXECUTED

The execution printout of the command ZEFO:120:IOP; for NokiaMetroSite is the following:

BSC BSC-LAB 2007-10-10 12:54:32

EXTERNAL INPUT AND OUTPUT DATA:

===============================

BCF-0120: EXTERNAL OUTPUTS

-------------------------

OUTPUT 1 ....................... ON TEXT ID 2




DN9813196Issue 17-0 en29/02/2008

























COMMAND EXECUTED

The execution printout of the command ZEFO:128:IOP; for Nokia 2ndgeneration is the following:

BSC BSC-LAB 2007-10-10 12:55:32

EXTERNAL INPUT AND OUTPUT DATA:

===============================

BCF-0128: EXTERNAL OUTPUTS

-------------------------

OUTPUT 1 .......................... ON

OUTPUT 2 .......................... ON

OUTPUT 3 .......................... OFF

OUTPUT 4 .......................... OFF

OUTPUT 5 .......................... OFF

OUTPUT 6 .......................... OFF

COMMAND EXECUTED

The execution printout of the command ZEFO:6:IDE; for Nokia Talk-family is the following:

BSC BSC-LAB 2007-10-10 09:51:27


SITE TYPE ............................ D - TALK-FAMILY



29/02/2008



D-CHANNEL LINK SET 5 ............. DONNA WO-EX






MASTER CLOCK BCF .............(MCBCF). --

CLOCK SOURCE .................(CS).... --






BTS-006 DONNA ............... UNLOCKED

COMMAND EXECUTED

The execution printout of the command ZEFO:50:; for Nokia Flexi EDGEis the following:

BSC KANTOB95 2007-10-09 14:15:49


SITE TYPE .......................... E – FLEXI EDGE

ADMINISTRATIVE STATE ............... UNLOCKED

OPERATIONAL STATE .................. WO

D-CHANNEL LINK SET 380 ............ OM190 WO-EX

RX DIFFERENCE LIMIT ...........(RXDL).. 10 dB

BTS BATTERY BACKUP PROCEDURE ..(BBU)... ALL

TRX SHUTDOWN TIMER ............(NTIM).. 0 min

TRX SHUTDOWN TIMER2 ...........(NTIM2). 0 min

TRX SHUTDOWN TIMER3 ...........(NTIM3). 0 min

BCCH TRX SHUTDOWN TIMER .......(BTIM).. 0 min

MASTER CLOCK BCF ..............(MCBCF). –-

CLOCK SOURCE ..................(CS).... –-

SYNCHRONIZATION ENABLED .......(SENA).. F

SYNCHRONIZATION MODE ..........(SM).... UNSYNCH

AUTOMATIC UNLOCK ALlOWED ......(AU).... T

FACCH LAPDM T200 ..............(T200F). 0 (BCF PREDEFINED VALUES)

SDCCH LAPDM T200 ..............(T200S). 0 (BCF PREDEFINED VALUES)

ABIS OVER IP ETHERNET USAGE ...(TRS1).. 1 (IN USE)

ADDITIONAL 2 E1/T1 USAGE ......(TRS2).. 2 (IN USE)

TRS ABIS GROOMING USAGE .......(TRS3).. 0 (NOT IN USE)

TRS LOOP PROTECTION USAGE .....(TRS4).. 0 (NOT IN USE)





COMMAND EXECUTED

DN9813196Issue 17-0 en29/02/2008






In error conditions, the general execution error messages of the MMLcommands are output. For more information, see General Error Messagesof System.


29/02/2008


EFL OUTPUT BASE CONTROL FUNCTIONSYNCHRONIZATION CONFIGURATIONFunction With this command you output the BCF objects synchronisation

configuration.

You can identify the BCF with the BCF number. You can also identifymultiple BCF numbers with the grouping characters & and &&. Theprogram displays the synchronisation data on those BCFs that are storedin the BSS Radio Network Configuration Database (BSDATA).

If you do not identify the BCF, the synchronisation data on all BCFs in theBSDATA is displayed.

The command is not available for the Nokia 2nd generation, NokiaPrimeSite, or Nokia InSite site types.

Parameters BCF identification: synch enabled: BSC-BSC interface failure <option>;

Syntax

EFL: [ <BCF identification> ... | <all> def ] :

[ <synch enabled> | <all> def ] :

[ BSCBSC = <BSC-BSC interface failure> <option> | <all> def ] ;


BCF identification

With this parameter you identify the BCF with a decimal number. The valuerange depends on the BSC hardware configuration and the correspondingoptions. You can enter multiple BCFs with the grouping characters & and&&.

If you do not enter the parameter, the synchronisation data of all chainsand independent mode BCFs depending on the given parameter valuesfor synch enabled and BSC-BSC interface failure are output.

DN9813196Issue 17-0 en29/02/2008


EFL OUTPUT BASE CONTROL FUNCTION SYNCHRONIZATIONCONFIGURATION

If you give this parameter, you cannot give the BSC-BSC interfacefailure parameter.

synch enabled

With this parameter you output the synchronisation data of chains orindependent mode BCFs which have the defined synchronisation status.

The values are:




If you do not enter the parameter, the synchronisation data of all BCFsdepending on the given parameter values for BCF identification andBSC-BSC interface failure are output.

If you give this parameter, you cannot give the BSC-BSC interfacefailure parameter.

BSC-BSC interface failure <option>

With this parameter you output the synchronisation data and DFCA TRXsof the DFCA BTSs which have the defined BSC-BSC interface status. Thedata of a BTS is output if the DFCA mode of the BTS is STANDBY orDFCA hopping, and the BTS has the BSC-BSC interface status defined bythis parameter.

OK Output DFCA BTSs which do not suffer from a BSC-BSC interface failure.

NOK Output DFCA BTSs which suffer from a BSC-BSCinterface failure.

If you give this parameter, you cannot give the BCF identification orsynch enabled parameters.

Examples 1. Output the synchronisation data of all BCFs.

ZEFL;

2. Output the synchronisation data of BCFs 1 to 10 which havesynchronisation enabled.

ZEFL:1&&10:T;


29/02/2008


3. Output the synchronisation data and DFCA TRXs of DFCA BTSswhich suffer from a BSC-BSC interface failure.

ZEFL:::BSCBSC=NOK;

4. Output the synchronisation data of all BCFs whose BCF chainsynchronisation is enabled.

ZEFL::T:;


In the execution printout, if the BSC-BSC interface status is 'NOK', itmeans that the BSC has noticed an inter-BSC connection failure leading toexcessive uncontrolled interference in the DFCA TRXs of the BTS due tothe lack of up-to-date knowledge on some of the remote interfering cells.As a result, the BTS is operating in an unsynchronised random frequencyhopping DFCA mode.

Executionprintouts

The abbreviations used in the execution printout are:

ABIS SYNCH= BSS synchronised using Abis

BL= blocked

BL-BCF= blocked-bcf_fault

The object is blocked out of use due to a fatal BTS-site-wide failure.

BL-BTS= blocked-bts_fault

The object is blocked out of use due to a fatal sector-wide failure on the BTS site.

BL-DGN= blocked-diagnostic

The object is blocked temporarily out of use due tobase station diagnostic activities.

BL-PWR= blocked-mains_power_fault_or_manual_power_down

The object is blocked out of use due to a mains powerfailure or manual TRX power down on the BTS site.

BL-RSL= blocked-rsl_fault

The object is blocked out of use due to a telecom AbisD-channel link disconnection.

BL-RST= blocked-reset

The logical radio network object is blocked out of usedue to the reset of the corresponding physical radionetwork equipment.

BL-SHD= blocked-shutting_down

DN9813196Issue 17-0 en29/02/2008



The object will be blocked out of use within a timelimit. New call attempts are prohibited via an object inthe BL-SHD state and forced handovers are executedfor ongoing calls via the object.

BL-SU= blocked-bcsu_reset

The object is blocked out of use due to a BCSU unitreset on the BSC.

BL-SWO= blocked-file_based_plan_provisioning_activation

The object is blocked out of use due to File BasedPlan Provisioning activation.

BL-SYS= blocked-system

The radio network management function class of theBSC has blocked the logical object out of use due toongoing radio network recovery actions which aretriggered because of fatal faults in the BSS radionetwork.

BL-TRX= blocked-trx_fault

The object is blocked out of use due to a fatal TRX-wide failure on the BTS site.

BL-TST= blocked-testing

The object is blocked temporarily out of use due toradio network testing activities.

BL-USR= blocked-user

The operator has blocked the object out of use. Theadministrative state of the object is LOCKED or therelated higher-level object is LOCKED.

BL-WAC= blocked-waiting_for_autoconfiguration

The object is blocked out of use.

BSC–BSC = BSC-BSC interface status

DFCA MODE= Dynamic Frequency and Channel Allocation Mode

DFCA = DFCA Hopping

DFCA TRX= DFCA TRX status

F= false

L= locked

LMU= Location Measurement Unit

LMU-ABIS= Location Measurement Unit with Abis recovery

LMU SYNCH= BSS synchronised using Location Measurement Unit

SYNCH= synchronised

T= true


29/02/2008


U= unlocked

UNSYNCH= unsynchronised

WO= working

WO-EX= working-executing

The execution printout of the command example 1 is the following:

BSC BSC-LAB 2007-10-10 12:28:13

SYNCHRONIZATION CONFIGURATION IN BSC:

CLOCK SYNCH SYNCH ADM OP DFCA BSC-

SOURCE ENABLED MODE STA STATE MODE BSC

================= ======== ======= ========== === ====== ======= ====

MASTER BCF-0001 LMU T SYNCH U WO

BTS-0001 U WO

BTS-0002 U WO

BCF-0002 SYNCH U WO

BTS-0003 U WO

BTS-0004 U WO

BCF-0003 UNSYNCH L BL-USR

BTS-0005 L BL-USR

BTS-0006 L BL-USR

MASTER BCF-0004 BCF F UNSYNCH U WO

BTS-0007 U WO

BTS-0008 U WO

BCF-0005 UNSYNCH L BL-USR

BTS-0009 L BL-USR

BTS-0010 L BL-USR

BCF-0006 UNSYNCH U WO

BTS-0011 U WO

BTS-0012 U WO

ALONE BCF-0008 PCM T SYNCH U WO

BTS-0013 U WO

BTS-0014 U WO

COMMAND EXECUTED

When the DFCA licence is activated, the execution printout of thecommand example 2 is the following:

BSC BSC-LAB 2007-10-10 10:35:55




================= ======== ======= ========== === ====== ======= ====


BTS-0001 U WO DFCA OK

BTS-0002 U WO OFF -

DN9813196Issue 17-0 en29/02/2008



BCF-0002 SYNCH U WO

BTS-0003 U WO STANDBY NOK


BCF-0003 SYNCH U WO


BTS-0006 U WO DFCA NOK

ALONE BCF-0008 PCM T SYNCH U WO

BTS-0013 U WO OFF -

BTS-0014 U WO OFF -

COMMAND EXECUTED

The printout of the command example 3 is the following:

BSC BSC-LAB 2007-10-10 11:36:32




================= ======== ======= ========== === ====== ======= ====


BCF-0002 SYNCH U WO

BTS-0003 U WO STANDBY NOK

DFCA TRX-002 U WO

DFCA TRX-003 U WO

DFCA TRX-005 U WO

BCF-0003 SYNCH U WO

BTS-0006 U WO DFCA NOK

DFCA TRX-001 U WO

DFCA TRX-004 U WO

COMMAND EXECUTED

The printout of the command example 4 is the following:

BSC BELLE 2007-10-10 14:29:02




================= ======== ======= ========== === ====== ======= ====

MASTER BCF-0209 LMU-ABIS T LMU SYNCH U WO

BTS-0209 U WO OFF -

BTS-0512 U WO OFF -

BCF-0201 LMU SYNCH U WO

BTS-0201 U WO OFF -

BTS-0202 U WO OFF -


MASTER BCF-0210 LMU-ABIS T ABIS SYNCH U WO

BTS-0210 U WO OFF -

BTS-0211 U WO OFF -


29/02/2008


BCF-0205 ABIS SYNCH U WO

BTS-0205 U WO OFF -

BTS-0206 U WO OFF -


COMMAND EXECUTED


If an error occurs, the general semantic error messages of the MMLcommands are output. For more information, see General NoticeMessages of MML Session.


In error conditions, the general execution error messages of the MMLcommands are output. For more information, see General Error Messagesof System.

DN9813196Issue 17-0 en29/02/2008




29/02/2008


EFS CHANGE BASE CONTROL FUNCTIONADMINISTRATIVE STATEFunction With this command you change the BCF's administrative state.

Parameters BCF identification: administrative state;

Syntax EFS: <BCF identification> :

<administrative state> ;


BCF identification


administrative state

With this parameter you lock or unlock the object.

U: Unlock the object.

L: Lock the object.


Examples 1. Lock the BCF 128.

ZEFS:128:L;

Executionprintouts


DN9813196Issue 17-0 en29/02/2008


EFS CHANGE BASE CONTROL FUNCTION ADMINISTRATIVESTATE

BSC BSC-LAB 2007-10-10 13:54:32

BASE CONTROL FUNCTION BCF-0128 STATE LOCKED

COMMAND EXECUTED





The state change was successful but updating one or more BCSUs failed.After this message, a list of failed BCSU updates is output, for example, inthe following form:





29/02/2008


EFT SET BASE CONTROL FUNCTION OUTPUTSFunction With this command you modify the states of the external outputs of the

BCF object in the BSS Radio Network Configuration Database (BSDATA).

The command is not available for the Nokia PrimeSite or Nokia InSite sitetypes.

In the case of Nokia MetroSite, the number of the outputs is 4.

Parameters BCF identification: external outputs ON, external outputs OFF;

Syntax EFT: <BCF identification> :

( ON = <external outputs ON> ... |

OFF = <external outputs OFF> ... ) ... ;


BCF identification


external outputs ON

ON = decimal number

With this parameter you define the external outputs that are set into the ONstate. You can set multiple outputs in the same command with thegrouping characters & and &&.

You must enter at least one of the parameters ON or OFF.

The default value is all outputs OFF.

external outputs OFF

DN9813196Issue 17-0 en29/02/2008


EFT SET BASE CONTROL FUNCTION OUTPUTS

OFF = decimal number

With this parameter you define the external outputs that are set into theOFF state. You can set multiple outputs in the same command with thegrouping characters & and &&.

You must enter at least one of the parameters ON or OFF.

The default value is all outputs OFF.

Examples 1. Set the external outputs 1, 2, and 3 of BCF-128 to ON, and set theexternal outputs 4, 5, and 6 to OFF.

ZEFT:128:ON=1&&3,OFF=4&&6;

2. In the case of Nokia MetroSite, set the external outputs 1 and 2 ofBCF-120 to ON, and set the external outputs 3 and 4 to OFF.

ZEFT:120:ON=1&2,OFF=3&4;

Executionprintouts


BSC BSC-LAB 2007-10-10 13:54:32

BASE CONTROL FUNCTION BCF-0128 OUTPUT IS MODIFIED

OUTPUT 1 .................... ON

OUTPUT 2 .................... ON

OUTPUT 3 .................... ON

OUTPUT 4 .................... OFF

OUTPUT 5 .................... OFF

OUTPUT 6 .................... OFF

COMMAND EXECUTED


BSC BSC-LAB 2007-10-10 13:54:32

BASE CONTROL FUNCTION BCF-0120 OUTPUT IS MODIFIED

OUTPUT 1 .................... ON TEXT ID 2


OUTPUT 2 .................... ON TEXT ID 5

MAST WARNING LIGHTS

OUTPUT 3 .................... OFF TEXT ID -

OUTPUT 4 .................... OFF TEXT ID -

COMMAND EXECUTED


29/02/2008



/*** ERROR IN ON/OFF PARAMETER VALUES ***/

You have attempted to give the same external output number to both theON and the OFF parameter.




The output state change was successful but updating one or more BCSUsfailed. After this message, a list of failed BCSU updates is output, forexample, in the following form:




DN9813196Issue 17-0 en29/02/2008


EFT SET BASE CONTROL FUNCTION OUTPUTS


29/02/2008


EFX SET BASE CONTROL FUNCTIONEXTERNAL INPUT PARAMETERSFunction With this command you set BCF object's external input parameters in the

BSS Radio Network Configuration Database (BSDATA).

The command is allowed only if the site type is Nokia MetroSite, NokiaUltraSite, or Nokia Flexi EDGE.

Parameters BCF identification: external input number: route, polarity: severity, text ID;

Syntax EFX: <BCF identification> :

INBR = <external input number> :

[ ROU = <route> |

POL = <polarity> ] ... :

[ SEV = <severity> |

TID = <text ID> ] ... ;


BCF identification



external input number

INBR = decimal number

With this parameter you define the external input number. The valuesrange from 1 to 10 for Nokia MetroSite, and from 1 to 24 for Nokia UltraSiteand Nokia Flexi EDGE.

DN9813196Issue 17-0 en29/02/2008


EFX SET BASE CONTROL FUNCTION EXTERNAL INPUTPARAMETERS


route

With this parameter you activate the routing of the input alarm and choosewhere the alarm is sent.

This parameter defines the reporting route of external alarms of a BCF.The BCF sends alarm indications to the BSC and the NMS/2000 (ACT) orto the NMS/100 (TMS) according to the value of this parameter.

The values are:


ROU = NOT Not activated (notreported).

ACT Activated, reported to theBSC as a normal externalalarm.

TMS Activated, reported as atransmission alarm to theTransmission ManagementSystem.

MAINS Activated, reported to theBSC as a MainsBreakdown alarm.

The transmission management system can be BSC, BTS, or externalmanagement system (for example NMS/10 MF).

This parameter is visible only for Nokia MetroSite, Nokia UltraSite, andNokia Flexi EDGE BTS site types.

polarity

With this parameter you define the actual polarity of the external inputconnection. In the case of state transition in the input connection, the BCFreports either the alarm or the cancel message according to the value ofthis parameter.

The values are:


POL = OPEN Active when open.


29/02/2008



CLOSED Active when closed.


severity

With this parameter you define the severity of the input alarm.

The values are:


SEV = AL3 The highest alarm level.

AL2 The medium alarm level.

AL1 The lowest alarm level.

If the value of the route parameter is TMS (NMS/100), parametersseverity and text ID are not relevant.


text ID

TID = decimal number

With this parameter you refer to the text string. The values range from 1 to200.

To remove the input's text ID, enter the value 0 (0 = text not defined).

If the value of the route parameter is TMS (NMS/100), parametersseverity and text ID are not relevant.

Examples 1. Set the external input number of BCF-128 to value 1 and set theparameters as follows:

route to the NMS/2000 (ACT), polarity to OPEN, and the severityclass to value AL3 with text ID 100.

ZEFX:128:INBR=1:ROU=ACT,POL=OPEN:SEV=AL3,TID=100;

DN9813196Issue 17-0 en29/02/2008


EFX SET BASE CONTROL FUNCTION EXTERNAL INPUTPARAMETERS

2. Set the external input number of BCF-1 to value 10 and set theparameters as follows:

route to the NMS/100 (TMS) and polarity to OPEN.

ZEFX:1:INBR=10:ROU=TMS,POL=OPEN;

Executionprintouts

The execution printout of command example 1 is the following

BSC BSC-LAB 2007-10-10 12:54:32

EXTERNAL INPUT OF BCF-0128 MODIFIED




COMMAND EXECUTED






29/02/2008


EFR RESET BASE CONTROL FUNCTIONFunction With this command you reset the BTS site or the OMU of the BTS site.

Parameters BCF identification: reset type;

Syntax EFR: <BCF identification> :

[ <reset type> | SITE def ] ;


BCF identification


reset type

With this parameter you define the type of the reset.

SITE The whole BTS site is reset.

OMU The OMU of the BTS site is reset.

The default value is SITE.

The reset fails if the BCF is waiting for autoconfiguration.

OMU reset is only allowed for the Nokia 2nd generation, Nokia Talk-family,Nokia UltraSite, and Nokia Flexi EDGE site types.

DN9813196Issue 17-0 en29/02/2008


EFR RESET BASE CONTROL FUNCTION

Note

Operation and maintenance unit (OMU) reset fails if the base controlfunction (BCF) is in ABIS SYNCH mode or being changed into ABISSYNCH mode. The resulting error message is: INVALID OBJECTSTATE.

Examples 1. Reset the BTS site in BCF-128.

ZEFR:128;

2. Reset the OMU of the BTS site in BCF-66.

ZEFR:66:OMU;


Before executing the command, the system asks for confirmation:

THIS COMMAND CUTS ALL ONGOING CALLS IN THE RESETED BTS SITE

CONFIRM COMMAND EXECUTION: Y/N ?

Executionprintouts


BSC BSC-LAB 2007-10-10 13:54:32

BCF-0128: BTS SITE RESET STARTED

COMMAND EXECUTED


BSC BSC-LAB 2007-10-10 15:07:32

BCF-0066: OPERATION AND MAINTENANCE UNIT RESET OF THE BTS SITE STARTED

COMMAND EXECUTED




In error conditions, the general execution error messages of the MMLcommands are used. For more information, see General Error Messagesof System.


29/02/2008


EFE MODIFY EXTERNAL INPUT AND OUTPUTTEXTFunction With this command you can create a text string in the BSS Radio Network

Configuration Database (BSDATA), modify it, and delete it from it.

Parameters text ID: text string;

Syntax EFE: TID = <text ID> :

TEXT = <text string>;


text ID


With this parameter you define the text ID number of a text string. Thevalues range from 1 to 200.


text string

TEXT = text string

With this parameter you define the text string. The length of the text stringmust not be more than 80 characters. The text string must be enteredinside quotation marks. The text string can include following characters:

Capital letters: A...Z

Numbers: 0...9

Characters: < > _ - / ( ) , . ! # $ @ % & * + ' = and space

DN9813196Issue 17-0 en29/02/2008


EFE MODIFY EXTERNAL INPUT AND OUTPUT TEXT

You can delete a text string by leaving the text field empty inside thequotation marks. In this case the MML asks you to confirm the operation.The delete operation removes the text string connection from the BCF(s).


Examples 1. Create the text ID 100.

ZEFE:TID=100:TEXT="SMOKE ALARM";

2. Delete the text ID 100.

ZEFE:TID=100:TEXT="";


Before the deletion is executed, the system asks for confirmation:

YOU ARE DELETING TEXT STRING AND REMOVING TEXT STRING CONNECTION

CONFIRM COMMAND EXECUTION: Y/N ?

Executionprintouts


BSC BSC-LAB 2007-10-10 13:54:32

TEXT ID 100 CREATED

SMOKE ALARM

COMMAND EXECUTED






29/02/2008


EFP OUTPUT EXTERNAL INPUT AND OUTPUTTEXTSFunction With this command you output the use of the texts. The command outputs

the texts and lists the BCFs using the text.

Parameters text ID, printout format;

Syntax EFP: [ TID = <text ID> ... | <all> def |

FORM = <printout format> | SHORT def ] ... ;


text ID


With this parameter you define the text ID number of a text string. Thevalues range from 1 to 200.

You can enter multiple text IDs with the grouping characters & and &&. Ifyou do not enter any decimal number to this parameter, all defined textsfrom the BSS Radio Network Configuration Database (BSDATA) will beoutput.

The default value is 'all'.

printout format

With this parameter you choose the type of the printout.

You choose between the long format and the short format. The differencebetween the long and short format is that the long format includes theBCFs using the text.

The values are:

DN9813196Issue 17-0 en29/02/2008


EFP OUTPUT EXTERNAL INPUT AND OUTPUT TEXTS


FORM = LONG Outputs the defined textincluding the BCFs usingthe text.

SHORT Outputs only the definedtext.

The default value is SHORT.

Examples 1. Output the text ID number 1 in the long format.

ZEFP:TID=1,FORM=LONG;

2. Output all the texts in the short format.

ZEFP;

Executionprintouts


BSC BSC-LAB 2007-10-10 12:54:32

INPUT AND OUTPUT TEXT(S)

TEXT ID 1

SMOKE ALARM

BCF(S) USING THE TEXT:

0001 0005 0006 0128

COMMAND EXECUTED


BSC BSC-LAB 2007-10-10 12:54:32

INPUT AND OUTPUT TEXT(S)

TEXT ID 1

SMOKE ALARM

TEXT ID 2


TEXT ID 99


COMMAND EXECUTED


29/02/2008






DN9813196Issue 17-0 en29/02/2008


EFP OUTPUT EXTERNAL INPUT AND OUTPUT TEXTS

NSN Zef

Documents

Transcript of NSN Zef