MTM Decorative Gas Fires - The Fire Basket Ltd · MTM Decorative Gas Fires With upgradable control...
-
Upload
nguyennhan -
Category
Documents
-
view
228 -
download
0
Transcript of MTM Decorative Gas Fires - The Fire Basket Ltd · MTM Decorative Gas Fires With upgradable control...
MTM Decorative Gas FiresWith upgradable control valve
Instructions for Use,Installation and ServicingFor use in GB, IE (Great Britain and Eire)
PR0704 Issue 5 (June 2011)
IMPORTANTDo not attempt to burn rubbish in this appliance. This appliance will become hot whilst in operation, it is therefore
recommended that a suitable guard should be used for the protection of young children, the elderly or infirm.
Please read these Instructions carefully before installation or use. Keep them in a safe place for future reference and when servicing the fire.
The commissioning sheet on page 3 MUST be completed by the Installer.
This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the translated instructions and in some cases the appliance will require modification. Contact Gazco for further information.
2
CONTENTS PAGE
APPlIANCE COMMISSIONING ChECKlIST 3
USER INSTRUCTIONS 4
INSTAllATION INSTRUCTIONS 12 Technical Specifications 12
Site Requirements 14
Installation 16
Fires Fitted with Seagas & Babysit Valve 17
Fires Fitted with Mertik Maxitrol Valve 25
Commissioning 31
SERvICING INSTRUCTIONS 32 Servicing Requirements 32
Fault Finding 33
How to replace parts 35
Basic spare parts list 40
Models 41
Service Records 43
Covering the following modelsSP & PSP MTM Fires.
Gas Fires used in Stovax Classic Fireplaces.Gas Fires in the Gazco Basket Fires Range.
INTRODUCTION - IMPORTANTThe Gazco MTM range, is designed to cover a variety of fire shapes and sizes, from Victorian cast iron to a large centrepiece in a pub or restaurant. Gazco also use the MTM based fire for the Stovax cast iron fireplaces and a range of basket fires.
The range now includes Pebbles and Driftwood and an upgradeable control valve for some of the range.
For pebble fires follow the layout for coals. For driftwood follow the log layouts.Follow the appropriate section for the control type and position in the installation instructions.
3
FlUE ChECK PASS FAIl
1. Flue is correct for appliance
2. Flue flow test
3. Spillage test
GAS ChECK
1. Gas soundness & let by test
2. Standing pressure test mb
3. Appliance working pressure (on High Setting) mb
NB All other gas appliances must be operating on full
MTM FIRES ONly SeTTING PReSSuRe (Not Mertik Maxitrol upgradeable Valve) High Low
mb mb
4. Gas rate m3/h
5. Does ventilation meet appliance requirements
6. Have controls been upgraded (upgradeable models only) 8455 Standard YeS NO
APPlIANCE COMMISSIONING ChECKlIST
Dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date of Purchase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engineer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Safe Reg No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date of Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT NOTICEExplain the operation of the appliance to the end user, hand the completed instructions to them for safe keeping,
as the information will be required when making any guaranteed claims.
DEAlER AND INSTAllER INFORMATION
This product is guaranteed for 2 years from the date of installation, as set out in the terms and conditions of sale between Gazco and your local Gazco dealer. This guarantee will be invalid, to the extent permitted by law, if the above Appliance Commissioning Checklist is not fully completed by the installer and available for inspection by a Gazco engineer. The guarantee will only be valid during the second year, to the extent permitted by law, if the annual service recommended in the Instructions for use has been completed by a Gas Safe registered engineer, and a copy of the service visit report is available for inspection by a Gazco engineer.
4
USER INSTRUCTIONS
1. GENERAl
In the event of a gas escape or if you can smell gas, please take the following steps:
• Immediatelyturnoffthegassupplyatthemeter/ emergency control valve
• Extinguishallsourcesofignition • Donotsmoke • Donotoperateanyelectricallightorpowerswitches (On or Off) • Ventilatethebuilding(s)byopeningdoorsand
windows • Ensureaccesstothepremisescanbemade
Please report the incident immediately to the National Gas Emergency Service Call Centre on 0800 111 999 (England, Scotland and Wales) , 0800 002 001 (N. Ireland) or in the case of lPG, the gas supplier whose details can be found on the bulk storage vessel or cylinder.
The gas supply must not be used until remedial action has been taken to correct the defect and the installation has been recommissioned by a competent person.
1.1 Installation and servicing must only be carried out by a competent person whose name appears on the Gas Safe register. To ensure the engineer is registered with Gas Safe they should possess an ID Card carrying the following logo:
1.2 In all correspondence, please quote the appliance type and serial number, which can be found on the databadge located on a chain beneath the control valve.
1.3 ensure that curtains are not positioned above the fire, and that there is a 300mm minimum clearance between the sides of the fire and any curtains.
1.4 This product is guaranteed for 2 years from the date of installation, as set out in the terms and conditions of sale between Gazco and your local Gazco dealer. Please consult with your local Gazco dealer if you have any questions. In all correspondence always quote the Model Number and Serial Number.
2. lIGhTING ThE APPlIANCE
2.1 According to specification, there are 3 different types of control which can be supplied with your fire. It is important to identify which control you have before lighting the appliance.
2.2 Control Type A
1
Seagas Valve
a) ensure the control is pointing to the off position ( ), see diagram 1.
b) Firmly push the control knob in and rotate anti-clockwise until a click is heard and the knob is pointing at the ignition symbol ( ), the pilot should now be lit.
c) Continue to push the knob in for 5 to 10 seconds and then release, the pilot should remain alight. If the pilot does not light, repeat the above procedure.
d) If it will not light after repeated attempts, the appliance may be lit by match as a temporary measure, see section 4.
e) The appliance may now be turned to the high ( ) position to ignite the main burner, then controlled between high
( ) and low ( ) as desired.
ThE FlAMES WIll TURN yEllOW WhEN ThE FIRE hAS GAINED SUFFICIENT hEAT - TyPICAlly 10 TO 20 MINUTES.
2.3 Control Type B
2
Babysit Valve
a) ensure the control is pointing to the off position ( ), see diagram 2.
5
b) Rotate anti-clockwise until the pointer on the fascia points to the ignition ( ) symbol on the knob.
c) Firmly push the knob in and whilst holding the knob in, push the igniter button 2 or 3 times. The pilot should now be lit.
d) Continue to push the knob in for 5 to 10 seconds and then release, the pilot should remain alight. If the pilot does not light, repeat the above procedure.
e) If it will not light after repeated attempts, the appliance may be lit by a match as a temporary measure, see Section 4.
f) The appliance may now be turned to the high position to ignite the main burner, then controlled between high ( ) and low ( ) as desired.
ThE FlAMES WIll TURN yEllOW WhEN ThE FIRE hAS GAINED SUFFICIENT hEAT TyPICAlly 10 TO 20 MINUTES.
2.4 Control Type C
3
AR0914
a) Locate the control valve on the appliance. There are two control knobs on the valve, the right-hand knob controls the pilot ignition and the left-hand knob controls the main burner.
b) If your appliance has already been upgraded to battery remote control, please refer to the instructions provided with the upgrade to operate the remote control. The following instructions will work for either situation.
c) ensure that the left-hand control knob is pointing to off ( ).
d) ensure that the right-hand control knob is pointing to off ( ).
e) Press in the right-hand control knob and rotate it anti-clockwise until a click is heard (keep pressing in) and the knob is pointing to pilot ( ). The pilot should now light. If the pilot has not lit, repeat the procedure until it does.
f) Keep the control knob pressed for 10 seconds and then release it, the pilot should stay alight. If the pilot goes out, repeat the procedures until it does.
g) If the pilot will not light after repeated attempts, contact the retailer or installer from whom the appliance was purchased.
h) Turn the right-hand control to point to main burner ( ). The appliance can now be controlled using the left-hand control knob.
i) Turn the left-hand control knob to point to low fire ( ), the main burner will light on low. The burner can now be controlled between low and high settings. Turn the control knob anti-clockwise to increase the flame height and clockwise to decrease the flame height.
ThE yEllOW FlAMES WIll APPEAR WhEN ThE FIRE hAS GAINED SUFFICIENT hEAT - TyPICAlly 10 TO 20 MINUTES.
3. TURNING ThE APPlIANCE OFF
3.1 Control Type A
a) Depress the control knob and turn clockwise until the knob is pointing at the off position ( ).
3.2 Control Type B
a) Depress the control knob and turn clockwise until the knob is pointing at the off position ( ).
3.3 Control Type C
a) To turn the fire off, locate the control valve, turn the left-hand control knob until it points to off ( ). The main burner will go out leaving the pilot burning.
b) To turn the pilot off, locate the control valve, turn the right-hand control knob until it points to off ( ), the pilot will go out.
3.4 IF ThE FIRE IS ExTINGUIShED OR GOES OUT IN USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO RE-lIGhT.
3.5 After the fire has been turned off, the gas left in the burner will continue to burn, causing a crackling or popping noise. This is quite normal and will last up to one minute.
4. lIGhTING ThE FIRE WITh A MATCh4.1 If the pilot does not ignite as described in Section 2, it may
be lit with a match. Identify which valve you have (see section 2).
4
AR0954
USER INSTRUCTIONS
6
4.2 Control Type A
a) Firmly push the control knob in and rotate anti-clockwise until the knob is pointing at the ignition symbol ( ), whilst holding the knob in, apply a lighted match to the pilot hood, the pilot should light, see diagram 1.
b) Continue to push the knob in for 5 to 10 seconds and then release. The pilot should remain alight.
c) The fire may now be controlled as previously described.
4.3 Control Type B
a) Rotate anti-clockwise until the pointer on the fascia points to the ignition ( ) symbol on the knob.
b) Firmly push the knob in and whilst holding the knob in, apply a lighted match to the pilot head, the pilot should light, see diagram 1.
c) Continue to hold in the knob for 5 to 10 seconds and then release. The pilot should remain alight.
d) The fire may now be controlled as previously described.
4.4 Control Type C
a) Press in the right-hand control knob and rotate it anti-clockwise until a click is heard (keep pressing in) and the knob is pointing to pilot ( ), apply a lighted match to the pilot hood, see diagram 1.
b) When the pilot is alight, extinguish the match and continue to depress for 5 to 10 seconds.
c) The fire may now be controlled as previously described.
5. UPGRADING yOUR FIRE 5.1 Control Type C only
Your fire is fitted with a control valve that can be easily upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local Gazco stockist.
5.2 STANDARD ReMOTe CONTROL This remote control can control the fire after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning GAZCO PART NuMBeR 8455.
5.3 The remote control receiver box is supplied with a 0.8 metre lead, which attaches to the control valve. The receiver must be located in a position that will receive a signal from the handset and may be attached using the adhesive pads supplied in the instruction kit. The receiver must not be located on any surface which may become hot when the fire is in use.
USER INSTRUCTIONS
5.4 IMPORTANT - there is a thermostatic version of the upgrade but this is NOT SuITABLe for open flame fires .
6. ClEANING ThE FIRE
6.1 Cleaning should only be carried out when the fire is turned off and cold.
NOTE: Do not use a vacuum cleaner.
6.2 Cleaning is necessary when there is any chimney debris visible on the coals, or if there is a soot build up in the fire. Minor soot deposits can be ignored.
6.3 Remove the coals or logs carefully onto a sheet of paper.
6.4 Clean the coals or logs using a soft brush taking great care not to damage them.
6.5 Foreign objects or debris which have been thrown, or have fallen onto the fire should be removed when the fire is cold, by hand.
6.6 Replace the ceramic components and coals by referring to section 7.
7. ARRANGEMENT OF FUEl BED COMPONENTS
ADvICE ON hANDlING AND DISPOSAl OF FIRE CERAMICSThe fuel effect and side panels in this appliance are made from Refractory Ceramic Fibre (RCF), a material which is commonly used for this application.Protective clothing is not required when handling these articles, but we recommend you follow normal hygiene rules of not smoking, eating or drinking in the work area and always wash your hands before eating or drinking. To ensure that the release of RCF fibres are kept to a minimum, during installation and servicing a HePA filtered vacuum is recommended to remove any dust accumulated in and around the appliance before and after working on it. When servicing the appliance it is recommended that the replaced items are not broken up, but are sealed within heavy duty polythene bags and labelled as RCF waste.RCF waste is classed as stable, non-reactive hazardous waste and may be disposed of at a licensed landfill site.excessive exposure to these materials may cause temporary irritation to eyes, skin and respiratory tract; wash hands thoroughly after handling the material. NOTE: CERAMIC PARTS ARE FRAGIlE
7.1 General
7.1.1 Your fire will be supplied either with a ceramic Coal, Log, Pebble or Driftwood effect This will have been specified at the time of ordering. With pebble fires follow coal layouts. With driftwood fires follow log layouts.
7
7.1.2 Positioning of ceramic parts is important, not only for the flame effect, but also for optimum performance of the appliance.
7.1.3 It is important that the coals and logs are placed so that there are gaps around each for the flames to pass through.
7.1.4 Ceramic coals or logs must only touch each other at single points, avoid whole sides touching.
7.1.5 Do not use any more ceramic components than those shown, extra parts supplied are spares and should be kept for future use.
7.1.6 The ceramic components should last about 2 years in normal use at which time it is recommended to replace them. Replacement parts can be bought from any stockist who supplies GAZCO fires, always state the model number found on the databadge.
7.1.7 The fuel layout of the Gazco made to measure fires is based on a simple system which is easily adapted to suit the different shapes and sizes available. The parts are supplied in various quantities depending on the size of the fire delivered. Check your coals, pebbles, driftwood and logs. If any are damaged, contact your Gazco stockist for replacements. Always ask for genuine Gazco parts.
7.1.8 Depending on the fuel effect that you have been supplied with, follow the correct section.
7.2 Fire beads and burners
7.2.1 Single burner fires have only one air box and one injector, the burner looks like diagram 4.
4
AR0579
7.2.2 Twin burners have 2 air boxes and 2 injectors; their burners look like diagram 5.
5
AR0593
USER INSTRUCTIONS
7.2.3 Two types of fire beads are supplied, large and small.
7.2.4 using the large fire beads, fill the fire to within 10mm of the top, level and pat down. See diagram 6.
6
AR0580
7.2.5 using the small beads, fill the fire to the top. See diagram 7.
7
AR0581
7.2.6 Smooth out the fire beads, it is important to ensure that the fire is completely filled, level to the top.
NOTE: If your fire needs more beads, then there should be some left over from the original installation, if not then more must be ordered from your Gazco stockist. Do not use any other type of material as this may seriously damage your fire and could be dangerous.
7.2.7 Firmly pat the beads down to ensure that there are no voids left below the surface.
7.2.8 ensure that no beads have fallen into the pilot area.
7.2.9 ensure that the pilot shield is fitted correctly and that it fits tightly onto the edge of the tray. See diagram 8.
8
AR0558
8
USER INSTRUCTIONS
7.3 Coal and Pebble layout (Single burner fires)
7.3.1 Start by placing a small coal or pebble on top of the pilot shield, place small coals or pebbles around the edge of the fire. ensure that there are gaps between each coal or pebble. See diagram 9A.
9A
AR0582
7.3.2 Place pebbles or coals (if coals, use the square coals) in a single layer in the centre of the fire forming a solid mass. Fit together as tightly as possible but not touching the smaller pebbles or coals around the edge. See diagram 9B.
9B
AR0583
7.3.3 Starting at the front, place alternately large and small coals or pebbles around the perimeter of the fire. The coals or pebbles should sit on the first row of small coals or pebbles and rest up against the inner block of square coals. See diagram 9C.
9C
AR0584
7.3.4 Place as many large coals or pebbles that will fit in a single layer on top of the inner block of square coals. ensure that there are gaps between each coal or pebble and that they only touch at single points. Any smaller gap can be filled with a small coal or pebble. See diagram 9D.
9D
AR0589
7.3.5 A few small coals or pebbles can be positioned on top of this layer to complete the effect.
7.4 Coal and Pebble layout (Twin burner fires)
7.4.1 Start by placing a small coal or pebble on top of the pilot shield, place small coals or pebbles around the edge of the fire. ensure that there are gaps between each coal or pebble. See diagram 10A.
10A
AR0585
7.4.2 Place the square coals in a single layer on top of each burner leaving a gap the size of one coal in the middle of each burner and a gap up the centre line of the fire. The coals should fit together as tightly as possible but not touching any of the small moulded coals or pebbles around the edge. See diagram 10B.
10B
AR0586
9
USER INSTRUCTIONS
7.4.3 Starting at the front, place alternately large and small coals or pebbles around the perimeter of the fire. The coals or pebbles should sit on the first row of small coals or pebbles and rest up against the inner block of square coals. See diagram 10C.
10C
AR0587
7.4.4 Place as many large coals or pebbles that will fit in a single layer on top of the inner block of square coals. ensure that there are gaps between each coal or pebble and that they only touch at single points. Bridge the large gaps with the large coals or pebbles, any small gaps left can be filled with a small coal or pebble. See diagram 10D.
10D
AR0588
7.4.5 A few small coals or pebbles can be positioned on top of this layer to complete the effect.
7.5 log and Driftwood layout
7.5.1 Identify the logs or driftwood that you have been supplied with. See diagram 11 and Spares List on page 41.
Note: The log number will be suffixed DW for driftwood effect ceramics
11
AR0588
Identify which of the illustrated layouts best suits the size of the fire you have and the logs or driftwood you have been sent.
SMAll FIRES
12
AR0575AR0574
AR0578AR0577
7.5.2 Place two logs as shown. See diagram 12A.
7.5.3 Place the log as shown. See diagram 12B.
7.5.4 Place the rest of the lower layer of logs as shown. See diagram 12C.
7.5.5 Place the second layer of cross logs as shown. See diagram 12D.
10
USER INSTRUCTIONS7.5.6 You may have been supplied some smaller logs or cones
which are provided to finish off the layout.
MEDIUM FIRES
13
AR0567AR0566
AR0569AR0568
7.6.1 Place two logs as shown. See diagram 13A.
7.6.2 Place the logs as shown. See diagram 13B.
7.6.3 Place the rest of the lower layer of logs as shown. See diagram 13C.
7.6.4 Place the second layer of cross logs as shown. See diagram 13D.
7.6.5 You may have been supplied some smaller logs or cones which are provided to finish off the layout.
lARGE FIRES
14
AR0571AR0570
AR0573AR0572 lOG
SET
S U
SED
ON
GAz
CO
FIR
ES D
EvEl
OPE
D F
ROM
Th
E M
TM R
ANG
E
Lo
g N
umbe
r A1
A2
B1
B2
1 4
5 6
7 8
9 11
12
13
14
(D
W)
Des
crip
tion
Gaz
co N
o. C
e 022
0 02
21
0222
02
23
0224
02
25
0226
02
27
0228
02
29
0230
02
31
0232
02
33
0234
(D
W)
(P)8
106,
(P)8
135,
(P)8
143,
Adam
, Cha
tsw
orth
, Pub
Sce
ne
(P
)817
4, (P
)811
9,
0 0
1 0
1 0
0 1
2 2
1 1
0 2
1 S/
Span
ish, S
/Asp
en, S
/Cha
mon
ix
(P
)812
9 (P
)813
0, (P
)813
6, (P
)814
4,
(P
)812
0
1 0
0 0
1 0
0 2
3 2
0 0
0 2
2 L/
Span
ish, L
/Asp
en, S
/Cha
mon
ix
(P)
8021
0 0
0 1
1 0
0 1
2 2
1 1
0 2
0 Sm
all C
rom
wel
l (P
)802
2
1 0
0 0
1 0
0 1
3 2
1 0
0 2
2 La
rge
Cro
mw
ell
(P)8
125
1
0 0
0 1
0 0
1 2
2 2
0 0
2 2
18" B
OD
(P)8
126
0
0 0
2 1
0 0
1 1
2 2
2 0
2 2
20" B
OD
(P)8
018
1
0 0
0 1
0 0
2 3
2 0
0 0
2 2
18" S
wan
s N
est
(P)8
019
1
1 0
0 3
0 2
2 1
1 1
2 1
2 1
24" S
wan
s N
est
(P)8
020
1
1 1
1 3
2 2
2 2
2 0
2 0
2 2
36" S
wan
s N
est
(P)8
142
0
0 0
0 1
0 0
0 1
2 2
2 0
2 1
Dav
os
* dr
iftw
ood
fires
the
log
num
ber
& C
e nu
mbe
r ar
e fo
llow
ed b
y D
W
11
USER INSTRUCTIONS
7.7.1 Place two logs as shown. See diagram 14A.
7.7.2 Place the logs as shown. See diagram 14B.
7.7.3 Place the rest of the lower layer of logs as shown. See diagram 14C.
7.7.4 Place the second layer of cross logs as shown. See diagram 14D.
7.7.5 You may have been supplied some smaller logs or cones which are provided to finish off the layout.
8. OxyGEN DEPlETION SENSOR
8.1 The appliance is fitted with an oxygen sensitive pilot system that will act to cut off the gas supply to the fire should the oxygen in the room fall below its normal level. If the fire is turned off by this device, it usually indicates that there is a problem with the flue system, and this should be inspected by a qualified engineer.
Do not attempt to use the fire until an engineer says it is safe to do so.
This device is not a substitute for an independently mounted carbon monoxide detector.
9.1 This is a safety feature incorporated in all GAZCO fires which automatically switches off the gas supply if the pilot goes out and fails to heat the thermocouple.
10. RUNNING IN
10.1 The surface coating on the coals used in your GAZCO fire will "burn off" during the first few hours of use producing a harmless and temporary odour. This will disappear after a short period of use. If the odour persists, ask your installer for advice.
11. SERvICING
11.1 The fire must be serviced every 12 months by a qualified Gas engineer. In all correspondence always quote the appliance type and the serial number which may be found on the databadge, adjacent to the control knob.
12
INSTAllATION INSTRUCTIONSTEChNICAl SPECIFICATION
FIRES FITTED WITh SEAGAS & BABySIT vAlvECOvERING ThE FOllOWING MODElS
SP & PSP MTM FIReSSWANS NeST BASKeTS
INJeCTOR HIGH BuRNeR PReSSuRe LOW BuRNeR PReSSuRe
Mbar Mbar Mbar Mbar Mbar Mbar
MODeL NO. VALVe INLeT NG LPG INPuT G20 G30 G31 INPuT G20 G30 G31 A Seagas 8mm 800 400 6kW 3.3 4.1 6.2 3kW 0.9 1 2.5
A1RD A2RD B1RD CIRD D1RD Seagas 8mm 800 400 7kW 4.6 5.9 8 3.5kW 1.3 1.5 3.3
A1 Seagas 8mm 800 400 8kW 6.0 7.25 10.1 4kW 1.7 1.9 3.6
A2 B1 Seagas 8mm 800 400 9kW 8.0 9.5 13.2 4.5kW 2.2 2.5 4
A3 B2 C1 Seagas 8mm 800 400 10kW 10.5 11.5 16.2 5kW 3.0 2.9 4.6
A4 B3 C2 D1 Seagas 8mm 1100 400 11kW 6.4 13 19.3 5.5kW 1.8 3.2 5.3
A5 B4 C3 D2 e1 Seagas 8mm 1100 400 12kW 7.9 16.5 22.6 6kW 2.1 4.1 6.2
A6 B5 C4 D3 e2 F1 Seagas 8mm 1600 400 13kW 2.4 19.1 26.5 6.5kW 1.0 4.9 7
A7 B6 C5 D4 e3 F2 G1 Seagas 8mm 1600 400 14kW 3.4 22 30.4 7kW 1.2 5.9 8
B7 C6 D5 e4 F3 G2 H1 Seagas 8mm 1600 600 15kW 4.3 13 17.5 7.5kW 1.5 3 5
C7 D6 e5 F4 G3 H2 H3 I1 I2 I3 J1 Seagas 8mm 1600 600 16kW 5.5 14.9 20 8kW 1.7 3.5 5.6
DD1 Babysit 10mm 1600 400 15.2kW 1.9 7 9.8 7.6kW 0.6 1.6 2.8
BB4 DD2 ee1 Babysit 10mm 1600 400 16.8kW 2.3 8.5 11.7 8.4kW 0.7 2.4 3.5
AA6 BB5 CC4 DD3 ee2 FF1 Babysit 10mm 1600 400 18.5kW 2.8 9.6 14.2 9.25kW 0.9 3 3.9
AA7 BB6 CC5 DD4 ee3 FF2 GG1 Babysit 10mm 1600 400 20.2kW 3.2 12 16.8 10.1kW 1.0 3.1 4.8
AA8 BB7 CC6 DD5 ee4 FF3 GG2 Babysit 10mm 1600 400 21.9kW 3.6 12.8 19.3 10.95kW 1.1 3.5 5.5
BB8 CC7 DD6 ee5 FF4 GG3 Babysit 10mm 1600 400 23.6kW 4.0 15.6 22.4 11.8kW 1.3 3.9 6
CC8 DD7 ee6 FF5 GG4 Babysit 10mm 1600 600 25.3kW 4.5 10 14.6 12.65kW 1.4 2.6 4.8
DD8 ee7 FF6 GG5 Babysit 10mm 1600 600 26.9kW 5.0 11 15.6 13.45kW 1.5 2.9 5.3
ee8 FF7 GG6 Babysit 15mm 1600 600 28.6kW 5.7 12 17.6 14.3kW 1.7 3.2 5.8
FF8 GG7 Babysit 15mm 1600 600 30.3kW 6.5 13.25 20.2 15.15kW 1.9 3.5 6.3
GG8 Babysit 15mm 1600 600 32kW 6.9 15.5 21.6 16kW 2.0 4.25 7
All fires have pre set High and Low gas pressure settings.*If adjustments are made on site the adjusting screw must be sealed.*with the exception of extended controls away from the fire.
SEAGAS - Type A BABySIT - Type B
Gas CAT Gas Type WorkingPressure mb Aeration Country
12H Natural Gas G20 20 7.5mm GB & Ie
13+LPG Butane G30 29 3 x 15mm GB & Ie
LPG Propane G31 31
13
INJeCTOR HIGH SeTTING PReSSuRe LOW SeTTING PReSSuRe
Nat Gas Butane Propane Nat Gas Butane Propane
(G20) (G30) (G31) (G20) (G30) (G31)
BuRNeR VALVe INLeT NG LPG INPuT 20mb 29mb 37mb INPuT 20mb 29mb 37mb A2RD Mertik 8mm 800 400 7kW 5.8 5.8 7.5 3.5kW 1.6 1.6 2.0
C1RD Mertik 8mm 800 400 7kW 5.8 5.8 7.5 3.5kW 1.6 1.6 2.0
B1 Mertik 8mm 800 400 9kW 9.4 9.3 11.8 4.5kW 2.6 2.6 3.4
B2 C1 Mertik 8mm 800 400 10kW 11.6 12.1 15.5 5.0kW 3.3 3.3 4.2
B3 C2 Mertik 8mm 1100 400 11kW 7.6 14.0 18.0 5.5kW 2.2 3.9 5.0
B4 C3 D2 Mertik 8mm 1100 400 12kW 9.0 16.3 21.1 6.0kW 2.6 4.6 6.0
B5 C4 D3 e2 Mertik 8mm 1600 400 13kW 5.4 20.0 25.3 6.5kW 1.7 5.6 7.0
B6 C5 D4 e3 F2 Mertik 8mm 1600 400 14kW 6.3 21.9 28.0 7.0kW 2.0 5.9 7.2
B7 C6 D5 e4 F3 G2 Mertik 8mm 1600 600 15kW 7.7 14.1 18.0 7.5kW 2.4 3.9 5.1
C7 D6 e5 F4 G3 H2 H3 I2 I3 Mertik 8mm 1600 600 16kW 8.3 15.7 20.5 8.0kW 2.6 4.3 5.6
GAS FLOW RATe m3/hr (Gross)
HIGH RATe LOW RATe
GAS CAT. 12H 13+ 12H 13+
GAS TYPe G20 G30 G31 G20 G30 G31
PReSSuRe 20 29 37 20 28 37 A2RD 0.66 0.20 0.25 0.33 0.10 0.12
C1RD 0.66 0.20 0.25 0.33 0.10 0.12
B1 0.85 0.25 0.33 0.42 0.13 0.17
B2 C1 0.94 0.28 0.36 0.48 0.14 0.18
B3 C2 1.04 0.31 0.39 0.52 0.15 0.20
B4 C3 D2 1.11 0.34 0.43 0.56 0.17 0.22
B5 C4 D3 e2 1.21 0.36 0.48 0.61 0.18 0.24
B6 C5 D4 e3 F2 1.32 0.39 0.51 0.66 0.20 0.25
B7 C6 D5 e4 F3 G2 1.39 0.42 0.54 0.69 0.21 0.27
C7 D6 e5 F4 G3 H2 H3 I2 I3 1.51 0.45 0.58 0.76 0.23 0.29
INSTAllATION INSTRUCTIONSTEChNICAl SPECIFICATION
FIRES FITTED WITh MERTIK MAxITROl vAlvECOvERING ThE FOllOWING MODElS
SP & PSP MTM FIReSGAS FIReS uSeD IN STOVAx CLASSIC FIRePLACeSGAS FIReS IN THe GAZCO BASKeT FIReS RANGe
Fires with Mertik Maxitrol Valves are pre set & are not adjustable
MERTIK MAxITROl - Type C
14
INSTAllATION INSTRUCTIONSSITE REQUIREMENTS
1. FlUE AND ChIMNEy REQUIREMENTS 1.1 The flue must be installed in accordance with all local and
national regulation and the current rules in force.
1.2 Fireplace opening up to 450mm (18") wide by 600mm (24") high will usually work with a 175mm (7") diameter flue. Larger openings will require bigger flues. See diagram 1 as a guide.
AR0595AR0596
A
B
D
C
A
B
C
D
1
mm mm cm2 C A B A x B 3.0m 4.5m 6.0m 9.0m 15.0m 350 550 1925cm2 175 175 175 175 175 400 550 2200cm2 175 175 175 175 175 460 460 2116cm2 175 175 175 175 175 460 550 2530cm2 200 175 175 175 175 460 610 2806cm2 200 200 175 175 175 610 460 2806cm2 200 200 175 175 175 610 610 3721cm2 250 225 200 200 175 610 760 4636cm2 300 250 250 225 200 760 460 3496cm2 225 225 200 200 175 760 610 4636cm2 250 250 250 225 200 760 760 5776cm2 300 300 250 250 225 760 910 6916cm2 350 300 300 250 250 910 460 4186cm2 250 225 225 200 200 910 610 5551cm2 300 300 250 250 225 910 760 6916cm2 350 300 300 250 250 910 910 8281cm2 350 350 300 300 250 910 1070 9737cm2 - 350 350 300 300 1070 460 4922cm2 300 250 250 225 200 1070 610 6527cm2 300 300 300 250 250 1070 760 8132cm2 350 350 300 300 250 1070 910 9737cm2 • 350 350 300 300 1070 1070 11449cm2 • • 350 350 300 1070 1220 13054cm2 • • • 350 350 1220 460 5612cm2 300 300 250 250 225 1220 610 7442cm2 350 300 300 300 250 1220 760 9272cm2 • 350 350 300 300 1220 910 11102cm2 • • 350 350 300 1220 1070 13054cm2 • • • 350 350 1220 1220 14884cm2 • • • 350 350 1520 460 6992cm2 300 300 300 250 250 1520 610 9272cm2 • 350 350 300 300 1520 760 11552cm2 • • 350 350 300 1520 910 13831cm2 • • • 350 350 1520 1070 16264cm2 • • • • 350 1520 1220 18544cm2 • • • • •
1.3 The chimney or flue must be free from any obstruction. Any damper plates should be removed or secured in the fully open position, and no restrictor plates should be fitted.
1.4 The chimney should be swept prior to the installation of the appliance - unless it can be seen to be clean and unobstructed throughout its entire length.
1.5 ensure that there is a smooth tapered transition from the fireplace opening into the chimney or flue.
1.6 The flue pull should be checked prior to installation of the appliance. Apply a smoke pellet to the flue or chimney opening and ensure that the smoke is drawn into the opening. If there is not a definite flow, pre-heat the chimney for a few minutes and re-test the flow.
IF ThERE IS STIll NO DEFINITE FlOW, ThE ChIMNEy MAy REQUIRE ATTENTION - SEEK ExPERT ADvICE.
2. INSTAllATION OF ThE GAS SUPPly
2.1 Before installation, ensure that the local distribution conditions (identification of the type of gas and pressure) and the adjustment of the appliance are compatible.
2.2 ensure that the gas supply is capable of delivering the required amount of gas, and is in accordance with the rules in force.
2.3 Soft copper tubing and soft soldered joints can be used, but must not be closer than 50mm (2") to the base of the tray.
2.4 A means of isolating the gas supply to the appliance must be provided independent of any appliance control.
2.5 All supply gas pipes must be purged of any debris that may have entered prior to connection to the appliance.
3. vENTIlATION
It is important to ensure that any national ventilation requirements are taken into account during the installation of this appliance.
3.1 All Gazco MTM fires with a heat input greater than 7kw require an air vent of at least 100 cm2 effective area or 4.5 cm2 for every kw over 7kw, whichever is the greater.
3.2 Fires with a heat input of 7kW or less do not normally require an air vent but some countries still demand ventilation so check local regulations. Decorative flame effect fires with a heat input greater that 20kW net require an extra 5cm2 ventilation per additional kilowatt (i.e. a 32kW fire requires 160cm2).
3.3 Those fires with a heat input of less than 7kw do not normally require an air vent but some countries still require ventilation, check local standards.
D
15
3.3 It is essential to check for flue clearance, see section 16. If spillage is detected, it may be necessary to provide additional ventilation.
3.4 The ventilation is in addition to any openable window, and although it must communicate with the outside air, wherever possible, it can communicate with an adjacent room provided that the space has a similar vent to the outside.
4. APPlIANCE lOCATION
4.1 This appliance must stand on a non-combustible hearth that is at least 12mm thick.
4.2 It must be fitted into a non-combustible opening.
4.3 These appliances must be hearth mounted into a fireplace opening conforming to National Standards.
4.4 The appliance must be firmly fixed to the hearth.
4.5 ensure that no naked flame or incandescent part of the fire bed projects beyond the vertical plane of the fireplace opening.
4.6 The appliance must not be installed in any room that contains a bath or shower.
4.7 ensure clearances to combustible materials. See diagram 2.
2
AR0501
INSTAllATION INSTRUCTIONSSITE REQUIREMENTS
5. CONTROlS
5.1 This appliance will be supplied with one of the following options
a) Controls which are factory fixed and ready to install. Mertik Maxitrol upgradeable valve a limited range of fires are fitted with this valve, a Seagas or a Babysit valve.
With Seagas or Babysit valve only. b) Separate controls which go under the fire, supplied with
short pre-bent pipes. c) Separate controls which can be mounted away from the
fire, supplied with 1.5m coiled pipe.
6. CONTROl UPGRADE
6.1 A limited range of fires are available with a control valve that can be easily upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local GAZCO stockist.
6.2 STANDARD ReMOTe CONTROL This remote control can control the fire after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning. GAZCO PART NuMBeR 8455.
16
IMPORTANT:eNSuRe THAT THe APPLIANCe IS CORReCTLY ADJuSTeD FOR THe GAS TYPe AND CATeGORY APPLICABLe IN THe COuNTRY OF uSe. ReFeR TO DATABADGe AND TeCHNICAL SPeCIFICATIONS AT THe FRONT OF THe BOOKLeT.
FOR DeTAILS OF CHANGING BeTWeeN GAS TYPeS ReFeR TO SeCTION 22.
1. SAFETy PRECAUTIONS
1.1 This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space. Please read these instructions before installation and use of this appliance.
1.2 These instructions must be left intact with the user.
1.3 Do not attempt to burn rubbish on this appliance.
1.4 In your own interest, and those of safety, this appliance must be installed by competent persons in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution.
1.5 Keep all plastic bags away from young children.
2. ODS PIlOT REQUIREMENTS The following are special requirements for air supply to the
O.D.S. assembly and to the underside of the appliance.
FAIlURE TO COMPly WITh ThESE REQUIREMENTS MAy AFFECT ThE SAFETy OF ThIS APPlIANCE.
2.1 Place the fire into its intended position, together with any fret front, ash cover, cast iron parts, fire grates or any other parts which are to be placed in front of the fire.
2.2 ensure that there is a clear space at least equivalent to that shown in diagram 1 in front of the lower half of the pilot shield.
1
100
100100
25
15
AR0243
2.3 In addition to 2.2 above, ensure that there is ventilation under the appliance is at least equivalent to that shown in diagram 1.
INSTAllATION INSTRUCTIONSINSTAllATION
2.4 If any amendments are necessary to comply with 2.2 or 2.3 above then these MuST be made before commissioning the appliance.
3. UNPACKING
3.1 Remove the appliance from its packaging, and check that it is complete and undamaged.
3.2 Put the loose ceramic parts to one side so that they are not damaged during installation.
4. INSTAllATION
This appliance will be supplied with one of the following options:
4.1 Controls which are factory fixed and ready to install: There are 3 different valves which can be supplied with
your fire, it is important to identify which control you have.
Control Type A - Seagas valve
2
Seagas Valve
Control Type B - Babysit valve
3
Babysit Valve
With Seagas or Babysit valve - start installation from section 5
4.2 Separate controls which go under the fire, supplied with short pre-bent pipes - start installation from section 6.
4.3 Separate controls which can be mounted away from the fire, supplied with 1.5m coiled pipe - start installation from section 7.
17
Control Type C - Mertik Maxitrol valve
4
AR0914
With Mertik Maxitrol Upgradeable valve - Start installation from section 13.
5. FIxED CONTROlS UNDER FIRE
5.1 Control Types A & B - Seagas & Babysit Only
Position the fire into its intended location and mark the front leg fixing holes. Remove the fire and drill the holes to accept the plugs provided. Refit the fire and screw down onto the hearth. See diagram 5.
5
AR0622
5.2 "HAVe YOu PuRGeD THe GAS SuPPLY PIPeS?" This is essential to expel any foreign matter that might get blown into the valve assembly causing blockages
5.3 Remove the gas control knob and remove the fascia plate by undoing the two screws. See diagram 6.
6
AR0597
AR0623
AR0598
AR0624
5.4 Connect the gas supply pipe to the 8mm connection. See diagram 7.
7
AR0543
AR0544
5.5 Go to section 11.3.
INSTAllATION INSTRUCTIONSINSTAllATION
18
9. SEPARATE CONTROlS UNDER ThE FIRE
9.1 Control Types A & B - Seagas & Babysit Only
Preliminary work
9.1.1 Mark required position of the front of the tray on the hearth. See diagram 5.
NOTe: The front of the fire must not project beyond the front of the fireplace opening.
9.1.2 Mark the required centre line of the fire on the hearth. See diagram 8.
8
AR0243
9.1.3 Remove the fascia from the controls. See diagram 9.
9
AR0623
AR0597 AR0598
AR0624
9.1.4 There are two types of valve, see diagram 9.
Seagas or Babysit The Babysit valve can be supplied with either 8mm, 10mm
or 15mm pipe depending on the size of the fire. Identify the valve you have and the pipe sizes it uses and
follow the correct section below. NOTE: THe SuMMARY CHART ON THe INSIDe FRONT
COVeR GIVeS THe VALVe TYPe & INLeT CONNeCTION SIZe FOR eACH MODeL NuMBeR.
a) Seagas & Babysit with 8mm pipe fittings Place the controls with the front flush with the line on the
hearth and the notch in line with the marked centre line. ensure that the fire front or ash cover will fit without fouling the control knob; if it does, move the controls further back (up to 20mm). This will also require an easy amendment to the pilot pipe detailed in later sections. Mark the two fixing holes. See diagram 10.
10
AR0599
b) Babysit with 10mm pipe fittings Place the controls with the front flush with the line on the
hearth and the left-hand side of the controls flush with the centreline. ensure that the fire front or ash cover will fit without fouling the control knob; if it does, move the controls further back (up to 20mm). This will also require an easy amendment to the pilot pipe detailed in later sections. Mark the two fixing holes. See diagram 11.
INSTAllATION INSTRUCTIONSINSTAllATION
19
11
AR0600
c) Babysit with 15mm pipe fittings
Place the controls with the front flush with the line on the hearth and the left-hand side of the controls 140mm to the right of the centreline. ensure that the fire front or ash cover will fit without fouling the control knob; if it does, move the controls further back (up to 20mm). This will also require an easy amendment to the pilot pipe detailed in later sections. Mark the two fixing holes. See diagram 12.
12
AR0601
NOTE: IF YOuR FIRe IS SuPPLIeD WITH LeGS, FOLLOW 9.1.5 BeLOW, IF NOT GO TO 9.1.6.
9.1.5 Place the fire with the front edge lining up with the line marked on the hearth. ensure that the fire is central about the centre line marked on the hearth. Mark the two fixing holes. See diagram 13.
13
AR0542
9.1.6 Drill & plug the fixing holes.
9.1.7 Screw the controls to the hearth. See diagram 11, 12 & 13 as appropriate.
9.1.8 Identify the size of the pipe fitting supplied at the valve inlet, 8mm, 10mm or 15mm. Install the gas supply to the controls. ensure the correct size is used. Read section 2.
9.1.9 "HAVe YOu PuRGeD THe GAS SuPPLY PIPeS?" This is essential to expel any foreign matter that might get blown into the valve assembly causing blockages.
9.1.10 Connect the gas supply to the valve inlet. See diagram 14A.
9.1.11 unroll the thermocouple and lay the pilot in front of the controls. See diagram 14B.
14
AR0544
AR0543
INSTAllATION INSTRUCTIONSINSTAllATION
20
9.2 Pilot connection (Seagas valves)
9.2.1 If your fire is supplied with legs, secure it to the hearth using the screws provided. See diagram 15.
15
AR0542AR0622
If your fire is supplied with studs and brackets, then use these to secure into the basket or hearth. See diagram 16.
16
AR0545
ensure that the front of the fire lines up with the line marked on the hearth and that it is central about the centre line marked on the hearth.
9.2.2 Loosely connect the pilot pipe to the valve and rest it against the front of the fire. ensure that the pilot pipe passes between the 2 pilot fixing holes and mark the position of the base of the tray. See diagram 17.
INSTAllATION INSTRUCTIONSINSTAllATION
17
AR0546
NOTE: IF IT WAS NeCeSSARY IN SeCTION 9.1.4 TO FIx THe CONTROLS FuRTHeR BACK, THe PILOT PIPe MAY NeeD FuRTHeR BeNDING TO BRING IT INTO THe CORReCT POSITION.
9.2.3 Subtract 3mm & cut to length, see diagram 18. De-burr and blow the filings out of the pipe.
18
AR0546
9.2.4 Screw the pilot to the front of the fire, engaging the pilot pipe at the same time. See diagram 19.
19
AR0548
21
INSTAllATION INSTRUCTIONSINSTAllATION
Tighten the pilot tube fittings at both ends using the fittings supplied and coil any excess thermocouple neatly under the fire.
9.3 Pilot connection (Babysit valves)
9.3.1 Loosely attach the pilot pipe at the rear of the valve using the fitting provided. See diagram 20,arrow C. Position the pilot pipe so that it is vertical at the front of the fire.
20
AR0544
AR0543
9.3.2 Temporarily place the fire into its final position making sure that its front edge lines up with the line marked on the hearth and that it is central about the centre line marked on the hearth. ensure that the pilot pipe passes between the 2 pilot fixing holes and mark the position of the base of the tray. See diagram 21.
21
AR0546
NOTe: If it was necessary in section 9.1.4 to fix the controls further back, the pilot pipe may need further bending to bring it into the correct position.
9.3.3 Remove the fire and the pilot pipe and subtract 3mm and cut, de-burr and blow the filings out of the pipe. See diagram 22.
22
AR0547
Tighten the pilot pipe back into the back of the valve, ensure that the pipe is still vertical at the front.
9.3.4 If your fire is supplied with legs, secure it to the hearth using the screws provided. See diagram 23.
23
AR0542AR0622
If your fire is supplied with studs and brackets, then use these to secure into the basket or heart. See diagram 24.
24
AR0545
ensure that the front of the fire lines up with the line marked on the hearth and that it is central about the centre line marked on the hearth.
22
INSTAllATION INSTRUCTIONSINSTAllATION
9.3.5 Screw the pilot to the front of the fire engaging the pilot pipe at the same time. See diagram 25.
25
AR0545
Check that the tube is fully engaged into the pilot and tighten the fitting. Coil the thermocouple neatly under the fire.
9.3.6 If 8mm fittings, go to section 9.4, 10mm & 15mm fittings go to section 9.5.
9.4 Gas feed connection (Babysit 8mm Fittings)
9.4.1 Loosely connect the gas feed pipe into the left-hand side of the control and mark the pipe just below the base of the tray. See diagram 26, arrow A.
26
AR0550
9.4.2 Cut the pipe at this mark and then rotate it until it rests behind the injector, mark the position as shown in diagram 27, arrow B.
27
AR0551
9.4.3 Add 5mm and cut to length, see diagram 28.
28
AR0552
Now connect the pipe at both ends using nuts and olives and tighten.
9.5 Gas feed connection (Babysit 10mm & 15mm fittings)
9.5.1 Loosely connect the gas feed pipe into the left-hand side of the control and mark the pipe at the ‘T’ piece fitting. See diagram 29, arrow A.
29
AR0553
23
INSTAllATION INSTRUCTIONSINSTAllATION
9.5.2 Add 10mm and cut to length. See diagram 30, arrow B.
30
AR0554
Now connect the pipe at both ends using the fittings provided and tighten.
9.5.3 Go to section 11.
10. SEPARATE CONTROlS AWAy FROM ThE FIRE
10.1 Control Types A & B - Seagas & Babysit Only
Preliminary
10.1.1 Mark required position of the front of the tray on the hearth. See diagram 31.
31
AR0542AR0622
NOTE: THe FRONT OF THe FIRe MuST NOT PROJeCT BeYOND THe FIRePLACe OPeNING.
10.1.2 Mark the required centre line of the fire on the hearth. See diagram 32.
10.1.3 Decide where the controls are going to be fitted; note that the thermocouple is 1.5m long maximum and must be able to reach from the intended control position to the pilot on the fire. Check this carefully before proceeding.
10.1.4 Remove the cover for the controls. See diagram 32.
32
AR0623
AR0597 AR0598
AR0624
10.1.5 Attach the controls to a firm surface using the fixing points and fasteners provided. See diagram 33.
33
AR0600AR0599
AR0601
10.1.6 Identify the size of pipe fitting supplied at the valve inlet, 8mm, 10mm or 15mm. Install the gas supply to the controls. ensure the correct size of pipe is used. See section 4.
10.1.7 "HAVe YOu PuRGeD THe GAS SuPPLY PIPeS?" This is essential to expel any foreign matter that might get blown into the valve assembly causing blockages.
24
INSTAllATION INSTRUCTIONSINSTAllATION
10.1.8 Connect the gas supply to the valve inlet. See diagram 34, arrow A.
34
AR0557AR0556
10.2 Pilot connection
NOTE: IF YOuR FIRe IS SuPPLIeD WITH LeGS, FOLLOW SeCTION 10.2.1 BeLOW, IF NOT GO TO SeCTION 10.2.3.
10.2.1 Place the fire with the front edge lining up with the line marked on the hearth. ensure that the fire is central about the centre line marked on the hearth. Mark the two fixing holes. See diagram 35.
35
AR0542AR0622
10.2.2 Drill and plug the fixing holes, screw the fire to the hearth with the fasteners provided.
10.2.3 If your fire is supplied with studs and brackets, then use these to secure it into the basket or hearth. See diagram 36.
36
AR0545
ensure that the front of the fire lines up with the line marked on the hearth and that it is central about the centre line marked on the hearth.
10.2.4 unroll the thermocouple from the pilot and route it from the fire to the controls. Attach the thermocouple into the back of the gas valve. Do not overtighten. See diagram 37, arrow B.
37
AR0557AR0556
10.2.5 Screw the pilot to the front of the fire. See diagram 38.
38
AR0556
10.2.6 uncoil the 4mm pilot tube and route it from the fire to the controls. Connect to the valve with the fittings provided, see diagram 34, arrow C. Cut the pipe to length and attach to the pilot using the fitting provided. See diagram 38.
10.3 Gas feed connection
10.3.1 uncoil the 8mm or 10mm gas feed pipe and route it from the controls to the ‘T’ fitting on the fire. Where the controls use 8mm or 10mm pipe, Gazco supplies 1.5 metres for this purpose. Do not kink the pipe.
NOTE: GAZCO DOeS NOT SuPPLY 15MM PIPe, THIS IS ReADILY AVAILABLe AT YOuR LOCAL HARDWARe STORe.
25
INSTAllATION INSTRUCTIONSINSTAllATION
10.3.2 Connect the gas feed pipe to the control, (see diagram 37, arrow D) and to the ‘T’ fitting on the fire using the fittings provided.
10.3.3 Go to section 11.
11. FINIShING OFF
11.1 Connect the ignition lead to the pilot as shown in diagram 36. Keep the ignition lead away from the pipework as it will jump to earth over the 1.5m rather than the electrode i.e. do not feed through the same hole.
39
AR0097
ensure that the insulation is in the position shown and that the spark gap is correct.
11.2 use the cable ties to tidily hold the thermocouple and pilot pipe together if required.
11.3 Turn on the gas and leak test all joints up to the valve body. Light the pilot and using leak detection fluid, check both joints. Light the burner and check all joints from the valve to the injector. Correct any leaks.
12. BURNER PRESSURE
12.1 Control Types A & B - Seagas & Babysit Only
IMPORTANT
All fires have pre set High and Low gas settings. (With the exception of fires with extended controls, that must be set on site).
The correct burner pressures are stated on the databadge and in the technical specification section in this book.
The settings should be checked on site, and the adjusting screws sealed on completion.
40
AR0561
AR0560
AR0559
12.2 Run the fire on maximum setting and adjust the high rate screw until the correct high setting burner pressure is achieved. See diagram 40, arrow B.
12.3 Turn the fire onto minimum and adjust the low rate screw until the correct low setting burner pressure is achieved. See diagram 40, arrow C.
12.4 Replace the fascia and control knob where appropriate.
12.5 The adjusting screw must be sealed when set.
All MTM Fires work on a gas inlet pressure of 20mb on Natural Gas, 28mb on Butane and 37mb on Propane with the fire on full.
13. CONTROl TyPE C ONly
Type C - Metrik Maxitrol Upgradeable valve Only
A limited range of fires are fitted with this valve. These fires have preset High and Low settings with a Gas
working pressure as listed below with the fire on full. 20mb on Natural Gas, 28mb on Butane and 37mb on
Propane with the fire on full.
IMPORTANT: eNSuRe THAT THe APPLIANCe IS CORReCTLY ADJuSTeD FOR THe GAS TYPe AND CATeGORY APPLICABLe IN THe COuNTRY OF uSe. ReFeR TO DATABADGe AND TeCHNICAL SPeCIFICATIONS AT THe FRONT OF THe BOOKLeT.
FOR DeTAILS OF CHANGING BeTWeeN GAS TYPeS ReFeR TO SeCTION 8 RePLACING PARTS.
26
INSTAllATION INSTRUCTIONSINSTAllATION
The appliance must be firmly fixed to the hearth. Fasteners are provided for this purpose.
All supply gas pipes must be purged of any debris that may have entered prior to connection to the appliance.
13.1 Connect the gas supply to the 8mm compression elbow situated to the right of the valve. See diagram 41.
41
AR1113
If the isolation tap is to be fitted under the fire, the GAZCO GC00060 provides a neat and easy solution.
14. CONTROl UPGRADE
14.1 Your fire is fitted with a control valve that can be easily upgraded to battery powered remote control. This upgrade can be fitted by anyone capable of simple DIY jobs and requires no special training. This upgrade can be obtained through your local GAZCO stockist.
14.2 STANDARD ReMOTe CONTROL This remote control can control the fire after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning. GAZCO PART NuMBeR 8455.
14.3 The remote control receiver box is supplied with a 0.8 metre lead which attaches to the control valve. The receiver must be located in a position that will receive a signal from the handset and may be attached using the adhesive pads supplied in the instruction kit. The receiver must not be located on any surface which may become hot when the fire is in use.
14.4 IMPORTANT - there is a thermostatic version of the upgrade but this is NOT SuITABLe for open flame fires.
15. FUElBED ARRANGEMENT
ADvICE ON hANDlING AND DISPOSAl OF FIRE CERAMICS
The fuel effect and side panels in this appliance are made from Refractory Ceramic Fibre (RCF), a material which is commonly used for this application.
Protective clothing is not required when handling these articles, but we recommend you follow normal hygiene rules of not smoking, eating or drinking in the work area and always wash your hands before eating or drinking.
To ensure that the release of RCF fibres are kept to a minimum, during installation and servicing a HePA filtered vacuum is recommended to remove any dust accumulated in and around the appliance before and after working on it. When servicing the appliance it is recommended that the replaced items are not broken up, but are sealed within heavy duty polythene bags and labelled as RCF waste.
RCF waste is classed as stable, non-reactive hazardous waste and may be disposed of at a licensed landfill site.
excessive exposure to these materials may cause temporary irritation to eyes, skin and respiratory tract; wash hands thoroughly after handling the material.
15.1 Single burner fires have only one air box and one injector, the burner looks like diagram 42.
42
AR0579
15.2 Twin burners have 2 air boxes and 2 injectors; their burners look like diagram 43.
43
AR0593
15.3 Two types of fire beads are supplied, large and small.
27
INSTAllATION INSTRUCTIONSINSTAllATION
15.4 using the large fire beads, fill the fire to within 10mm of the top, level and pat down. See diagram 44.
44
AR0580
15.5 using the small beads, fill the fire to the top, see diagram 45.
45
AR0581
15.6 Smooth out the fire beads, it is important to ensure that the fire is completely filled, level to the top.
NOTE: If your fire needs more beads, then there should be some left over from the original installation, if not then more must be ordered from your Gazco stockist. Do not use any other type of material as this may seriously damage your fire and could be dangerous.
15.7 Firmly pat the beads down to ensure that there are no voids left below the surface.
15.8 ensure that no beads have fallen into the pilot area.
15.9 ensure that the pilot shield is fitted correctly and that it fits tightly onto the edge of the tray, see diagram 46.
46
AR0588
NOTE - CERAMIC PARTS ARE FRAGIlE
15 General
15.1.1 Your fire will be supplied either with a ceramic log, pebble or a coal effect. This will have been specified at the time of ordering.
15.1.2 Some fires can either be log, pebble or coal effect but smaller fires can only be coal or pebble effect and large fires can only be log effect.
15.1.3 Positioning of ceramic parts is important, not only for the flame effect, but also for optimum performance of the appliance.
15.1.4 It is important that the coals, pebbles and logs are placed so that there are gaps around each for the flames to pass through.
15.1.5 Coals, pebbles and logs must only touch another at single points, avoid whole sides touching.
15.1.6 Do not use any more coals and logs than those shown, extra parts supplied are spares and should be kept for future use.
15.1.7 The ceramic coals, pebbles and logs should last about 2 years in normal use at which time it is recommended to replace them. Replacement parts can be bought from any stockist who supplies GAZCO fires, always state the model number found on the databadge.
15.1.8 The fuel layout of the Gazco made to measure fires is based on a simple system which is easily adapted to suit the different shapes and sizes available. The parts are supplied in various quantities depending on the size of the fire delivered. Check your coals, pebbles and logs against the packing list. If any are missing or damaged, contact Gazco for replacements. Always ask for genuine Gazco parts.
28
INSTAllATION INSTRUCTIONSINSTAllATION
15.1.9 Depending on the fuel effect that you have been supplied with, follow the correct section below.
15.2 Coal and Pebble layout (Single burner fires)
Single burner fires have only one air box and one injector, the burner looks like diagram 47.
47
AR0589
15.2.1 The fire beads and pilot shield should already have been installed, see section 15.1 to 15.9.
15.2.2 Start by placing a small coal or pebble on top of the pilot shield, place small coals or pebbles around the edge of the fire. ensure that there are gaps between each coal or pebble. See diagram 48A.
48A
AR0582
15.2.3 Place the square coals in a single layer in the centre of the fire forming a solid mass. Coals should fit together as tightly as possible but not touching any of the small moulded coals or pebbles around the edge. See diagram 48B.
48B
AR0583
15.2.4 Starting at the front, place alternately large and small coals or pebbles around the perimeter of the fire. The coals or pebbles should sit on the first row of small coals or pebbles and rest up against the inner block of square coals. See diagram 48C.
48C
AR0584
15.2.5 Place as many large coals or pebbles that will fit in a single layer on top of the inner block of square coals. ensure that there are gaps between each coal or pebble and that they only touch at single points. Any smaller gap can be filled with a small coal or pebble. See diagram 48D.
48D
AR0589
15.2.6 A few small coals or pebbles can be positioned on top of this layer to complete the effect.
15.3 Coal and Pebble layout (Twin burner fires) Twin burner fires have 2 air boxes and 2 injectors; their
burners look like diagram 49.
49
AR0591
15.3.1 The fire beads and pilot shield should already have been installed, see section 15.1 to 15.9.
29
INSTAllATION INSTRUCTIONSINSTAllATION
15.3.2 Start by placing a small coal or pebble on top of the pilot shield, place small coals or pebbles around the edge of the fire. ensure that there are gaps between each coal or pebble. See diagram 50A.
50A
AR0585
15.3.3 Place pebbles or coals (if coals, use the square coals) in a single layer in the centre of the fire forming a solid mass. Fit together as tightly as possible but not touching the smaller pebbles or coals around the edge. See diagram 50B
50B
AR0586
15.3.4 Starting at the front, place alternately large and small coals or pebbles around the perimeter of the fire. The coals or pebbles should sit on the first row of small coals or pebbles and rest up against the inner block of square coals. See diagram 50C.
50C
AR0587
15.3.5 Place as many large coals or pebbles that will fit in a single layer on top of the inner block of square coals. ensure that there are gaps between each coal or pebble and that they only touch at single points. Bridge the large gaps with the large coals or pebbles, any small gaps left can be filled with a small coal or pebble. See diagram 50D.
50D
AR0588
15.3.6 A few small coals or pebbles can be positioned on top of this layer to complete the effect.
15.4 log or Driftwood layout
15.4.1 Identify the logs or driftwood that you have been supplied with. See diagram 51 and Spares List on page 41.
51
AR0588
Identify which of the illustrated layouts best suits the size of the fire you have and the logs or driftwood you have been sent.
30
INSTAllATION INSTRUCTIONSINSTAllATION
SMAll FIRES
52
AR0575AR0574
AR0578AR0577
15.4.2 Place two logs as shown. See diagram 49A.
15.4.3 Place the log as shown. See diagram 49B.
15.4.4 Place the rest of the lower layer of logs as shown. See diagram 49C.
15.4.5 Place the second layer of cross logs as shown. See diagram 49D.
15.4.6 You may have been supplied some smaller logs or cones which are provided to finish off the layout.
MEDIUM FIRES
53
AR0568 AR0569
AR0567AR0566
15.5.1 Place two logs as shown. See diagram 50A.
15.5.2 Place the logs as shown. See diagram 50B.
15.5.3 Place the rest of the lower layer of logs as shown. See diagram 50C.
15.5.4 Place the second layer of cross logs as shown. See diagram 50D.
15.5.5 You may have been supplied some smaller logs or cones which are provided to finish off the layout.
lARGE FIRES
54
AR0572 AR0573
AR0571AR0570
31
INSTAllATION INSTRUCTIONSINSTALLATION/COMMISSIONING
15.6.1 Place two logs as shown, see diagram 51A.
15.6.2 Place the logs as shown, see diagram 51B.
15.6.3 Place the rest of the lower layer of logs as shown, see diagram 51C.
15.6.4 Place the second layer of cross logs as shown, see diagram 51D.
15.6.5 You may have been supplied some smaller logs or cones which are provided to finish off the layout.
16. COMMISSIONING
15.1 Close all windows and doors to the room, check all controls, and allow fire to burn on maximum for 5 minutes. Test for spillage of flue products using a smoke match. Pass the lighted smoke match along the top front edge just inside the opening or canopy. See diagram 55.
55
AR0573
15.2 If the fire spills, run for a further 10 minutes and re-check. If there is still spillage, disconnect the fire and seek expert advice.
15.3 If there are extractor fans in the room or adjacent rooms, the spillage test must be repeated with the extractors running on maximum.
15.4 For RD VeRSIONS: If spillage is detected and no air vent is fitted in the room, re-check for spillage with a window slightly open. If this cures the spillage, it will be necessary to fit a vent.
IF SPILLAGe PeRSISTS, DISCONNeCT THe APPLIANCe AND SeeK exPeRT ADVICe.
32
SERvICING INSTRUCTIONSSERVICING/FAULTFINDINGCHARTS
1. SERvICING REQUIREMENTS
This appliance must be serviced at least once a year by a competent person.All tests must be serviced by best practice as described by the current Gas Safe recommendations.
1.1 Before any test are undertaken on the appliance, conduct a gas soundness test for the property to ensure that there are no gas leaks prior to starting work.
1.2 Before any tests are undertaken on the appliance it is also recommended to fully check the operation of the appliance.
FAUlT
a) Pilot will not light
b) No spark
c) Pilot will not stay lit or fire goes out in use
d) uneven flame pattern, for example to one side only.
e) Blue flame
f) Low flame height
g) Popping
CAUSE/POSSIbLEREMEDy
See Ignition Functional Check 1 See Ignition Functional Check 2
See Flame Failure Functional Check 1. The coals or logs may need adjusting to even the flame pattern.
1. The fire will burn blue on initial lighting, until the heat generated allows the gas to burn yellow, typically within 20 mins.
2. Insufficient gas pressure, check pressure setting.
3. The aeration plate may be set wrongly.
1. This may be caused by low gas pressure, therefore: Check gas pressure
2. The visual effect of these fires is controlled by the placing of the coals or logs, try slight adjustments.
1. Some popping will always be present - severe popping can be caused by incorrect burner pressure.
2. Not enough clay beads.
3. Try slight adjustments to the coal layout.
1.3 Special checks 1.3.1 Clean any lint or fluff from the pilot - pay particular
attention to the aeration hole in the side of the pilot
1.3.2 Clean away any fluff or lint from under the burner
1.3.3 Check that the spark gap on the pilot is correct
1.4 Correct any faults found during the initial tests and then re-commission the appliance conducting the usual safety checks.
1.5 Advise the customer of any remedial action taken.
33
SERvICING INSTRUCTIONSFAUlT FINDING ChARTS
IGN
ITIO
N F
UN
CTI
ON
Al C
hEC
K 2
NO
SPA
RK
ensu
re th
ere
is no
deb
ris a
roun
d th
e pi
lot a
ssem
bly,
(e
.g. c
oal,
soot
etc
.) w
hich
cou
ld s
hort
the
spar
k, c
lean
the
area
.
Con
sult
the
user
s in
stru
ctio
ns, r
etry
.
Ope
rate
the
valv
e to
lig
ht th
e pi
lot,
does
the
valv
e 'cl
ick'
?
Is th
e ga
p be
twee
n el
ectro
de a
nd th
erm
ocou
ple
as in
dia
gram
13
in
repl
acin
g pa
rts s
ectio
n?
Has
igni
tion
lead
be
com
e de
tach
ed o
r is
conn
ectio
n po
or?
Rem
ove
the
elec
trode
lead
fro
m e
lect
rode
with
insu
late
d
plie
rs. H
old
the
tip 3
.5m
m fr
om th
e
pilo
t pip
ewor
k, is
ther
e a
spar
k
whe
n th
e va
lve
‘clic
ks’?
Is th
e el
ectro
de w
ire
deta
chab
le fr
om th
e pi
ezo
in
the
valv
e?
Repl
ace
the
com
bine
d le
ad
and
piez
o, r
etry
.
Cor
rect
and
ret
ry.
Che
ck fo
r de
fect
ive
or
dam
aged
con
trol k
nob
spin
dle
or
cam
ope
ratio
n. C
heck
for
co
rrec
t loc
atio
n of
pie
zo
com
pone
nts.
Cor
rect
and
ret
ry.
Rem
ove
the
elec
trode
lead
from
th
e pi
ezo.
Ope
rate
the
valv
e.
Doe
s a
spar
k ju
mp
from
the
piez
o to
the
valv
e bo
dy?
Is th
e va
lve
bein
g
oper
ated
cor
rect
ly?
Rese
t the
ele
ctro
de g
ap, r
etry
.
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
No N
o
Repl
ace
the
OD
S un
it.Re
plac
e th
e pi
ezon
an
d re
tryRe
plac
e th
e el
ectro
de
lead
and
ret
ry.
Yes
No
IGN
ITIO
N F
UN
CTI
ON
Al C
hEC
K 1
PILO
T W
ILL
NO
T LI
GH
T
ensu
re th
ere
is no
deb
ris a
roun
d th
e pi
lot a
ssem
bly,
(e.g
. soo
t, et
c.)
whi
ch c
ould
sho
rt th
e sp
ark,
cle
an th
e ar
ea. C
heck
for
fluff
in th
e pi
lot
aera
tion
hole
. See
dia
gram
13,
arr
ow A
in r
epla
cing
par
ts s
ectio
n
Ope
rate
the
valv
e.Is
ther
e a
spar
k?
Con
sult
use
r
Inst
ruct
ions
and
ret
ry.
ensu
re g
ap b
etw
een
elec
trode
and
ther
moc
oupl
e is
as d
iagr
am 1
3 in
rep
laci
ng
parts
sec
tion
and
retry
. If t
he
gap
is O
K th
en fi
rst c
hang
e th
e ig
nitio
n le
ad a
nd r
etry
, if
still
no
good
then
cha
nge
the
piez
o
Che
ck is
olat
ion
tap
and
gas
met
er, r
etry
.
Cor
rect
and
re
try.
Purg
e th
e ga
s pi
pes
and
retry
.
SEE
NO
SPA
RK C
hAR
TSy
STEM
OK
Ther
e is
a bl
ocka
ge in
the
syst
em, c
heck
the
inle
t tes
t poi
nt,
the
mag
sea
ting
valv
e an
d ga
s fil
ter.
Is th
e ga
s tu
rned
on
to th
e ap
plia
nce?
Is th
e ga
s pr
essu
re c
orre
ct?
Has
the
syst
em g
ot
any
air
in it
?
Doe
s th
e pi
lot l
ight
?
Is th
e co
ntro
l bei
ng
oper
ated
cor
rect
ly?
Will
the
pilo
t lig
ht
with
a m
atch
?
No
Yes
No
Yes
No
Yes
Yes
No
NoYe
s
No No
Yes
Yes
No
34
SERvICING INSTRUCTIONSFAUlT FINDING ChARTS
PILO
T W
ILL
NO
T ST
AY L
IT O
R FI
Re G
OeS
Ou
T IN
uSe
ensu
re th
ere
is no
deb
ris a
roun
d th
e pi
lot a
ssem
bly,
(e
.g. c
oal,
soot
etc
.) C
heck
for
fluff
in th
e pi
lot a
erat
ion
hole
. Se
e di
agra
m 1
3 ar
row
A in
rep
laci
ng p
arts
sec
tion.
If th
e ap
plia
nce
goes
out
in u
se c
ontin
ually
, thi
s m
ay m
ean
that
the
oxyg
en
depl
etio
n se
nsor
has
bee
n ac
tivat
ed. T
he a
pplia
nce
shou
ld n
ot b
e us
ed u
ntil
the
caus
e ha
s be
en fo
und
and
rect
ified
.
Prob
lem
is w
ith th
e pi
pew
ork
or
fittin
gs w
hich
lead
to
the
fire.
Cor
rect
an
d re
try.
Is th
erm
ocou
ple
conn
ectio
n go
od
in b
ack
of v
alve
?
Repl
ace
OD
S un
it.
Will
pilo
t st
ay a
light
?
Cha
nge
mag
un
it.
Is th
e pi
lot f
lam
e of
the
corr
ect l
engt
h? S
ee
diag
ram
13
in r
epla
cing
pa
rts s
ectio
n.
Cha
nge
the
OD
S un
it.
Will
pilo
t st
ay a
light
?W
ith th
e pi
lot
runn
ing
is th
e ga
s pr
essu
re a
s st
ated
on
the
data
badg
e?
With
the
fire
runn
ing
on fu
ll is
the
gas
at
the
pres
sure
sta
ted
on
the
data
badg
e?
Run
for
3 m
ins,
tu
rn o
ff, ti
me
inte
rval
un
til m
ag u
nit s
huts
w
ith a
clic
k. Is
this
grea
ter
than
7
seco
nds?
Run
for
3 m
ins,
turn
of
f, tim
e in
terv
al u
ntil
mag
uni
t shu
ts w
ith a
cl
ick.
Is th
is gr
eate
r th
an 7
sec
onds
?
Tigh
ten
the
co
nnec
tion
and
retry
.
No
No
No
No
No
No
Yes
SyST
EM O
K
Yes
Yes
Yes
Yes
No
Yes
Yes
NoLigh
t the
pilo
t and
kee
p th
e co
ntro
l kno
b pu
shed
in
at le
ast 1
0 se
cond
s be
fore
letti
ng g
o.
FlAM
E FA
IlU
RE F
UN
CTI
ON
Al C
hEC
K 3
Yes
35
1.5 undo the gas feed connection to the injector or ‘T’ piece as appropriate, see diagram 3D or 4C.
3
AR0549
4
AR0555
1.6 undo the screws holding the fire to the hearth as appropriate. See diagram 5.
5
AR0542AR0622
1.7 Lift the fire away from the controls and tip the fire beads into a container for later replacement.
1.8 All parts are now accessible for servicing. NOTE: if the controls are mounted away from the fire, then
only step 16.3 is necessary to gain access to most items requiring servicing.
1. FIRE REMOvAl
1.1 Turn the gas supply off at the isolation device.
1.2 Carefully remove all the ceramic fuel pieces and store for later replacement.
1.3 Pull off the control knob (Seagas valve only) and remove the fascia panel by removing the two securing screws. See diagram 1.
1
AR0597 AR0598
AR0623
1.4 undo the two screws holding the pilot in place. See diagram 2.
2
AR0548
SERvICING INSTRUCTIONSREPlACING PARTS
36
2. IGNITION lEAD & PIEzO
2.1 Control Type C - Mertik Maxitrol valve Only
If a new piezois required it will be necessary to change the gas valve. Refer to section 8.
2.1 Control Type B - Babysit valve Only
2.1.1 It is not necessary to remove the fire.
2.1.2 Remove the fascia panel by removing the two screws. See diagram 6.
6
AR0597 AR0598
AR0623
2.1.3 The piezo is removed by undoing the plastic nut securing it to the fascia panel.
2.1.4 Pull the ignition lead off the piezo and the electrode, remove it from its vidaflex insulation.
2.1.5 When replacing the ignition lead, ensure that the insulation is replaced leaving a gap before it reaches the electrode. Secure the lead with tie wrap fasteners.
2.1.6 Check the operation of the replaced piezo and ignition lead. Check the spark gap. See diagram 7.
SERvICING INSTRUCTIONSREPlACING PARTS
7
AR0097
2.2 Control Type A - Seagas valve Only
2.2.1 Remove the fire, see section 15 (unless the controls are mounted away from the fire).
2.2.2 undo the lock ring securing the valve to the control tray. Remove the valve assembly. See diagram 8A.
8
AR0562
2.2.3 undo the two screws securing the piezo to the control valve, see diagram 8B.
2.2.4 Holding the two halves of the control valve together (it is spring loaded), pull the piezo body off the control valve. Immediately replace with a new piezo and replace the two screws securing it to the valve. Replace valve assembly.
2.2.5 Check the operation of the new piezo and lead with the pilot running.
ensure the two halves of the control are secured correctly and leak tested after completion.
37
3. ODS PIlOT UNIT
3.1 Remove the fire, see section 15.
NOTE: IT IS NOT NeCeSSARY TO ReMOVe THe FIRe IF THe CONTROLS ARe MOuNTeD AWAY FROM THe FIRe.
3.2 Gently pull the ignition lead off the electrode. See diagram 9, arrow A.
9
A
3.3 undo the thermocouple connection at the rear of the gas valve. See diagram 10A or 11B.
10
AR0557
A
A
AR0556
11
AR1114
B
3.4 undo the pilot pipe connection and replace pilot.
3.5 After re-assembly, set the spark gap, see diagram 9. Check for gas sound and carry out a flame failure functional check detailed in the flowchart, especially the mag drop out time.
4. MAG UNIT
4.1 Control Types A & B - Babysit valve & Seagas valve
4.1.1 Remove the fire, see section 1.
NOTe: it is not necessary to remove the fire if the controls are mounted away from the fire.
4.1.2 undo the mag unit retaining nut at the back of the control valve. See diagram 12C or 13A.
12
AR0562
SERvICING INSTRUCTIONSREPlACING PARTS
38
13
AR0563
4.1.3 After removing the retaining nut, the mag unit can be tapped out and a replacement fitted.
4.1.4 Replace the mag unit retaining nut and tighten. Note: This is a gas-tight seal.
4.1.5 After re-assembly, carry out the flame failure functional check detailed in the flowchart, especially the mag drop out time.
4.2 Control Type C - Mertik Maxitrol valve Only
4.2.1 Remove the thermocouple from the back of the control valve. See diagram 14 arrow B.
14
AR1114
B
C
4.2.2 undo the mag unit retaining nut. See diagram 14, arrow C.
4.2.3 After removing the retaining nut, the mag unit can be tapped out and a replacement fitted.
4.2.4 Replace the mag unit retaining nut and tighten. Note - this is a gas tight seal.
4.2.5 Replace thermocouple and check for gas leaks.
4.2.6 After reassembly, carry out the flame failure functional check, detailed in the flow chart following, particularly the mag unit drop out time.
5. MAIN INJECTORS
5.1 Remove the fire. See section 1.
5.2 With the fire removed, where appropriate undo the injector compression nut(s).
5.3 Rotate the injector until it is fully removed.
5.4 Replace with the correct replacement injector. When ordering always state the model, gas type and serial number.
5.5 After re-assembly, check for gas leaks.
6. PRIMARy AERATION PlATE
6.1 Locate the aeration plate on the underside of the airbox and remove the nut, see diagram 15.
15
AR0564
6.2 When replacing the aeration plate, ensure that the hole in the aeration plate is correctly aligned to one of the holes in the underside of the airbox, replace the nut.
NOTe: eNSuRe THe CORReCT SIZe AeRATION HOLe IS ALIGNeD WITH ONe OF THe HOLeS IN THe AeRATION BOx - See TeCHNICAL SPeCIFICATION. LPG APPLIANCeS DO NOT ReQuIRe A PRIMARY AeRATION PLATe
SERvICING INSTRUCTIONSREPlACING PARTS
39
7. GAS vAlvE
7.1 Control Type C - Mertik Maxitrol valve Only
7.2 Disconnect the 2x8mm and 1x4mm gas pipe fittings at the back of the gas valve, arrow A and disconnect the thermocouple. See diagram 16 arrow B.
16
AR1114
B
A
7.3 undo the single screw that secures the left-hand side of the control cover. See diagram 17.
17
AR0915
7.4 To release the right-hand side of the control cover, insert a narrow blade screwdriver into the slot shown in diagram 18, lever it gently and pull from the right-hand side at the same time. The cover will now come off. There is a small cylindrical metal spacer inside the cover, this must be kept and replaced on the fixing screw during re-assembly.
18
AR0916
7.5 Disconnect the ignition lead from the gas valve, see section 28.
7.6 undo the two screws securing the gas valve to the control bracket and remove the valve.
7.8 Replace in reverse order.
7.9 Check all joints for gas leaks; check operation of the thermocouple and ignition lead.
8. ChANGING BETWEEN GAS TyPES
8.1 The following parts must be changed or altered when converting from one gas type to another:
8.2 Fires with Control type A & B Seagas and Babysit Valves •Maininjector •Aerationplate •PilotAssembly •Databadge •BurnersettingpressureHIGH* •BurnersettingpressureLOW*
8.3 Fires with Control type C - Mertik Maxitrol uC Valves •EngineAssembly •AirBoxGasket •PilotAssembly •BurnerSettingPressureHighandLowarepreseton Mertik Valves
* Burner Setting pressure to be set on site by fitter. Refer to Technical Specification on page 11 & 12.
SERvICING INSTRUCTIONSREPlACING PARTS
40
SERvICING INSTRUCTIONSREPlACING PARTS
9. ShORT SPARES lIST
BABySIT vAlvE
Valve GC0069 Piezo GC0051 Ignition lead (0.5m) GC0013 Ignition lead (1.5m) PI0029
SEAGAS vAlvE Valve GC0074 Piezo & lead GC0062 Ignition lead extension (1.5m) GC0078 Mag unit GC0016 Knob GC0058
MERTIK MAxITROl vAlvE Valve GC0096 (preset for fire) Ignition lead GC0090 Mag unit GC0092 upgrade kit 8455 Pilot shield GZ1368 Control cover GC0087
NATURAl GAS PARTS 800 Injector IN0011 1100 Injector IN0013 1600 Injector IN0010 Pilot (0.5m thermocouple) PI0047 Pilot (1.5m thermocouple) PI0049 Aeration Plate Me0833
lPG PARTS 400 Injector IN0007 600 Injector IN0026 Pilot (0.5m thermocouple) PI0048 Pilot (1.5m thermocouple) PI0050
MISCEllANEOUS PARTS Pilot shield GZ1368 Clay beads (small) 1 litre Ce0240 Clay beads (large) 1 litre Ce0241 Beads (small) 0.5 litre Ce0239 Beads (large) 2 litre Ce0242 Small moulded coals. Bag of 9 Ce0216 Large moulded coals. Bag of 6 Ce0217 Small moulded coals. Bag of 14 Ce0235 Large moulded coals. Bag of 9 Ce0236 Square coals (Black) Ce0007 A1 burnt log. 240x110x70mm Ce0220 A2 burnt log 240x110x60mm Ce0221 B1 burnt log 150x120x65mm Ce0222 B2 burnt log 150x70x60mm Ce0223 1 log 300x100x90mm Ce0224* 4 log 420x70x35mm Ce0225* 5 log 320x60x40mm Ce0226* 6 log 270x60x45mm Ce0227* 7 log 200x40x25mm Ce0228* 8 log 190x35x40mm Ce0229* 9 log 160x40x30mm Ce0230* 11 log 130x40x20mm Ce0231* 12 log 150x25x20mm Ce0232* 13 log 95x35mm Ce0233* 14 pine cone 95x50mm Ce0234* Small pebbles. Bag of 9 Ce0456 Small pebbles. Bag of 14 Ce0457 Medium pebbles. Bag of 9 Ce0458 Medium pebbles. Bag of 14 Ce0459 Square coals (White) Ce0460
19
AR0565
* If driftwood effect add DW after log code
41
MODElS
FIRE TyPE DESCRIPTION BURNER FUEl TyPE AS SPECIFIED8041 Regency hob B1 Coals8062 Combination C1 Coals8064 Arched insert C1 Coals8000 Tiled insert C1 Coals8002 Horseshoe inserts C1 Coals8004 Adelaide C1 Coals 8102 Art Nouveau C1 Coals8063 London Arch C1RD Coals 8202 Art Nouveau milner D1 Coals8026 16” Taper D1 Coals8210 Victorian milner D2 Coals8027 18” Taper e2 Coals8021 Small Cromwell e2 Coals8118 15” Baskets O.D. C3 Coals8123 14” Rochford A3 Coals8124 16” Basket O.D. D3 Coals8125 18” Basket O.D. F3 Coals8126 20” Basket O.D. G2 Coals 8200 16” T back D3 Coals8022 Large Cromwell F3 Coals8106 Adam-Plymouth-Pub Scene C4 Coals8129 Small Spanish C4 Coals8130 Large Spanish e4 Coals8018 18” Swans Nest e5 Coals8019 24” Swans Nest CC6 Logs8020 36” Swans Nest GG8 Logs8329 uK Log Basket G2 Logs
43
SERvICE RECORDS
1ST SERvICE 2ND SERvICEDate of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dealer’s Stamp/Gas Safe Registration Number Dealer’s Stamp/Gas Safe Registration Number
3RD SERvICE 4ThE SERvICEDate of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dealer’s Stamp/Gas Safe Registration Number Dealer’s Stamp/Gas Safe Registration Number
5ThE SERvICE 6ThE SERvICEDate of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dealer’s Stamp/Gas Safe Registration Number Dealer’s Stamp/Gas Safe Registration Number
7ThE SERvICE 8ThE SERvICEDate of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dealer’s Stamp/Gas Safe Registration Number Dealer’s Stamp/Gas Safe Registration Number
9ThE SERvICE 10ThE SERvICEDate of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Next Service due: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dealer’s Stamp/Gas Safe Registration Number Dealer’s Stamp/Gas Safe Registration Number
Gazco limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England Ex2 7JGTel: (01392) 261999 Fax: (01392) 444148 E-mail: [email protected]
A member of the Stovax Group