MRC FPV Camera Plane
-
Upload
van-hauten -
Category
Documents
-
view
230 -
download
0
Transcript of MRC FPV Camera Plane
-
8/12/2019 MRC FPV Camera Plane
1/16
5inches
Printsc
ale
**P
RINTTHISPAGEFIR
ST**tocheck
tha
ttheprintedscale
iscorrect.The
blacklineaboveshouldbefive
incheslong.
Ifitmeas
uresto5inches
the
nprinttherestoft
hepages.
PDF
NOTES
andTIP
S
MikeysRCFPVC
ameraPl
ane
Trim
paperuptotheredlines.
After
trim
mingedgesplace
edgesofpaper
together,usetheredli
nestohelp
alig
ntheplansthenta
petogether.
Thisplanewasdesignedtobea
capableofbasic
acrobaticma
nuvers(rollsandlo
ops)whilecarrying
acamerasoFPVpilotscouldha
vearesponsivepla
ne
thatwasfun
toflywithanFPV(
FirstPersonView)camera
setup.
Itwas
alsodesignedsothatnodissasembly
was
neededtofit
itinthecar,saving
timeandcomplication
whenseting
upattheflyingsite.
Itscapableofcarrying
about1poundofcameraequip
mentaloft
.
-
8/12/2019 MRC FPV Camera Plane
2/16
This plane is designed to carry a camera mounted far
forward on the nose. If you dont intend to carry a camera make
sure to find a good battery location that will still allow the plane to balance on the CG.
3D side view of Mikeys RC FPV Camera Plane
Wings have about 3-4 degrees of
dihedral for added stability.
Popcicle sticks glued here to
support the battery tray.
12 inch BBQ skewers glued here to support the wings.
Then cover with packing tape for smooth air flow.
Suggested camera location.
Extra foam / fuselage material here is meant to act as a
bumper to protect the camera equipment in a crash.
-
8/12/2019 MRC FPV Camera Plane
3/16
Angled back view of Mikeys RC FPV Camera Plane
11 inch BBQ skewers glued to fuselage and wing
to support wings. Its best to drill holes in the wings
and fuselage to make a really strong joint.
Popcicle sticks glued on the bottom to protect the bottom of
the fuselage during landings.
3 motor mount pieces glued here to support the
motor. Then glue popcicle sticks to the rear facing
motor mount piece so that the motor mount screws
have something to grab into.
Tail boom supports get glued on here.
-
8/12/2019 MRC FPV Camera Plane
4/16
Tail
.Plane Requirements*11.1V 1600 -2200mAh 20C Li-po.
*1000 KV brushless motor with flat mount.
*30 amp speed control.
*10 X 6 GWS style prop.*3, 9 gram servos.
Build Materials*3/16th or 1/4 inch Foam core for the fuselage, wings and tail. You can
use 6 mm Depron also but you will have to add extra support
to it to make it more ridgid. About40 X 24 inches of board is needed.*About 15 popsicle sticks.
*1/16 Drill Rod (from a hardware store) or RC pushrods,
about 28 inches are needed. OR ypu can use RC pushrods if you
have them.
*Hot glue(prefered) or 5 min epoxy.
*Thick packing tape for control surface hinges.
*About 8, 12 inch wooden BBQ skewers.
-
8/12/2019 MRC FPV Camera Plane
5/16
-
8/12/2019 MRC FPV Camera Plane
6/16
Cut this piece out and use it as the battery tray.
www.MikeysRC.com
COPYRIGHT 2010 MikeysRC
-
8/12/2019 MRC FPV Camera Plane
7/16
This is a suggested mounting
location for the AUX battery
for your FPV equipment. Cut
out and use it as a battery tray.
Aileron - Elevator
popsicle stick control horn
templates.
DoNOTRedistribute
-
8/12/2019 MRC FPV Camera Plane
8/16
Topnosep
iece.
COPYRIGHT2010MikeysR
C
Sete
levatordeflectiontoabout1/2inchu
p
and1/2inchdownmea
suredattheback
ofth
eelevator.
-
8/12/2019 MRC FPV Camera Plane
9/16
Cut out this hole for the elevator tab
to slide into.
Glue a 12 inch BBQ skewer here on one boom to stiffin the tail.
Glue a 12 inch BBQ skewer here to stiffin the wing.
Then cover with packing tape for smoother airflow.
-
8/12/2019 MRC FPV Camera Plane
10/16
Center of gravity is on this line.
Thisha
shed
lineare
agoe
s
underthe
wing.
This area sticks out behind the wing.
COPYRIGHT 2010 MikeysRC
-
8/12/2019 MRC FPV Camera Plane
11/16
The plane should balance when heldhere.
Tail boom supports.
These get glued onthe back of the wing,
and on top of the boom.
DoNOTRedistribute
-
8/12/2019 MRC FPV Camera Plane
12/16
Glue a 12 inch BBQ skewer here to stiffin the wing.
Then cover with packing tape for smoother airflow.
-
8/12/2019 MRC FPV Camera Plane
13/16
www.MikeysRC.com
Set aileron deflection to about 1/2 inch up
and 1/2 inch down measured at the back
of the aileron.
-
8/12/2019 MRC FPV Camera Plane
14/16
Glue the booms under the wingwhere these lines are.
-
8/12/2019 MRC FPV Camera Plane
15/16
-
8/12/2019 MRC FPV Camera Plane
16/16
Thanks for trying my plans!I hope you have fun with them!
Please tell your friends about us!
Remember you can buy ALL theelectronics for this plane at,
WWW . MIKEYSRC . COM
Set aileron deflection to about 1/2 inch up
and 1/2 inch down measured at the back
of the aileron.