MPR Receiver Quick Start Guide vr1.5 MPR Receiver – Overview

TeleDelta is proudly an Australian owned company. s:\teledelta\mpr series\mpr receiver quick start guide vr1.5.docx

www.teledelta.com

Page 1 of 17

Quick Start Operation and Installation Guide

MPR Series Multi-Purpose Receiver

MPR Receiver Quick Start Guide vr1.5 MPR Receiver – Overview

TeleDelta is proudly an Australian owned company. s:\teledelta\mpr series\mpr receiver quick start guide vr1.5.docx

www.teledelta.com

Page 2 of 17

Contents Revision .................................................................................................................................................. 2

Quick Start - Getting Started Guide ........................................................................................................ 3

Navigation Keys Operation Instruction ................................................................................................ 4

Confirm or Change the Default IP Address ......................................................................................... 4

Configuration through WEB Management .............................................................................................. 5

First Time Log On ................................................................................................................................ 5

Main Interface Introduction .................................................................................................................. 6

Appendix 1 - Setup Example Audio Only Service (TSIMA) .................................................................... 7

Setting the Receiver RF ................................................................................................................... 7

Status page ...................................................................................................................................... 8

Check the CA / CAM settings .......................................................................................................... 9

Select Program Decryption ............................................................................................................ 10

Select Program .............................................................................................................................. 11

Appendix 2 - Setup Example VAST TV service (ABC24) ..................................................................... 12

Setting the Receiver RF (single tuner models) .............................................................................. 12

Status page .................................................................................................................................... 13

Check the CA / CAM settings ........................................................................................................ 14

Select Program Decryption, ........................................................................................................... 15

Select Program .............................................................................................................................. 16

Revision

File MPR Receiver Quick Start Guide Vr1.5.Docx

MPR Receiver Quick Start Guide vr1.5 MPR Receiver – Overview

mpr receiver quick start guide vr1.5.docx Page 3 of 17

Quick Start - Getting Started Guide

Switch on the equipment through the back power switch, the unit is powered up and start the initialization. After power on the LCD screen is lights up, and displays information as follows

The initialization takes about 30 seconds to complete. The input/output indicator LEDs turn red after the first successful initialization because the signal is not locked. After configuration of the device, the corresponding LEDs will show the correct status.

MPR Receiver Quick Start Guide vr1.5 MPR Receiver – Overview

mpr receiver quick start guide vr1.5.docx Page 4 of 17

Navigation Keys Operation Instruction Use the 6 navigation keys on front panel: Up / Down / Left / Right / Menu / Ok to enter the configuration menu. Enter “Menu”:

Press “OK” button to enter main menu. Exit Menu/Back for parent Menu

Upon completion of configuration settings, press “OK” button until you go back to the Parent Menu.

Enter Sub-Menu

Press OK button to enter main menu.

Select a sub-menu by pressing UP and DOWN button.

Press MENU button on the selected sub-menu. To change a parameter

Step 1: Enter main menu by pressing OK button.

Step 2: Scroll sub-menu by pressing UP and DOWN button, and press MENU button to change the selected sub-menu.

Step 3: To change parameter settings, press RIGHT and LEFT button to move the cursor in which change must be made.

Press UP button and DOWN to input / select an appropriate setting, then press MENU button to save.

Confirm or Change the Default IP Address Note DHCP is not provided (despite the menu selection)

1. check out the IP on the LCD screen. 2. use the button on the front panel to change the IP, gateway and subnet mask The gateway

should be the same as the management PC’s. The subnet mask should be the same as the management PC’s s. The IP and the server’s IP should be in the same subnet section.

3. reboot the device to take effect. 4. ping the new IP to check whether the device can connect to the management PC.

MPR Receiver Quick Start Guide vr1.5 MPR Receiver – Overview

mpr receiver quick start guide vr1.5.docx Page 5 of 17

Configuration through WEB Management

First Time Log On Configuration is best performed via a web browser. Start a browser and browse to the set ip address of the unit. The log on page will appear

The default User Name and Password are “admin”. If you are unable to connect check for possible reasons for unsuccessful log on:

IP address/ network mask/gateway don’t match with the management PC’s

User name/password is wrong – check the caps lock - lower case is required.

The device is connected to the wrong interface

MPR Receiver Quick Start Guide vr1.5 MPR Receiver – Overview

mpr receiver quick start guide vr1.5.docx Page 6 of 17

Main Interface Introduction After successful log on, the following screen will display:

The main interface can be divided into two areas. 1. Menu: each screen shares same 6 tabs including “Status”, “Inputs”, “Outputs”, “CA”, “System”

and “Reset”. 2. Settings: Configuration data for each function

Menu 1

Settings 2

MPR Receiver Quick Start Guide vr1.5 Appendix 1: Setup Example – Audio Only Service - TSIMA

mpr receiver quick start guide vr1.5.docx Page 7 of 17

Appendix 1 - Setup Example Audio Only Service (TSIMA) Let’s assume that you have a dish and LNB connected and pointed correctly and you are going after the Optus VAST TSIMA service

Setting the Receiver RF

“Zoomed In” version for TSIMA as At Oct 2013

Note: Adjust your LNB L.O. Frequency to suit (if required)

Select

Optus C1/D3 156E, use

13V for standard Vertical

MPR Receiver Quick Start Guide vr1.5 Appendix 1: Setup Example – Audio Only Service - TSIMA

mpr receiver quick start guide vr1.5.docx Page 8 of 17

Status page If all these settings are correct the receiver will lock and the Status page will look similar to this: - Check for a lock

If you have a green lock as shown here and on the front panel then continue the setup

Note – Green for locked

signal

MPR Receiver Quick Start Guide vr1.5 Appendix 1: Setup Example – Audio Only Service - TSIMA

mpr receiver quick start guide vr1.5.docx Page 9 of 17

Check the CA / CAM settings

They should suit the speed of the CAM card you are using:

Now check the CA settings

MPR Receiver Quick Start Guide vr1.5 Appendix 1: Setup Example – Audio Only Service - TSIMA

mpr receiver quick start guide vr1.5.docx Page 10 of 17

Select Program Decryption All the programs are shown and from here you can route them to the CA/CI/CAM slot for the channels that you want to de-scramble

Note: - Only have one service routed to the CI Slot if you have a single service card

Now check / set the CA settings

Select

MPR Receiver Quick Start Guide vr1.5 Appendix 1: Setup Example – Audio Only Service - TSIMA

mpr receiver quick start guide vr1.5.docx Page 11 of 17

Select Program Now select Program Setup for the program that you want

Change the Video Settings from AUTOMATIC as shown below:

Select

Select

Select video

settings as shown

MPR Receiver Quick Start Guide vr1.5 Appendix 2: Setup Example VAST TV service (ABC24)

mpr receiver quick start guide vr1.5.docx Page 12 of 17

Appendix 2 - Setup Example VAST TV service (ABC24) Let’s assume that you have a dish and LNB connected and pointed correctly and you are going after the Optus VAST service

Setting the Receiver RF (single tuner models)

Select

Optus C1/D3 156E, use

13V for standard Vertical

MPR Receiver Quick Start Guide vr1.5 Appendix 2: Setup Example VAST TV service (ABC24)

mpr receiver quick start guide vr1.5.docx Page 13 of 17

Status page

If all these settings are correct the receiver will lock and the Status page will look similar to this: - Check for a lock

If you have a green lock as shown here and on the front panel then continue the setup

Note – Green for locked

signal

MPR Receiver Quick Start Guide vr1.5 Appendix 2: Setup Example VAST TV service (ABC24)

mpr receiver quick start guide vr1.5.docx Page 14 of 17

Check the CA / CAM settings

They should suit the speed of the CAM card you are using:

Now check the CA settings

MPR Receiver Quick Start Guide vr1.5 Appendix 2: Setup Example VAST TV service (ABC24)

mpr receiver quick start guide vr1.5.docx Page 15 of 17

Select Program Decryption,

All the received programs are shown and from here you can route them to the CA/CI/CAM slot for the channels that you want to de-scramble

Now check the CA settings

Select

Note: Check that CAM is not overloaded - only one program is set to decryption if a “Single Service” card is used, or no more than 8 programs for the “Standard” multi service CAM; or no more than 10 programs for the “Super Special” multi

service CAM

MPR Receiver Quick Start Guide vr1.5 Appendix 2: Setup Example VAST TV service (ABC24)

mpr receiver quick start guide vr1.5.docx Page 16 of 17

Select Program

Now select Program Setup for the program that you want

Select

Select

MPR Receiver Quick Start Guide vr1.5 Appendix 3: Trouble Shooting Guide

mpr receiver quick start guide vr1.5.docx Page 17 of 17

Appendix 3: Trouble Shooting Guide:

Problem Check

No program – is CAM card authorised?

Select a known FTA service, (VAST service 10 on 12647MHz for example - valid as at March 2013) If audio and video is present MPR is set up correctly – Have CAM card re-authorised

Receiver locked, CAM okay, but still no program

Check that CAM is not overloaded - only one program is set to decryption if a “Single Service” card is used, or no more than 8 programs for the “Standard” multi service CAM; or no more than 10 programs for the “Super Special” multi service CAM.

Picture but no sound

Establish audio coding type (AAC etc.,) with service provider and check with your dealer to confirm your MPR has this correct codec enabled.

Sound but no Picture (COFDM variant models) with mpeg4 H.264 source encoding

Check that TV receiver is mpeg4 H.264 receive capable. (Not just the USB port…)