Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a...
-
Upload
julius-carroll -
Category
Documents
-
view
223 -
download
5
Transcript of Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a...
![Page 1: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/1.jpg)
Motivation
![Page 2: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/2.jpg)
Project Goals
• Build two PCB boards consists power transmitter and power receiver.
• Add a communication channel between the two boards in order to communicate power management calibration.
• Improving the power delivery efficiency based on the HFSS simulation.
![Page 3: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/3.jpg)
M controller DC 2 DC
AC source at our selected freq
Voltage source
Power AMP תיאום רשת
coil
7 Segment indicator
TX
input
input
![Page 4: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/4.jpg)
coilrectifier
M controllertemperature
transistor
DC 2 DCLoad
RXVoltage -output
![Page 5: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/5.jpg)
Solution AlgorithmThe transistor current and the temperature sensor are the indicators for the M Controller whether to decrease/increase the DC2DC voltage. According to the following logic:
• Temperature goes up, reaching to 70 deg, or the transistor transmits high current.
• M controller decreases the DC2DC voltage Or changes the capacitor
• Temperature goes down, reaching to 60 deg, or the transistor transmits low current.
• M Controller increases the DC2DC voltage Or changes the capacitor
![Page 6: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/6.jpg)
Solution Algorithm
transistor
temperature
M controller DC 2 DC
M controller DC 2 DC
current
תיאום רשת
תיאום רשת
![Page 7: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/7.jpg)
Block Part Comment
Microcontroller Pic 10f 200 / Arduino model Ability to read temperature,IR/BT read/write, ADC
DC2DC TX Input 20V, output 5-20V .I out max 1A
Oscillator K50-HC
Gate Driver IXD1502
Power Amplifier EPC1010
Rectifier Support up to max 50V
DC2DC RX Vin 20V, Vout 5V Max I 3A
Transistor NFET, vds 20V
Temperature sensor 10-90 deg, ability to communicate with the
controller
7 Segment display Displaying the temperature received
![Page 8: Motivation. Project Goals Build two PCB boards consists power transmitter and power receiver. Add a communication channel between the two boards in order.](https://reader036.fdocuments.in/reader036/viewer/2022082505/56649ee05503460f94bf0124/html5/thumbnails/8.jpg)
Project Gantt