MOLCO Texture Recommended Drafts
1
MOLCO Molco Inc. <> Auburn, Maine, USA <> Ph: (+1) 207 514 0399 Molco Lda. <> Oliveira de Azemeis, Portugal <> Ph: (+351) 256 682 099 Texture Drafts Following are listed the most commonly used texture patterns and the recommended “drafts”. These values are for reference only and have been provided by Mold-Tech in Portugal. PATTERN Average depth (Microns) Minimum Suggested Draft PATTERN Average depth (Microns) Minimum Suggested Draft MT 1055/1 8,89 1,5º MT 11000 10 1,5º MT-1055/2 16,00 1,5º MT 11010 25 2º MT-1055/3 18,28 1,5º MT 11020 40 3,5º MT-1055/4 23,62 2º MT 11030 50 4º MT-1055/5 24,64 2º MT 11040 75 6,5º MT-1055 36,83 3,5º MT 11050 110 9º MT-1055/6 45,46 4º MT 11060 75 6,5º MT-1055/7 70,86 5,5º MT 11070 75 6,5º MT-1055/8 78,74 6,5º MT 11080 50 4º MT 11090 90 7,5º MT-11001 4,13 1º MT 11100 150 12,5º MT-11002 8,26 1,5º MT 11110 60 5,5º MT-11003 7,67 1,5º MT 11120 50 4º MT-11004 10,51 1,5º MT 11130 60 5,5º MT-11005 18,77 2º MT 11140 60 5,5º MT-11006 25,00 2º MT 11150 70 5,5º MT-11007 55,43 4º MT 11155 50 8,5º Texture draft requirements may vary depending on the molding material, injection parameters, geometry of the part, mold cooling and other processing factors. The noted values referred above should be verified with the texture supplier during product development. Recommended drafts for other texture patterns may be provided upon request, to do so please contact Molco’s engineering group by phone or through email at [email protected] . March 2011
Transcript of MOLCO Texture Recommended Drafts
MOLCO
Molco Inc. <> Auburn, Maine, USA <> Ph: (+1) 207 514 0399 Molco Lda. <> Oliveira de Azemeis, Portugal <> Ph: (+351) 256 682 099
Texture Drafts
Following are listed the most commonly used texture patterns and the recommended “drafts”. These values are for reference only and have been provided by Mold-Tech in Portugal.
PATTERN Average
depth (Microns)
Minimum Suggested
Draft PATTERN
Average depth
(Microns)
Minimum Suggested
Draft
MT 1055/1 8,89 1,5º MT 11000 10 1,5º
MT-1055/2 16,00 1,5º MT 11010 25 2º
MT-1055/3 18,28 1,5º MT 11020 40 3,5º
MT-1055/4 23,62 2º MT 11030 50 4º
MT-1055/5 24,64 2º MT 11040 75 6,5º
MT-1055 36,83 3,5º MT 11050 110 9º
MT-1055/6 45,46 4º MT 11060 75 6,5º
MT-1055/7 70,86 5,5º MT 11070 75 6,5º
MT-1055/8 78,74 6,5º MT 11080 50 4º
MT 11090 90 7,5º
MT-11001 4,13 1º MT 11100 150 12,5º
MT-11002 8,26 1,5º MT 11110 60 5,5º
MT-11003 7,67 1,5º MT 11120 50 4º
MT-11004 10,51 1,5º MT 11130 60 5,5º
MT-11005 18,77 2º MT 11140 60 5,5º
MT-11006 25,00 2º MT 11150 70 5,5º
MT-11007 55,43 4º MT 11155 50 8,5º
Texture draft requirements may vary depending on the molding material, injection parameters, geometry of the part, mold cooling and other processing factors. The noted values referred above should be verified with the texture supplier during product development.
Recommended drafts for other texture patterns may be provided upon request, to do so please contact Molco’s engineering group by phone or through email at [email protected].
March 2011
