Modern Welding Company · Modern Welding Company ... Anhydrous Ammonia Vessels; ... “Any press...
Transcript of Modern Welding Company · Modern Welding Company ... Anhydrous Ammonia Vessels; ... “Any press...
Modern Welding Company Liquefied Petroleum Gas Division
Bulk Propane and NH3 Vessels, Systems and Installa on Assistance Coast to Coast Availability, American Built By American Cra smen
Call: 888‐800‐8265 or Email us at [email protected]
Modern’s LPG Division will review your energy needs and develop a system to meet your requirements. Our team can provide installa on assistance, if needed, upon delivery of your system.
From alternate emergency propane storage tanks or systems to primary LPG for power genera on or dispensing propane to power your vehicular fleet…we have the knowledge and experience to help. All work is done per NFPA 58 requirements.
Our three (3) ASME manufacturing loca ons are supported by an addi onal five (5) ASME cer fied fabrica on facili es should your requirements call for cri cally short delivery mes.
Three division loca ons are strategically located across the United States:
Fresno, CA
Owensboro, KY
Augusta, GA Each loca on is an ASME Code registered manufacturer with “U” and “R” stamp cer fica ons.
3—30,000 gallon UST LPG Vessels Pump and Hose Assembly
30,000 Gallon Remote Bobtail Filling System
Trailer Mounted 18,000 Gallon “Port‐A‐ Pack” Filling System
Pump and Distribu on Assembly
30,000 Gallon Skid Mounted Filling System
Propane
Green Energy
for our Future
Coast to Coast Manufacturing Capabili es
Modern Welding Company Liquefied Petroleum Gas Division
Bulk Propane and NH3 Vessels, Systems and Installa on Assistance Coast to Coast Availability, American Built By American Cra smen
Call: 888‐800‐8265 or Email us at [email protected]
Other Products:
New ASME Sec on VIII, Div. 1 Code Constructed and Stamped
Aqueous Ammonia Vessels; 50 PSI Design Vessels are key equipment used for emission control systems.
Anhydrous Ammonia Vessels; 250 PSI Design; Post Weld Heat Treated An efficient and widely used source of nitrogen fer lizer Anhydrous Ammonia vessels are manufactured in accordance with the ASME Sec on VIII, Division 1 of the Pressure Vessel Code, “Rules for Construc on of Pressure Vessels. (Also as defined in OSHA 1910.111(a)(2)(iii).
Compressed Gas Associa on Standard, CGA G‐2.1 ‐2014, Standards for the Storage and Handling of Anhydrous Ammonia and Ammonia Solu ons, Sec on 5.1.1.1 states: “Any pressure vessel used as a storage tank (for Anhydrous Am‐monia) shall have been registered with the Na onal Board.”
UN Portable Tanks; Propane or Butane Compa ble, Frames and tanks are ASME, D.O.T., ABS, IMDG and CSC standard codes. Fork li pockets and corner cas ngs allows for stacking of units. 1,100 gallon sizes.
Corporate Office
800‐922‐1932
Newark, Ohio [email protected]
740‐344‐9425
Houston, TX [email protected]
713‐675‐4211
Fresno, CA [email protected]
559‐275‐9353
Rhome, TX [email protected]
817‐636‐2215
Augusta, GA
706‐722‐3411
Orlando, FL [email protected]
407‐843‐1270
Burlington, IA [email protected]
319‐754‐6577
Owensboro, KY [email protected]
270‐683‐5323
Modern Custom Fabrica on Fresno, CA
559‐264‐4741
Modern Welding Company, a na onwide metal fabricator offering regional service and delivery.
Other Modern Welding Company Subsidiaries
ISO Tanks; 6,500 gallon capacity, Coast Guard Approved for waterway shipments.
Carbon and stainless steel construc ons. Variety of applica ons.
30,000 Gallon Saddle Supported Bulk System
Propane
Green Energy
for our Future
= LPG Division Loca ons
“ModernWelding’sLPGDivisionisassociatingwithCalhounTank&Services.WeareproudtowelcomeGaryRaymond’sassistancetotheModernteam.”