power.cummins.com ©2017 Cummins Inc. | D-6279-EN (10/17)

Generator set data sheet

Model: C44 D5e (B3.3)

Frequency: 50 Hz

Fuel type: Diesel

Spec sheet: S-6282-EN

Noise data sheet (open): MSP-3025

Airflow data sheet: MCP-2021

Fuel consumption

Standby Prime

kVA (kW) kVA (kW)

Ratings 44 (35) 40 (32)

Load 1/4 1/2 3/4 Full 1/4 1/2 3/4 Full

US gph 1.1 1.5 2.3 2.7 1.0 1.4 2.2 2.7

L/hr 4.0 5.7 8.8 10.4 3.9 5.4 8.4 10.2

Engine Standby rating Prime rating

Engine manufacturer Cummins

Engine model 4BTAA3.3-G14

Configuration In-line; 4 cylinder diesel

Aspiration Turbocharged and after-cooled

Gross engine power output, kWm 62.6 58

BMEP at set rated load, kPa 1538 1428

Bore, mm 95

Stroke, mm 115

Rated speed, rpm 1500

Piston speed, m/s 5.75

Compression ratio 19:1

Lube oil capacity, L 8

Overspeed limit, rpm 1650

Regenerative power, kW N/A

Governor type Mechanical as standard

Starting voltage 12 V DC

Fuel flow

Maximum fuel flow, L/hr 45

Maximum fuel inlet restriction, mm Hg (clean filter) 101.6

Maximum fuel inlet temperature, °C 70

power.cummins.com ©2017 Cummins Inc. | D-6279-EN (10/17)

Air Standby rating Prime rating

Combustion air, m3/min 4.92 4.47

Maximum air cleaner restriction, kPa 2.5

Exhaust

Exhaust gas flow at set rated load, m3/min 13.02 11.63

Exhaust gas temperature, °C 497 492

Maximum exhaust back pressure, kPa 10

Standard set-mounted radiator cooling

Ambient design, °C @ 12.7mm H2O 55

Fan load, kWm 2 +/- 1

Coolant capacity (with radiator), L 10.3

Cooling system air flow, m3/sec @ 12.7 mm H2O 1.611

Total heat rejection, Btu/min 1877 1734

Maximum cooling air flow static restriction, mm H2O 25.4

Weights Open Enclosed

Unit dry weight, kg (Standard skid) 922 1236

Unit wet weight, kg (Standard skid) 1010 1414

Unit dry weight, kg (optional skid) 1140 1543

Unit wet weight, kg (optional skid) 1228 1631

Dimensions Length Width Height

Open set dimensions (standard skid) 2050 967 1510

Enclosed set dimensions (standard skid) 2270 975 1920

Open set dimensions (optional skid) 2270 967 1720

Enclosed set dimensions (optional skid) 2270 975 2115

power.cummins.com ©2017 Cummins Inc. | D-6279-EN (10/17)

Genset outline

Open set

Enclosed set

Outlines are for illustrative purposes only. Please refer to the genset outline drawing for an exact representation of this model.

Alternator data Connection

1 Temp rise ºC Duty

2 Alternator Voltage

Wye, 3-phase 163/125 S/P UCI22 4C 380-415

Wye, 3-phase 150/105 S/P UCI22 4D 380-415

For more information contact your local Cummins distributor or visit power.cummins.com

©2017 Cummins Inc. All rights reserved. Cummins is a registered trademark of Cummins Inc. PowerCommand, AmpSentry, InPower and “Our energy working for you.” are trademarks of Cummins Inc. Other company, product, or service names may be trademarks or service marks of others. Specifications are subject to change without notice. D-6279-EN (10/17)

Ratings definitions Emergency Standby Power (ESP):

Limited-Time running Power (LTP):

Prime Power (PRP): Base load (Continuous) Power (COP):

Applicable for supplying power to varying electrical load for the duration of power interruption of a reliable utility source. Emergency Standby Power (ESP) is in accordance with ISO 8528. Fuel Stop power in accordance with ISO 3046, AS 2789 and DIN 6271.

Applicable for supplying power to a constant electrical load for limited hours. Limited-Time Running Power (LTP) is in accordance with ISO 8528.

Applicable for supplying power to varying electrical load for unlimited hours. Prime Power (PRP) is in accordance with ISO 8528. Ten percent overload capability is available in accordance with ISO 3046, AS 2789 and DIN 6271.

Applicable for supplying power continuously to a constant electrical load for unlimited hours. Continuous Power (COP) is in accordance with ISO 8528, ISO 3046, AS 2789 and DIN 6271.

Formulas for calculating full load currents:

Three phase output Single phase output

kW x 1000 kW x SinglePhaseFactor x 1000

Voltage x 1.73 x 0.8 Voltage

4 3 2 1

D

C

B

A

3 2 1

D

C

B

A

4

PTC Creo ParametricR R

CKD

FIRST USED ONFOR INTERPRETATIONOF DIMENSIONING ANDTOLERANCING, SEE

APVD

DWNSIM TOUNLESS OTHERWISE SPECIFIED, ALLDIMENSIONS ARE IN MILLIMETERS

17.50-24.99 +0.30/-0.13

10.00-17.49 +0.25/-0.13

5.00- 9.99 +0.20/-0.10

0.00- 4.99 +0.15/-0.08

DIM

HOLE

ANG TOL

DO NOT SCALE PRINT

SCALE

SITE CODE

CUMMINS POWER GENERATION

SIZEDWG

E

DATE

A054J456THIS DOCUMENT (AND THE INFORMATION SHOWN THEREON) ISCONFIDENTIAL AND PROPRIETARY AND SHALL NOT BE DISCLOSED TO OTHERSIN HARD COPY OR ELECTRONIC FORM, REPRODUCED BY ANY MEANS, ORUSED FOR ANY PURPOSE WITHOUT WRITTEN CONSENT OF CUMMINS INC.

R

NOREVREL NO DATEAPVDCKDDWNREVISION

OF

CAD SHEET

1 2

= =96738.1[ ]

= =84333.2[ ]

89735.3[ ]

100640[ ]

483.519[ ]

483.519[ ]

( )

O/AHEIGHT

192076[ ]1818

72[ ]

227690[ ]

103840.9[ ]

DOOR OPENING

2817110.9[ ]

DOOR OPENING

226589[ ]

O/A WIDTH

97538[ ]

76130[ ]

( )512[ ]

1104[ ]

167365.9[ ]

O/A LENGTH 227089[ ]

51620[ ]

143056[ ]

32413[ ]

38515[ ]

1335.2[ ]

DISPLAYCENTER

130051[ ]

DISPLAY CENTER

186974[ ]

110143[ ]

124349[ ]

30212[ ]

65325.7[ ]

1204.7[ ]

151860[ ]

77831[ ]

1265[ ]

A

83332.8[ ]

34314[ ]

173968[ ]

4X 351.4[ ]

813.2[ ]

B

1676.6[ ]

225689[ ]

ECO-168719 C 1 ADD CE TO EXTERNAL REGULATIONS MR PJ A_PATIL 21MAR17

1X �#�

0.8 .X �#�

0.38 .XX�#�

1.0 1/8 B3.3 INT'LASME Y14.5-2009

04FEB15

A_PATIL

P_JARALI

D_ROKADE

OUTLINE,ENCLOSURE

CIL

A045B515

WEIGHT AND C.G DATA (APPROX)

S/NGENSET MODEL

ENGINE MODELALTERNATOR

FRAMEGENSET DRY WEIGHT (KG)

GENSET WET WEIGHT (KG)

CG LOCATION

DIM A DIM B

1

C40,C44C50,C55C60,C66

G14/G12/G13

UC224C 1313 1401 1257 639

2 UC224D 1326 1414 1263 638

3 UC224E 1353 1441 1275 636

4 UC224F 1373 1461 1283 635

5 UC224G 1423 1511 1302 631.5

SERVICE CONNECTION DETAILS FUEL INLET CONNECTION : �n�10 FUEL RETURN CONNECTION : �n�10 WATER INLET CONNECTION : �n�46 WATER OUTLET CONNECTION : �n�33.5 EXHAUST OUTLET CONNECTION: �n�72 AIR INLET CONNECTION : �n�76.5

NOTES: 1 .DIMENSION SHOWN IN [ ] IN INCHES. 2. THE DIMENSIONS AND C.G DATA ARE FOR REFERANCE ONLY 3. ENCLOSURE MOUNTED EYE BOLTS TO BE USED FOR LIFTING GENSET . 4. AIR CLEANER IS MEDIUM DUTY 5. REMOVE SHIPPING BRACKET BEFORE STARTING THE GENSET. 6. VIEWS SHOWS STANDARD SCOPE BASE SKID 7. FUEL TANK CAPACITY 156 LTR APPROX(12 HRS.FUEL AUTONOMY) 8. CUSTOMER LOAD CABLES TO BE FLEXIBLE TO ALLOW MOVEMENTS OF GENSET ON ANTI VIBRATION MOUNTS 9. FOR ALTERNATOR AND ENGINE COMBINATIONS REFER SHEET 2 10. APPLY DRY TORQUE UNLESS AND OTHERWISE SPECIFIED 11. REFER STD OPRATING MANUAL FOR ANY TECHNICAL PROBLEM 12. THIS OUTLINE IS FOR C40,C44,C50,C55,C60,C66 GENSETS

AIR IN

AIR OUT

RADIATOR END

ALTERNATOR END

AIR IN

AIR OUT

AIR IN

AIR OUT

SINGLE POINT LIFT

3D VIEWSCALE 3/32

PART A054L836 IS SUPPLIED IN KIT AND NEED TO INSTALLED AT THE TIME OF GENSET COMMISIONING

POWER CABLE ENTRY

AIR OUT

AIR OUT

CEPGG 1-01-01-116. This item impacts compliance with these External Regulations:

Regulatory Review and Approval is required prior to changing this item per

ECO-168719 Sheet 1 of 3Part Name: A054J456 Revision: C

Drawing Name: A054J457 Revision: C

4 3 2 1

D

C

B

A

3 2 1

D

C

B

A

4

PTC Creo ParametricR R

CKD

FIRST USED ONFOR INTERPRETATIONOF DIMENSIONING ANDTOLERANCING, SEE

APVD

DWNSIM TOUNLESS OTHERWISE SPECIFIED, ALLDIMENSIONS ARE IN MILLIMETERS

17.50-24.99 +0.30/-0.13

10.00-17.49 +0.25/-0.13

5.00- 9.99 +0.20/-0.10

0.00- 4.99 +0.15/-0.08

DIM

HOLE

ANG TOL

DO NOT SCALE PRINT

SCALE

SITE CODE

CUMMINS POWER GENERATION

SIZEDWG

E

DATE

A054J456THIS DOCUMENT (AND THE INFORMATION SHOWN THEREON) ISCONFIDENTIAL AND PROPRIETARY AND SHALL NOT BE DISCLOSED TO OTHERSIN HARD COPY OR ELECTRONIC FORM, REPRODUCED BY ANY MEANS, ORUSED FOR ANY PURPOSE WITHOUT WRITTEN CONSENT OF CUMMINS INC.

R

NOREVREL NO DATEAPVDCKDDWNREVISION

OF

CAD SHEET

2 2

89735[ ]

1429.856[ ]

317.212.5[ ]

38.61.5[ ]

4X 180.7[ ]

753[ ]

753[ ]

753[ ]

753[ ]156.6

6.2[ ]

2359.3[ ]

98138.6[ ]

2359.3[ ]

226989[ ]

38.61.5[ ]

89735.3[ ]

97438[ ]

B3.3 INT'L ALTERNATOR MATRIX

RATING STANDBY PRIME

GENSET MODEL

STANDBYRATING

kVA (kWe)

STANDBYRATING

kWe (kVA)

PRIME RATING

KVA (kWe)

PRIME RATING

kWe (kVA)ENGINE MODEL VOLTAGE WINDING

STD TEMP RISE OPTIONAL TEMP RISE STD TEMP RISE OPTIONAL TEMP RISE

163/27 150/40 125/40 105/40

C44D5 44 (35) - 40 (32) - 4BTAA3.3G14/G13 190 - 416 V 311UCI224C (46.8)

(A053B575)UCI224D (53)(A053B577)

UCI224C (42.5)(A053B575)

UC224D (45)(A053B577)

C55D5 55 (44) - 50 (40) - 4BTAA3.3G14/G13 190 - 416 V 311UCI224D (55)(A053B577)

UCI224E (61)(A053B579)

UCI224D (50)(A053B577)

UC224E (53)(A053B579)

C66D5 66 (53) - 60 (48) - 4BTAA3.3G14/G13 190 - 416 V 311UCI224F (80)(A053B581)

UCI224G (90.8)(A034E089)

UCI224E (60)(A053B579)

UC224F (65)(A053B581)

C40D6 - 40 (50) - 36 (45) 4BTAA3.3G12

190 - 200 V & 380 - 400 V 14UCI224C (60)(A052U904)

UCI224D (65)(A052U911)

UCI224C (55)(A052U904)

UCI224D (56)(A052U911)

208 - 240 V & 416 - 480 V 311UCI224C (55)(A053B575)

UCI224D (62.5)(A053B577)

UCI224C (50)(A053B575)

UCI224D (52.5)(A053B577)

C50D6 - 50 (62.5) - 45 (57) 4BTAA3.3G12

190 - 200 V & 380 - 400 V 14UCI224D (66.3)

(A052U911)UCI224E (73.8)

(A052V396)UCI224D (62.5)

(A052U911)UCI224E (65)(A052V396)

208 - 240 V & 416 - 480 V 311UCI224D (65)(A053B577)

UCI224E (70)(A053B579)

UCI224D (60)(A053B577)

UCI224E (62.5)(A053B579)

C60D6 - 60 (75) - 55 (68) 4BTAA3.3G12

190 - 200 V & 380 - 400 V 14UCI224E (75)(A052V396)

UCI224F (89.4)(A052V401)

UCI224E (70)(A052V396)

UCI224F (75)(A052V401)

208 - 240 V & 416 - 480 V 311UCI224F (91.9)

(A053B581)UCI224G (98.1)

(A054N520)UCI224F (83.8)

(A053B581)UCI224G (87.5)

(A054N520)

ECO-168719 C - --- MR PJ A_PATIL 21MAR17

1X �#�

0.8 .X �#�

0.38 .XX�#�

1.0 5/32 B3.3 INT'LASME Y14.5-2009

04FEB15

A_PATIL

P_JARALI

D_ROKADE

OUTLINE,ENCLOSURE

CIL

A045B515

FOOT PRINT DETAILS

WITH FOOTSWITH OUT FOOTS

3D VIEWSCALE 1/8

3D VIEWSCALE 1/8

16X M12 WELD NUT

CEPGG 1-01-01-116. This item impacts compliance with these External Regulations:

Regulatory Review and Approval is required prior to changing this item per

ECO-168719 Sheet 2 of 3Part Name: A054J456 Revision: C

Drawing Name: A054J457 Revision: C

Part A054J456 C

Part Specifications :A054J456 C

Description Legacy Name External Regulations Application Status Release Phase Code Security Classification Alternates

OUTLINE,ENCLOSURE A054J456 CE Production Only Production Internal use Only

Name Description Legacy Name

A030B356 SPECIFICATION,MATERIAL CES10903

A054J457 DRAWING,ENGINEERING A054J457

CEPGG 1-01-01-116. This item impacts compliance with these External Regulations:

Regulatory Review and Approval is required prior to changing this item per

ECO-168719 Sheet 3 of 3Part Name: A054J456 Revision: C

Drawing Name: A054J457 Revision: C