Milesight CMS Central Management System - use-IP Ltd CMS User Manual.pdf · The Milesight Central...

1 | P a g eFile Format：MS-QR-JS-04 Rev1.0 Durability Date：1 Years

Central Management System

User Manual

Version 1.04

use-IP Ltd

Stamp

https://www.use-ip.co.uk/milesight-cms-central-management-system.html


Copyright Statement

This manual may not be reproduced in any form or by any means to create any derivativesuch as translation, transformation, or adaptation without the prior written permission ofMilesight Technology Co., Ltd(Hereinafter referred to as Milesight).

Milesight reserves the right to change this manual and the specifications without priornotice. The latest specifications and user documentation for all Milesight products areavailable on our official website www.milesight.com.

http://www.milesight.com/


Contents1. Introduction ............................................................................................................................... 4

1.1 Introduction ...................................................................................................................... 41.2 Key Features ...................................................................................................................... 41.3 System Requirements ........................................................................................................ 4

2. Installation ................................................................................................................................. 52.1 Installation Guide .............................................................................................................. 52.2 Login/Logout ..................................................................................................................... 8

2.2.1 Login ....................................................................................................................... 92.2.2 Logout ................................................................................................................... 10

3. Manage .................................................................................................................................... 113.1 Device Management ....................................................................................................... 11

3.1.1 Adding Devices ...................................................................................................... 113.1.2 Removing or Logging Out the Device ..................................................................... 153.1.3 Logout the Added Device....................................................................................... 173.1.4 Editing Device ........................................................................................................ 18

3.2 Device Config .................................................................................................................. 193.2.1 NVR ....................................................................................................................... 193.2.2 Camera .................................................................................................................. 37

3.3 Users ............................................................................................................................... 524. View ......................................................................................................................................... 53

4.1 Live View ......................................................................................................................... 544.1.1 Live view interface ................................................................................................. 554.1.2 Settings of Display the Live View............................................................................ 57

4.2 Playback .......................................................................................................................... 605. Tools ......................................................................................................................................... 62

5.1 E-Map ............................................................................................................................. 625.2 Logs ................................................................................................................................. 63

6. Service ..................................................................................................................................... 646.1 Service ............................................................................................................................ 64


1. Introduction

1.1 Introduction

The Milesight Central Management System(hereinafter referred to as CMS) software worksto give you access and control of your Milesight High Definition Surveillance System. TheMilesight CMS provides multiple operating functionalities, including live view, PTZ control,video playback, motion detection, alarm receiving, log and so on.

This user manual describes the function, configuration and operation steps of CMS. Toensure the proper usage and stability of the CMS, please refer to the contents below andread the manual carefully before operation.

The latest version of the software will be available on our official website. Please check ourofficial website www.milesight.com for upgrading.

1.2 Key Features

² Support NVR as well as camera² Support 1/ 4/ 8/ 9/ 16/ 36/ 64 channels playing synchronously² Full screen for single or multiple channels² Support four monitors² Support modifying video / image parameters of camera² H.265/H.264/MJPEG/MPEG-4 video compression² Support dual-stream² Support multiple PTZ control protocols² Support custom time length for schedule record² Motion detection, alarm recording and image capture function² Easy to install and use² Support back up NVR files from playback² Configuration feature for record/alarm in/alarm out/video loss/motion² Support edit privilege for specific user² CPU/Memory info in the live view

1.3 System Requirements

OS: Windows XP/7/8/10/Vista/Server 2000/Server 2008CPU: 2.4GHZ or fasterMemory: 2G MB or moreGraphic memory: 1G or moreInternet protocol: TCP/IP



2. Installation

2.1 Installation Guide

Run the installation file and install the programs on your computer by following the on-screen instructions. After finishing installation, you will find the programs on the start menuor on the desktop.

Step1: Click the installation file to install;

Figure 2-1-1 Start Setup


Step2: Choose the folder in which to install Milesight CMS;

Figure 2-1-2 Choose File Path

Step3: Choose Start Menu Folder for the Milesight CMS;

Figure 2-1-3 Choose the Start Menu


Step4: Finish the Setup:

Figure 2-1-4 Finish the Setup


2.2 Login/Logout

2.2.1 LoginDouble click the icon to start the software, then choose the user and enter thepassword, the default account Username is: admin; Password is: password. You can checkthe checkbox to remember the password, choose Auto Login to auto login after runningCMS.

Figure 2-2-1 Log In

After logging into the system, you can see the first page is the Live View page as follows:

Figure 2-2-2 Live View


And the meanings of the icons on the top-right are as follows:

Table 2-2-1 Live ViewItem Function Introduction

User name

Click the button to lock the software, and it needs to enter the passwordto unclock

Menu button

Minimize the interface

Restore Down the interface

Maximize the interface

Close the software

To check the hidden pages when the windows is too small to show allthe opened pages

To check the real-time CPU status on PC

To check the real-time RAM memory on PC

Click the Menu button , the interface is as follows:

Language , the live view record，log retention, auto bootup whenWindows starts up, and snapshot file path settingsAdjust the windows to meet your needInformation of the CMSLog out of the current accountClose the software

Note

l CMS currently supports 5 languages: English, Smplified Chinese, Traditional Chinese, Russian andKorean.


2.2.2 Logout

Click →[Log out] to exit the current account, or click to exit the CMS.

Figure 2-2-3 Log Out

Note

l Password is necessary for logging out.


3. Manage3.1 Device Management

The Milesight CMS supports to add Milesight cameras and NVRs to get an efficient andconvenient management. The devices also can be removed or logged out from the CMS atany time.

3.1.1 Adding DevicesThere are two measures available for adding devices. First of all, click the Add button [+]→[Device].

Figure 3-1-1 Adding Device


u Adding a Single DeviceMilesight CMS provides to add device one by one. Please refer to the steps as follows:

Step1: Click the button;Step2: Select the device type, “NVR” or “Camera”;Step3: Enter device information;

Figure 3-1-2 Adding Device Manually

The meanings of the items on the page can be referred to the table 3-1-1.

Table 3-1-1 Adding Device ManuallyItem Function Introduction

Device Type Camera and NVR are available

Name Name of the device

IP Address The IP address of the device

Port The port of the device, the default port is 80, old model is 1100

User Name The user name of the device, “admin” for the default

Password

Enter the password for the account of the device, and defaultpassword for:

1. IPC: ms12342. NVR:For version *.7.0.6 and above: ms1234

For version *.7.0.5 and below: 123456

Transport Protocol TCP and UDP are available

Stream ModeThere are three options, “Auto”, “Primary Stream” and “SecondaryStream”


Once the device has been added successfully, there will pop up a window as follows:

Figure 3-1-3 Adding Device Successfully

u SearchMilesight CMS Supports to search devices automatically in the same network and add groupdevices with the same user name and password. Please refer to the steps as follows:

Step1: Click button to search the Milesight devices in the same network;Step2: Select the devices;Step3: Enter the user name and password of the selected devices, “admin” and “password”for the default user name and password;

Step4: Click button, there will pop up a window to remind you whether thedevices are added successfully or not.Step5: Click the [OK] button;Step6: Click [Refresh] button to refresh the status of the added devices.

Figure 3-1-4 Adding Group Device


Note

l Clicking button to refresh the status of the added devices.l Clicking button can select all devices which were found;l The devices found can be ranked by their IP, Port, Type, MAC, Model when you click the

corresponding button.l Up to 64 devices can be added;


3.1.2 Removing or Logging Out the Device

Milesight CMS supports to remove the added device for group or single. First of all, enterthe [Device Manage] page and do the steps as follows:

u Removing a Single DeviceThe steps to remove a Single device are as follows:

Step1: Click the button followed by the selected device;Step2: Click [OK] to remove the device or [Cancel] button to cancel the action when the

window pops up;

Figure 3-1-5 Removing a single Device


u Removing Group DevicesThe steps to remove the devices for a group are as follows:

Step1: Click to select all the added devices or check the checkbox to selectseveral devices;

Step2: Click the to remove the selected devices;

Step3: Click the [OK] to remove the devices or [Cancel] button to cancel the action when thewindow pops up;

Figure 3-1-6 Removing Group Device


3.1.3 Logout the Added DeviceYou can log out the added device for a moment rather than to remove the device in casethat the device will be used again next time. Logging out device can be understood asdisabling the device in case it needs to be enabled next time.

You can click the button to log out the device, and the icon will turn into ;

Figure 3-1-7 Logging Out the Added Device on Device Management PageOr right-click the selected device and choose [Log out].

Figure 3-1-8 Logging Out the Added Device on Live View Page

Note

l You can click the button on Device Management page or right-click the device on Live Viewpage and choose [Log in] to log in again.


3.1.4 Editing Device

Click the Edit button to edit the added device. Except the Device Type and IP address,the other parameters can be edited. The interface is as follows:

Figure 3-1-9 Editing Device


3.2 Device Config

Device Config provides Channels, Record and System three parts for NVR while Video, Event,Record and System four parts for Camera to set the devices.

3.2.1 NVRThe NVR Configuration page is as follows:

Figure 3-2-1 NVR Page

3.2.1.1 ChannelsChannels

Channels management provides searching, adding, editing, deleting channels function. Asfor searching and deleting channels, please refer to the Chapter III Device Management 3.1

Adding Device, here will not repeat again.


[Adding Channel]The main difference between adding the cameras which found by the CMS and addingcameras manually is that adding cameras manually can add other third party cameras viaONVIF and RTSP protocol.

Figure 3-2-3 Adding Channel

ONVIF: Camera which supports ONVIF protocol; RTSP: Primary: rtsp://IP:Port/main

Secondary: rtsp://IP:Port/sub(The default port for RTSP protocol is 554.)

MSSP is only for the Milesight products.


[Editing Channel]

Click the Edit button , there will pop up the edit window as follows:

Figure 3-2-4 Editting Channel

The parameters are the same as Adding Manually. You can edit the channel when adding itfirstly. Here will not repeat the steps again.


3.2.1.2 EventException

Click the Exception button, the setting window will pop up as follows:

Figure 3-2-5 Exception

The meanings of the items on the Exception page can be referred to the table 3-2-1 below:

Table 3-2-1 ScheduleItem Function Introduction

Exception Type There are “Network Disconnected”、“HDD Full”、“Record Full”&

“HDD Error”

Normal LinkageEnable or disable the Audio Warnings

Enable or disable the Linkage

After finishing the settings, you can click the Apply button to apply yoursettings to the CMS software.


Alarm I/O

Click the Alarm I/O button, the setting window will pop up as follows, you can configuratealarm input and output information:

Figure 3-2-6 Alarm Input / Output

The “Alarm Input” settings offers you to set up alarm input type, effective time, andcorresponding triggers.The “Alarm Output” settings offers you to set up alarm output type and effective time.

After setting up one channel, click the Apply button , and then click the Copy

button to copy the settings to other channels.


3.2.1.3 Record

ScheduleClick the Schedule button, the setting window will pop up as follows:

Figure 3-2-7 Record Schedule

The “Record Schedule” setting offers you to choose a specific channel and set a schedule forrecording, there are three status “No Record”, “Always Record” and “Record by schedule”.When enabling “No Record” and “Always Record”, the “Edit Schedule”button is always gray.If you want to set the record schedule, then you can do as follows:

Step1: Enabling “Record by Schedule”Step2: Click the “Edit Schedule” button, then the setting window will pop up as follows:

Figure 3-2-8 Edit Schedule


After setting the schedule for one channel, click the Apply button , and then click

the Copy button to copy to other channels.

Figure 3-2-9 Schedule Advanced

The meanings of the items on the Schedule page can be referred to the table 3-2-2 below:

Table 3-2-2 ScheduleItem Function Introduction

Channel Select the channel to set

Post Record Enable or disable the Post Record function

Duration Time There are several options to meet your need

Audio Record Enable or disable the Audio Record

Record Stream Type Main and Sub stream are available


After finishing the settings, you can click the Copy button to copy the settings

to the other channels. Click the Apply button to apply your settings to the CMSsoftware.

Figure 3-2-10 Copy to Other Channels

Holiday

Click the Holiday button, there will pop up the Holiday window. Click the Edit button to editthe selected holiday schedule as follows:

Figure 3-2-11 Holiday


Disk Management

Click the Disk Management to manage the disk, as the window shows, you can check thedisk status and format the disk. You can draw the blue bar to get more information aboutthe disk.

Figure 3-2-12 Disk Management


3.2.1.4 System

There are five parts in the System pages: General, Network, User, Status, Maintenance. Herewe will introduce them in more details.

General

Click the General button , there will pop up the windows as follows:

Figure 3-2-13 General

You can edit the device name and ID for your own, and choose the right time zone andwhether enable the Daylight Saving Time or not. It also supports to sync date and time with

NTP or set the time manually. After finishing the settings, click the Apply buttonto save and apply the settings to the CMS.


Network

In the Network part, you can use several network functions.

[Basic]Basic configuration includes working mode, IP Address, NetMask, Gateway, MTU, DNSserver, etc.

Figure 3-2-14 Basic[DDNS]

DDNS (Dynamic Domain Name System) can solve the problems from dynamic IP address.

Figure 3-2-15 DDNS


[Mail]

Check whether the SMTP port can be set or not. Please enable SSL/TLS according to actualmailbox. (Some SMTP server needs to secure connection)

Set the Sender E-mail Address, User Name, Password, and SMTP Server:

Figure 3-2-16 Mail

The meanings of the items on the Network page can be referred to the table below:

Table 3-2-3 MailItem Function Introduction

User Name The E-mail address you chosen to send emails

Password The password of the E-mail

SMTP Server The SMTP Server of your E-mail

Port The port of SMTP Server, it’s usually 25

EncryptionCheck the checkbox to enable SSL or TLS if it is required by the SMTPserver.

Host Name The host address of the E-mail

Sender Name Named by yourself for the Sender E-mail

Sender Address It must be the same as [User name]

Select Receiver You can have 3 receivers once

Receiver Name Named by yourself for the Receiver E-mail

Receiver Address E-mail Address for the receivers


[More]Secure Shell (SSH) has many functions; it can replace Telnet, and also provides a securechannel for FTP, POP, even for PPP.SSH Port:Check the SSH Enable checkbox to enable the feature and modify SSH ports according toactual application.RTSP Port:Real Time Streaming Protocol (RTSP) is an application layer protocol in TCP/IP protocolsystem.

The default RTSP port is 554. Please modify RTSP port according to actual application.

Figure 3-2-17 More

Note

l Check the DHCP checkbox if there is a DHCP server running in networks;l The valid range of MTU is 500~9676;l Do not input an IP address conflict with another device;l PPPoE user name and password can be obtained from your service provider. Once the setup is

completed, a connected status will be shown;l “Host name” can use letters, figures and hyphen (-), and must begin with letters;l You will get a snapshot every time for motion detection email sending;l If you use a port forward IP of NVR for the Host Name, please type the entire address including

the port;l The default SSH port is 22, and the default HTTP port for IE browser is 80, while the valid range of

RTSP port is 554 or 1024~65535;


UsersClick the Users button, there will pop up the setting window as follows:

Figure 3-2-18 User

There are three user levels “Admin”、“Operator” and “User” in User option, you can click

the Delete icon to delete “Operator” and “User” while unable to delete “Admin”. Click

the Edit icon , setting window will show as follows:

Figure 3-2-19 Edit User


The meanings of the items on the Edit User page can be referred to the table below:

Table 3-2-4 Edit User:Item Function Introduction

User Type You can set three types of user, Admin\Operator\User

User Name The User Name can not contain symbol

Password Set the password for different user type

Confirm password Make sure the same password as you set before

Basic PermissionShow the basic permission in different user types, you can scroll the bluebar to get more information

CameraConfiguration

Camera information in different user types

Click the Add button , the setting window will pop up as below:

Figure 3-2-20 Add User

Status

Status includes Device Information, Network Status, Camera Status, Event Status and DiskStatus. Status adopts the page form to display the contents.


[Device Information]From this page, you can check the Device ID, Device Name, Camera Number(The maximumnumber of camera can be added to the NVR), HDD number(The maximum number of HDDcan be supported to the NVR), Alarm Input Number, Alarm Output Number, Device SerialNumber, Firmware Version, Hardware Version, Uptime.

Figure 3-2-21 Device Information[Network Status]It will show you information about the network, including: Receive Bandwidth, Connection,Mode, DHCP, MTU(B), IP Address, Net mask, Gateway, MAC, Preferred DNS Server,Alternate DNS Server, Receive Rate, and Send Rate.

Figure 3-2-22 Network Status


[Camera Status]It will show you the Channel, Name, Enable or not, IP address, Record or not, Frame Rate,Bitrate, Resolution of main stream, Status of connection.

Figure 3-2-23 Camera Status

[Event Status]The icon will turn to red when the device is in the event status:

Figure 3-2-24 Event Status


[Disk Status]It will show you the Disk port, Vendor, Status, Total capability, Used capability, Freecapability HDD type, In use or not and Recycle Mode on or off.

Figure 3-2-25 Disk Status

Maintenance

Click the Maintenance button , there will pop up the window as follows, you can choosethe log and photo retention period for 1/2/4/6/8/10/12 months or permanent in AutoMaintenance part. And for the System Management part, you can click the Reboot button

to reboot the CMS.

Figure 3-2-26 Maintenance


3.2.2 CameraThe Camera Configuration page is as follows:

Figure 3-2-27 Camera

3.2.2.1 Video

Video

The Video page is as follows:

Figure 3-2-28 Video


The meanings of the items on Video page can be referred to the table below:Table 3-2-5 Video

Parameters Function Introduction

Video Codec H.265/H.264/MJPEG available

Frame SizeOptions include 4M(2592*1520),3M(2048* 1536), 1080P(1920*1080),2M(1600 *1200), 1.3M(1280*960), 720P(1280*720), D1 (704*576)

Maximum FrameRate

Maximum refresh frame rate of per second

Bit RateTransmitting bits of data per second, this item is optional only if youselect the H.264

Bit Rate ControlCBR: Constant Bitrate. The rate of CBR output is constant

VBR: Variable Bitrate. VBR files vary the amount of output date per timesegment

I-frame IntervalSet the I-frame interval to 1~120, this item is optional only if you selectthe H.264

ImageThe Image page is as follows:

Figure 3-2-29 Image


The meanings of the items on Image page can be referred to the table below:

Table 3-2-6 Image


Video Stream Choose the stream which you want to edit

Show Video Title Check the checkbox to show video title

Video Title OSD content customized

Text Position OSD position on the image

Display Date Check the checkbox to display date on the image

Date Position Date display position on the image

Date Format The format of date

WDRWide Dynamic: This function enables the capture and display of bothbright and dark areas in the same frame, there are details in both areasin this way

Flicker Control 60HZ flicker for NTSC mode and 50HZ flicker for PAL mode

Day/Night Mode

There are several parameters such as Exposure Level, Maximum ExposureTime and IR-CUT Interval, etc. associated with this mode

Night Mode: Shown in live view based on Night Mode settings

Day Mode: Shown in live view based on Day Mode settings

Auto Mode: Shown in live view based on environment

Customize: Shown in live view based on your own settings’ time tostart/end Night Mode

Start/End time of night Choose the start and the end of night time

Mirror

There are four options available, you can select one to meet your need

Normal: Remain the image in normal directionFlip Horizontal: Flip the image horizontallyFlip vertical: Flip the image verticallyRotating 180°: The images is presented upside down


Privacy Mask

Milesight CMS supports privacy mask. The steps are as follows:

Step1: Check the checkbox to enable the Privacy Mask function;

Step2: Choose the mask type

Step3: Hold down the mouse to draw the area and click button to applysettings;

Step4: Click the button to clear all drawn area;

Figure 3-2-30 Privacy Mask


AudioThis audio function allows you to hear the sound from the camera or transmit your sound tothe camera side. A two-way communication is also possible to be achieved with this feature.Alarm can be triggered when the audio input is above a certain alarm level you set, andconfigured audio can be played when an alarm occurs.

Figure 3-2-31 Audio

The meanings of the items on Audio page can be referred to the table below:

Table 3-2-7 Audio


Enable AudioCheck the checkbox to enable audio feature

Audio Mode: Only Mic, Only Speaker, Both Mic and Speaker are available

Audio Input

Denoise: Set it as On/Off. When you set the function on, the noisedetected can be filtered

Encoding: G711-ULaw, G711-ALaw and AAC LC are available

Sample Rate: There are 8KHz/16KHz two options

Input Gain: Input audio gain level, 0-100

Alarm Level: Alarm will be triggered if voice alarm is enabled and inputgained volume is higher than the alarm level, 0-100

Output Volum: Output level, 0-100


3.2.2.2 Event

Motion Detection

Check the checkbox to enable the Motion Detection function, you can draw the interested

area or click the Select All button to select all area interested. And the sensitivityranges from 0 to 100. Here are four options for alarm action, [Upload Via FTP], [Upload ViaSMTP], [Save Into SD Card], and [External Output]. And click the Edit Schedule button

to edit the time to enable the Motion Detection, then apply the settings.

Figure 3-2-32 Motion Detection


Alarm I/O

Enable the function first before you using the function. CMS supports several alarm actionswhen alarm triggered. FTP and SMTP must be set already before you use the alarm function.

Figure 3-2-33 Alarm I/O

Audio Alarm

Audio Alarm requires to enable Audio function first. CMS supports several alarm actionswhen alarm triggered. FTP and SMTP must be set already before you use the alarm function.

Figure 3-2-34 Audio Alarm


Exception

There are Network Lost and IP Conflict two kinds of Alarm Type available, the page is asfollows:

Figure 3-2-35 Exception

Note

l Please finish the relevant settings in the Network part before using the the Alarm function onCMS;

l It will activate the alarm when the current status is different from normal status on Alarm I/Opage, you can set the status yourself to meet your need;


3.2.2.3 Record

Record

CMS supports to record video in SD card of camera. You can set the record file size from10M to 256M, select the record frame type for All or Key and set the time to record. TheRecord page is as follows:

Figure 3-2-36 Record


3.2.2.4 System Date&Time

You can select the time zone and decide whether to enable the Daylight Saving Time or not.It also supports to sync date and time with NTP or set the time manually. After finishing the

settings, click the Apply button to save and apply the settings to the CMS.

Figure 3-2-37 Date&Time

Network

[Network]

The Network page is as follows:

Figure 3-2-38 Network


[SMTP]

Alarm video files can be sent to specific mail account through SMTP server. You mustconfigure the SMTP settings correctly before using it.

Figure 3-2-39 SMTP

The meanings of the items on SMTP page can be referred to the table below:

Table 3-2-8 SMTPParameters Function Introduction

User Name The sender's name. It is usually the same as the account name

Sender Email address to send video files attached to emails

Password The password of the sender

Server The SMTP server IP address or host name(e.g.smtp.gmail.com)

PortThe port of SMTP server. The default TCP/IP port for SMTP is 25(notsecured). For SSL/TLS port, it depends on the mail you use

To Email Email address to receive video files

Encryption Check the checkbox to enable SSL or TLS if it is required by the SMTP server.

[FTP]


Alarm video files can be sent to specific FTP server. You must configure the FTP settingscorrectly before using it.

Figure 3-2-40 FTP

The meanings of the items on FTP page can be referred to the table below:

Table 3-2-9 FTPParameters Function Introduction

Server FTP server address

Server Port The port of the FTP server. Generally it is 21

User Name User name used to log in to the FTP sever

PasswordUser password

FTP Folder Name Path where video will be uploaded to on the FTP server


[DDNS]DDNS allows you to access the camera via domain names instead of IP address. It managesto change IP address and update your domain information dynamically. You need to registeran account from a provider.

Figure 3-2-41 DDNS

The meanings of the items on FTP page can be referred to the table below:Table 3-2-10 DDNS


Enable DDNS Check the checkbox to enable DDNS service

NameSupport DDNS from now dyndns.org, freedns.afraid.org, www.no-ip.com,www.zoneedit.com, PlanetDDNS.com

User name Account name from the DDNS providerPassword Account password

Host name DDNS name enabled in the account[Port]You can set HTTP and RTSP port here.

Figure 3-2-42 Port

http://www.dyndns.com/

http://freedns.afraid.org/

http://www.no-ip.com/

http://www.zoneedit.com/


UsersThis part is for camera users option. You can add, edit and delete the Operator or Viewaccount while the Admin only allows to change the Password. When you selected the addedaccount, the background color of the account will turn to gray and the Authority will beselected the relevant option.

Figure 3-2-43 Users

SystemThe System page is as follows:

Figure 3-2-44 System


The meanings of the items on FTP page can be referred to the table below:

Table 3-2-11 SystemParameters Function Introduction

Device NameThe device name can be customized. It will be seen in file names of videofiles

Product ModelThe product model of the camera

Hardware Version The hardware version of the camera

Software Version The software version of the camera can be upgraded

MAC Address Media Access Control address

Click the button to reboot the device

Click the button to reset the settings to the default one.

Click the button to import the firmware file from PC, and click the

button to upgrade.


3.3 Users

You can add, edit and delete the Operator or View account while the Admin only allows tochange the Password. The Add User page is as follows:

Figure 3-3-1 User


4. View

4.1 Live View

Live View page provides user with PTZ, Image configuration, View Settings, Carouselfunctions. Enter the Live View page, the interface is as follows:

Figure 4-1-1 Live View

After adding the device, you can drag it or double click it to display the view windows. Thereare 1/4/8(1+7)(4+4)/9/16/36/64 several options of view windows.

The toolbar on this page is as follows:

Figure 4-1-2 Toolbar


The meanings of the items can be referred to the table below:

Table 4-1-1 Toolbar

Item Function Introduction

Cursor

Pan, click the button and enable electronic zoom the live view

PTZ

Image

Save View, save the current view to replace the old view

New View, create a new view

Carouse

Fullscreen

Stop All, stop all live view

Multi screen，up to four screens

/ / 1/4/9 Windows Button

Click the button to get more options of display windows

/ [Pre Page]/[Next Page] button


4.1.1 Live view interface Device

Device column in the live view shows what kind of device are connected to the CMS now:

Figure 4-1-3 Live view device

Right-click on device column:


Rename Reset the name of the camera on the list

Refresh Refresh the status of the NVR

Play Play the live view of the chosen device

Stop Stop the live view of the chosen device

Play all Play all the live view

Stop all Stop all the live view

Log out Log out of the CMS

RemoteConfiguration

Configure the camera

Synchronize Name Synchronize device name with the device

Synchronize AllName

Synchronize all name with the device


There are steps to display device under the Device mode:Step1: Make sure the device is available;Step2: Select one window to display;Step3: Right click a camera and choose [Play] to display the camera. When you choose

a NVR, there is [Play All] to display all cameras linked with the NVR. Youalso can double click the device or drag it into the selected window.

Table 4-1-2 Icon meanings of the device


/ Camera/NVR, which is connected

/ Camera/NVR, which is not connected

/ Camera/NVR, which logs out

List Button, click the button to list all cameras linked with the NVR

View

Right-click on View:


Play View Play the ViewDelete View Delete the View

Rename View Rename the View

Save Save the current view to replace the old

Save as Save the current view into a new View

View is a more convenient strategy to play live view. You can set several View and save a lotof time to play at the next time. The steps are as follows:

Step1: Click the New View button to create a new View;Step2: Display the cameras according to Device Part;

Step3: Click the Save View button to save the live view. You can right-click the View andchoose the [Play View].

Note

l Double clicking a NVR will lead to display all the cameras linked with the NVR;l Once a window is selected, it’s border color will turn into white;


4.1.2 Settings of Display the Live ViewThe toolbar of the Live View window:

Start/Stop recording Snapshot Full screen Stop the live view

Click the Menu button →[Configura on] to set the path to save the Record and Snapshotfiles, which will list by the date for the default.

Figure 4-1-4 System Config

Right-click the live view window, the interface is as follows:

Item Function IntroductionStop Stop playing the live view16:9 Ratio of long and width is 16:9

4:3 Ratio of long and width is 4:3Resize Suit the size to the windows

Stream Type Three stream types availablePrevious Screen Turn to the previous screen

Next Screen Turn to the next screenFull Screen Display windows in full screen


PTZ

Click the PTZ button , there will be a same button in the bottom-left corner of theselected window. Click the button in window, the PTZ function interface will appear. Theinterface is as follows:

Figure 4-1-5 PTZ


Table 4-1-3 PTZItem Function Introduction

Zoom

Focus

Iris

/ More or less level to set the selected PTZ function

Light On/OFF

Brush On/Off

Auto Focus

The level of Speed, you can draw the progress bar to set the speed ofPTZ action

Preset directions of Speed Dome Camera


Image

Click the Image button , there will be a same button in the bottom-left corner of theselected window. Click the button in window, the Image function interface will appear. Theinterface is as follows:

Figure 4-1-6 Image


Table 4-1-4 ImageItem Function Introduction

Brightness

Contrast

Saturation

Sharpness

Noise Reduction

Restore the image parameters to the default setting


4.2 Playback

CMS supports playback according to recorded time. Play recorded files in specified timeperiod, the Playback page is as follows:

Figure 4-2-1 Playback

You can refer to the steps as follows to playback the recorded files:Step1: Select the desired devices by checking the checkbox of the devices; the NVR has List

button to list the added cameras;Step2: Choose the date of which typeface is blue(blue means there is record files, black

means no files and red means weekend), the background will turn to blue once the

date is selected; then click the Search button to show；

Step3: Check the time line to select the time to playback; there are four colors meaning

different record files; click the button to get the previous/next page of channels;put the mouse on the time line and scroll up or down to zoom in/out the time;

Step4: Select the window, window border will turn into white once the window is selected;the first window is default window;

Step5: Click the Play button to playback; Speed Down, Speed Up and Single Step areavailable;

Step6: Select the NVR, choose cameras playback -> left-click the mouse on the selected time

line -> click the Cut button -> left-click again in different place then you can cut

a part of the playback file -> click Download button to back up the NVR playbackfiles;


Right-click the window during playback, it will pop up the interface as follows:


Stop Stop playing the playback view

Stop All Stop all the playback windows

16:9 Ratio of long and width is 16:9

4:3 Ratio of long and width is 4:3

Resize Suit the size to the windows

Capture Capture a snapshot

Full Screen Playback windows in full screen


5. Tools

5.1 E-Map

In this part, you can add an electronic map and draw the different cameras to the map. Thedisplay of map graphics in the Map window and the size of the map can be controlled, andthe map can be moved in the window to show the area you want to view. The E-Map page isas follows:

Figure 5-1-1 E-Map

Step1: Click the Add button to add an electronic map

Step2: Draw the different cameras to the map

Step3: Use the zoom in / zoom out buttons or with the mouse wheel to adjust the map

size, click the Resize button to restore the size of the map.

Step4: Right-click the hot spot, select the [Play] to play the live view of the hot spot.

Step5: Right-click the hot spot, select the [Delete] or click the Hot Delete button todelete the hot spot;

Step6: Click Map Delete button to delete the electronic map.


5.2 Logs

The logs contain the information about the time and IP that has accessed the camerathrough web. The Logs page is as follows:

Figure 5-2-1 Logs

The meanings of the item can be referred to the table below:

Table 5-2-1 Log


Main Type There are three main log types: [All], [System Log], [Operation Log]

Sub TypeOn the premise of main type has been selected, select the sub type tonarrow the range of logs

Start Time The time log starts

End Time The time log ends

Click the button to search the matched logs

Export the log file

You can click the bar to list the log by items such as Log ID, Time, User, Main Type, Sub Type,Device Name, Device Type,etc. You can also select the page to show in the right-bottom.


6. Service

6.1 Service

Milesight Technology Co., Ltd provides customers with timely and comprehensive technicalsupport services. End-users can contact your local dealer to obtain technical support.Distributors and resellers can contact directly with Milesight for technical support.

Technical Support Mailbox: [email protected]

Web: http://www.milesight.com

Online Problem Submission System: http://www.milesight.com/service/feedback.asp

Address: No.23Wanghai Road,2nd Software Park, Xiamen,China

Zip Code: 361006

TEL: +86-592-5922772

FAX: +86-592-5922775

Milesight

More in Sight

mailto:[email protected]


http://www.milesight.com/service/feedback.asp

Milesight CMS Central Management System - use-IP Ltd CMS User Manual.pdf · The Milesight Central...

Documents

Transcript of Milesight CMS Central Management System - use-IP Ltd CMS User Manual.pdf · The Milesight Central...