Microcontroller Based3rd Phase Project
-
Upload
mailtoakhils -
Category
Documents
-
view
232 -
download
0
Transcript of Microcontroller Based3rd Phase Project
-
7/27/2019 Microcontroller Based3rd Phase Project
1/23
MICROCONTROLLER BASEDRPM COUNTER
PRESENTED BY: AKHIL S (03)&
AKHIL R (04)Guided by:
-
7/27/2019 Microcontroller Based3rd Phase Project
2/23
INTRODUCTION
Counting the revolutions per minute (RPM) of motors,
determining the motor speed.
Essential in the field of industrial automation.
Useful for closed-loop control systems.
Proper action can be taken, actual RPM deviates from the setRPM.
-
7/27/2019 Microcontroller Based3rd Phase Project
3/23
AIM
Project based on microcontroller AT89C4051 that measuresand shows on an LCD the RPM of a running motor.
Using a proper transducer, first the rotations of the motor are
converted into pulses.
The generated pulses are counted by the microcontroller fora fixed time (say, one second).
The count is multiplied by a factor to get the exact RPM andthen displayed; if time is one second, the factor is 60.
-
7/27/2019 Microcontroller Based3rd Phase Project
4/23
Block diagram of the RPM counter
based on microcontrollerAT89C4051
-
7/27/2019 Microcontroller Based3rd Phase Project
5/23
Block Diagram Description
RPM counter based on AT89C4051 microcontroller that generates pulsesfor every rotation of the motor, counts them and shows on the LCD.
On a fixed base,light source on one side and the combination of a light-
dependent resistor (LDR), pulse generator, microcontroller and LCD onthe other side.
Both the arrangements are housed in separate wooden cabinets such thatthe light beam falls directly on the LDR.
The motor is placed on top of the l source. A slotted wheel(optical shaftencoder) is attached to the motor shaft. The wheel is so big that it caninterrupt the light beam falling on the LDR.
-
7/27/2019 Microcontroller Based3rd Phase Project
6/23
As the motor rotates, the slotted wheel also rotates.
The light beam falls on the LDR whenever the slot aligns with
the light beam and LDR, producing one pulse.
The rotations of the motor are converted into pulses that canbe counted by the program in the microcontroller.
Pulses are counted for one second. The pulse count is
multiplied by 60 (because 1 RPM = 60 RPS) and finally shownon the LCD.
-
7/27/2019 Microcontroller Based3rd Phase Project
7/23
Circuit of the RPM counter using
AT89C4051
-
7/27/2019 Microcontroller Based3rd Phase Project
8/23
5 V DC REGULATED POWER SUPPLY
SYSTEM
-
7/27/2019 Microcontroller Based3rd Phase Project
9/23
Components Required
Semiconductors:
IC1 - AT89C4051 MICROCONTROLLER
IC2 - NE555 TIMER
T1 - 2N2222 npn transistor
D1 - 1N4007 rectifier diode
LED1,LED2 - 5mm LEDLCD - 16x2 line
Resistors (all -watt, 5% carbon):
R1-R4 - 1 kilo-ohm
R5 - 150 ohm
R6 - 220 ohmR7 - 10 kilo-ohm
R8 - 470 ohm
VR1 - 10 kilo ohm preset
-
7/27/2019 Microcontroller Based3rd Phase Project
10/23
Capacitors :
C1 - 1uf, 16V electrolytic
C2 - 0.01uf ceramic disk
C3,C7 - 0.1uf ceramic diskC4,C5 - 22pf ceramic disk
C6 - 10uf, 16 V electrolytic
C8 - 100uf, 16 V electrolytic
Miscellaneous:S1 - ON\OFF switch
S2 - Push-to-on switch
XTAL - 12MHZ crystal
LDR
-
7/27/2019 Microcontroller Based3rd Phase Project
11/23
Circuit description
Figure shows the circuit of the RPM meter. It comprises microcontrollerAT89C4051, timer NE555, LCD module (162 line) and a few discrete
components.
Timer NE555 is configured as a monostable multivibrator whose time
period depends upon the combination of resistor R1 and capacitor C1.
Trigger pin 2 of NE555 is pulled high via resistor R2.
The LDR is connected along with resistor R2 to pin 2 of NE555 such that
when the light falls on the LDR, pin 2 goes low to trigger NE555.
-
7/27/2019 Microcontroller Based3rd Phase Project
12/23
The output from pin 3 of NE555 is inverted by transistor T1 and fed toport pins P3.3 and P3.4 of the microcontroller. LED2 is connected to port
pin P3.0 (pin 2) of the microcontroller.
Data pins D0 through D7 of the LCD are connected to port pins P1.0through P1.7 of the microcontroller, respectively.
Control pins E, RS and R/W of the LCD are connected to port pins P3.2,P3.5 and P3.7, respectively.
A 12MHz crystal connected between pins 4 and 5 of the microcontroller,along with two 22pF capacitors C4 and C5, generates the basic clockfrequency.
Power-on reset is derived with the combination of resistor R7 andcapacitor C6. Switch S2 is used for manual reset.
-
7/27/2019 Microcontroller Based3rd Phase Project
13/23
WORKING :
1.As the motor starts rotating, the light falls on the LDR when
the slot aligns with the laser beam and LDR.
2. Every time the motor completes one rotation, the
monostable (NE555) triggers to generate one pulse, which isindicated by LED1.
3. As the first pulse arrives, it generates an interrupt for the
microcontroller and immediately the microcontroller startscounting the pulses. This is indicated by LED2.
-
7/27/2019 Microcontroller Based3rd Phase Project
14/23
4. The microcontroller counts the pulses for a period ofone second. Thereafter, LED2 goes off.
5.The microcontroller stores the count and multiplies itby 60 to give the final RPM count
6. The count is in hex format, so you have to convert itinto decimal first.
7. The decimal values are converted into ASCII andshown on the LCD one by one.
-
7/27/2019 Microcontroller Based3rd Phase Project
15/23
Circuit TOP
-
7/27/2019 Microcontroller Based3rd Phase Project
16/23
POWER SUPPLY TOP
-
7/27/2019 Microcontroller Based3rd Phase Project
17/23
Circuit PCB Layout
-
7/27/2019 Microcontroller Based3rd Phase Project
18/23
POWER SUPPLY PCB
-
7/27/2019 Microcontroller Based3rd Phase Project
19/23
SOFTWARE
Software for the RPM counter is written in C
language.
Compiled using Keil Vision3 compiler.
Burned the generated .hex file into the
microcontroller using a suitable programmer.
-
7/27/2019 Microcontroller Based3rd Phase Project
20/23
FEATURES
Safe and accurate rpm measurements
Consume less power
LCD display gives RPM reading exactly with noguessing or errors
-
7/27/2019 Microcontroller Based3rd Phase Project
21/23
FUTURE SCOPE
Modern automobile engines & Aircraft
engines
Ultrasonic dental drills
Analogue audio recording & cd players
Turbo chargers
Zippe-type centrifuge used in isotope enrich
-
7/27/2019 Microcontroller Based3rd Phase Project
22/23
REFERENCES
Electronics For You (EFY)
http://www.electronicsforu.com/electronicsforu/circuitarchives/view_arti
cle.asp?sno=476&id=4690
Muhammad Ali Mazidi, Janice Gillespie Mazidi, The 8051Microcontroller and Embedded Systems, Seventh Edition, Pearson
Education Asia (2004).
Wikipedia
http://en.wikipedia.org/wiki/Tachometer
http://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=476&id=4690http://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=476&id=4690http://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=476&id=4690http://en.wikipedia.org/wiki/Tachometerhttp://en.wikipedia.org/wiki/Tachometerhttp://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=476&id=4690http://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=476&id=4690http://www.electronicsforu.com/electronicsforu/circuitarchives/view_article.asp?sno=476&id=4690 -
7/27/2019 Microcontroller Based3rd Phase Project
23/23
THANK YOU