MEDICAL RANGE - Eagle Lighting · 2015. 5. 25. · Cleanroom IP54: 12 Cleanroom CLB: 13 ......

24
MEDICAL RANGE

Transcript of MEDICAL RANGE - Eagle Lighting · 2015. 5. 25. · Cleanroom IP54: 12 Cleanroom CLB: 13 ......

  • MEDICAL RANGE

  • INTRODUCTION

    The following catalogue contains a range of luminaires suitable for use in medical facilities or applications where a clean environment is required.

    © Eagle Lighting Australia 2013 All rights reserved.

    DISCLAIMER:

    Whilst every effort has been made to ensure the accuracy of the information in this publication, ELA assumes no responsibility for errors, omissions or typographical errors.

    All goods supplied by Eagle Lighting Australia are subject to our general terms and conditions.

    For further information on any of the products featured in this catalogue, please contact your local Sales Representative.

    CONTENTS

    Caring Environments 05Patient Consideration 06Florence Elite 07Visible Improvements 08Welcoming Environment 09Gondol 10Cleanroom IP44 11Cleanroom IP54 12Cleanroom CLB 13Secureroom 14Secureroom SLB 15Operating Theatre Light 16Aureled Vista 18

  • NO OTHER PHYSICAL SITUATION CREATES SUCH UNIQUE LIGHTING DEMANDS AS A HOSPITAL BUILDING. PATIENT COMFORT AND WELL-BEING REQUIRE PRIMARY CONSIDERATION, ALONGSIDE PROVISION OF A GOOD WORKING ENVIRONMENT FOR STAFF, WHILE ENERGY CONSERVATION AND LIFECYCLE COSTS ARE ALSO OF MAJOR IMPORTANCE.

    PATIENT WELL BEING

    Research confirms the direct link between light quality and patient recovery rates. Recent studies show that an improved ward environment results in a reduction in non-operative patient recovery times of 21%.

    With the average cost of in-patient care running at $1307 per day, this represents a significant annual saving. From an operational point of view, there are clear consequential benefits in terms of shorter bed occupancy, faster patient turn-round and improved efficiency.

    WORKING ENVIRONMENT

    Hospital staff need good lighting to perform daily duties effectively, especially with the flexibility that different work areas demand. Lighting also influences comfort and stress levels, and improvements in these contribute to reduced absences and increased productivity.

    ENERGY SAVINGS

    The potential for wasted energy in hospitals is higher than in most buildings, with many areas working on a 24/7 basis. Good lighting design and installation will deliver major longterm energy savings, with corresponding cost benefits.

    Days inHospital

    ModernHospital

    2000+

    OlderPost/Pre-War

    Hospital

    1 2 3 4 5 6 7

    4.5

    Day

    s

    6.85

    Day

    s

    LIFECYCLE COSTS AND THE 1:5:200* RULE

    For a typical hospital building, lifecycle costing indicates that for every $1 spent on construction, $5 is required for facilities management and no less than $200 in costs associated with the people who use it. Lighting is a significant factor in this equation, and choosing the right system and equipment can make a dramatic difference to long-term project viability.

    RELATIVE EXPENDITURE

    HEALTHCARE LIGHTING EXPERTS

    To meet all these special requirements requires a special kind of lighting service, based on a deep understanding of the needs of patients, staff and visitors, and a sound grasp of the practicalities of building design and construction.

    With extensive experience of lighting hospitals, exceptional lighting design expertise and the ability to provide innovative solutions for every different internal environment, Eagle Lighting Australia is perfectly placed to meet those needs.

    * Source - The Long-Term Cost of Owning and Using Buildings Evans, Harigott, Haste and Jones, Royal Academy of Engineering, November 1998.

    STAFF EXPENDITURE FACILITIES MANAGEMENT CONSTRUCTION COSTS

    $200 $1$5

    CARING ENVIRONMENTSNo other physical situation creates such unique lighting demands as a hospital building.

    Modern Hospital

    2000+

    OlderPost/pre-War

    Hospital

  • KEEPING CONTROL

    To cater for varying patient needs and staff activities, wards need to operate in six different lighting modes : resting, reading, examination, night-time, watchlight and emergency.

    PATIENT COMFORT

    Patient comfort is optimised by eliminating glare and providing soft ambient lighting. Patient control integrated into a nurse call hand set enables patients to modify lighting levels. At the same time, central control allows staff to reset levels for a whole room at the touch of a switch.

    With low positioning and ease of access, the lighting units can also be more easily maintained and cleaned, helping to improve efficiency and control infection.

    PATIENT CONSIDERATIONSimple, easy control of lighting levels in wards and nursing stations

  • FLORENCE ELITE Low profile IP40 direct/indirect bedhead luminaire.

    4

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C

    FLORENCE ELITE

    EL-FEL3921 1 x 39W UP/1 X 21W DOWN T5 895 213 95

    EL-FEY2415LED 2400 LUMENS UP/1500 LUMENS DOWN (DALI)

    895 213 95

    TECHNICAL INFORMATION

    Optics

    Light source options: + LED 2400 lumens 26W* uplight (ward lighting)

    + LED 1500 lumens 20W* downlight (reading/nursing care)

    OR + 1 x 39W (44W)* T5 uplight (ward lighting)

    + 1 x 21W (25W)* T5 downlight (reading/nursing care)

    *Total power consumption including driver/ballast

    Uplight – wide integrated reflectors to maximse efficiency

    Downlight – Nano prism diffuser for maximum patient comfort

    Medium power LEDs deliver 50,000hrs life to L70

    Both the ward and reading light sources are independently dimmable by “push control” so the following lighting levels can be selected to meet the following requirements:

    Patient rest 30-50 Lux

    Watch light 15-20 Lux

    Reading 300 Lux

    General nursing care 300 Lux

    LED version requires DALI controls and onsite commissioning

    Body

    IP40

    Extruded aluminium spine & ‘push on’ moulded end caps

    One piece membrane diffuser for maximum infection control

    Wall mounted, recommended mounting height 2m for typical 2.6m-3m ceiling heights

    1st fix wall bracket, pre-wired to GST 18/4 flying leads

    No visible screws

    OPTIONS

    + Seismic Restraint

    N18226

    C A

    B

    DIME NS IONS

    L W H KG

    895 213 95 5.0

    FLO

    REN

    CE

    ELIT

    E

    florence elite low profile IP40 direct/indirect bedhead luminaire

    Optics• Light source options:

    – LED 2400 lumens 26W* uplight (ward lighting) – LED 1500 lumens 20W* downlight (reading/nursing care)

    Or

    – 1 x 39W (44W)* T5 uplight (ward lighting) – 1 x 21W (25W)* T5 downlight (reading/nursing care)

    *Total power consumption including driver/ballast

    • Uplight – wide integrated to maximse

    • Downlight – Nano prism di�user for maximum patient comfort

    • Medium power LEDs deliver 50,000hrs life to L70• Both the ward and reading light sources are independently

    dimmable by “push control” so the following lighting levels can be selected to meet LG2 requirements: – Patient rest 30-50 Lux – Watch light 15-20 Lux – Reading 300 Lux – General nursing care 300 Lux

    • LED version requires DALI controls and onsite commissioning

    Body• IP40

    • Extruded aluminium spine & ‘push on’ moulded end caps

    • One piece membrane di�user for maximum infection control

    • Wall mounted, recommended mounting height 2m for typical 2.6m-3m ceiling heights

    • 1st wall bracket, pre-wired to GST 18/4 leads

    • No visible screws and easy/cleaning access to the top of the luminaire

    Order Codes

    Florence Elite Standard

    T5 1 x 39W up/1 x 21W down (Switch Dim) FEL3921 LED 2400 lumens up/1500 lumens down (DALI) FEY2415

    To Specify Direct/indirect wall mounted hospital bed head luminaire using LED or T5 light source with separately switched dimmable ward lighting and reading/nursing care light. Easy to clean, IP40 rated extruded aluminium body with one piece infection control di�user membrane – as Whitecroft Lighting FLORENCE ELITE

    Lamp PerformanceWattage IL@25°C Lamp Life1 x 21W T5 1900 24,000hrs1 x 39W T5 3100 24,000hrs

    H L

    W

    Dimensions

    L W H KG 895 213 95 5.0

    7m

    7m

    100 luxFloor

    Compact Pleiad G2 2x26W Downlight

    300 lux

    5m

    3.6m

    100 luxFloor

    En Suite

    Typical 4 Bed Ward Typical 1 Bed Ward

    300 lux

    40IP

    322 HealthcareTYPICAL 4 BED WARD VS TYPICAL 1 BED WARD

    FLO

    REN

    CE

    ELIT

    E

  • 400 LUX

    100%

    25%

    100%

    3%

    5%

    5%

    300 LUX

    100LUX

    5LUX

    10LUX

    400 LUX

    100%

    25%

    100%

    3%

    5%

    5%

    300 LUX

    100LUX

    5LUX

    10LUX

    EXAMINATION

    Medical practices carried out at bed space with curtains drawn.

    400 LUX

    100%

    25%

    100%

    3%

    5%

    5%

    300 LUX

    100LUX

    5LUX

    10LUX

    READING

    Directly on the pillow, may be used as an additional source for nursing tasks. If adjustable avoidance of glare to others is essential.

    400 LUX

    100%

    25%

    100%

    3%

    5%

    5%

    300 LUX

    100LUX

    5LUX

    10LUX

    GENERAL/EMERGENCY

    Centre ward illuminance should be sufficient to enable usual nursing procedures with consideration of overall ambience. Emergency lighting can also be incorporated into the central downlights.

    400 LUX

    100%

    25%

    100%

    3%

    5%

    5%

    300 LUX

    100LUX

    5LUX

    10LUX

    NIGHTLIGHT

    Downlight only, visual acuity low. Illuminance sufficient to allow staff and patients to move around. Should not disturb sleeping patients.

    WATCHLIGHT

    Downlight only, continuous observation after the main switch off.

    WARD ILLUMINANCE

    Eagle lighting Australia’s recommended ward lighting scheme combines bedhead mounted up/downlights with ceiling mounted downlights to give maximum flexibility. Lighting can be patient controlled to maximise comfort with central override for staff to pre-set configurations.

    PATIENT COMFORT

    For the optimum blend of patient comfort and ease of maintenance, offset asymmetric lighting is ELA’s preferred solution to achieve a uniform 200 lux in corridors.

    CENTRALLY MOUNTED

    This can cause overhead glare and discomfort as patients are moved along hospital streets and corridors.

    OFFSET TO THE SIDE

    Overhead glare is significantly reduced with a recessed luminaire fitted with an asymmetric specular reflector.

    IMPROVING EFFICIENCY

    Corridors are as important as any other area of a hospital, so the same considerations of patient comfort, staff effectiveness and logistical efficiency apply. Lighting design needs to address all these issues, while the practical demands of cleaning and maintenance also come into play.

    ELA’s experience and expertise are brought to bear fully in these situations, creating innovative solutions that provide the best possible lighting for all types of corridors. In particular, asymmetric distribution helps to reduce glare and create an anxiety-reducing environment, while longitudinal layouts improve both lighting quality and efficiency.

    For ease of maintenance, corridor lighting units are designed to leave ceiling voids clear for services,

    VISIBLE IMPROVEMENTSA practical and aesthetic lighting solution for corridors and hospital streets.

    Centrally mountedThis can cause overhead glare anddiscomfort as patients are movedalong hospital streets and corridors.

    Centrally mountedThis can cause overhead glare anddiscomfort as patients are movedalong hospital streets and corridors.

  • WELCOMING ENVIRONMENTSWelcoming, reassuring lighting for reception and communal areas.

    ENHANCING PATIENT EXPERIENCE

    Good lighting enhances patients’ experience in every area of a hospital, from the moment of arrival until final departure. The need to maintain a feeling of safety and security is crucial to that experience, especially in areas with easy public access and significant people movement.

    ELA solutions help to create a sense of well-being and comfort through sympathetic design and use of warm lamp colours. For patients, staff and visitors, security is further ensured by well-planned installations that eliminate dark corners and illuminate unoccupied areas.

  • TECHNICAL INFORMATION

    VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    1-10V/STD terminal block -300

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    1-10V/Fused terminal block -700

    SWINGING LAMP HOLDER FOR LAMP REPLACEMENT

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C

    GONDOL EXPOSED T-BAR

    EL-17631-100 1 x 28W T5 1200 300 75

    N18226

    Recessed mounted IP44 asymmetric wall washer luminaire suitable for T-Bar ceilings. The lamp is concealed in the luminaire and hidden from view.

    Asymmetrical light distribution for lighting vertical surfaces, the light sources lamp holder is pivoted so that the source can be moved into the light opening to facilitate re-lamping.

    Acrylic dust proof cover for ease of cleaning.

    OPTIONS

    + Seismic RestraintGONDOL 1x28W | LOR 80%

    GONDOL IP44 RATED A wall washing T-Bar luminaire complete with sealed gasket and clear acrylic cover.

    C

    B

    A

    44

    DIAGRAM OF WALLWASHING EFFECT

    GO

    ND

    OL

  • www.eaglelighting.com.au 45

    EPDM GASKET

    TECHNICAL INFORMATION

    VARIATION SUFFIX

    Non DIM/STD terminal block -0

    DSI/STD terminal block -1

    DALI/STD terminal block -2

    Standard/Fused terminal block -4

    DSI/Fused terminal block -5

    DALI/Fused terminal block -6

    Emergency (ATCO maintained) -8

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSWATTAGE EFFICACYlm/W

    LUMINOUS FLUX A B C CUTOUT

    CLEANROOM LED : BOTTOM ACCESS PLASTER RECESSED

    EL-CR44L-814000P-_ 1R 2600LM 4k Delta 20 83 1650 1260 315 120 1230 285

    EL-CR44L-824000P-_ 2R 5200LM 4k Delta 38.8 82 3172 1260 315 120 1230 285

    EL-CR44L-814200P-_ 1R 1300LM 4k Delta 9.7 84.5 820 660 315 120 630 285

    EL-CR44L-824200P-_ 2R 2600LM 4k Delta 20 82 1638 660 315 120 630 285

    EL-CR44L-824100P-_ 2R 5200LM 4k Delta 38.8 87 3380 1260 660 120 1230 630

    EL-CR44L-834100P-_ 3R 7800LM 4k Delta 58.5 87 5070 1260 660 120 1230 630

    EL-CR44L-844100P-_ 4R 10400LM 4k Delta 77.8 87 6760 1260 660 120 1230 630

    EL-CR44L-824300P-_ 2R 2600LM 4k Delta 20 84.5 1690 660 660 120 630 630

    EL-CR44L-834300P-_ 3R 3900LM 4k Delta 29.7 85 2535 660 660 120 630 630

    EL-CR44L-844300P-_ 4R 5200LM 4k Delta 38.8 86 3345 660 660 120 630 630

    The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.

    This range is rated IP44 from all angles.

    The Cleanroom IP44 LED fitting is ideal for areas where long running hours and difficult access for maintenance are a concern.

    The LED boards employed in the Cleanroom are Zhaga approved and can easily be changed or upgraded by two simple fixing screws. Using Zhaga approved boards ensures future availability and access to the latest developments in efficiency, colour quality and maintenace in the LED market.

    Seismic restraint as standard.OPTIONS

    + Sandwich Panel

    + Emergency

    + Colour temperature 3k, 4k or 5k

    N18226

    CLEANROOM IP44 LEDA range of luminaires developed for specialist ‘cleanroom’ applications

    Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -1

    P5 -2

    Delta -8

    CEILING TYPE SUFFIX

    Plaster -P

    Surface mounted -S

    T-bar -T

    IES INDOOR REPORTPHOTOMETRIC FILENAME : LL16298.IES

    POLAR GRAPH

    207

    414

    620

    827

    1

    Maximum Candela = 827.29 Located At Horizontal Angle = 0, Vertical Angle = 0# 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)

    Photometric Toolbox Professional Edition - Copyright 2002-2011 by Lighting Analysts, Inc.Calculations based on published IES Methods and recommendations, values rounded for display purposes.Results derived from content of manufacturers photometric file.

    Page 1

    CLEANROOM IP44 LED 1200x300 2600lm Delta

    TECHNICAL SPECIFICATIONS

    Total Luminaire Efficacy minimum > 69lm/W

    MacAdam 3 SDCM

    CRI > 84

    Lifetime 50,000hrs / L70

    Passive cooling

    System guarantee 5 years

    EXAMPLE ONLY

    CEILING TYPE

    COLOUR TEMP WIRING VARIATION

    DIFFUSER OPTION

    EL-CR44L-814000P-_B

    C

    A

    TOGGLE

    LED IP44

    CLE

    AN

    RO

    OM

    IP44

  • www.eaglelighting.com.au 47

    VARIATION SUFFIX

    Non DIM/STD terminal block -0

    DSI/STD terminal block -1

    DALI/STD terminal block -2

    Standard/Fused terminal block -4

    DSI/Fused terminal block -5

    DALI/Fused terminal block -6

    Emergency (ATCO maintained) -8

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -1

    P5 -2

    Delta -8

    CEILING TYPE SUFFIX

    Plaster -P

    Surface mounted -S

    T-bar -T

    TECHNICAL SPECIFICATIONS

    Total Luminaire Efficacy minimum > 69lm/W

    MacAdam 3 SDCM

    CRI > 84

    Lifetime 50,000hrs / L70

    Passive cooling

    System guarantee 5 years

    EXAMPLE ONLY

    CEILING TYPE

    COLOUR TEMP WIRING VARIATION

    DIFFUSER OPTION

    EL-CR44L-81H4000P-_

    EPDM GASKET

    TECHNICAL INFORMATION

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSWATTAGE EFFICACYlm/W

    LUMINOUS FLUX A B C CUTOUT

    CLEANROOM LED : BOTTOM ACCESS PLASTER RECESSED

    EL-CR44L-81H4000P-_ 1R 5000LM 4k High Output Delta 36 82 2950 1260 315 120 1230 285

    EL-CR44L-82H4000P-_ 2R 10000LM 4k High Output Delta 72 81 5828 1260 315 120 1230 285

    EL-CR44L-81H4200P-_ 1R 2500LM 4k High Output Delta 18 82 1475 660 315 120 630 285

    EL-CR44L-82H4200P-_ 2R 5000LM 4k High Output Delta 36 82 2949 660 315 120 630 285

    EL-CR44L-82H4100P-_ 2R 9600LM 4k High Output Delta 72 84 6048 1260 660 120 1230 630

    EL-CR44L-83H4100P-_ 3R 14400LM 4k High Output Delta 108.4 84 9126 1260 660 120 1230 630

    EL-CR44L-82H4300P-_ 2R 4800LM 4k High Output Delta 36 84.5 3042 660 660 120 630 630

    EL-CR44L-83H4300P-_ 3R 7200LM 4k High Output Delta 54.2 84 4563 660 660 120 630 630

    EL-CR44L-84H4300P-_ 4R 9600LM 4k High Output Delta 72 84.5 6084 660 660 120 630 630

    CLEANROOM IP44 LED HIGH OUTPUTA range of luminaires developed for specialist ‘cleanroom’ applications

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

    CLEANROOM IP44 LED HO 1200x300 5000lm Delta

    The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.

    This range is rated IP44 from all angles.

    The Cleanroom IP44 LED fitting is ideal for areas where long running hours and difficult access for maintenance are a concern.

    The LED boards employed in the Cleanroom are Zhaga approved and can easily be changed or upgraded by two simple fixing screws. Using Zhaga approved boards ensures future availability and access to the latest developments in efficiency, colour quality and maintenace in the LED market.

    Seismic restraint as standard.

    OPTIONS

    + Sandwich Panel

    + Emergency

    + Colour temperature 3k, 4k or 5kN18226

    Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg

    B

    C

    A

    1514

    1

    2

    1135

    378

    757

    TOGGLE

    LED IP44

    CLE

    AN

    RO

    OM

    IP44

  • TECHNICAL INFORMATION

    GASKET

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSA B C CUTOUT

    CLEANROOM T5 : BOTTOM ACCESS GASKETED PLASTER RECESSED

    EL-CR44-214-_02P-___ 2 x 14W T5 Plaster Recessed 660 315 120 630 285

    EL-CR44-314-_02P-___ 3 x 14W T5 Plaster Recessed 660 315 120 630 285

    EL-CR44-224-_02P-___ 2 x 24W T5 Plaster Recessed 660 315 120 630 285

    EL-CR44-324-_02P-___ 3 x 24W T5 Plaster Recessed 660 315 120 630 285

    EL-CR44-228-_00P-___ 2 x 28W T5 Plaster Recessed 1260 315 120 1230 285

    EL-CR44-328-_00P-___ 3 x 28W T5 Plaster Recessed 1260 315 120 1230 285

    EL-CR44-254-_00P-___ 2 x 54W T5 Plaster Recessed 1260 315 120 1230 285

    EL-CR44-354-_00P-___ 3 x 54W T5 Plaster Recessed 1260 315 120 1230 285

    EL-CR44-228-_01P-___ 2 x 28W T5 Plaster Recessed 1260 660 120 1230 630

    EL-CR44-328-_01P-___ 3 x 28W T5 Plaster Recessed 1260 660 120 1230 630

    EL-CR44-254-_01P-___ 2 x 54W T5 Plaster Recessed 1260 660 120 1230 630

    EL-CR44-214-_03P-___ 2 x 14W T5 Plaster Recessed 660 660 120 630 630

    EL-CR44-224-_03P-___ 2 x 24W T5 Plaster Recessed 660 660 120 630 630

    EL-CR44-414-_03P-___ 4 x 14W T5 Plaster Recessed 660 660 120 630 630

    44

    CLEANROOM 2x28W Y19 | LOR >70%

    8/

    CLEANROOM IP44 T5A range of luminaires developed for specialist ‘cleanroom’ applications

    The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.

    This range is rated IP44 from all angles.

    Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.

    A large variety of speciality lamp options are easily available for the Cleanroom IP44 T5 and T8 models, including high colour rendering options, long life versions and cyanosis index approved options.

    OPTIONS

    + Sandwich Panel

    + Emergency

    + Seismic Restraint

    N18226

    VARIATION SUFFIX

    Non DIM/STD terminal block -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    Emergency (ATCO maintained) -800

    Seismic restraint -900

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -1

    P5 -2

    Delta -8

    EXAMPLE ONLY WIRING VARIATIONDIFFUSER OPTION

    CEILING TYPELAMP TYPE

    EL-CR44-214-_02P-___

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

    Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg

    B

    C

    A

    updated: 21.10.2013

    TOGGLE

    CLE

    AN

    RO

    OM

    IP44

  • TECHNICAL INFORMATION

    GASKET TOGGLE

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION DIMENSIONSA B C CUTOUT

    CLEANROOM T8 : BOTTOM ACCESS GASKETED PLASTER RECESSED

    EL-CR44-218-_02P-___ 2 x 18W T8 Plaster Recessed 660 315 120 630 285

    EL-CR44-318-_02P-___ 3 x 18W T8 Plaster Recessed 660 315 120 630 285

    EL-CR44-236-_00P-___ 2 x 36W T8 Plaster Recessed 1260 315 120 1230 285

    EL-CR44-336-_00P-___ 3 x 36W T8 Plaster Recessed 1260 315 120 1230 285

    EL-CR44-236-101P-___ 2 x 36W T8 Plaster Recessed 1260 660 120 1230 630

    EL-CR44-336-101P-___ 3 x 36W T8 Plaster Recessed 1260 660 120 1230 630

    EL-CR44-436-101P-___ 4 x 36W T8 Plaster Recessed 1260 660 120 1230 630

    EL-CR44-218-103P-___ 2 x 18W T8 Plaster Recessed 660 660 120 630 630

    EL-CR44-318-103P-___ 3 x 18W T8 Plaster Recessed 660 660 120 630 630

    EL-CR44-418-103P-___ 4 x 18W T8 Plaster Recessed 660 660 120 630 630

    The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where the luminaire requires protection against contamination.

    This range is rated IP44 from all angles.

    Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.

    A large variety of speciality lamp options are easily available for the Cleanroom IP44 T5 and T8 models, including high colour rendering options, long life versions and cyanosis index approved options.

    OPTIONS

    + Sandwich Panel

    + Emergency

    + Seismic Restraint

    44

    CLEANROOM 2x36W Y19 | LOR >70%

    8/

    CLEANROOM IP44 T8A range of luminaires developed for specialist ‘cleanroom’ applications

    N18226

    VARIATION SUFFIX

    Non DIM/STD terminal block -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    Emergency (ATCO maintained) -800

    Seismic restraint -900

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -1

    P5 -2

    Delta -8

    EXAMPLE ONLY WIRING VARIATIONDIFFUSER OPTION

    CEILING TYPELAMP TYPE

    EL-CR44-214-_02P-___

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

    Weight of 1200x300 luminaire is 10.00kg Weight of 600x300 luminaire is 5.55kg Weight of 1200x600 luminaire is 18.20kg Weight of 600x600 luminaire is 10.80kg

    B

    C

    A

    362

    2

    91

    181

    272

    1

    updated: 21.10.2013

    CLE

    AN

    RO

    OM

    IP44

  • CLEANROOM IP54 RATEDA range of luminaires developed for specialist ‘cleanroom’ applications

    548/

    TECHNICAL INFORMATION

    VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    1-10V/STD terminal block -300

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    1-10V/Fused terminal block -700

    TORSION SPRING

    91

    182

    273

    364

    1

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C

    CLEANROOM T5 : BOTTOM ACCESS TRIPLE GASKET

    EL-CCL-214-_03-___ 2 x 14W T5 Plaster Recessed 650 650 135 615 615

    EL-CCL-314-_03-___ 3 x 14W T5 Plaster Recessed 650 650 135 615 615

    EL-CCL-414-_00-___ 4 x 14W T5 Plaster Recessed 650 650 135 615 615

    EL-CCL-228-_00-___ 2 x 28W T5 Plaster Recessed 1275 370 135 1230 340

    EL-CCL-328-_00-___ 3 x 28W T5 Plaster Recessed 1275 370 135 1230 340

    EL-CCL-235-_00-___ 2 x 35W T5 Plaster Recessed 1575 370 135 1530 340

    CLEANROOM T5 : TOP ACCESS TRIPLE GASKET

    EL-CCL-228-_01-___ 2 x 28W T5 Plaster Recessed 1275 350 135 1230 340

    EL-CCL-328-_01-___ 3 x 28W T5 Plaster Recessed 1275 350 135 1230 340

    CLEANROOM T8 : BOTTOM ACCESS TRIPLE GASKET

    EL-CCL-236-_00-___ 2 x 36W T8 Plaster Recessed 1275 370 135 1230 340

    EL-CCL-336-_00-___ 3 x 36W T8 Plaster Recessed 1275 370 135 1230 340

    CLEANROOM T8 : TOP ACCESS TRIPLE GASKET

    EL-CCL-236-_01-___ 2 x 36W T8 Plaster Recessed 1275 350 135 1230 340

    EL-CCL-336-_01-___ 3 x 36W T8 Plaster Recessed 1275 350 135 1230 340

    The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the clean environment.

    Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.

    OPTIONS

    + Plaster Recessed

    + Exposed T-Bar

    + Sandwich Panel

    + Emergency CO D16/ C90 D20 (3x36W Version)

    + Surface mounted version available upon request

    + Seismic Restraint

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -1

    P5 -2

    P7 -3

    Opal -5

    P20 -6

    P19 Silver tint -7

    CLEANROOM 2x28W | LOR 76%

    N18226 REVIT IES AGi32

    EXAMPLE ONLY

    WIRING VARIATION

    DIFFUSER OPTION

    LAMP TYPE

    EL-CCL-214-_03-___

    GASKET

    B

    C

    A

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

    CLE

    AN

    RO

    OM

    IP54

  • CLEANROOM CLB IP54 RATEDA range of luminaires developed for specialist ‘cleanroom’ applications

    54 IK10

    TECHNICAL INFORMATION

    VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    1-10V/STD terminal block -300

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    1-10V/Fused terminal block -700

    The Cleanroom range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the clean environment.

    Ensuring a clean and secure environment does not negate the need for excellent light control. With the CLB we have incorporated the Penta G2 Miro 5 louvre fixed into the frame for increased luminance and glare control protected by a clear acrylic overlay.

    Suitable for diverse applications such as hospitals, food preparation areas, pharmaceuticals manufacturing areas, fibre optic production areas and applications where a clean environment is required.

    OPTIONS

    + Plaster Recessed

    + Sandwich Panel

    + Surface mounted version available upon request

    + Polycarbonate (IK10)

    + Seismic Restraint

    GASKET

    97

    195

    292

    390

    1

    CLEANROOM CLB 2x28W | LOR 83%

    B

    C

    A

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C

    CLEANROOM CLB PLASTER RECESSED

    EL-CLB-214-100-_00 2 x 14W 650 370 100 620 290

    EL-CLB-224-100-_00 2 x 24W 650 370 100 620 290

    EL-CLB-314-100-_00 3 x 14W 650 450 100 620 400

    EL-CLB-324-100-_00 3 x 24W 650 450 100 620 400

    EL-CLB-414-100-_00 4 x 14W 650 650 100 620 510

    EL-CLB-424-100-_00 4 x 24W 650 650 100 620 510

    EL-CLB-228-100-_00 2 x 28W 1275 370 100 1230 290

    EL-CLB-254-100-_00 2 x 54W 1275 370 100 1230 290

    N18226 REVIT IES AGi32

    EXAMPLE ONLY

    LAMP TYPE WIRING VARIATION

    EL-CLB-214-100-_00

    TORSION SPRING

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

    CLE

    AN

    RO

    OM

    CLB

  • SEC

    UR

    ERO

    OM

    SECUREROOM IP65 RATEDA range of luminaires specifically developed for specialist cleanroom and security applications

    FD T2665 IK10

    TECHNICAL INFORMATION

    VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    1-10V/STD terminal block -300

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    1-10V/Fused terminal block -700

    PC2 Acrylic panel -P

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C

    SECUREROOM T5 BOTTOM ACCESS TRIPLE GASKET - PLASTER

    EL-CCL-214-_04-___ 2 x 14W T5 Plaster Recessed 700 700 135 630 630

    EL-CCL-314-_04-___ 3 x 14W T5 Plaster Recessed 700 700 135 630 630

    EL-CCL-228-_05-___ 2 x 28W T5 Plaster Recessed 1300 400 135 1230 340

    EL-CCL-328-_05-___ 3 x 28W T5 Plaster Recessed 1300 400 135 1230 340

    EL-CCL-235-_02-___ 2 x 35W T5 Plaster Recessed 1600 400 135 1530 340

    SECUREROOM T8 BOTTOM ACCESS TRIPLE GASKET - PLASTER

    EL-CCL-418-_05-___ 4 x 18W T8 Plaster Recessed 700 700 135 630 630

    EL-CCL-236-_02-___ 2 x 36W T8 Plaster Recessed 1300 400 135 1230 340

    EL-CCL-336-_02-___ 3 x 36W T8 Plaster Recessed 1300 400 135 1230 340

    NOTE : STANDARD COMPLETE WITH POLYCARBONATE. FOR PC2 ENVIRONMENT, ACRYLIC PANEL REPLACES POLYCARBONATE (ADD SUFFIX -P)

    EPDM GASKETTAMPERPROOF SCREW

    91

    182

    273

    364

    1

    The Cleanroom Security range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the secure environment.

    Suitable for diverse applications such PC2 laboratories, hospitals, psychiatric wards, police stations, high security, pharmaceutical manufacturing areas and applications where a clean and secure environment is required.

    OPTIONS

    + Sandwich Panel

    + Emergency CO D16 / C90 D20 (3x36W Version)

    + Surface mounted available upon request

    + PC2 Environments

    + Seismic Restraint

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -1

    P5 -2

    P7 -3

    Opal -5

    P20 -6

    P19 Silver tint -7

    SECUREROOM 2x28W | LOR 76%

    B

    C

    A

    N18226 REVIT IES AGi32

    EXAMPLE ONLY

    WIRING VARIATIONLAMP TYPE

    DIFFUSER OPTION

    EL-CCL-214-_04-___

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

  • SEC

    UR

    ERO

    OM

    SLB

    IK10

    SECUREROOM SLB IP65 RATEDA range of luminaires specifically developed for specialist cleanroom and security applications

    65

    TECHNICAL INFORMATION

    VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    1-10V/STD terminal block -300

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    1-10V/Fused terminal block -700

    PC2 Acrylic panel -P

    EPDM GASKETTAMPERPROOF SCREW

    The Cleanroom Security range of fixtures has been developed to meet the requirements of specialist installations, where a fully sealed luminaire is needed to prevent contamination of the secure environment.

    Having a clean and secure environment does not negate the need for excellent light control. With Secureroom SLB we have incorporated the Penta G2 Miro 5 louvre fixed into the frame for increased luminance and glare control.

    Suitable for diverse applications such PC2 laboratories, hospitals, psychiatric wards, police stations, high security, pharmaceutical manufacturing areas and applications where a clean and secure environment is required.

    OPTIONS

    + Sandwich Panel

    + Surface mounted available upon request

    + PC2 environments

    + Seismic Restraint

    97

    195

    292

    390

    1

    SECUREROOM SLB 2x28W | LOR 83%

    B

    C

    A

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C

    SECUREROOM SLB PLASTER RECESSED

    EL-SLB-214-100-_00 2 x 14W 700 400 100 620 290

    EL-SLB-224-100-_00 2 x 24W 700 400 100 620 290

    EL-SLB-314-100-_00 3 x 14W 700 500 100 620 400

    EL-SLB-324-100-_00 3 x 24W 700 500 100 620 400

    EL-SLB-414-100-_00 4 x 14W 700 700 100 620 510

    EL-SLB-424-100-_00 4 x 24W 700 700 100 620 510

    EL-SLB-228-100-_00 2 x 28W 1300 400 100 1230 290

    EL-SLB-254-100-_00 2 x 54W 1300 400 100 1230 290

    NOTE : STANDARD COMPLETE WITH POLYCARBONATE. FOR PC2 ENVIRONMENT, ACRYLIC PANEL REPLACES POLYCARBONATE (ADD SUFFIX -P)

    N18226 REVIT IES AGi32

    EXAMPLE ONLY

    WIRING VARIATIONLAMP TYPE

    EL-CLB-214-100-_00

    PLEASE NOTE: The cutout sizes shown above refer to only these specific product codes and no other Cleanroom products. If you are unsure of the cutout size required for your Cleanroom fitting, please ask your ELA representative.

  • OP

    ERA

    TIN

    G T

    HEA

    TRE

    OPERATING THEATRE LIGHT A range of luminaires specifically developed for operating theatre applications

    WIRING VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    1-10V/STD terminal block -300

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    1-10V/Fused terminal block -700

    Our Operating Theatre Light luminaires have been developed as a unique solution, meeting the requirements of specialist operating theatre installations, where a fully sealed luminaire is needed to prevent contamination of the secure environment.

    This range has been engineered specifically for hospitals, emergency and veterinarian operating theatres.

    OPTIONS:

    + Available in an IP44 Cleanroom, or IP65 Secureroom configuration, with bottom or ceiling access.

    + T5 or T8 lamp options in single or multiple configurations.

    + Operating Theatre Light can be installed with separate switching/dimming depending on requirements.

    + Seismic Restraint

    DIFFUSER PANEL OPTIONS SUFFIX

    P19 -100

    P5 -200

    P7 -300

    Opal -500

    P20 -600

    TECHNICAL INFORMATION

    B

    C

    A

    N18226

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONS†

    A B C

    OPERATING THEATRE LIGHT - BOTTOM ACCESS, TRIPLE GASKET - PLASTER RECESSED

    EL-OPS-228-_00-000* CORNER A 1300† 400† 135†

    EL-OPS-228-_01-000* CORNER B 1300† 400† 135†

    EL-OPS-228-_02-000* INTERMEDIATE 1300† 400† 135†

    EL-OPS-228-_03-000* INTERMEDIATE W/ CEILING ACCESS 1300† 400† 135†

    EL-OPS-228-_04-000* START 1300† 400† 135†

    EL-OPS-228-_05-000* END 1300† 400† 135†

    *PRODUCT CODES AND †DIMENSIONS LISTED ARE EXAMPLES AND APPLY TO 2 X 28W LAMP CONFIGURATION ONLY

    The Operating Theatre Light can be customised to your needs. Please consult with an ELA Representative regarding dimensions and product codes.

    The Operating Theatre Light is available in the following lamp configurations:

    T5 Lamp 14W 24W 28W 35W 49W 54W Single or Multiple Lamps

    T8 Lamp 18W 36W 58W Single or Multiple Lamps

    UNIQUE OVERLAPPING DESIGN EPDM GASKET & INSTALLATION BRACKETS

    OPERATING THEATRE 2x28W | LOR 76%

    91

    182

    273

    364

    1

    6544

    8/

    EL-OPS-228-_00-000WIRING VARIATIONEXAMPLE ONLY

    DIFFUSER OPTIONSLAMP CONFIGURATION

  • OP

    ERA

    TIN

    G T

    HEA

    TRE

    OPERATING THEATRE LIGHT A range of luminaires specifically developed for operating theatre applications

    FEATURES & BENEFITS

    EXAMPLE LAYOUTS Adapted from our highly successful Cleanroom and Secureroom range of luminaires, the Operating Theatre Light has been specifically developed to meet the demanding requirements of the theatre environment.

    FEATURES AND BENEFITS:

    + Together with an EPDM gasket, swing-out installation brackets negate the need for a silicon sealant around the fixture in the ceiling. EPDM rubber foam is a closed cell gasket, ensuring a high IP-rating. At less than 10% compression this returns a 100% water tightness. The low-memory nature of the material ensures it will always return to its original shape.

    + Overlapping design construction, provides this system with a continuous seal around the perimeter of the installation.

    + UV-stablised, acrylic diffuser options contribute to the overall IP65-rating, and are easily cleaned and maintained. When compared with polycarbonate options, our acrylic diffuser is resistant to hospital-grade cleaners.

    + By combining the acrylic diffuser with the multi-directional IP-rating of the Operating Theatre Light, the result is a luminaire that meets the tough standards required for a PC2 environment.

    + One of the features of meeting the PC2 standard is that zero contaminants can enter the luminaire - including from inside the ceiling cavity. This means the luminaire achieves high maintenance intervals.

    + A removeable gear tray allows for easy installation and maintenance.

    Designed and manufactured in Melbourne, Australia, the Operating Theatre Light has many unique features and capabilities, but most importantly offers a diverse range of options to suit applications with different constraints and requirements. Consult with your local ELA Representative to discuss your needs.

    The above example layouts demonstrate how the Operating Theatre Light system can be installed to create a fully sealed, contaminant-free environment. Example A. demonstrates a full theatre installation, utilising Corner modules, Example B. shows a single run making use of Start and End modules.

    2 2

    0

    1

    EXAMPLE A. EXAMPLE B.

    ITEM NO.

    DESCRIPTION QTY

    0 CORNER A 2

    1 CORNER B 2

    2 INTERMEDIATE 10

    ITEM NO.

    DESCRIPTION QTY

    2 INTERMEDIATE 2

    4 START 1

    5 END 1

    1 4

    0 5

  • AU

    REL

    ED V

    ISTA

    AURELED VISTAA slimline LED luminaire with a printed acrylic diffuser suitable for recessed mounting and T-bar ceilings.

    The Aureled Vista has been developed with healthcare enivronments in mind. The Aureled Vista is available with a range of different imagery designed to promote a relaxing and reassuring environment for patients.

    Using creative lighting solutions creates a non-institutional feel that puts patients at ease and makes it more likely that they relax and focus on healing.

    The Aureled Vista can be a focal and discussion point for young children undergoing medical examinations. By giving patients something to concerntrate on they are less likely to become agitated.

    Designed and constructed with a shallow 45mm profile the Aureled will slide into confined spaces. Coupled with a detachable gearbox incorporating a plug-and-play connector this luminaire is the perfect solution for locations where there are multiple services installed inside the ceiling space.

    Once installed, the gearbox can be detached from the luminaire housing as required whether for upgrading to dimming or maintenance.

    Available with:+ DSI Dimming+ DALI Dimming+ Emergency+ Colour Temperature 4k+ Seismic Restraint

    N18226

    (REMOTE GEAR)

    PRODUCT CODE LIGHT SOURCE/DESCRIPTION (NOM) DIMENSIONSA B C D

    AURELED VISTA EXPOSED T-BAR

    EL-AUR-____-C1-___ Aureled LED C1 600 600 45 40

    EL-AUR-____-C2-___ Aureled LED C2 600 1200 45 40

    EL-AUR-____-C3-___ Aureled LED C3 600 1800 45 40

    EL-AUR-____-C4-___ Aureled LED C4 1200 1200 45 40

    EL-AUR-____-C6-___ Aureled LED C6 1200 1800 45 40

    EL-AUR-____-C9-___ Aureled LED C9 1800 1800 45 40

    (REMOTE GEAR)

    AUTUMN 1 (AUT1)

    GALAXY 1 (GAL1)

    SKY 1 (SKY1)

    OCEAN 1 (OCE1)

    BUTTERFLY 1 (BUT1)

    SKY 2 (SKY2)

    AVAILABLE CONFIGURATIONS

    C1 C2 C3 C4 C6 C9

    EXAMPLE ONLY

    CONFIGURATION

    WIRING VARIATION

    IMAGE OPTION

    EL-AUR-AUT1-C9-000

    WIRING VARIATION SUFFIX

    Standard -000

    DSI/STD terminal block -100

    DALI/STD terminal block -200

    Standard/Fused terminal block -400

    DSI/Fused terminal block -500

    DALI/Fused terminal block -600

    PLEASE NOTE: If you would like to use an alternative image or an alternative configuration, please inform us and we will provide you with the required image specifications.

    P.O.A

    LED IP44

  • www.eaglelighting.com.au [email protected]

    VICTORIA 17-19 Jets Court Melbourne Airport VIC 3045 P 03 9344 7444 F 03 9344 7433

    NEW SOUTH WALES Unit 4, 21 Mars Road Lane Cove NSW 2066 P 02 9420 5799 F 02 9420 5988

    QUEENSLAND 53 Caswell Street East Brisbane QLD 4169 P 07 3891 0744 F 07 3891 0755

    AUSTRALIAN CAPITAL TERRITORY M 0411 889 406

    DISTRIBUTORS - AUSTRALIA

    WESTERN AUSTRALIA H.I. LIGHTING PTY LTD 111 Broadway Bassendean WA 6054 P 08 9377 1322 F 08 9377 1761

    SOUTH AUSTRALIA H.I. LIGHTING SA PTY LTD 8 Hender Avenue Magill SA 5072 P 08 8304 8500

    TASMANIA SOUTHERN LIGHTING & DISTRIBUTION 34 Federal Street North Hobart TAS 7000 P 03 6231 5599 F 03 6231 5211

    DISTRIBUTORS - NEW ZEALAND

    AUCKLAND FAGERHULT NEW ZEALAND Level 1, 18A Neilpark Drive East Tamaki, Auckland 2013 M +64 21 655 609 M +64 21 509 248

    WELLINGTON FAGERHULT NEW ZEALAND M +64 21 597 900

    SOUTH ISLAND

    P