Rubens (CLP-350N) Value Proposition 2008.1.15 B2B Product Marketing
Marbilano Technical Manual · 2020. 10. 23. · 350N EN ISO 10545 - 4 PROPERTIES BS EN : 14411 :...
Transcript of Marbilano Technical Manual · 2020. 10. 23. · 350N EN ISO 10545 - 4 PROPERTIES BS EN : 14411 :...
TECHNICAL MANUAL
THE UNIQUETECHNICAL PROPERTIES OF OUR COLLECTIONTogether with the raw materials and latest technological devices, Marbilano has admitted itself to guarantee the realization of Customer Satisfaction. In order to maintain the continuity of such satisfaction, Research and Development Department has been established and increasing product quality.The quality production is performed by delicately trained personnel from the top to the bottom. In order to maintain the continuity of an active quality system which has already proven that such a system can meet the needs of the importance of quality and quality needs.
TEST DESCRIBES AS PER BS EN: 14411:2016 (GROUP BLA) ANNEX-G, COMPLIES WITH ISO STANDARD ISO 13006:2018
Gloss is an optical property which indicates how well a surface reflects light in a specular direction. It is one of the important parameters that are used to describe the visual appearance of an tiles. The factors that affect gloss are the refractive index of the material, the angle of incident light and the surface topography.The glossiness of marbilano tiles is in range 95.5GU - 97.5GU
Glossiness
Average Glossiness = 96.5GU
L Values
Average L ValuesL = ~86.45
L Values indicates the lightness of Tiles from black (0) to white (100).The L-Value of marbilano tiles is in range 85.5 - 87
A tile’s modulous of rapture(MOR) is determined by applying a force on the middle of the topside of the piece. The force applied is increased until the tile breaks.Modulous of rapture(MOR) of marbilano tiles is in range 410 N - 440N
Modulous of Rapture (MOR)
MOR = 417.2 NModulus of Rupture
(MOR) N350N EN ISO 10545 - 4
PROPERTIES BS EN : 14411 : 2016ISO 13006 : 2018 TESTING METHOD
417.2N
MARBILANORESULT
Planarity or flatness of the tile fair face, evaluable by comparison with a plane through the side and centre curvature, and warpage (deviation in a corner from the plane formed by the other three corners).
Surface Planarity
Surface Planarity(mm)
± 1.8mm EN ISO 10545 - 2
PROPERTIES BS EN : 14411 : 2016ISO 13006 : 2018 TESTING METHOD
± 0.5mm
MARBILANORESULT
Size : 600 x 600mm
Size : 600 x 1200mm
Water Absorption
Water absorption measures how much moisture a specific type of tile is likely to absorb on an ongoing basis.The water absorption of marbilano tiles is in range 0.014% - 0.029%
Water Absorption(%)
≤ 0.500% EN ISO 10545 - 3
PROPERTIES BS EN : 14411 : 2016ISO 13006 : 2018 TESTING METHOD
0.024%
MARBILANORESULTAverage Water Absorption = 0.024%
Thickness is measured by first tracing the two diagonals, then measur-ing the thickest point along each of the four segments obtained. In the case of extruded tiles, four lines perpendicular to the direction ofextrusion are traced.The average thickness of 600 x 600mm tiles is ~8.52mm.The average thickness of 600 x 1200mm tiles is ~9.24mm.
Thickness
Average Thickness = 9.24mm
Average Thickness = 8.52mm
DEVIATION INTHICKNESS (mm) ± 0.5mm EN ISO 10545 - 2
PROPERTIES BS EN : 14411 : 2016ISO 13006 : 2018 TESTING METHOD
0.00 - 0.18mm
MARBILANORESULT
Size : 600 x 600mm
Size : 600 x 1200mm
600 x 1200mm
TECHNICAL SPECIFICATION
PROPERTIES
TEST EN: 14411 : 2016 (GROUP BLA.) ANNEX - G
STANDARD AS PER ISO 13006 : 2018
MARBILANORESULT
TESTING METHOD
Dimention and Surface QualityDeviation in Length ± 1 mm 0.00 - 0.10mm EN ISO 10545 - 2Deviation in Width ± 1 mm 0.00 - 0.10mm EN ISO 10545 - 2Deviation in Thickness ± 0.5mm 0.00 - 0.18mm EN ISO 10545 - 2Straightness of Sides ± 0.8mm 0.12 - 0.14mm EN ISO 10545 - 2Rectangularity ± 0.8mm 0.14 - 0.16mm EN ISO 10545 - 2Surface Flatness ± 1.8mm 0.00 - 0.15mm EN ISO 10545 - 2Surface quality 95% 100% free from defects EN ISO 10545 - 2
Physical Property
Water Absorption % ≤ 0.500% 0.020% EN ISO 10545 - 3Breaking Strength N ≥ 1300 2255.52N EN ISO 10545 - 4Modulus of Rupture (MOR) N/mm2 35 50.34N/mm² EN ISO 10545 - 4Resistance to surface abrasion PEI Class - IV 2100 Revolu�on pass EN ISO 10545 - 7Coefficient of Linear Thermal Expansion 9 x 10 6 Max 5.23 x 10 6 EN ISO 10545 - 8Thermal Shock Resistance 10 cycle Min confirm EN ISO 10545 - 9Crazing Resistance No crazin in two cycle confirm EN ISO 10545 - 11Moisture Expansion (mm/mm) 0.02 mm/m Max. 0.00 mm/m Max. EN ISO 10545 - 10Impact Resistance 0.55 Min. 0.58 EN ISO 10545 - 5Scrach hardness of Surface (mohs scale) 5 moh's scal 5 moh's IS 13630 - 13Bulk density (g/cc) 2.2 Min. 2.2913 g/cc EN ISO 10545 - 3
Chemical Property
Resistance Stain Min Class - 3 Min Class - 5 EN ISO 10545 - 14Resistance to Low Concentration of Acid & Alkali Min Class - GLC Class - GLA EN ISO 10545 - 13Resistance to High Concentration of Acid & Alkali Min Class - GHC Class - GHA EN ISO 10545 - 13Resistance to house chemical Min Class - GC Class - GA EN ISO 10545 - 13Resistance to swimming pool salt Min Class - GC Class - GA EN ISO 10545 - 13Lead and Cadium Release ≤0.1 mg/dm² 0.00 mg/dm² EN ISO 10545 - 15