Monoplace Hyperbaric Oxygen Chamber

Manufacturing Diving & Hyperbaric Chambers

O2mono

Manufacturing Diving & Hyperbaric Chambers

1

2

O2mono CHAMBER

The Baroks O2mono Model Monoplace Hyperbaric Treatment System consists of one

compartment, is designed to safely provide hyperbaric oxygen therapy to patients at pressure

up to 2 bar( 3ATA). Monoplace chamber is designed according to European Standarts and is

tested according to EN14931 requirements.

Only quality-certified “Special Steel” with test reports is used in our Monoplace Chamber

production. In addition; before production of the chamber, ultrasonic lamination tests and after

welding process; x-ray, magnetic particle and ultrasonic tests (Non-destructive tests) have

been done by professional engineering staff. All these process is controlled and reported by

certification company. After chamber production, hydrostatic tests is done by the certification

authority surveyors

The chamber has cylindrical shape and one entrance door

3

We are manufacturing two type monoplace chamer : Half Acrylic (HA) and Full Acrylic (FA).

General view of two types

Half Acrylic (HA) O2mono Full Acrylic (FA) O2mono

4

Monoplace HBOT Chamber; are designed to treat a single person pressurized with 100% oxygen.

Figure General O2mono Body

Chamber consists of below mentioned parts

Table 1: Chamber Parts

No Part Name

1 Cylindrical Body

2 Torispherical Head

3 Door

4 Body Wall

5 Viewport

6 Nozulles

5

Cylindrical Shell (Body)

The chamber length is 1000 mm and inner diameter is 900 mm.

The square door size of the chamber is 1050 mm. X 1050 mm and it provides entrance and

exit easily.

Door

Door size is 1050 mm X 1050 mm.

And thickness is 40 mm. It has also

locking mechanism for safety.

Figure Door Parts

The below table shows technical specifications about monoplace chamber system.

TECHNICAL SPECIFICATIONS

Working Pressure 3 ATA (2 bar)

Hydrostatic Test Pressure 4 ATA (3 bar)

Working Temperature 0C and 45C

Chamber Capacity 1 Person

Inner Diameter 900 mm.

Chamber Length (Inside) 2,221 mm.

Total Length 2494 mm.

Material Pressure Steel

Door Number 1

Door Opening 900 mm.

Weigth ≈ 1.5 ton

Electrical Power Requirement 3 KW

Electrical Connection Voltage 220 Volt, 50 Hz

Approved By TUV

6

Lock Mechanism

The door of the system can be opened or closed by using Lock Arm. The system cannot be

pressurized if both lock key and door key are not closed. Camshaft provides maximum sticking

on the door Automatic Locking Cylinder locks the door when the pressure reaches 0,1 bar.

Viewport

Viewports are manufactured from PMMA:( Poly Methl Meth Acrylate ) material where

chemical and physical properties are given in ASME PVHO standard. .

7

CHAMBER EQUIPMENTS This chapter consists of complementary /supportive equipments inside/on the chambe

Figure Chamber Equipments

Kod Parça Adı

1 Painting

2 Breathing System

3 Safety Valves

4 Stretcher

5 Entertaintment Monitor

6 Temperature and Humidity Sensor

7 Pressure Sensor

8 Antistatic Wrıst Strap

8

Painting

The chambers are covered with flame retardent non-toxic epoxy paint on both exterior

and interior surfaces. The paint, due to its flame retardency property starts burning at

high temperatures, the burning only ensuses at the centre of the heat source and is

extinguished by itself when it is removed. Also the the fumation that ensues during

burning is not toxic for humans. This feature also prevents any sickness that may ensue

because of the natural fumation spread by the paint because of nominal heat.

Breathing System

Breathing system provides required breathing air/oxygen to patients and evacuates

exhaust air via exhaust system

Drager X-Plore 3300 BIBS mask is a breathing mask that is used to deliver the treatment

gas to the patient.

Avox Inlet Regulator Avox Outlet Regulator

9

CONTROL PANEL

Figure O2mono Control Panel

No Part Name

1 Counter

2 Door Locking Button

3 Temperature Indicator

4 Humidity Indicator

5 CO2 Indicator

6 Chamber Pressure

7 O2 Source Pressure Manometer

8 Air Source Pressure Manometer

9 Chamber Pressure

10 Flowmeter

11 O2 Analyzer

12 Patient Warning Reset Button On/Off

13 Patient Warning Alarm

14 Door Locked Light

15 Pressure Inside Light

16 Set Pressure

17 TV On/Off

18 Emergency Stop Button

19 Intercom

20 System On/Off Button

21 BIBS Mask Air or O2 Selection

22 Auxiliary Exhaust

23 Decompression

24 Compression

25 Chamber Selection Air or O2

9 7

4

3

10

12

19

5

11

2

21 8

14

22 23 24

6

1

13

15

20

18

25

17

16

10

O2mono Control panel consist of the following equipment’s which enables the operator take

control of the chamber safely and reliable. All main operations and functions of the chamber

can be done with this panel .The control panel of the hyperbaric chamber is located on the

chamber and provides following operations.

• Treatments control

• Maintain and adapt the interior environment of the chamber

• Communication and lighting

• Supply, evacuation and exchange of the medical working gases

• Monitoring of important information such as humidity, temperature and oxygen

concentration and patients.

11

ENTERTAINTMENT UNIT

During the treatment session, an LCD entertainment monitor is mounted on the chamber to

spend time during the treatment. It provides opportunity to watch video and TV to patient.

POWER SUPPLY UNIT

O2mono electric system generally;

Power Stage

Communication

Digital Indicators

Analyzers

The electrical system is supplied with 220V AC. It is also reduced 24V

DC using electronic transformers.

Communication System consists of the operator and operator warning

system.

Digital indicators show pressure, temperature, humidity and CO2 value

shows.

Oxygen and carbon dioxide analyzer is available.

The input voltage system 220 V AC ± 10%, frequency 50 Hz ± 5%. There is power supply in

order to support the system at least 30 minutes in cases where input voltage is not present,

cut or go beyond the limit value.

LCD Monitor

12

PATIENT TRANSFER UNIT

Stretcher is used for patient transferring and it consists of two parts as chamber internal

stretcher and transfer stretcher. Internal stretcher is transported with transfer stretcher while

the patient is transported into the chamber by pushing The stretcher is designed for working in

hyperbaric conditions as mechanically.

Figure Stretcher

13

14

15

Adress: Aydıntepe Mah. Dinçel Sk. No:1 Lider Plaza Kat:4 34947 TUZLA – ISTANBUL, TURKEY

www.baroks.eu info@baroks.eu

http://www.baroks.eu%0binfo@baroks.euhttp://www.baroks.eu%0binfo@baroks.eu