MANUAL TP-LINK ACCESS POINT LOBBY.pdf

8/12/2019 MANUAL TP-LINK ACCESS POINT LOBBY.pdf

1/24

Quick Installation Guide

DAP-1150

Wireless Access Point Supporting Router Mode


2/24

DAP-1150 Quick Installation Guide

BEFORE YOU BEGIN

Delivery Package

Access point DAP-1150

Power adapter DC 5V/1.2

Straight-through Ethernet ca!e "CA# 5E$

CD-%&' with (User Manual) and (Quick Installation Guide)

(Quick Installation Guide) "rochure$.

*+ an, o+ the ites are issing p!ease contact ,our rese!!er.

!Using a power supply with a different voltage rating than the one

included will cause damage and void the warranty for this product.

Default Settings

IP addess o! access "oint 192.168.0.50

Usena#e $lo%in& admin

Pass'od admin

Na#e o! 'ieless net'ok $((ID& DAP-1150

System Requirements and Equipment

A coputer with an, operating s,ste that supports a we rowser.

A we rowser to access the we-ased inter+ace o+ the access point

indows *nternet Ep!orer 'oi!!a 3ire+o or &pera.

A 4*C "Ethernet or i-3i adapter$ to connect to the access point.

An 02.11 g or n i-3i adapter to create a wire!ess networ6.

)


3/24


*ONNE*+ING +O P*

PC with Ethernet Adapter

1. 'a6e sure that ,our PC is powered o++.

2. Connect an Ethernet ca!e etween the 7A4 port !ocated on the ac6

pane! o+ the access point and the Ethernet port o+ ,our PC.

8. Connect the power cord to the power connector port on the ac6 pane! o+

the access point then p!ug the power adapter into an e!ectrica! out!et or

power strip.

9. #urn on ,our PC and wait unti! ,our operating s,ste is cop!ete!,!oaded.

4ow ,ou shou!d con+igure ,our PC to otain an *P address autoatica!!, "as

D:CP c!ient$.

,


4/24


Obtaining P Address Aut!maticallyin OS "ind!ws #P

1. C!ic6 the (tatutton and proceed to the *ontol Panel Net'okand Intenet *onnections Net'ok *onnectionswindow.

2. *n the Net'ok *onnectionswindow right-c!ic6 the re!e;ant .ocalAea *onnection icon and se!ect the Po"eties !ine in the enudisp!a,ed.

8. *n the .ocal Aea *onnection Po"etieswindow on the Genealta se!ect the Intenet Potocol $+*P/IP& !ine. C!ic6 the Po"eties

utton.


5/24


9. Se!ect the Otain an IP addess auto#aticall2 and Otain DN(se3e addess auto#aticall2radio uttons. C!ic6 the O4utton.

5. C!ic6 the 6utton in the connection properties window.

4ow ,our coputer is con+igured to otain an *P address autoatica!!,.

5


6/24


Obtaining P Address Aut!matically in OS "ind!ws $

1. C!ic6 the (tatutton and proceed to the *ontol Panelwindow.2. Se!ect the Net'ok and (7ain% *ente section. "*+ the Contro! Pane!

has the categor, ;iew "the *ate%o2;a!ue is se!ected +ro the 8ie' 2drop-down !ist in the top right corner o+ the window$ choose the 8ie'net'ok status and tasks !ine under the Net'ok and Intenetsection.$

8. *n the enu !ocated on the !e+t part o+ the window se!ect the *7an%eada"te settin%s !ine.

9. *n the opened window right-c!ic6 the re!e;ant .ocal Aea *onnectionicon and se!ect the Po"eties!ine in the enu disp!a,ed.

5. *n the .ocal Aea *onnection Po"eties window on theNet'okin%ta se!ect the Intenet Potocol 8esion $+*P/IP3&!ine. C!ic6 the Po"etiesutton.

9


7/24



8/24


PC with "i%&i Adapter

1. Connect the power cord to the power connector port on the ac6 pane! o+

the access point then p!ug the power adapter into an e!ectrica! out!et or

power strip.

2. #urn on ,our PC and wait unti! ,our operating s,ste is cop!ete!,

!oaded.

8. #urn on ,our i-3i adapter. As a ru!e odern noteoo6s with ui!t-in

wire!ess 4*Cs are e>uipped with a utton or switch that turns on/o++ the

wire!ess adapter "re+er to ,our PC docuents$. *+ ,our PC is e>uipped

with a p!ugga!e wire!ess 4*C insta!! the so+tware pro;ided with ,our

i-3i adapter.

4ow ,ou shou!d con+igure ,our i-3i adapter.

;


9/24


C!nfiguring "i%&i Adapter in OS "ind!ws #P

1. C!ic6 the (tatutton and proceed to the *ontol Panel Net'okand Intenet *onnections Net'ok *onnectionswindow.

2. Se!ect the icon o+ the wire!ess networ6 connection and a6e sure that

,our i-3i adapter is on.

8. Search +or a;ai!a!e wire!ess networ6s.

9. *n the opened


10/24


C!nfiguring "i%&i Adapter in OS "ind!ws $

1. C!ic6 the (tatutton and proceed to the *ontol Panelwindow.

2. Se!ect the Net'ok and (7ain% *ente section. "*+ the Contro! Pane!has the categor, ;iew "the *ate%o2;a!ue is se!ected +ro the 8ie' 2drop-down !ist in the top right corner o+ the window$ choose the 8ie'net'ok status and tasks !ine under the Net'ok and Intenetsection.$

8. *n the enu !ocated on the !e+t part o+ the window se!ect the *7an%eada"te settin%s !ine.

9. *n the opened window se!ect the icon o+ the wire!ess networ6 connectionand a6e sure that ,our i-3i adapter is on.

5. #o open the !ist o+ a;ai!a!e wire!ess networ6s se!ect the icon o+ the

wire!ess networ6 connection and c!ic6 the *onnect +outton or !e+t-c!ic6 the networ6 icon in the noti+ication area !ocated on the right side o+

the tas6ar.

10


11/24



12/24


*ONFIGURING A**E(( POIN+

C!nnecting t! "eb%based nterface

1. Start a we rowser.

2. *n the address ar o+ the we rowser enter the *P address o+ the access

point ", de+au!t the +o!!owing *P address is speci+ied

192.168.0.50$. Press the Ente6e,.

8. &n the opened page enter the usernae "!ogin$ and password +or the

adinistrator account ", de+au!t the +o!!owing usernae and password

are speci+ied admin admin$. #hen c!ic6 the Ente!in6.

!

*+ the error (The page cannot be displayed) "or (Unable to display thepage)/(Could not connect to remote server)$ occurs upon connecting to

the we-ased inter+ace o+ the access point a6e sure that ,ou ha;e

proper!, connected the de;ice to ,our coputer.

1)


13/24


%ight a+ter the +irst access to the we-ased inter+ace ,ou are +orwarded to the

page +or changing the adinistrator password speci+ied , de+au!t.

Enter the new password in the Pass'od and *on!i#ation+ie!ds. #henc!ic6 the (a3eutton.

!

%eeer or write down the new password +or the adinistrator

account. *n case o+ !osing the new password ,ou can access the settings

o+ the access point on!, a+ter restoring the +actor, de+au!t settings ;ia

the hardware %ESE# utton. #his procedure wipes out a!! settings that

,ou ha;e con+igured +or ,our de;ice.

1,


14/24


A+ter success+u! registration the access point?s >uic6 settings page opens.

&n the page ,ou can proceed to the i-3i Setup iard "use the *on!i%ueuic6 settings page +ro the i-3i Setup iard or an,

we-ased inter+ace enu section !e+t-c!ic6 the D-7in6 !ogo in the top !e+t

corner o+ the page.

#he we-ased inter+ace o+ the access point is u!ti!ingua!. Se!ect a needed

!anguage +ro the enu disp!a,ed when the ouse pointer is o;er the

.an%ua%ecaption. @ou can change the !anguage o+ the we-ased inter+acein an, enu ite.

A+ter se!ecting the !anguage the noti+ication on unsa;ed changes wi!! e

disp!a,ed. C!ic6 the (a3eutton to sa;e the current !anguage o+ the we-

ased inter+ace as the de+au!t !anguage.

1


15/24


Selecting Operating '!de

, de+au!t the access point ode is speci+ied +or the de;ice. *+ ,ou need to use

the de;ice as a router proceed to the Ad3anced / De3ice #odepage se!ectthe Route;a!ue +ro the Reoot;a!ue +ro the top-page enu disp!a,ed whenthe ouse pointer is o;er the (2ste#caption and wait unti! the de;ice isreooted.

!hen the de;ice is switched to the router ode ,ou cannot connect to

it ;ia a wired connection.

A+ter the de;ice has reooted the >uic6 settings page in the router ode

opens.

&n the opened page ,ou can proceed to the iards "use the *onnect tointenet ?ost site and *on!i%ue


16/24


C!nfiguring "ireless (etw!rk

, de+au!t the wire!ess networ6 o+ the access point is open "it re>uires no

password to access it$. #o a;oid unauthoried access to ,our wire!ess !oca!

area networ6 change the de+au!t settings o+ the access point.

Example of Wireless Settings

1. Bo to the


17/24


C!nfiguring )!cal Area (etw!rk

1. Bo to the Net / .ANpage. *+ needed change the *P address o+ the accesspoint?s 7A4 inter+ace and the as6 o+ the !oca! sunet in the IPAddessand Net#ask+ie!ds. #hen c!ic6 the (a3eutton.

2. , de+au!t the D:CP ser;er o+ the de;ice is ena!ed. *n the D?*P

se3esection ,ou can change the paraeters o+ the D:CP ser;er. As aru!e the D:CP ser;er shou!d e disa!ed when the de;ice is used in the

access point ode "se!ect the Disale;a!ue +ro the @odedrop-down!ist$.

8. A+ter speci+,ing the D:CP ser;er settings c!ic6 the (a3eutton.

1:


18/24


C!nfiguring C!nnecti!n t! the nternet*R!uter '!de Only+

!

@ou shou!d con+igure ,our A4 connection in accordance with datapro;ided , ,our *nternet ser;ice pro;ider "*SP$. 'a6e sure that ,ou

ha;e otained a!! necessar, in+oration prior to con+iguring ,our

connection. &therwise contact ,our *SP.

1. Bo to the Net/


19/24


5. *+ ,our *SP uses 'AC address inding in the Et7enetsection in the@A* +ie!d enter the 'AC address registered , ,our *SP uponconc!uding the agreeent. #o set the 'AC address o+ the networ6

inter+ace card "o+ the coputer that is eing used to con+igure the access

point at the oent$ as the 'AC address o+ the A4 inter+ace c!ic6 the*lone @A* utton. #o set the address o+ a de;ice connected to theaccess point?s 7A4 at the oent se!ect the re!e;ant ;a!ue +ro the

drop-down !ist !ocated to the right o+ the +ie!d.


20/24


=. For connection of Static IP type in the IP section +i!! in the IPAddess Net#ask Gate'a2 IP Addess and Pi#a2 DN(se3e+ie!ds.

. For connection of Dynamic IP type i+ ,our *SP has pro;ided the address

o+ the D4S ser;er in the IP section dese!ect the Otain DN( se3eaddesses auto#aticall2 chec6o and +i!! in the Pi#a2 DN(se3e+ie!d.

)0


21/24


. For connection of PPTP + Static IP or !TP + Static IP type in the IPsection +i!! in the IP Addess Net#ask Gate'a2 IP Addess andPi#a2 DN( se3e +ie!ds. #hen in the 8PN section enterauthoriation data pro;ided , ,our *SP "the usernae "!ogin$ in the

Usena#e +ie!d and the password in the Pass'od and Pass'odcon!i#ation+ie!ds$ or se!ect the uired. *n the 8PN se3e addess+ie!d enterthe *P or %7 address o+ the PP#P or 72#P authentication ser;er. *+ ,our

*SP app!ies encr,ption se!ect a needed ;a!ue +ro the Enc2"tiondrop-down !ist.

)1


22/24


10. For connection of PPTP + Dynamic IP or !TP + Dynamic IP type i+

,our *SP has pro;ided the address o+ the D4S ser;er in the IP sectiondese!ect the Otain DN( se3e addesses auto#aticall2chec6o and +i!! in the Pi#a2 DN( se3e+ie!d. #hen in the 8PN

section enter authoriation data pro;ided , ,our *SP "the usernae"!ogin$ in the Usena#e+ie!d and the password in the Pass'odandPass'od con!i#ation+ie!ds$ or se!ect the uired. *n the 8PN se3e addess+ie!d enter the *P or %7 address o+ the PP#P or 72#P authentication

ser;er. *+ ,our *SP app!ies encr,ption se!ect a needed ;a!ue +ro the

Enc2"tiondrop-down !ist.

11. *+ needed +i!! in other +ie!ds on the page in accordance with data pro;ided

, the *SP.

12. C!ic6 the (a3eutton.

))


23/24


Saving Settings t! (!n%v!latile 'em!ry

*n order to a;oid !osing the new settings upon hardware reoot "accidenta! or

intentiona! power-o++ o+ the de;ice$ it is recoended to sa;e the settings to

the non-;o!ati!e eor, o+ the access point.

C!ic6 the (a3e>Reoot!ine in the top-page enu disp!a,ed when the ousepointer is o;er the (2ste#caption.

ait unti! the access point is reooted. 4ow ,ou can use it to access the*nternet or access the we-ased inter+ace o+ the access point to con+igure

additiona! paraeters "+or detai!ed description o+ e;er, page o+ the we-ased

inter+ace see the (User Manual) docuent$.

),


24/24


+E*?NI*A. (UPPOR+

@ou can +ind so+tware updates and user docuentation on our wesite.

D-7in6 pro;ides its custoers with +ree support within the product?swarrant, period.

Custoers can contact the technica! support group , phone or , e-

ai!/*nternet.

FOR +E.EP?ONE NU@BER( AND ADDRE((E( OF D-.IN4

OFFI*E(

MANUAL TP-LINK ACCESS POINT LOBBY.pdf

Documents

Transcript of MANUAL TP-LINK ACCESS POINT LOBBY.pdf