Manual to update to R-nethandicare.blob.core.windows.net/media/...til-R-Net-Levo-Combi-Englis… ·...
Transcript of Manual to update to R-nethandicare.blob.core.windows.net/media/...til-R-Net-Levo-Combi-Englis… ·...
Man
To change the Pilot+ control Step 1: Bring the chair into seating ptwo screws (red arrows). Step 2: Bring the chair into standing the main fuse/switch.
ual to change the control from Pilot+ to R-net
to the R-net control you need around 2
position and take off the rear cover plat
position and raise the lift to the top po
2 hours.
te. Untighten the
osition. Switch off
Man
Step 3: Remove the Pilot+ joystick, funtighten the screws (red ar Step 4: Remove the joystick cable, c Step 5: Remove the plugs from the l
ual to change the control from Pilot+ to R-net
first plug out the joystick cable (green arow).
ut the cable tie’s (red arrows).
imit switches on the back.
arrow), then
Man
Step 6: Remove the plugs from the l Step 7: Cut all cable ties (red arrows
ual to change the control from Pilot+ to R-net
imit switch ES20.
s) from the cable harness under the seaat plate.
Man
Step 8: Open the cable conduit and r Step 9: Open the battery cover and sRemove the plate with the lim Step 10: Put the limit switch plate on with the battery-pins. Open t
ual to change the control from Pilot+ to R-net
remove the cable harness.
secure the cover with a cable tie that itmit switches by untighten the 4 screws
the batteries, but take care that they dthe ALM-box by untighten the 2 screws
t stays open. (red arrows).
don’t make contact s (red arrows).
Man
Step 11: Remove all the cables from t Step 12: Remove the cables from the plugs, press on top of the pocable plug. Then remove the
ual to change the control from Pilot+ to R-net
the ALM-box, then remove the whole AL
Power Module, take care with the poweower cable plug to remove it and on the Power Module
LM-box.
er and the motor e side of the motor
Man
Step 13: Remove the jacks from the gframe. Step 13b: If you have light, you also necables. First you need to remThen open the lights and indout all the light cables.
ual to change the control from Pilot+ to R-net
grey limit switches (red arrows) at the f
eed to update this with new cables. Remmove the cable bushing at the front of ticators and unplug the cables. Cut the
front of the basic
move the old he basic frame. cable ties and take
Man
Step 14: Change the grey limit switch Step 15: Mount the bushings of the grbit easier if you remove the b Step 15b: If you have light on the chair
Seat
ual to change the control from Pilot+ to R-net
es on the plate to the new version.
rey limit switches on the front of the babatteries. Then plug in the actuators.
r, mount the light cables on the front
Seat
Back
Seat
Lift
Lift
asic frame. It is a
Back
Lift
Back
Man
Step 16: Screw the ISM and the new P Step 17: Put the plate with the Power Velcro (hook-and-loop fastenconnect the ISM and the Pow
ual to change the control from Pilot+ to R-net
Power Module on the support plate.
Module and the ISM in the basic framener). Then plug in the power and the mwer Module.
M5x20
M5x12
e and mount the otor cables and
Man
Step 18: Connect the grey limit switch Step 19: Plug in the joystick cable andPower Module and ISM.
Backrest (B) jack no. 1
Seat (S) jack no. 2
ES 22/23
Joystick cable
ual to change the control from Pilot+ to R-net
hes to the ISM:
d connect the cables from the other lim
Lift (L) jack no. 3
ES 20
it switches to the
ES 2/3
Man
Step 19b If you have light you also ne Step 20: Mount the blue tilt switch to the limit switch plate and the
Light left
Light right
M3x15
ual to change the control from Pilot+ to R-net
ed to plug in the light cables.
the tilt switch support. And mount the e welded block.
It canswitchin thathe su
Take care that the cable of the tilt switch is facing backwards, otherwise it won’t
work correct.
support between
n be that the tilt h reacts too fast, at case just bend upport a bit more to the top.
Man
Step 21: Put some order to the cablesarrows). Step 22: Put the cable harness into thon the cable conduit. Step 23: Put the cable guard over the
ual to change the control from Pilot+ to R-net
s and tighten them with cable ties to the
e cable conduit and put the cable cond
cable harness and close the cable cond
Shift the c
e motor cables (red
uit cover halfway
duit.
cover to the front
Man
Step 24: Mount the cable harness withplate. Step 25: Mount the plugs of ES20 and
1
ual to change the control from Pilot+ to R-net
h some cable ties (red arrows) to the re
d fix it with cable ties (green arrows).
3
2
ear of the seat
Man
Step 26: Mount the plugs of ES 2/3 anarrows). left side ES 2/3 Step 27: Mount the joystick holder to
1
2
ual to change the control from Pilot+ to R-net
nd ES 22/23 and tighten the cables with
right side
the joystick.
3
4
M5x8
h cable ties (green
ES 22/23
2
1
Man
Step 28: Mount the joystick to the braties (green arrows). Step 29: The chair should work now. Gjoystick cable with a cable tieposition and tighten the cabl
M6x16
ual to change the control from Pilot+ to R-net
acket on the armrest and fix the joystic
Go into the lowest seating position and e to the seat plate (green arrow). Thene to the limit switch cable.
k cable with cable
tighten the go into standing
Man
Step 30: If you have light, you just nethe guiding on the front of thon the left and on the right h Then put the light cables throbulbs. Now you can mount th
ual to change the control from Pilot+ to R-net
eed to finish the mounting of the light che basic frame (red arrow), and throughhand side of the basic frame (green arro
ough the light holders and mount the hhe light covers.
cables. Go through h the two guidings ow).
holders with the