:ofecQUICK START MANUALQtel ADSL WiFi RouterPMCE_B_WF_007_AEStep By Step User Guidance Qtel ADSL WiFi RouterThank you for buying the Thomson TG585 v 7 ADSL2+ Router.This short booklet takes you through the steps you will need to follow to install your equipment and get your Home WiFi around your home.If you have any diffculties or need to speak to a Qtel specialist, please call us on 111.Make sure your ADSL line is activated.GETTING STARTEDStep 1: Power on the Thomson TG585 v 7 ADSL2+ Router.Step 2: Connect your computer or laptop to the Thomson TG585 v 7 ADSL2+ Router using network cable (RJ 45 cable).Confguring the Thomson TG585 v 7 ADSL2+ Router for Qtel ADSLStep 3: On the computer open Internet Explorer browser (or other internet browser in your computer), in the address bar type http://192.168.1.254, page display.Enter the user credentials (common for all users), User name = Administrator, Password = connect2th.zStep 4: Click on Thomson Gateway and then on Setup.Step 5: A small window will pop-up Welcome to the Thomson Gateway Easy Setup Click on Next.Step 6: Select Routed PPP, and then click Next.Step 7: Confgure RoutedInternet Connection. VPI/VCI = 8.35Connection Type = PPP overEthernet (PPPoE) Click on NextStep 8: Enter the Qtel ADSL user name and password(unique for each user).User Name = xxxxxxxx Password = **************Click on NextQtels ADSL customers arekindly requested to call 111to obtain their user name and password. a+Step 9:Enter the user credentials (common for all users).User name = Administrator Password = connect2th Click on NextStep 10: Please wait until the device is confgured Confguring your Thomson Gateway Please wait . Wait until the window shows Completing the Thomson Gateway easy SetupClick on Finish to close the set-up.Step 11: To verify the confgurations, connect the Thomson TG585 v 7 ADSL2+ Router to DSL line. There are 5 LED on front side of the CPE which denote the following: 1st LED denotes POWER ON 2nd LED denotes Ethernet connection 3rd LED denotes WiFi 4th LED denotes ADSL line status 5th LED denotes successful Internet connectivity Verify 1st, 4th and 5th LED are glowing. sStep 12: On the computer open Internet Explorer browser, in the address bar type http://192.168.1.254, page display. Verify under Broadband Connection Connected as shown below:cCHANGING WIRELESS SSID AND WEP SECURITYSSID: is wireless or WiFi network name on your router WEP Security: is your wireless or WiFi network password Step 13: On the computer open Internet Explorer browser, in the address bar type http://192.168.1.254, page display.Click on Home and then on Wireless. .Step 14: Click on Confgure.Step 15:Confgure WirelessaStep 15:Confgure WirelessTo enable WiFi, tick on Interface Enable. To change SSID, enter the desiredname at Network Name (SSID).To enable WEP security, select:Use WEP Encryption WEP Key Length = 64 bitWEP Encryption Key = xxxxxxx To save changes,click on Apply. Note: WPA settings are also available.8.WPA : : .Interface Enable SSID .(Network Name) (SSID) WEP .Use WEP Encryption WEP Key Length = 64 bit WEP Encryption Key = xxxxxx .Apply 7.Confgure : WEP SSID . :SSID. :Security WEP : . http://192.168.1.254 Wireless Home 65 : . http://192.168.1.254. Broadband Connection connected .) ( : Administrator = connect2th = Next : Confguring your Thompson Gateway.Please wait Completing the Thompson Gateway easy Setup . Finish . : .DSL ADSL2+TG585 v 7: CPE ADSL . 43.Setup Thompson Gateway : Welcome to the Thompson : .Next Gateway Easy Setup.Next Routed PPP : .Routed Internet Connection : VPI/VCI = 8.35: PPP over Ethernet (PPPoE)Next : .Qtel ADSL ) ( xxxxx = xxxxx = Next 111 Qtel ADSL . Qtel ADSL WiFi Router .ADSL2+ TG585 v 7 . .111 . ADSL :.ADSL2+ TG585 v 7 : : .(RJ 45) ADSL2+ TG585 v 7Qtel ADSL ADSL2+ TG585 v7 : . http://192.168.1.254 = .) ( .connect2th = Administrator2ADSL WiFi Router Qtel ADSL WiFi Router