Manual for Greenhouse STRONG - Dancovershop · 2 TECHNICAL CERTIFICATE Description Greenhouse...
Transcript of Manual for Greenhouse STRONG - Dancovershop · 2 TECHNICAL CERTIFICATE Description Greenhouse...
20-03-2018
forGreenhouse
STRONG
Manual
3,0m
2,1m
any length multipple to 2m min 4m
2
TECHNICAL CERTIFICATE
DescriptionGreenhouse STRONG is designed for creation microclimate favorable for growing garden
crops on cottage and household plots. Greenhouse might have variable length depending on customers’ desire. Required length of
greenhouse is provided by purchasing of packages with extending inserts. Each insert add 2m to base length. Base length is 4m. Height of installed frame is 2.1 m
The frame of the greenhouse is made of galvanized iron and is to be assembled with screws and
angles. Complete set includes all that is needed for fastening of coverage. Greenhouse may be completed with coverage on buyer’s request. Greenhouse has two door openings and two small windows in opposite ends.
Greenhouse base requires 3 sheets of cellular polycarbonate 2.1*6m with 4mm thickness. For each Inserts - 1 sheet of cellular polycarbonate 2.1*6m
Perform assembling and operation of the greenhouse in strict accordance with the manual and operating rules stated in the technical certificate. Please keep this technical certificate for further reference.!
Operation rulesBefore the start of operation, the greenhouse should be assembled and installed as prescribed in the manual. When the greenhouse is assembled by a third party the customer should supervise the quality of works to ensure compliance with the present manual. Some detail have extra holes due to uniformity of details. During assembly, be careful not to damage the parts, because until they
a diameter of 4mm or mandrel with a conical end. During assembly of the frame details’ connections
assembly rules and cause of removal warranty support by manufacturer.Do not install the greenhouse too close to buildings or trees where masses of snow/ice can fall on it. Recommended distance is at least 2 m. The greenhouse is designed to withstand wind at the speed below 24 m/sec. The greenhouse cladding should not be removed for the winter period if snow load is limited. If the greenhouse is left unattended for the entire winter the customer should either remove the cladding or estimate the possible snow load. For the frame assembled with all parts including strainers and braces, the maximal snow load begins when the layer of snow weight is 180 kg per 1 sqm of horizontal surface, which corresponds to regulative snow load of IV snow region (in accordance
against snow load in the following areas: Northen areas in Russia, the Scandinavian countries: Finland, Sweden,Norway, Denmark.
3
TECHNICAL CERTIFICATE
The company reserves the right to make changes in the greenhouse design
Warranty liabilities
1. The manufacturer is responsible for the completeness of the product. 2. The manufacturer is responsible for assemblability of the greenhouse in accordance with the instructions.
4. Term for making claims is 24 months from the day of purchase
Terms of warranty provisions
Cleaning and washing sheets of polycarbonate.
Warranty does not apply to cases of:1. Greenhouse installation in violation of instruction requirements 2. Violation of the rules of operation.3. Inappropriate use of the greenhouse.4. Deformation of the greenhouse as a result of ground movement. 5. Floods, hurricanes and other natural disasters.
1. Rinse the sheet with warm water.2. Wash the sheet with a solution of mild soap or with a household detergent and warm water, using a soft rag or a sponge to remove dirt.3. Rinse with cold water and wipe with a soft cloth.
Never use abrasives or highly alkaline cleaning compositions for cleaning polycarbonate sheets. Dry rubbing of the surface will damage the protective layer of the cladding and shorten its shelf life. Never rub the surface of polycarbonate sheets with brushes, metallic cloth or other abrasive materials.
When disinfecting the greenhouse from pathogens causing fungal and bacterial diseases, do not use «sulfur blocks» to avoid frame corrosion (blackening).
4
1 L=0,92 m х4
2 L=0,96 m х12
2в L=0,96 m х6
3 L=0,14 m х4
4н L=1,62 m х2
4в L=1,62 m х4
4вк L=1,62 m х2
4нкп L=1,62 m х2
4нкл L=1,62 m х2
5 L=0,09 m х4
8 L=1,04 х4
9-1 L=0,981 m х4
9-2л L=1,4 m х2
9-2п L=1,4 m х2
10 L=0,82 m х4
11-л L=1,02 m х2
11-п L=1,02 m х2
12д L=0,756 m х8
12ф L=0,320 m х4
13д L=0,713 m х6
13ф L=0,713 m х4
14 L=0,958 m х4
15 L=1,0 m х4
16 L=0,737 m х2
17 L=1,4 m х2
18 L=1,1 m х4
19 L=0,99 m х4
20 L=0,34 m х4
21 L=0,35 m х4
seal loop 3,7 m
seal door 8 m
seal side wall 12 m
5
tubeamplifier х4
bracket х8
hook for doors and windows х4
bracket for the hook х8
loops for doors and windows х8
workpiece for locking (turner with 2 elastic nozzles) х4
тtube bend spinner х1
handle х8
pin х4
screw М4 х 8 х534
screw М4 х 10 х50
screw М4 х 25 х116
screw М4 х 35 х32
self-tapping screw х6
nut М4 х732
washer М4 х144
special wrench х1
adhesive tape х1
1№
4ВК
№4В
К
№4В
№4В
№4В
L=1,05m х4
L=1,0m х4
top bandage х5
bottom bandage х10
bolt М6 х 60 х10
nut М6 х10
washer М6 х20
Double-sided tape L=8,2m
х1
Please see detailed list of parts for Insert on page 27
6
№2В№2В
№2В№2В
№4ВК№2В
№2В
№2В№4В
х4
х4
M4
x8 х2
х2
M4
x8
№2В№2В
№2В№2В
2
3
№2В
№2В
№4В
№2В
№4ВК
№2В
№2В
№2В
№2В
х4
х4
M4
x8
х2
х2
M4
x8
7
№4Н
КП
№4Н
КЛ
№4Н
4
5
№4Н
№4Н
№2
№4Н
КЛ
№2
№2 №4Н
№2
№2
№2
№2 №2№2
№2№2
№4Н
х4
х4
M4
x8
х2
х2
M4
x8
х4
х4
M4
x8
№4В
8
6
7
х10
№2 №2№2№2
№2 №2№2
№2
№1
№1
№3
№3
х3
х3
х1
х1
M4
x8
adhesive tape
screw М4х8
bottom bandage
№1
№3
9
8№
1
№1
№1
№1
№1
№1№
1
№1
№1
№1
№1
№4Н
№2 №2№2
№2
№2 №2№2
№2
9
х4
х4
M4
x8
10
10
№9-
2Л
№11Л
№8 №10
№10
№9-
2
№11Л
№10
№8
№9-
1
№9-
1
№3
№9-1
х2
х2
M4
x8
х4
х4
M4
x8
х4
х4
M4
x8
х2
х2
M4
x8
11
№8
№8
№11П
№4ВК
№4НКП
№11П
№9-
2П
№9-
2
№10
№9-
1
№1
№2
х2
х2
M4
x8
х2
х2
M4
x8
х2
х2
M4
x8
х2
х2
M4
x8
12
11
№18
№18
№19
№18
№19№
1
№19
№17
№17
№21
№2В
№2В
№21
№20
№20
№2
№2 №2
№4Н
№4Н
№4Н
№1
№4В
№4В
х6
х6
M4
x8
х2
х2
M4
x8
х4
х4
M4
x8
13
№17
№18
№18
№19
№19
№19
№18
№2В
№2В
№21
№21
№20
№2
№2№2
№4Н
№4Н
№1
№1
№4Н
№4В
№4В
№20
х6
х6
M4
x8
х2
х2
M4
x8
х4
х4M
4x8
14
12
№2В
№9-
2П
13№4ВК
№4НКП
№4НКП
№4ВК
№4НКЛ
№4НКЛ
№2В
№9-
2Л
х1
х1
M4
x8
х1
х1
M4
x8
х1х1
M4
x8 х1
х1х1
M4
x8 х1х1
M4
x8
х1
х1
M4
x8 х1
х1
х1
M4
x8 х1
х1х1
M4
x8 х1
15
14
N13ф
№13ф №13ф
N12ф№12
ф
№12
ф
N12фN16
№16
N13ф
х2
х2
M4
x8
х4
х4
M4
x8№13д
№13д
№13д
№13д№
12д
№12
д№
12д
№12
д
№12
д№
12д
N15
N15
N14
N14
№15
№15
№15
№15
№15
№15
№14
№14
№14
№14
N13д
N13д
N13д
N12д
N12дN12д
N12д
х2
х2M4
x8
х4
х4
M4
x8
х7
х7
M4
x8
х8
х8M4
x8
х2
х2
M4
x8
х4
х4M4
x8
16
15
L1
L2
Cellular polycarbonate shall be installed strictly defined side out (towards the sun), which has a protective layer. The protective layer is usually at the side with the inscriptions on the transport film. The film on the other side of sheet is transparent. After marking the sheet, but prior to its cutting, make a mark on the protected side of the sheet for each piece: after removal of the transport film sheet sides are not visually different. The transport film is stripped from both sides immediately before fixing the cladding on the frame.
Sections of polycarbonate with open honeycombs should be covered by adhesive tape.
16
2095
80
5
1480
21
00
6000
330
20
95
2100
L1=L2!
17
17
х1 х2
х1
х2
х1 M4
x10
х2
№5
х4
х4
M4x
10
M4
x25
х17х17
х17
20..25мм
х1
х1
M4
x25
х1
х1
18
18
№5
х2
х1 M4
x10
х2
х2
х1 M4
x10
х2
х4
M4
x10
х4
х1
х1
M4
x25 х1
20..25мм
M4
x25
х7х7
х7
х1 х2
х1
х1
19
19
№9
х1
M4
x25 х1
х1
х1 х1
х1 х1
х1 х1 M
4x10
х1
х1
х1
M4
x25
х15 х15
х15
M4
x35 х16
х16
х16
20
5,15м
№9-
2
№12
д№
5
х1 х1
х2
20
21
№9
х2
M4
x10 х2
2х6м
21
222
12000
2000
10
00
10
54
21
00
х1
х2L=1,05м
Double-sided tape
The arrow on the details is directed to the front side greenhouse
Cellular polycarbonate shall be installed strictly defined side out (towards the sun), which has a protective layer. The protective layer is usually at the side with the inscriptions on the transport film. The film on the other side of sheet is transparent. After marking the sheet, but prior to its cutting, make a mark on the protected side of the sheet for each piece: after removal of the transport film sheet sides are not visually different. The transport film is stripped from both sides immediately before fixing the cladding on the frame.
Sections of polycarbonate with open honeycombs should be covered by adhesive tape.
22
24
23
х16
M4
x25
х16
!Do not fully tighten!
х1
1054
23
25
х2
х2
M4
x25
х2
26
M6
x60 M
6
х1
х2
х1х1
24
27
х1
х3
M4
x25
х3
1 m
1000
25
28
26
866
40
60
10
00
10
00
10
00
10
00
2988
FOR INSTALLING ON FUNDAMENT
1061
А
Б
60
60
21
21А
Б
А
1 L=0,92 m х4
2 L=0,96 m х12
2в L=0,96 m х6
3 L=0,14 m х4
4н L=1,62 m х2
4в L=1,62 m х4
17 L=1,4 m х2
18 L=1,1 m х4
19 L=0,99 m х4
20 L=0,34 m х4
21 L=0,35 m х4
L=1,0m х4
Detailed list of parts for Insert
27
Contact information
Head office:Dancover A/SNordre Strandvej 119 G3150 HellebækDenmark
For more informationplease visit:www.dancovershop.com
National contact
Denmark: 70 26 76 [email protected]
UK: 020 8099 [email protected]
Spain: 911 436 [email protected]
Italy: 02 479 21 [email protected]
Germany: 041 0266 [email protected]
Switzerland: 0840 [email protected]
France: 0975 181 [email protected]
Austria: 0662 [email protected]
Sweden: 040 233 [email protected]
Finland: 0 931 581 [email protected]
Nederland: 0 858 880 [email protected]
Poland: 22 300 [email protected]
Ireland: 0 151 33 [email protected]
Luxembourg: +49 041 0266 [email protected]
Portugal: 308 800 [email protected]
Belgium: 0 28 08 08 [email protected]
Norway: 231 00 [email protected]